Search Documents

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

A glance at the following chart reveals that because of the continued poor economy, the slump in industrial mineral production continued into 1980. Gypsum was down 17% from 1979; cement down 9%, sand and gravel, 17%, and crushed stone, 11%. All these downward trends reflect the high interest rates and high costs that slowed construction starts. Domestic fluorspar was down 21% and imports off 14% due to the steel iudustry slump. However, potash production was up 8% and phosphate, 5%. Increased drilling activity spurred au increase in barite production of 25%. Most other industrial minerals posted losses with only a few insignificant increases. As expected, prices were higher, reflecting increases due to high costs for labor, supplies, and above all, energy. Increasing energy and transportation costs also had their effect on industrial mineral production. Railroad freight rates increased 16-22% including fuel surcharge; truck rates increased 11-14%a; and ocean freight rates increased 20% for finished goods. The 1979 shortage of boa and hopper cars did not continue into 1980-most likely due to low production of many of the hulk industrial mineral commodities. All in all, 1980 was not a good Year for industrial minerals.

Jan 5, 1981

By Xun Zhang, Hang Qiu, Andrea R. Gerson4, Shaomin Lei, Yubiao Li, Yu Meng, Zhenyu Pei, Min Lin

Efficient separation of trace muscovite from the surface/interface of quartz grains was accomplished during oxidizing calcination and catalytic pressure leaching of the hydrothermal quartz. Experimental results suggest that 98.97% or more of the muscovite was separated when quartz sand was calcined at 900 °C for 5 h and then leached by hydrochloric acid and ammonium chloride solutions as substitutes for leaching agents containing fluorides. The chemical processing techniques show high selectivity in purifying quartz sand by transforming mineral muscovite into active structures during oxidizing calcination, and then dissolving the active substances during catalytic pressure leaching

By D. C. McLean

Early studies in the carbonate leaching of uranium ores led to the investigation of pressure leaching as a method to enhance the dissolution of the metal values in this system. The initial investigations conducted at the University of British Columbia supplemented by the work done by the group at the A.E.C. Grand Junction pilot plant, all established the higher efficiency and better economics of the alkaline pressure leaching system. This work was conducted either in laboratory autoclaves using oxygen overpressures, or in pilot plant sized horizontal autoclaves with air as an oxidant. Both of these testing vehicles utilized agitation provided by relatively high speed impellers (300 to 700 rpm), which apparently enhanced the oxidation of the uranium to the hexavalent state. The installation of vertical autoclaves on a production scale, which through design considerations require relatively slow agitator speeds (68 rpm), led to the studies of the utilization efficiency of the air addition and the use of catalytic type oxidants to effect a greater usage of the oxygen added through the aeration system. In addition to investigating the effects of the chemical additives, studies were also conducted on the effect of different impeller configurations on the extraction of uranium, which in itself is a measure of oxidation efficiency. The material presented in this paper was compiled in the Ambrosia Lake district of New Mexico, and the majority of the data was obtained in the Homestake- Sapin Partners mill, located at Grants, New Mexico.

Jan 1, 1960

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

By S. K. Kawatra, H. J. Haselhuhn

"Thickening is used during two primary mineral processing operations: water removal and desliming. During water removal, the pulp density is increased through the injection of flocculants. These flocs settle and create a dense pulp while clarified water is removed through the overflow. During desliming, fine particles are removed through the overflow. Desliming can also be used as a mineral separation process known as selective flocculation-dispersion, where valuable minerals are flocculated and gangue minerals remain dispersed and exit through the overflow.There are many ways to analyze thickener performance on a laboratory scale, but these analyses often do not correlate well with full-scale performance. Some pilot-scale systems have been designed using a semicontinuous approach, but the amount of material required to perform their tests can make semicontinuous pilot thickeners impractical for most applications. This paper focuses on the design and optimization of a continuous pilot-scale deslime thickener that requires minimal material to operate. The design, optimization strategy, and an example study of reagent selection are demonstrated. IntroductionMany laboratory methods have been employed to size and optimize thickener performance. The most common of these include the Coe and Clevenger method and methods derived from the Kynch theory of sedimentation. The Coe and Clevenger method was developed in 1916 and was proven for slurries that do not require flocculation to settle. This method proposed that the settling rate of the pulp is only a function of the solids concentration. It is executed by creating slurries of several different concentrations of solids and performing bench-scale settling tests in graduated cylinders. For each concentration, a thickener unit area can be determined using the following equation (Coe and Clevenger, 1916; Laros, Slottee and Baczek, 2002):"

