Search Documents

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By Adam Bedell, Jack Raymer, Brad Crenshaw

Tunnel contracts often include provisions for pre-excavation probing and grouting for areas ahead of the tunnel heading. If grouting triggers are met, tunneling stops, and grouting is performed. There is substantial variation within the underground industry on what criteria are applied to the grout verification hole that is drilled post-grouting and before excavation resumes. The criteria for determination of the effectiveness should be dependent on the geology and local hydrogeologic conditions. The purpose of this paper is to present specific criteria that can be used by a practitioner to determine whether tunneling can resume or if additional grouting is required.

Dec 1, 2022

Several years ago, North American mining companies began to realize they needed to expand their spheres to remain viable. This strategy has been successful, according to Robert W. Schafer. Today, companies from other continents have also recognized the need for an international view for long-term growth and viability, he said. Schafer is vice president for exploration with Kinross Gold. He was the program chairman and moderator of the keynote session at the 1997 SME annual meeting, held in Denver, CO, Feb. 23-27. The theme of the meeting was "Minerals - Serving the Global Community." A record attendance of more than 6,000 people participated in the meeting, which featured 415 exhibitors occupying 582 booths. The title of the keynote session was "Corporate Perspectives on a Global Minerals Industry." Each of the three keynote speakers discussed a different perspective of a global minerals industry.

Jan 1, 1997

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By A. D. S. Gillies

Diesel engine particulate matter pollution is a matter of concern currently in underground mines worldwide. A number of real-time Diesel Particulate Matter (DPM) monitors have been developed in recent years; two of these by the National Institute of Occupational Health and Safety (NIOSH) in the US. One, the D-PDM, is based on an adaption of the successful NIOSH?s Personal Dust Monitor (PDM) unit which is being taken up very successfully for mine respirable dust monitoring. The D-PDM measures all particulate matter within a sub-micron range as classified nominally at 0.8 micrometers by a purpose developed cyclone. The other, the FLIR Airtec, measures the Elemental Carbon (EC) component of DPM by a laser scattering approach. Both instruments have been evaluated underground in robustness and reliability testing in coal mines by the authors. Real time DPM monitors allow greater understanding of the sources and levels of DPM pollution in underground activities. They allow engineering evaluations to determine how conditions can be improved or mining personnel relocated to lower concentration levels. Studies are discussed that examine DPM concentrations from vehicles under varying ventilation conditions. Some of these concern tests undertaken during high activity longwall face moves. They focus on evaluating DPM during the various phases of the face Chock Shield moves. An initiative in some mines has been to limit the number of vehicles in the mining section or panel by the use of a Tag Board or Traffic Controller at the panel travel road entrance to manage exhaust DPM and gases. Diesel tags or tokens are used to control the number of vehicles entering a section or panel and so limit level of pollution. Summation of DPM levels from points monitored throughout a panel demonstrates increasing DPM levels from influence of additional equipment in series within the ventilation circuit. An alternative approach is to invest in underground continuous real-time monitoring of exhaust gases, DPM and section air quantity and integrate this information to determine whether an additional vehicle can enter without exceeding diesel target limit. This optimizes the access of diesel vehicles and replaces the existing manual tag board system. Real-time DPM monitoring allows the industry to pin-point high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. Identification of high DPM zones allows efficient modification of mine ventilation, operator positioning and other work practices to reduce underground miners? exposures.

Jan 1, 2012

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

By Bianca Cruz, Tom Lankiewicz, Kent Sorenson, Karrie Radloff, Elizabeth Deyett, Dayal Saran, Michaeline Albright, Dan Stigers

Biology opens a new frontier for the mining industry. With rising environmental concerns, the need to couple conventional chemical and physical technologies with sustainable approaches is pressing. At Allonnia, we harness microbial processes to create innovative and environmentally responsible technologies with broad applications. The native microbial community (microbiome) remains largely unexplored at most mining sites, unlike the geochemical environment. The exploration of complex biological reactions that could transform mining technology is just starting and holds vast possibilities, spanning bio-cementation, carbon sequestration, ore beneficiation, water mitigation, bioleaching, metals recovery, and more. Allonnia has collected samples from mine sites in Australia, Africa, and North America to characterize the microbiome and uncover the genetic potential present in mineral-rich environments. We are evaluating microbial metabolites that selectively solubilize gangue from various ores. In addition, biological reactions hold promise as tailings stabilizers. Our early efforts illustrate exciting prospects for harnessing biology’s potential in mining.

