Search Documents

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, NV began large-scale production in 1977. During 2008 Round Mountain Gold Corp. (RMGC) relocated the primary crusher facility approximately 300 m (1,000 ft) to make room for the next phase of openpit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket. RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17-m- (56-ft-) high mechanically-stabilized embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, CO. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design and construction of the MSE wall.

Jan 1, 2010

By T. A. Toney, L. R. Fish, P. J. Bethell

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers and recirculation have been attempted with some success. This paper reports on a novel (patent applied for) approach to retreating spiral middlings in a heavymedia cyclone circuit.

Jan 1, 2000

By F. Soumis

This paper describes an integrated procedure for the very short term production planning of an open pit and the execution of this plan: the truck dispatching. Integration of plan and dispatch means that the plan is realistic so that its objectives can be realized by the dispatch. This realism is obtained by supplying the plan optimization, which involves mixed integer programming, linear programming and non-linear programming, with experimental O.R. models of waiting and blending. The arrangement of these models in the computer programm has made it possible to obtain very short computing time for the planning in spite of the width of the optimisation. The dispatching of a truck is made by solving a classical assignment problem for each dispatch over a horizon of the expected*next 10-15 trucks to request dispatches. This deep-reaching dispatch procedure uses the continuously arriving information about trucks' positions and shovels situations and models by probability functions the expected waiting time of shovels and trucks. In this manner trucks and shovels are synchronized and last moments' opportunities for productivity gains can be obtained. The dispatch procedure takes .5 second on PDP11. This integrated planning and dispatch procedure gives high productivity while ensuring good blending. Results from the Mount Wright mine of the Quebec-Cartier Mining Co., where the integrated procedure has been installed on the existing computer equipment PDP11, are included.

Jan 1, 1989

By Lennart Mukka

This paper describes the experiences from construction of a new ventilation system in LKABs Kiruna Mine in Sweden as well as the choice of the method for air flow regulation with concern of life cycle cost and the description of the foundation design. The evaluation of the performance test will be presented.

Jan 1, 1997

By R. Kingman

At Tahawus, New York, National Lead Company operates the MacIntyre Development, This operation produces 10,600 long tons of ore per day for crushing, 8,000 tons for grinding and processing, of which 2,000 tons per day reports as tailing for disposal in an impounded tailing storage area. With the change in location of mining operations at the mine of National Lead Company, a change in the area for tailing disposal by gravity became necessary, This called for the diversion of tailing from near the proposed mining area to areas more favorable for long term storage by gravity. In order to avail the operation of maximum storage for the future, a uniform minimum grade launder was proposed with a minimum velocity and maximum outfall at the discharge. Disposal of the gravity and flotation tailing was formerly accomplished in open ditch from the concentrator at a grade of 1.5 percent. It was desirable to design the new launder at grades less than this for the greater storage elevation.

Jan 1, 1966

By Steve Kral

The dramatic rescue of nine Pennsylvania coal miners trapped nearly 90 m (300 ft) underground for77 hours probably would not have happened without the high technology equipment and improved mine rescue training techniques available today. By now, most everyone has heard the story of the accident that occurred at the Quecreek Mine near Somerset, PA. At about 9 pm on Wednesday, July 24, the miners were drilling coal in the room-and-pillar mine. Their drilling accidentally punched through to the adjacent, abandoned Saxman Mine. Old mine maps of the Saxman Mine led Black Wolf Coal, Quecreek’s owners, to believe they were between 60 to 90 m (200 to 300 m) away from the abandoned mine. Those maps proved to be inaccurate.

