Search Documents

By Seanley C. Suboleski

This paper examines the likely productivity improvements that have resulted from the introduction of technological advances in underground coal mining during the decade from 1977 to 1987. Included in these advances are the changes in longwall mining; the introduction of larger, more reliable, more repairable continuous miners and shuttle cars; the introduction of remote control and flooded-bed scrubbers; supersections; and other improvements. Procedural improvements are also examined and quantified, the unexplained gains in productivity are attributed to??other factors", among them an increasing maturity of the work force, stabilization of the mining laws, increased labor-management co-operation, and economic urgency.

Jan 1, 1990

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By John A. Dunn

The history of underground coal mining has developed through the years from a manual digging and loading process to the highly mechanized pro- cess that it is today through the use of electric power. Mine power systems have closely followed the continued pattern of improvement and mechanization, through necessity and the application of technological advances, At the beginning electric power used in coal mines was confined to haulage. Since d-c power was better suited to traction drives, mine power systems naturally developed using direct current. During this development, a number of street railway systems were in service, using 550 volts, and it was natural that mine trolley systems went in at 550 volts. As machines for mining operations developed and the number of operating mines increased, a safety hazard developed through the use of 550 volts. Most regulating agencies opposed the use of 550 volts, and after a time the maximum voltage permitted was limited to 300 volts hot line to ground. Up until this time most mines had operated with one central generating station, which served utilization power to the whole mine. Power demands were not very great and transmission losses were within reasonable limits.

Jan 1, 1964

By U. Cetin

The Nevada Test Site is located approximately 65 miles northwest of Las Vegas, NY. The site was primarily used by the Department of Energy for the field testing of nuclear weapons and contaminated by several million cubic feet of low-level radioactive wastes, heavy metals, volatile and non-volatile organics, and explosive materials. Leaching and transportation of these contaminants are creating severe environmental problems. The purpose of this study is to examine pozzolan, a natural alumina-silicate mineral, as a possible replacement of the existing impermeable barriers (clays). In the first phase of this study, radionuclide sorption characteristics of pozzolan were investigated. This paper will present the results of the sorption tests for the target radionuclides.

Jan 1, 1998

By Peter Schmäh, Tobias Engel

The E-Power Pipe technology was originally developed for the trenchless installation of protective pipes and pipelines of 10" to 28" diameter, over long distances of more than 4,000 ft. The twostage process combines elements from Horizontal Directional Drilling (HDD) and microtunnelling technology. A microtunnelling boring machine (MTBM) excavates the borehole using a specially designed, temporary jacking pipe. A Rack & Pinion jacking frame pushes the equipment during the pilot bore and pulls in the prefabricated pipe string in a second step. The slurry microtunnelling machine is equipped with a jet pump, creating the so-called AVNS machine type. A new generation of small hard rock cutting wheels complements this considerable achievement for the tunnelling industry

Dec 1, 2022

By John Todhunter

Longwall mining is certainly not new in the United States, having first been used in the late 1800's in Illinois, but the surging acceptance of the method is relatively new. The number of longwall installations in this country are nearly doubling annually as this method continues to prove itself as a coal producer's delight terms of operating cost, performance and safety. Since 1951, several longwall installations have been tried in Barnes and Tucker Company operations. Although all efforts actually proved that the system itself could be used in prevailing conditions, it was not until 1967 that a unit was put in use that proved competitive with regular mining equipment, both conventional and Continuous.

Jan 1, 1968

By James Wonneberg, William Edgerton

"Today’s underground construction megaprojects are tremendous feats of engineering on a massive scale, excavating through ground conditions once thought impossible, using new and innovative contracting practices. But one important truth remains unchanged; projects are built by people. What separates winning projects from the rest? Great people, working in great organizations. In straight-talk fashion this paper sets forth fundamental differences between good project leaders and bad ones, on topics ranging from client relations, design management, and scheduling, to use of the whiteboard, and everything in between. Broadly applicable to all corners of project delivery, this paper will resonate with project leaders from around the world and help identify skills necessary to succeed in the management of underground facilities. A NOTE FROM THE AUTHORS This is a training document, and not really a “paper” per se. We have attempted to tackle some big and potentially complex topics using bite-sized paragraphs, each of which are intended to promote thoughtful introspection and dialog. So please feel free to skip around, or even set this document down while you reflect on your own personal experiences, tactics, and philosophies. We have found that providing examples of “what not to do” is oftentimes more instructive than simply listing “what to do”, hence the Good/Bad format of this document. Please note that “PM” refers loosely to anyone on the project management team not just the “Project Manager”. We also wish to preface this with the following cautionary statements: • The authors do not pretend to be the “Good PM” in all cases. In fact, we’re almost certainly the “Bad PM” for some. We aim to improve on those areas. • It has been said that “The only real training for leadership is leadership.” (Antony Jay) We all started somewhere, and nobody has 20 years of experience on day one. • Converting this text into some sort of prescriptive checklist would be a disservice to the evolution of project management. Our world – and our awareness of it – is constantly changing. We must always be open minded to new ideas and different perspectives on project delivery."

