Search Documents

By CADEN VITTI, Barbara J. Arnold

Mine tailings, the byproduct of mining and mineral processing, are increasingly mass-produced as a result of increased demand for metals and minerals as well as the advancement in technology that allows for the exploitation of lower-grade ores. Lower grades can increase the volume of tailings that may contain new gangue minerals that should be evaluated for the presence of critical minerals and other valuable metals. The practice of reprocessing, while relatively new, is crucial to reducing environmental damages, obtaining valuable critical minerals from waste, and contributing to more sustainable repurposing and disposal methods. With the increase in tailings dam failures in recent years, there is a large motivating factor in remining and removing the potential hazard to benefit the safety of potentially impacted communities. In analyzing the perspectives of various domestic and international studies, this literature review will determine the feasibility of reprocessing and reutilizing mine tailings waste for a more sustainable future while exploring current practices that have benefitted ecosystems and communities.

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By R. R. Cellan

There have not been many opportunities to date for comparison between laboratory and commercial neutralization rinse data. Homestake Mining Company's Santa Fe project is one such comparison. This paper discusses laboratory procedures and results from a 100' leach pad height simulation column neutralization rinse test and compares principal data with that achieved in actual commercial leach pad neutralization rinsing procedures. Principal comparisons include the rate of WAD cyanide neutralization, decrease in effluent pH, stabilization of dissolved silver and copper, and the quantity of dissolved gold recovered during rinsing.

Jan 1, 1996

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By W. C. Painter

In 30 years of experience in Western Mines as Master Mechanic, Chief Electrician and Field Service Representative of Joy Manufacturing Company, I have seen a steady rise in the acceptance of A-C powered equipment for underground use in coal mines. This is also true for potash, gypsum and trona mines where coal mine type equipment and methods are used. This paper covers a large section of actual western mining practice with no theoretical calculations or predictions.

Jan 1, 1959

By H. C. Harrell

The Tennessee Valley Authority began employing geophysical well logging for foundation investigations in October 1973. Since that time more than 3,000 holes have been evaluated for engineering purposes. The Tennessee Valley Authority has not actively used geo-physical well logging for exploration of construction materials, but we feel that much of the information derived from geophysical logs for foundation exploration is applicable to the construction materials industry. This paper will then discuss geophysical logging as applied to foundation engineering and, by implication, the feasibility of use in construction materials exploration. The use of geophysical logging and percussion drilling instead of coring has greatly expanded TVA's data acquisition capabilities and has also resulted in substantial savings in time and money. Economical boreholes are obtained through the use of large percussion track drills (Figure 1). This equipment is capable of drilling through the overburden, setting steel casing on the top of rock, and drilling the rock beneath the casing. Holes as deep as 400 feet (121.9 m) have been drilled by this method.

Jan 1, 1977

Ceremonies for the induction of five mining industry pioneers into the National Mining Hall of Fame will be on Sept. 12, 2009 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. The five inductees are: Paul A. Bailey, 82, Richard T. Moolick, 89, William Braden and Alonzo Pawling and Henry Harnischfeger. Paul A. Bailly was president of Bear Creek Mining Co., the U.S. exploration subsidiary of Kennecott Copper, from 1961 to 1967. In 1968, he joined Occidental Petroleum Corp. and was tasked with creating the company?s international mining division, Oxymin, which he led as president through 1983. During his distinguished career, Bailly participated in numerous significant mineral discoveries, developed a new exploration philosophy and made important additions to the mineral exploration literature. William Braden was the first to recognize the immense potential of the El Teniente orebody in Chile. He founded Braden Copper Co. and developed the El Teniente Mine which now, 100 years later, remains the world?s largest underground copper mine. Braden?s endeavor survives to-day as the El Teniente division of the Chilean state copper company, CODELCO. T. (Dick) Moolick established a lasting legacy in the mining industry, first during a 35 year career with Phelps Dodge Corp. and then as the driving force in establishing the National Mining Hall of Fame and Museum in Leadville. The Hall of Fame and Museum ? a monument to the memory of the men and women who pioneered the discovery and development of the United States? natural resources ? has become one of the fi nest museums in the western United States.