Jan 1, 2002

Introduction The frigid regions of Canada's high arctic islands are well-known for major oil and gas explorations. But mining leads the way in development. Cominco Ltd.'s Polaris mine is in its second full year of commercial production, and outstripping the rated production capacity foreseen by its planners. The Polaris mine is located on the shore of Little Cornwallis Island, near the settlement of Resolute Bay. The mine property is compact. It occupies about 3 km2 (0.5 sq miles) of the vast Arctic landscape. A number of mining and technological firsts were necessary to bring a mine into production at this 76° North latitude. Development constraints that had to be overcome included climate, remote location, and the limited ice-free shipping season. Construction of the entire process plant and ancillary facilities took place on a barge in the South where labor and supplies are plentiful. The plant was towed through ice-strewn waters to its permanent location at the mine site 1450 km (900 miles) from the North Pole. Freighters moved the first shipments to the South during ice break-up in late summer 1982. Most of the zinc concentrate is sold to European smelters. The remainder is tolled at a custom smelter in Europe, and the resulting metal is sold by Cominco. Lead concentrate is sold to European smelters. The mine was designed to produce 177 kt/a (195,000 stpy) of zinc concentrate and 41 kt/a (45,000 stpy) of lead concentrate. Actual production in 1983 was considerably greater, with both mill throughput and feed grades being higher than forecast. Production was 217 kt (239,300 st) of zinc concentrate and 51 kt (56,300 st) of lead concentrate. Average milling rate was 2.3 kt/d (2500 stpd), well above the designed capacity of 2.1 kt/d of (2300 stpd). Arctic Climate Extremes The climate is typical of the Arctic: very dry with short, cool summers and long, cold winters. From November through February, there is continuous darkness. Continuous daylight prevails from April to August. Precipitation is light, rivaling the Sahara desert at about 127 mm (5 in.) of rain and snow a year. An almost continual wind forms deep snow drifts against any obstacle on the ground. Temperatures range from a winter low of about -50°C (-58°F) to a relatively pleasant 15°C (59°F) during sunny days in August. Freeze-up begins in September and ice thickness increases from less than 0.3 m (1 ft) in early October to a maximum of about 2.1 m (7 ft) in May. The permanently frozen ground extends to a depth of about 427 m (1400 ft). Only a few inches of surface ground thaws in the summer. Exploration Activity Zinc-lead mineralization was

Jan 10, 1984

By Angelus S. C. Owili-Eger

The protection of groundwater resources is a growing issue on both the legislative front and within the private sector. At present, the legislative push is to establish within the Environmental Protection Agency a comprehensive research, development, and demonstration program relating to groundwater contamination and resources. It is evident that certain aspects of such legislation will be directed at the mining industry. Consequently, the mining industry must position itself to address the issues and concerns from a backdrop of facts and knowledge by developing an integrated hydrogeochemical model of the mining environment.

Jan 1, 1989

By Wi11iam I. Rau

In the recent past, there have been numerous projections of the capital requirements for additional mine and processing capacities required to meet projected non-Communist World demand for minerals during the next 15 years. A consensus judgment would place this currently at $14 billion per year, with the largest expenditures required for increases in aluminum and copper production. Until the early 1960's, internally-generated funds were used to finance nearly all of the large mining companies' capital requirements. Since that time, however, the enormous rise in capital costs per ton of capacity, accompanied by a relative stagnation in the financial condition of many of the major mining companies, have caused the industry to begin to rely on external sources for financing expansion, most notably, project financing from commercial banks and institutional lenders. Seven years ago, it was estimated that, in the five-year period 1972-1976,75% of the total capital requirements of $10 billion per year would come from internally-generated funds, with the balance to be provided by external sources. l There is little doubt that, in the coming decade, the percentage provided by external sources will increase. There should be little difficulty in attracting the necessary investment within the U.S., particularly in view of the expected continuation of companies in diverse industries seeking mineral investment opportunities. The more serious question lies in the availability of internal and external sources of funds for the expansion of mine and smelting capacity in the developing countries. Recently, R. F. Mikesell projected an average annual investment of $4.7 billion (in 1977 prices) over the 1977-1990 period would be required from foreign sources to expand metal producing capacity in developing countries. Mikesell concluded that external financing of mining projects in the developing world has averaged less than $1 billion per year over the past five years, thereby requiring more than a quadru1ling of this financing over the next decade.

Jan 1, 1978

By C. T. Twort

As technology and economic conditions allow mines to operate at ever greater depths, increasing demands are placed on the environmental engineer to adjust the capacity of the installed mine . - refrigeration systems. At the same time the engineer must satisfy the changing legislation, which demands that developments are carried out in as an energy efficient and environmentally accept- able manner. Following the trends outlined above, this paper is written to give an overview of the current and potential future refrigeration technology available to the mining industry. The effects that may be produced by the adoption in mining applications of the new generation of 'green' refrigerants are examined both at the design stage and when considering the viability of retrofitting existing systems so that they comply with the Montreal Protocol. An introduction to the concept of Total Energy Warming Impact (TEWI) is provided, with an explanation of its use in optimising system design and performance, and its incorporation as part of an environmental audit strategy. The paper concludes with a discussion of innovative refrigeration techniques and the possible future developments in legislation.