Jan 1, 2016

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By T. Yalcin

It is well recognized that machine type and machine characteristics play vital roles in the successful application of froth flotation in mineral processing. Since the early 1900s, a multitude of machine designs have been and are still being introduced in an attempt to improve flotation efficiency. Machines based on mechanical agitation have been the most dominant in industrial practice. However, in recent years there has been a growing interest in pneumatic flotation units because of their claimed simplicity, low cost, high throughput and good metallurgical performance. This work was carried out to assess the effectiveness of pneumatic flotation on a magnetite ore. The method was applied using a prototype pneumatic flotation device that utilized a suitable nozzle for bubble generation. Important variables of the process were examined and optimized, including the nozzle size, air flow rate and froth thickness. Further tests were conducted to determine the influence of frother dosage and to explore the improvements that could be made on concentrate grade and recovery by cleaning and scavenging. Under the best test conditions, an iron concentrate was obtained with a grade of 66.4% Fe and a recovery of 97.7%. Particularly, the recovery was superior in comparison to that of mechanical flotation. This was attributed to the ability of pneumatic flotation to create and maintain a relatively thick froth layer.

Jan 1, 2002

By Dapeng Zhang, Brij Moudgil, Shibo Zheng, Chunhui Feng, Wenyi Song, Wending Xiao, Patrick Zhang

The separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. More than 50 percent of the phosphate reserve in Florida contains too much dolomite to process using current industry practice. The current way of producing phosphoric acid requires less than one percent MgO in the phosphate concentrate as the feed material. The Florida Industrial and Phosphate Research (FIPR) Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered three feasible options. Option I entails three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand, which could reduce MgO content in the final concentrate by 20 to 40 percent. Option II involves the crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9 percent MgO at about 87 percent P2O5 recovery. Option III is a gravity separation technique using an innovative separation jig, and its full potential remains to be demonstrated.

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables.

Jan 1, 1981

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By N. Aouad

Dump truck operators are exposed to whole-body vibration (WBV) levels that exceed the International Standard Organization (ISO) 2631-1. The WBV level measured by RMS acceleration value, for operator comfort, and long-term health and safety is under 0.315 m/s2 by these standards. However, fundamental research by Frimpong and Aouad (2009, 2012) and field experimental study by Kumar (1999) have shown that operators are exposed to extreme WBV levels exposing them to injuries and musculoskeletal diseases in the long-term. These extreme WBV values in the vertical direction are equal to 3.56 m/s2, 1.12 m/s2 and 0.87 m/s2 for the operator?s seat, lower-back and cervical regions, respectively. This paper will outline current research to solve these problems. Keywords: WBV, Truck Vibrations, MSC.ADAMS, Virtual Prototyping

Feb 27, 2013

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By G. Danko

Ventilation and refrigeration for mine climate modification, contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can be used to minimize the impact of these costs. There are several computer codes available including CLIMSIM?, to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely: what accuracy is required of the basic input parameters, in order for a certain precision to be obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed to the changes of the rock thermo-physical properties, the heat transfer coefficient and the wetness factor.

Jan 1, 1988

By Tim Hurley

On Friday, May 27, 1983 at about 6 p.m., an avalanche occurred at the Revenue-Virginius Mine. Six mine personnel and two contract diamond drillers were trapped when the avalanche covered and blocked the portal, the only access into the mine. The San Juan Mountain Range in southwestern Colorado is an old volcanic caldera. It has dikes and other intrusions, many of which are mineralized with sulfide ores rich in silver, gold, lead, zinc and copper. Several peaks rise above 4,260 m (14,000 ft) and the district has been the location of avalanches dating back to prehistoric times. This is evidenced by the numerous snow-slide chutes that are infamous enough to be named on topographic maps.

Jan 1, 2006

By Gordon M. Bell

Water has received little attention as a variable in flotation, even though it is a known fact that water hardness often has an adverse effect on purity and recovery, particularly on the flotation of non-metallic minerals. Because of this fact, process water used in some flotation plants is treated to reduce hardness to an acceptable level. In the laboratory, distilled water is usually used as the flotation medium in order to standardize conditions, whereas in flotation plants locally available water is used. At Rosiclare Works of Aluminum Company of America, Rosiclare, Illinois, where a vein-type of fluorspar deposit was being processed by flotation to make an acid-grade fluorspar concentrate until February of 1968 when the plant was closed, qualitative correlations had been observed between metallurgy and reagent consumption and the seasons of the year. The observed effects were thought to be due to seasonal variations in the quality of Ohio River water used as the flotation medium. Figure 1 shows the variations in total hardness and chloride contents of Ohio River water at Rosiclare for the period September 1964 through September 1967. During this period, the sulfate content varied from 85 to 245 ppm (as Na2SO4), the calcium from 90 to 160 ppm (as CaCO3) and the magnesium from 50 to 70 ppm (as CaCO3). The data in Figure 1 show that the total hardness and chloride contents are highest in the late summer and fall which are usually periods of low water and lowest in late winter and spring which are usually periods of high water.