Jan 1, 2009

By Feng Junfa, Du Feng, Li Huamin, Syd S. Peng

"The Ordos coal field is located in the northern midwestern part of China (Fig. 1). Since the mid- 1980s, it has been developed into one of the major coal fields in the world, producing approximately 833 Mt (918 million st) of raw coal in 2013. There were once more than 400 coal mines operating in the region. However, due to the combination of market conditions and implementation of government consolidation policies, the number of coal mines operating in recent years has been reduced considerably, with increasing output.The surface of the Ordos coal field is covered with loess and alluvium layers of varying thicknesses. In many areas, their combined thickness may amount to as much as 100 m (328 ft) underlain by thin bedrock. Many loess and alluvium are aquifers receiving water from rainfalls. There are also gullies of varying depths crossing the coal field. Figure 2 is a typical stratigraphic column highlighting the coal seams and roof and floor rocks of interest.In conjunction with the development of highproductivity coal mines, numerous ground control instrumentation tests have been conducted in the operating longwall panels. Analyses of the results of those tests offer the opportunity to understand the effect of wide-ranging mining and geological factors on the overburden movement. For this reason, trips were made to coal mines of interest to interview mine management and collect their unpublished internal research reports on ground control instrumentation. In addition, literature searches on published thesis/dissertations and papers in the professional journals were performed. Finally, data from a total of 95 fully mechanized longwall panels were collected. The instrumentation involved primarily the monitoring of hydraulic pressures of longwall shields, from which the first roof weighting and first roof caving interval and periodic roof weighting and periodic roof weighting interval were identified and determined. Some panels also included measurements of roofto- floor convergence at the face, roof strata bed separation, longwall face sloughage and the height of caving and fractured zones in the overburden. Those 95 panels were located in 20 coal mines (Fig. 1) congregated along both sides of the Wulunmulun River with the following mining and geological conditions. All together those 20 mines produced more than 224 Mt (246 million st) in 2013, accounting for approximately 27 percent of the total coal production in the Ordos coal field:1. Period of mining: 1991-2013.2. Mining methods: All panels employed the one slice, full-seam natural-caving longwall mining method like those practiced in the United States. All panels were developed with a twoentry system with a single-row of chain pillars measuring 20- x 20-m (65.6- x 98.4-ft) wide.3. Coal seams (Fig. 3): Coal in Ordos coal field is high-quality steam coal, that is very low in sulfur, potassium and ash, but high in Btu. Data were collected in panels mined in a total of 10 seams with 82 panels in four seams and the remaining 13 panels in six seams. The first six seams (1-2, 2-2, 3-1, 3-2, 4-2, 5-2) were mined by the Shenhua Coal Group (the world’s largest coal company) and the #4-2, 5-2, 6R, 62, and 62R seams were mined by both the Shenhua and Yitai Coal groups. In each coal group, the sequence of mining was in descending order. For example, in Shenhua Group, the top seam 1-2 was mined first, followed by the 2-2, 3-1, 3-2, and 4-2 seam in that descending order. In Fig. 3, the top-down sequence of coal seams is listed from left to right in each coal mine group. All seams were near horizontal with dip angles less than 3°."

Jan 1, 2014

By S. Rezaei

Moving ground in the mining industry is almost inevitable; however comprehensive awareness of these movements is necessary to mitigate risk. Monitoring of displacements caused by mining is a key tool for geomechanical risk management. Good monitoring may prevent unexpected failures and protect personnel and equipment. Many displacement monitoring techniques are available, however not all are reliable, accurate, and cost effective. Close range photogrammetry (CRP) is a monitoring method with high accuracy, reliability, and cost effectiveness; and has the ability to measure places that are inaccessible. In CRP, some series of photos are taken in different positions with different angles at different time intervals depending on the displacement rates. These photos are processed using PhotoModeler software and 3D models are made. By comparing 3D models, displacements can be measured. This method has been demonstrated at the Freeport-McMoRan Safford Mine in Arizona. A fault related instability in part of the pit is reactive to mining, and provided an opportunity to compare results between traditional monitoring methods and CRP. In this project, multiple series of photos were taken at different times using a Canon 5D Mark III digital camera, then PhotoModeler software used to make 3D models for each specific measurement event. Movement rates were determined by comparing different 3D models. These results are then compared to results of other monitoring methods to validate the CRP displacement method.