Jan 1, 1997

By Randal J. Barnes

Computer based techniques for solving the Ultimate Pit Limit Problem have appeared in mining literature since the early 1960's. The majority of papers pertaining to this subject can be partitioned into one of two categories: discussion of the pros and cons of a particular algorithm, or a case study presenting specific applications of an algorithm. Subsequently, there has a1 so been considerable debate concerning the best techniques between, essentially, two camps: those favoring the moving cones techniques, and those favoring the techniques which yield true optimal pit designs. The purpose of this paper is not to add to this debate, but rather to present a few new ideas (partially a new look at an old idea), which can be easily implemented to noticeably improve any ultimate pit limit approach independent of the particular algorithm used. These ideas fall under the heading of "bounding the optimum" (Barnes and Johnson, 1980).

Jan 1, 1982

By B. Howerton, M. M. Matlock, D. A. Atwood

In the Gold-Cyanide Process (GCP) the cyanide anions act to solubilize the gold and silver present in the ore, and mercury as well. The resulting mercury and cyanide rich effluent are serious health and environmental problems. Currently, there is no mercury treatment from the ore leach solution since there are no precipitating agents or other technologies which can be used effectively in the pH ~ 10solutions. Recently, however, we have developed a new chelate ligand that is impervious to this level of pH and it can be used to precipitate Hg from NaCN solutions. On an actual sample taken from an active gold mine the chelate selectively reduced the mercury level from 34.5 ppm to 0.008 ppm within 15 minutes. Importantly, the gold and silver levels remained unchanged throughout this process. Thus, the environmental impact of Hg released in the GCP can be drastically reduced. Moreover, with a mercury treatment technology now available it may be possible to change, or reinvent, the entire GCP process.

Jan 1, 2003

By A. M. Stone

Following the conceptual idea of a Continuous Elution Process early in 1982, the system was successfully pilot plant tested at Western Mining's Kambalda gold plant in December 1982. As a consequence of these tests the Ok Tedi elution ciruit design was changed from batch operation to continuous operation resulting in a reduction in the number of similarly sized elution columns from five operating with one standby to one operating with one standby and halving the process steam requirements. In addition to providing significant capital and operating cost savings the continuous process was simpler to operate than the batch process.

Jan 1, 1989

By James C. Franklin

Companies are constantly searching for more effective methods of controlling and reducing costs. In recent years increased emphasis has been placed on cost reporting to the middle manager and down to the first-line foreman because this is the place where the money is really spent. Traditionally, operations management has been relegated to using cost systems designed by financial management for the use of financial management. They reflect the machinery necessary to produce profit and loss statements, and so-called cost reports emanating from these systems frequently have a heavy orientation toward product costing rather than the cost that an individual manager or foreman actually controls. In addition to direct operating costs by function or product type, they often include overhead allocations from local operations as well as from the home office. This type of full-absorption costing has many worthwhile uses but is of little or no use to operations management for cost control purposes. It is particularly discouraging to many supervisors because it includes so many categories of cost over which they have little or no control. It is for this reason that modern, aggressively managed companies are increasingly moving in the direction of responsibility cost reporting. It is the objective of responsibility cost reporting to report only direct operating costs over which the individual manager or foreman has complete control, thus facilitating cost control by fixing responsibility for cost.

Jan 1, 1979

By Pasi Latva-Pukkila

Underground rock drilling has gone through intense development during the last 25 years. Mechanization and hydraulics have greatly increased the efficiency of drilling and improved the environment of the drill operator. As the total economy has become more and more important, the development has resulted in greater overall economy in drilling. The latest evolution step is computerization of drilling equipment. Computerization has been applied to tunnelling jumbos, long- hole drilling rigs and bolting rigs. With today's technology computerization is the natural way to increase capacity and productivity of the drilling process. However, it is still impractical to implement total "robotic" drilling. In computerized drilling the operator's role continues to be vital in controlling the drilling process and in analyzing the effect of individual parameters on the whole excavation process. Today this is called "CAD" - Computer Aided Drilling.