Feb 1, 2024

Explosives are used to mine coal. Any blast results in three size categories of products, namely over-, middle-, and under-size. Boulders can still be broken smaller in further operations after blasting. The under-size, for instance coal fines, negatively affects the mining efficiency. Their reduction ensures better returns. The paper concerns investigations aimed at reducing coal fines' generation. Inherent fractures are identified as one of source of fines. The discussion is therefore centered on establishing a relationship between the fracture occurrence, the explosive properties and the blast outputs evaluated in terms of the fines generated.

Jan 1, 1996

By Louis Schaarschmidt, Helmut Mischo, Ibrahim Alsalamin

In order to store high-level radioactive waste underground, the German repository concept considers clay, crystalline and salt formations as suitable host rock materials (National Citizens’ Oversight Committee, 2024). The current research projects of the Chair Underground Mining Methods at TUBAF (Technical University Bergakademie Freiberg) in nuclear waste repositories mainly focus on storage within salt formations. In this scenario, the high-level radioactive waste is supposed to be packed into specifically designed containers and then transported underground and emplaced in horizontal storage drifts. The residual temperature of the radioactive waste leads to the question if there are optimization possibilities for waste handling, the storage and the long-term emplacement of such high temperature level waste. A deeper understanding of the heat transmission from the container into the host rock might lead both towards possibly shorter surface interim storage times as well as size optimization possibilities of the repository itself. TUBAF has conducted research that successfully proved that an optimized container positioning yields more favorable thermal patterns and can be achieved with conventional mining equipment.

Feb 1, 2025

By X. Zhu, L. Chen, R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study was to develop a suitable flowsheet to extract rare earth elements (REEs) from coal ash. Only the findings from the first part of this study is being reported at this time. A total of fourteen coal samples of different ranks were examined for REEs concentration. An anthracite coal sample, originating from Pennsylvania having more than 700 ppm (in the coal ash) was selected for the REE extraction tests. The experimental program completed so far included high temperature leaching using nitric acid, followed by the solvent extraction tests. A 4x2x2 experimental design was used to conduct a total of thirty two high temperature leaching tests by varying acid molarity (at 4 levels), solid content (at 2 level) and leaching time (at 2 level). The highest LREE (light REE) recovery of 90% and HREE (heavy REE) recovery of 94% were obtained from the most optimum leaching test condition while maintaining the impurity recovery to the leachate at less than 40%. Solvent extraction experiments were conducted to recover the REE’s from the above leachate solution using a variety of organic extractants including, TBP, Cyanex, D2EHPA and their combinations. D2EHPA was found to be the best extractant during this SX text series providing nearly 99% recovery of REEs. INTRODUCTION The demand for rare earth element and other strategic metals (REM) in the world is rapidly increasing due to their use in a variety of high technology applications. More than 100,000 tons of rare earth oxides (REO) are being used worldwide on an annual basis. However, we have less than 10% of the world reserve of rare earth element (REE) mineral deposits in the US. More than 60% of rare earth oxide (REO) was imported to the US from outside (mostly from China) in the year of 2013. However, China’s institution of export quota has significantly reduced the supply of REMs to the U.S. Hence, new ways of producing REM and/or finding substitutes for those metals for the high-tech applications need to be invented/discovered in a timely manner. Coal Combustion Byproducts (CCBs), which are discarded as waste materials in most cases, are known to contain REEs (in low concentration) that could be extracted using a suitable process flowsheet. This may be a worthwhile route to pursue considering the short supply of REMs and the abundance of coal ash in thousands of ash ponds in the US. On an annual basis, more than 110 million tons of Coal Combustion Byproducts (CCBs) are being produced while satisfying our nation’s need for electricity (ACAA, 2014). However, less than 50% of these CCBs are being successfully used in various applications and the remainder is being dumped as waste materials in the landfills and ash ponds."

