Search Documents

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By S. Chatterjee, A. K. Gorai, Sahendra Ram, Kapil Kumar, J. Anil

Extraction of underground coal or mineral by the caving methods leads to surface deformations and the accurate measurement of this deformation is becoming a demanding task. Thus, the study demonstrates a Persistent Scatterer Interferometric Synthetic Aperture Radar (PS-InSAR) technique for surface subsidence measurement. The method was applied to measure the subsidence level over three mechanized depillaring panels with caving at GDK-11 Incline mine, India. The study was conducted using C-band data of Sentinel 1A/B sensors, which captured the data in the descending path from October 25, 2017 to March 07, 2020. The deformation level was measured based on the identified PS points in the specified region. In this case, 12 zones were identified (4 for each panel), based on the observation of permanent scatterer (PS) points. The maximum subsidence level and deformation rate range in 12 zones are −43.12 to −65 mm and −73.8 to 100 mm/year, respectively. The deformation level obtained through the PS-InSAR technique showed a good agreement with those of the field measurement. Thus, the PS-InSAR technique can detect and monitor the subsidence level over the goaved-out panel(s) of an underground mine using C-band SAR data of the Sentinal-1A/B sensor.

Mar 14, 2023

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023

By B. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformations. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, time-lapse point clouds of mine workings. In order to determine sloughage volumes and locations, a total of 11 laser scans were performed 41 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds.

Feb 27, 2013

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By K. A. McDonald

This paper will describe the experiences of Hibernia Holdings, Inc. in constructing a mineral processing facility in Mexico. It will attempt to set forth a guideline on what companies attempting to operate in Mexico can expect and what actions they can take. Ownership laws, import/export laws, labor laws, security, transportation and operating experiences will be discussed.

Jan 1, 1994

By M. Deutsch

A common casualty of modern open pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can really be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period. And grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper all of these problems are addressed by encoding these three fundamental open pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot. INTRODUCTION Open pit mines are large and complicated operations, which require significant initial and ongoing investment. A single mine may employ hundreds or thousands of people and creates substantial benefits for both the surrounding and global communities. Planning an operation of this magnitude requires a lot of effort and cannot be done optimally by hand. Mining engineers today rely on many techniques from operations research to guide decision making, and to maximize the value of the mine. Techniques including linear programming, metaheuristics, and network algorithms are all used to solve different problems throughout mine design and optimization. However, techniques based on Boolean satisfiability, including the optimization extension of maximum satisfiability, have not seen much use in mining despite being used in many other fields including electronics design, scheduling, and artificial intelligence. We claim that maximum satisfiability is a useful and meaningful way of expressing and solving optimization problems in mine planning. However, this technique does not come without challenges; the problem is NP-hard, and modern techniques for solving these problems can struggle with the number of variables and clauses that a typical mining problem requires. Also, some of the constraints that mining must contend with do not fit nicely into the satisfiability paradigm. Despite these challenges, we believe that maximum satisfiability provides a useful framework for considering operational constraints and expressing some problems that other techniques can't easily express. Maximum satisfiability can be solved exactly, yielding the true optimal answer which metaheuristics cannot guarantee. In this paper we show the applicability of maximum satisfiability to mining by specifying three fundamental problems in open pit mine optimization. We show how these fundamental problems can be formulated and how they can be extended within the framework of maximum satisfiability. For the remainder of the paper we first give a brief background on common elements between the three problems and an introduction to satisfiability. Then we tackle the three problems; the Ultimate Pit Problem, the Block Scheduling Problem, and the Grade Control Polygon Problem. In the Ultimate Pit Problem we specifically show how to extend the problem to support a minimum mining width – a coveted result for many mining engineers. We then discuss some of the complexities and shortcomings of this framework and possible research directions.

Jan 1, 2019

By John P. Anderle

A tectonically disturbed sequence of Mississippian age evaporites expressing a 5 milligal negative gravity anomaly near Sussex in southeastern New Brunswick, Canada, was investigated by a program of drilling, geologic and geophysical work over the past 27 months. Seventeen of twenty-one drill holes have penetrated 10 to 140 feet of potash mineralization in a salt sequence underlying 2 000 to 3 000 feet of arenaceous, conformable red beds, also of Mississippian age. Bromine and borate studies, lithological characteristics and geophysics, have facilitated improved understanding of the salt structure. The salt sequence has been affected by f1owage which has resulted in both major and minor folding. In the more disturbed areas, the potash interval was extensively subterraneally eroded at the upper anhydrite-salt contact.