Jan 1, 1989

The more than 40,000 mining industry professionals that are expected to attend the National Mining Association’s(NMA) MINExpo International2000 trade show and conference will be treated to the exhibition’s largest display ever. The exhibit is expected to cover more than 60,385 m2(650,000 sq ft) and feature more than 1,300 exhibitors. The event is set for Oct. 9-12, 2000 at the Las Vegas Convention Center in Las Vegas, NV. Richard L. Lawson, NMA’s president and chief executive officer, said, “MINExpo 2000 will showcase everything that mining is proudest of. This is the largest premier mining exposition in the world.” MINExpo is held every four years.

Jan 1, 2000

By F. Habashi

Asbestos, an extremely useful natural resource, has been studied extensively mineralogically and for industrial application. Its extraction from ores has been greatly improved with respect to safety in the work place. In spite of that, there is a decisive effort in many countries to ban its use on the grounds that it is a toxic substance. This action resulting in drastic decrease in production and the possibility of destroying the industry. The chelation of asbestos with organic dyes seems to be a promising way to abate its toxicity. Dyeing can be done when the fibers are slurred in water at ambient conditions in the same way as textile fibers.

Jan 1, 2009

By I. Edgar Odom

Hectorite is a rare magnesium-lithium clay mineral that occurs at many places in the McDermitt caldera of Nevada-Oregon. Commercial development of several high purity deposits began in 1986. The hectorite that was precipitated in a lake environment formed after the collapse of the McDermitt caldera. Hectorite beds and lenses are associated with volcanic sediments, limestones, dolomites, zeolites and locally sandy bentonites. The high purity deposits appear to be associated with hydrothermal areas. The hectorite consists of extremely small, flake-shaped crystals. Calcium (Ca) is the predominant exchangeable ion. Its color ranges from white to light green. Commercial uses include high-brightness, magnesium-aluminum-silicate (MAS) products, organophilic clays, pulp retention and ceramics. The MAS is used as a suspending agent, binder, stabilizer and thixotrope in aqueous solutions for cosmetics, household cleaners, pharmaceuticals and miscellaneous industrial applications. Hectorite-based organophilic clays are used in printing inks and paints. The McDermitt caldera complex is located astride the Nevada-Oregon boundary west of the town of McDermitt, NV (Fig. 1). The structural complex is elliptical in shape, extending about 43 km (27 miles) north-south and 34 km (21 miles) east-west. This area was the site of extensive volcanism during the Miocene (24 to 18 million years). The complex consists of five overlapping calderas with the oldest at the south end of the complex (Rytuba et al., 1979). Each of the vent areas collapsed and is marked by a ring fracture zone. The ring fractures around the outer boundary of the caldera complex are shown in [Fig.1].

Jan 1, 1992

By E. D. Thompson, Y. J. Zhang, K. F. Unrug

This paper presents the results of a recent study on the development of an in situ testing method for determining coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using a penetrometer, which is an hydraulically powered device that uses an indenter to press on the surface of the borehole until the load reaches the failure point of the coal. The pressure and the penetration of the loading pin are recorded by a data-acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of the pillar-strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1997

By Randal J. Barnes

There are many methods available for the estimation of geologic parameters (Popoff, 1966; Barnes, 1980). In the last decade a new and relatively sophisticated technique using statistical theory has emerged: geostatistical kriging (David, 1977; Journal and Huijbregts, 1978; Rendu, 1978). An interesting property of geostatistical estimation is that when a geologic parameter is estimated for a given volume, not only is the estimate generated but an associated measure of certainty is produced as well. This statistical measure of estimation confidence is called the estimation variance. While the concept of an estimation variance is universally considered to be a good idea, mining engineers and geologists do not currently have the tools to incorporate it into their planning and quantitative analysis. This paper attempts to develop and present some of the necessary tools required to incorporate estimation uncertainty into mine planning. Geologic uncertainty is portrayed as an economic business risk. This risk is objectively characterized, and-the associated cost is quantified. Geologic delineation sampling is viewed in this light as an economic commodity with an associated cost and value. A coal mine planning example is used as a focus in this presentation. The data used is real, though it has been modified to maintain data security and project anonymity.

Jan 1, 1986