Feb 27, 2013

By Edward K. E. ] [Williams

Conditioning is any treatment of an ore with or without reagents which affect its floatability. While it can start in crushing or grinding circuits and continue into the flotation circuit, conditioning will refer here only to reagent treatment in an agitated tank designed for the purpose. Such treatment is often unnecessary with sulphide ores and collectors or with amines,* but it has long been recognized as essential with fatty acid collectors in the flotation of non-sulphide minerals, The requirements can be extremely variable, depending upon ore alteration, the presence or absence of slimes, and 1 the minerals to be separated. The study described here was concerned with the recovery of oxidized molybdenum minerals from an ore containing the element in both sulphide and oxidized form. Flotation of the iron minerals with which the oxidized molybdenum was associated was the basis for the process. Recovery and optimum concentrate grade without desliming depended upon a twenty to thirty minute conditioning of the pulp with flotation reagents at forty to fifty percent solids and at high turbulence. The objective in the study was the determination of design and operating criteria for conditioners in order to permit scaling-up of the results without repeating the entire study on a larger scale.

Jan 1, 1968

By K. Ohga

Japan has produced 14-16 million tons of coal per year in the past several years. About half of the production comes from eight coal mines in the Ishikari coal field, Hokkaido. Most of the gassy coal mines are in this field and the average mining depth of these coal mines has already attained about 700 m from the surface. Therefore, most of the coal mines have suffered from occurrences of coal and gas outbursts. To prevent outbursts and to reduce ventilation air, gas drainage has been carried out at all of these coal mines and these have had successful results. However, the methods of gas drainage differ from mine to mine. In this report, an outline of the main methods of gas drainage are described.

Jan 1, 1987

By Richard H. T. Garnett

In 1900, placer gold was discovered on the beach of Nome, AK on the southern coastline of Alaska's Seward Peninsula (Garnett, 1991). The site is about 800 km (500 miles) from Anchorage. Nome is connected to Anchorage only by air (daily) and by sea (summer). Total onshore placer gold production from Nome's immediate vicinity was more than 155.5 t (5 million oz). Alaska Gold Co, has continued to produce gold onshore with, until recently, two bucketladder dredges, each of 255-L (9-cu ft) bucket capacity. Small-scale marine dredging for gold has been at- tempted several times this century (Garnett, 1991). Western Gold Exploration and Mining Co. Ltd. Partnership (WestGold) is the only company to have been successful in achieving a significant offshore production. The Nome bucketladder-dredging operation from 1986 to 1990 constituted a unique marine-mining experience in the United States. \Inspiration Gold Inc., WestGold's predecessor, acquired six offshore leases in 1985. The total lease area of 87 km2 (21,551 acres) extended from the coastline to the 4.8-km (3-mile) offshore limit (Fig. 1). Those leases al- ready had been partially explored. Drilling was conducted off the shorefast winter sea ice. Therefore, it was rarely more than 1.6 km (1 mile) from the shore or in water deeper than about 9 m (30 ft). In 1985, estimated reserves comprised of a 5-m (17-ft) vertical thickness of sediments below 6.3 m (20 ft) of water. This meant a mean digging depth below the mean sea level (msl) of 11.3 m (37 ft). It was thought that the offshore Nome deposit possessed a feature that is common with many terrestrial gold placers - the secret of profitable exploitation of the marine deposit lay in maximizing the dredge throughput to minimize the unit costs. The inability of the project to withstand the prohibitively high cost of a new dredge was recognized. So Inspiration Gold purchased a used unit. This was the world's largest ocean- going bucketladder dredge (Fig. 2). Binzn was an 850-L (30 cu ft) bucket capacity dredge that was lying idle in Singapore. Originally constructed in the Jurong shipyard of Singapore in 1979, Bima was designed by Mining and Transport Engineering, a subsidiary of IHC Holland. Billiton Marine used the dredge for tin production at Pulau Tujuh in Indonesia (Dieperink, 1978) before it was laid up in mid-1985. Bima underwent a nine-week refit before departing Singapore on June 4,1986, with 800-t (880-st ) of deck cargo. It was dry-towed for 32 days to Alaska. A slower, less expensive, wet-tow at the authorized 5.5 kmthr (3 knots/hour) would have delayed the dredge's arrival in Alaska untl almost the onset of winter. The 13,000-km (8,100-mile) voyage was made on the deck of Smit Lloyd's "Giant-4" submersible barge towed by its 7.8- MW (10,500-hp) tugboat. The first season's dredging revealed several major shortcomings in Bima. Further repairs and modifications were undertaken at Tacoma, WA. The dredge returned to Nome for the June start of the 1987 summer dredging season. The refitted Bima worked offshore at Nome from 1987 to 1990. It produced 3.67 t (118,078 oz) of gold at an average recovered grade of 824 mg/m3 (0.0204 oz/cu yd). In 1991, the dredge was dismantled and sold.