Jan 1, 1978

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By N. T. Mirafuente

The device called "Dynastat" which is described in this paper provides in situ borehole measurements of dynamic and static parameters for use in a wide range of design applications. In the dynamic mode, the Oynastat allows measurement of shear and compressional wave velocities. From these velocities in situ dynamic Young's modulus and other dynamic elastic parameters can be calculated. In the static mode, the device allows measurement of load versus deformation from which in situ static Young's modulus can be determined. Information on in situ horizontal stress fields can also be estimated from the load deformation curves. In both mining and civil engineering applications, in situ measurements of material properties are indispensable for accurate evaluation of design problems. Laboratory dynamic and static test measurements in comparison to in situ measurements are often misleading due to difficulties in obtaining undisturbed samples and in accounting for effects of discontinuities, etc., for mass properties. The authors contend that among in situ borehole measurements, the method employed with the Dynastat is the most accurate and detailed technique of measurement. The Dynastat employs the crosshole method of shear and compressional wave velocity measurements and also performs as a borehole jack to obtain load-deformation relationships of materials at exactly the same location at depth in boreholes.

Jan 1, 1976

By Moussa Wone, Martino Scialpi, Colin LaVassar, Carlton Ray

The Potomac River Tunnel (PRT) is the next major phase of the DC Clean Rivers Program. The design-build PRT project includes a 5.5-mile-long, 18-foot-internaldiameter tunnel, seven shafts, and two underground connections to existing structures. Major challenges include tunnel boring machine (TBM) excavation though mixed-face conditions within a buried paleo-channel and an approximately 1,350-foot-long rock/ soil transition zone; construction beneath the elevated Whitehurst Freeway; tunneling beneath an existing luxury residential building and existing transit tunnels with limited clearance; and complex coordination with a variety of federal, regional, and local stakeholders. This paper describes the overall project scope, geotechnical conditions along the alignment, and primary design/construction challenges and mitigations.

Jun 13, 2021

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various' shapes in sound rock.

Jan 1, 1967

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965

By Deborah Shields

Aggregate is an essential input to every economy, so governments need to ensure a sustainable supply of these resources through planning. There is also a need to shift from a linear economy to a more circular one, in which wastes are recycled rather than landfilled, so as to increase eco-efficiency. The purpose of the Sustainable Aggregates Planning in South East Europe (SNAP-SEE, SEE/D/0167/2.4/X) project is to develop a Toolbox for Aggregates Planning to assist governments and stakeholders in national, regional, primary and secondary, aggregates planning in southeast European countries. The Toolbox comprises documents on stakeholder consultation, data and analysis methodologies, a vision of best practices in aggregates planning and how to build an aggregates plan. The Toolbox will also support ongoing efforts to enhance minerals policy in the European Union (EU) as called for by the European Innovation Partnership on Raw Materials. Industrialized and developing nations see long-term and continued economic growth as essential to the well-being

By H. L. Bourne

The sand dunes which line the east shore of Lake Michigan resulted after the last, or Wisconsin, glacial period in Michigan. Melt-water streams carried vast quantities of glacial debris to the near shore areas of predecessors to Lake Michigan. As the lake levels receded, these vast quantities of sand were exposed to the prevailing westerly winds, which was the last major process that acted upon the sand and resulted in the formation of the dunes. 1 These dunes are one of the significant natural resources within the state. Michigan dune sands supply about 90% of the foundry sand used in the automotive industry, and 40% of the foundry sand used 2 for all purposes within the United States. The deposits owe their importance to the following factors: grain size distribution, grain shape, mineral composition and location with respect to the foundry sand market. In spite of their economic significance these I deposits are in jeopardy through legislative preemption.

Jan 1, 1975

By A. T. Yu

A recent analysis completed by the United States Department of Commerce predicts that the 1968 Gross National Product will reach a record high of 864 billion dollars. As our nation annually increases its total output of goods and services, as has been the trend, the consumption of steel and its most basic raw material - iron ore - also must increase, To deliver the most economical unit of iron ore to the blast furnace, each segment of the transportation system must be co-ordinated and utilized to its highest degree of efficiency. In some cases, such as with the water segment of the system, a new investment in capacity will be required.

Jan 1, 1968

By R. M. Tyson

Sulfides present in the troctolitic and footwall rocks are placed into one of three major zones (hornfels, cloud, and basal) on the basis of their stratigraphic position and mineralogy. Hornfels sulfides, enriched in Fe, represent remobilized sedimentary sulfide. Sulfides from the Cloud Zone are probably magmatic and are enriched in PGE, Cu, Ni, and Ag. The basal sulfides, composing most of the ore, resulted from contamination of the magma by remobilized sedimentary sulfide. The basal sulfides exhibit a differentiation trend in their mineralogy and chemistry. PGE, Cu, and Ag are enriched with increasing differentiation which is attributed to fractionation within an immiscible sulfide liquid.

Jan 1, 1986

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974