Jan 1, 1970

By James R. Arnold, Cindy S. Jones, Michael F. Gleason, John O. Marsden, John G. Mansanti

INTRODUCTION The Chimney Creek Gold Mine (Gold Fields Operating Co. - Chimney Creek) is located 47 miles northeast of Winnemucca, Nevada, at the northern end of the Osgood Mountains. The operation is a wholly owned subsidiary of Gold Fields Mining Corporation, the North American branch of Consolidated Gold Fields PLC, London, England. The plant started up in November, 1987, less than three years after discovery of the orebody and three months ahead of schedule. Ore is mined in an open pit and is processed by combined dump leaching and milling techniques for gold and silver recovery. The mine is set to produce approximately 150.000 ounces of gold and 50,000 ounces of silver per year over a 12 year life at current reserve estimations. The mine was designed and constructed at a cost of $79.3 million with engineering and construction services provided by Davy McKee Corporation, San Ramon, California. Key Gold Fields operating staff were involved in the design of the facility from the start of the project: The Mine Manager, Plant Superintendent, Plant General Foreman, Maintenance General Foreman and Chief Metallurgist were all involved full time on the project within 5 months of the first ore discovery. Emphasis was directed at optimizing operating efficiency and in particular minimizing labor costs in the plant. It was recognized that a high level of instrumentation and control would be required to achieve this. The risk associated with the instrumentation and control systems implemented was to be minimized by using equipment and systems that had been proven in industry while utilizing the most cost effective, state-of-the-art technology available. The reliability of the overall control system was considered to be critical in view of the cost of downtime associated with the gold extraction plant. BRIEF PROCESS DESCRIPTION The dump leaching process treats approximately 1.2 million tons per year of low grade ore at an average grade of 0.035 oz/ton. Run of mine material is dumped on a lined leach pad and weak cyanide solution is applied by drip irrigation. Pregnant solution run off is pumped to carbon columns in the milling plant for gold recovery and the barren solution returned to the dump leach circuit. Average gold recovery is 60%. This process has little instrumentation and control associated with it. The milling operation treats 700,000 tons annually of higher grade ore (0.200 oz/ton initially, dropping to an average of 0.135 oz/ton after first two years). Recovery is directly related to head grade (fixed tail assay effect) and currently averages 96%. A single pass through a jaw crusher reduces run of mine ore to minus 12 inches. The ore is stockpiled and reclaimed by loader for grinding in a two-stage milling circuit consisting of a SAG mill and ball mill, the latter in closed circuit with hydrocyclones. Cyanide and lime are added into the SAG mill to start dissolution of gold as early as possible in the circuit. The ground product leaves the milling circuit at approximately 78% minus 200 mesh and is fed to an unique "double thickener" leaching-recovery circuit. This circuit has been discussed in detail in a paper by J. G. Mansanti et a1 (1). Two thickeners are arranged in counter- current configuration with three leach tanks. Overflow solution from the first thickener is treated by carbon-in-columns (CIC) for gold recovery with 85% of the soluble gold recovered onto this carbon. Underflow slurry from this thickener is pumped to the leach tanks, with a total retention time of 12 hours, and then gravitates to the No. 2 thickener. Overflow solution from the second thickener is used as a wash in the first thickener. Underflow slurry from the second thickener is treated in a carbon-in- pulp (CIP) scavenging circuit to recover the remaining 15% dissolved gold. Gold-loaded carbon from both the dump leach and milling circuits is stripped in batches using the Zadra hot caustic- cyanide elution process. Gold (and silver) is recovered from the hot strip solution by precipitation with zinc dust and the product recovered on Funda pressure filters. The precipitate is retorted to remove any mercury and then smelted into buttons. The buttons (approximately 80% gold, 15% silver) are shipped to an independent refiner in Salt Lake City, Utah, for further treatment.

Jan 1, 1990

In the last four years, 2007~2010, 9 out of 24 metal/nonmetal underground mine fatalities were caused by ground fall across United States of America (Mine Safety & Health Administration, MSHA). To reduce or eliminate incidents/accidents caused by ground fall, this paper clarified how to design and select ground support based on different ground conditions, how to use mine ground support standards, what geotechnical engineers and underground operators should do to keep mine production free of ground failures.

Jan 1, 2012