Jan 1, 1997

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By Anuradha Khetwal, Tala Tahernia

The estimation of TBM utilization rate can be problematic due to the uncertainty involved in the tunneling system reaction to various geology along the tunnel. Moreover, the impact of operational and management issues on TBM performance is unsettled. This includes the occurrence and duration of downtimes and the uniqueness of projects relative to the geology, machine type, backup system, site setup, crew experience, and operational restrictions imposed on the project by localities. The CSM2020 is a model based on discrete event simulation that predicts machine utilization for single or double shield TBM. This model was developed by the Earth Mechanics Institute (EMI) team, using the database of tunneling activities which was compiled based on field observation and measurements in pertinent projects. In the current study, CSM2020 was modified to simulate the workflow of slurry TBMs. The operating principle of slurry shield TBMs is different than open-mode TBMs. The model was verified by comparing results with a recently completed project in the United States. As a result, the model offers reliable utilization rate estimation in different types of TBM by implementing appropriate workflow.

Dec 1, 2022

By Wm. I. Weisman

Sometimes in assessing where we are and where we are going it is informative to take a look at where we have been. Whether or not it adds to our understanding of the present, I think it may be interesting to review some of the past history of our industry. As a starting point I chose to use the famous Paley Commission Report, formally known as "The U. S. President's materials Policy Commission -Resources for Freedom."(l) The Paley Commission report said "Fluorspar is an essential raw material for the steel, aluminum, and chemical industries." Of course this statement is still true. It also said, "United States known reserves of fluorspar would be sufficient for some 15 years at present rates of consumption--about 426 000 short tons in 1960. Projected consumption for 1975, however, is several times as great, and reserves in other free countries do not appear adequate to supply United States deficiencies during the next 25 years." This simply demonstrates how even the most learned and competent people can observe all the facts avail-able to them at a given time and yet be unable to predict the future very accurately. We all know that reserves in other countries are more than adequate to supply the United States today, 25 years since the report was published. In fact, the report estimated free-world reserves at something over 36 million tonnes (40 million short tons). Contrast this with 246 million tonnes (271 million short tons) estimated as total world reserves from the section on fluorspar from Commodity Data Summaries of 1974, published by the Department of the Interior. (2) The Paley Report discusses other matters pertaining to fluorspar that are still of interest, such as improving mining methods. Furthermore, it certainly did a good forecasting job in noting that greater recycling should become possible in the aluminum industry in regard to fluorine lost in wastes and also concerning the substitution of fluorspar in the steel industry by other fluxing materials. It also suggested that non-fluorine containing propellants should be investigated as a replacement of those containing fluorine as a conservation matter. Some discussion was devoted to recovering the fluorine content of phosphate rock, which is being practiced today, but was in its infancy in 1950.

Jan 1, 1978

By DeVerle Harris

The enthusiasm with which individuals have participated in mineral exploration in the development of this country testifies to the fact that there was once a very real probability of making a worthwhile discovery. Over the years, the discovery and subsequent exploitation of the accessible ore deposits have made the finding of new deposits progressively more difficult. Present day mineral exploration has evolved from the lone prospector with the grubstaker behind him to a very costly and complex business, involving large sums of money and a staff of experts in the fields of exploration technology. Exploration today must be carried out on a large scale to be profitable. With the involvement of large amounts of capital, there has been a good deal of interest in methods of optimization of the allocation of the resources of a firm 'engaged in mineral exploration. As a step toward this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firms operations so as to optimize its profit objective or more simply, to make exploration more efficient and effective.