Jan 1, 2017

By F. Kennedy

Consolidation Coal Company (Consol) supports an active R&D effort to improve the safe, productive mining of coal and to utilize coal in an environmentally acceptable manner. Attention will be focused on degasification of coal seams, continuous coal transport systems, earth sciences activities, and coal combustion. Brief mention will be made regarding the SO2 emissions control programs. The research program constitutes about 1.0% of Consol coal sales which positions Consol as the preeminent coal company supporting broad-based research addressing the full spectrum of the various problems associated with utilizing the nation's abundant reserves of economical, readily available fuel.

Jan 1, 1989

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By L. F. McHugh

Molybdenum conversion operations discussed in this paper encompass all major operations commercially used to upgrade molybdenite concentrates to various refined products. More emphasis is placed on discussion of key pyrometallurgical unit operations. These operations conducted at Metec include roasting, sublimation, and hydrogen reduction

Jan 1, 1986

By Floyd M. Thorman

Gypsum is the crystalline chemical compound CaS04?2H20. A close chemical relation - and frequently occurring with Gypsum ? is Anhydrite which is Cask. Gypsun has wide commercial use because relatively simple heat processing reduces it to Plaster of Paris. While Anhydrite can be converted to Gypsum and thence to Plaster of Paris, the procedure is not simple and is quite costly. Anhydrite, however does have use in the agricultural field and in the Portland Cement industry. Occurrence of Gypsum in the earth structure is usually near or at the surface. Most underground mining is at 60 to 100 feet although one mine in southwest Virginia reaches a depth of 1300 feet. Gypsum is one of our softest minerals, rating only 2.0 on the Mohs scale of hardness. Specific gravity is 2.3 to 2.4. It is soluble in water but only slightly so. Interestingly, it is more soluble in cold water than in hot. For example, one part Gypsum dissolves in 370 parts water at 106° Fahrenheit while at 212°F. the water requirement is 452 parts. Compressive strength of massive Gypsum runs about 3000 lbs. per square inch. Color ranges from grey and brownish-grey to white.

Jan 1, 1973

By H. A. Taylor

Bismuth, one of the heavier chemical elements, is a pinkish metalloid that is chemically related to antimony. It is a byproduct of lead and tungsten extraction and, to a lesser extent, of copper and tin extraction. Antimony is a metalloid and less heavy chemical element, an extraction coproduct of metals such as lead, silver and gold. While both bismuth and antimony are metalloids, their major uses are as chemical compounds. The most frequently updated resources that always cover bismuth and antimony are the Bismuth Advocate News (BAN) and link at www.basicsmines/bismuth and the frequently updated Basics Mines Update blog at http://basicsmines-update.blogspot.com. The Bismuth wiki on Wikipedia also can be very helpful.

Jan 1, 2010

By Ching-Liu Wu, John Hawley, Andrew H. Liu, James Chai

The Hatch Mott MacDonald/Bechtel Joint Venture team is designer and construction manager for the 5.25-mile Tunnel Segment of the overall 16-mile Silicon ValleyRapid Transit Project, which extends the existing Bay Area Rapid Transit (BART) system southward from Fremont to San Jose. The Tunnel Segment includes twin boredtunnels, mined cross passages, and three deep station excavations situated in highlyvariable ground, high ground water table, and a dense urban setting with high-risebuildings adjacent to the largest excavation. This paper will discuss design challengesthat have arisen with the excavations and the proposed solutions.

Jan 1, 2007

By William Hodder, Ehsan Alavi, Muhib Hussain

Disc Cutter Wear is influenced by several geological and technical factors and excessive wear can have a major impact on the excavation efficiency of Tunnel Boring Machines (TBM). Disc cutter replacement events cause a disruption to the construction schedule and costs, and should be minimized throughout the project to the extent possible. A well-executed cutterhead inspection and maintenance plan can help mitigate abrupt cutterhead interventions and reduce its effect on project schedule and cost. This paper examines cutterhead inspection and disc cutter replacement events as well as subsequent wear data recorded in the first 7km of the 10.3 km long, 6.3 m diameter Coxwell Sanitary Bypass Tunnel (CBT) project in Toronto, Ontario. The CBT alignment is mainly through Georgian Bay Formation shale.

Dec 1, 2022