Jan 1, 1964

By Gabriel Babut, Ion Matei, Roland Moraru

Several controlled recirculation systems are in operation wor1dwide. As an unconventional technique of ventilation the implementation of such a system requires particular safety conditions and a well-founded set of feasibility factors and parameters. On the other hand, many mines in Romania are facing problemms in meeting the growing ventilation demands, so that controlled air recirculation could give an answer. The present paper presents the results of the work in this field, based on a detailed theoretical approach. Parameters wich must to be taken into account were identified and analysed, numerical simulation are carried out and an experimental test-scale model is presented.

Jan 1, 1997

By Gregg R. Bierei

Arch of Illinois is a mining complex comprised of two surface and two underground mines located in Perry County, in southern Illinois. The company a division of Apogee Coal Co. of St. Louis, MO. Arch of Illinois' two surface mines, the Captain and Horse Creek Mines, use large stripping shovels and cross-pit bucketwheel excavators to remove overburden from three seams of coal, the Herrin No. 6, Harrisburg No. 5 and Danville No. 7. All are considered high sulfur reserves. The two underground operations are managed by Arch of Illinois. They are the Kathleen Mine and the newly constructed Conant Mine, which began production in 1991. Both underground mines are continuous miner operations. They mine the No. 6 coal, which is about 1.8 m to 2.1 m (6 to 7 ft) thick. All coal is currently transported by truck to a central preparation plant located at the Captain Mine. This preparation plant produces 27 kt/d (30,000 stpd) of clean coal. Production in 1992 reached 5.9 Mt (6.5 million st) of saleable coal. Of that, about 66% or 4 Mt (4.4 million st) are produced by the surface mines and the rest the by under ground operations. Change is in the wind for Arch of Illinois. In 1988, 100% of all production (6.2 Mt or 6.9 million st) came from surface operations. By 1995, only 38% of production is scheduled from surface mines. And by the year 2000, 100% of production will from underground mining methods. Dwindling low ratio reserves, compounded by increasing environmental and land acquisition costs, coupled with more efficient underground mining equipment, have started an evolutionary trend toward development of underground reserves. For Arch of Illinois to maintain profitability of remaining surface reserves and to compete effectively mining underground, it must improve efficiency, productivity and cost reductions. These efforts are essential for maximizing current surface reserves and to ensure a continued existence in the presence of clean air legislation and the softening of the high sulfur coal market.

Jan 1, 1993

By Jin Dai, Xianwen Geng, Hao Liu, Pu Wang

To investigate how deformation failure occurs in roadways surrounding rock, the relationship between cohesion and plastic shear strain of the strain softening model and the equation for calculating the shear strain of a rock mass in the ultimate elastic state are derived. On this basis, the equality relationship between the built-in maximum shear strain increment and cohesion of FLAC 3D was established to give a more intuitive picture of how the cohesion of the roadway surrounding rock changes. The cohesion attenuation and deformation of the surrounding rock are analysed. The results show that significant deformation in the roadway surrounding rock was caused primarily by the development of large areas of highly softened plastic rock masses towards residual strength. Taking the floor overhead-mining roadway under different rock pillar thicknesses (RPTs) in the Xinglongzhuang Coal Mine as an example, the results demonstrate that investigating the cohesion distribution inside the roadway during mining operation can provide a more intuitive, more accurate description of the degree of failure of the surrounding rock at any point of the roadway, as well as the overall failure range of the surrounding rock. The simulation agrees well with the field monitoring result and seems to be more practically useful than simply analysing the coverage of shear plastic zones. Based on the failure range and degree of roadway surrounding rock with different RPTs, three support schemes are designed. Classified support was implemented for roadways under different RPTs, which realizes the effective control of roadway surrounding rock.

Jan 16, 2022

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020