Jan 1, 2017

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022

By Paweł Stefaniak, Natalia Duda-Mróz, Sergii Anufriiev, Wioletta Koperska

Due to the high environmental risks and negative impact of a failure, tailings storage facilities (TSFs) need constant monitoring. Advanced mathematical models have been developed in the past to predict the behavior of TSFs and raise alerts if needed. To be precise and reliable, such models need a spatial distribution of soil types within the dam as an input. Getting this data from laboratory measurements is time and costconsuming. In this article, we propose an ANN-powered algorithm, which allows us to accurately estimate the soil distribution based on a cone penetration test (CPT).

Jun 25, 2023

By D. F. Lillie

The milling plant of Bicroft Uranium Mines Limited has been in operation for a period of 2 years. During this time many changes, both physical and chemical, have been made in an effort to improve plant efficiency. Investigational work has been facilitated greatly by the fact that the Bicroft mill consists to a large extent of two parallel circuits; however, the number of inter-related variables is great, and it is difficult to measure, let alone control, all of them simultaneously. The Bicroft mill staff feel that much progress has been made, but there is much yet to be done and many questions still to be answered. The property of Bicroft Uranium Mines is located in Cardiff Township in the Highlands of Haliburton County, southeastern Ontario, some 140 miles northeast of the city of Toronto and 70 miles due north of Lake Ontario. The ore-bearing dikes are classed as mafic, non-segregated, syenite and granite pegmatites. Microline, microline perthite, quartz, uraninite, uranotharite, fluorite, titanite, cyrolite, calcite, pyrite, pyrrhotite and molybdenite as important accessories. The mill was designed for a nominal capacity of 1,000 tpd with all sections except grinding, leaching and clarification capable of 1,500 tons. Feed was entered to one mill unit on October 29, 1956 and to the second parallel line on November 13. The total feed rate was at 1,000 tpd on November 15. The first precipitate was produced on November 12. By August 1958 the average entry had been increased to 1,410 tpd without the installation of any additional major equipment. The overall recovery has been greater than 93,0 pet do several months, but a recovery of 92.5 pct appears to be most economical. Operating time for 8 months in 1958 has been 97.1 pet although all grinding mills were relined during this period.

Jan 1, 1959

By D. Randall Crooke, Ron R. Jorgenson

Many coal combustion products (CCPs) have historically been unsuitable for placement as mine backfill because of their physical and geochemical properties and/or regulatory status. However, innovations in paste production and transport of CCPs utilizing the high, fine particle contents of these fine-grained waste materials and their water retention colloidal properties produce a non-segregating, self-cementing material that may be environmentally suitable for placement as mine backfill. Both industry and the regulatory agencies are enthused by the possible cost reductions, both in design and construction of disposal sites, and the reduced environmental impacts of CCP realized by implementation of this new use/disposal technology.

Jan 1, 2001

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By Franklin J. Stermole

L. Alan Weakly, member SME, is a senior staff engineer, Exxon Co. Weakly chaired a Mining Engineering committee formed to solicit materials for six planned "personal skills" articles, to be used in ME this year. What follows are Weakly's introductory comments to the series. Upon graduation from college several years ago, I thought that I was sufficiently prepared to embark in my chosen profession. A short time later I realized that several years of on-the-job training was going to be required before I could use my technical training effectively. It never occurred to me that, professionally, I was seriously lacking in any other skills. My spelling could use a little upgrading, but this was not a serious deficiency. I have been very fortunate to have had two employers that recognized that their engineering professionals did lack other skills and made every effort to give them training to correct these deficiencies. The skills I am referring to are those in administration and interpersonal relationships. Most mining engineers and geologists receive very little, if any, college training in these areas. In addition, many companies do not provide this training and many mining engineers and geologists are unaware of their deficiencies. It is for this reason the subject of personal skills development is being introduced in Mining Engineering. The mining engineer or geologist can pursue one of two basic career directions, managerial or technical. In today's technically sophisticated society and highly competitive business climate, both orientations require administrative and interpersonal skills. Most of us are technically qualified and we continue to upgrade our technical skills. But many studies indicate that we, as a group, are significantly weaker in administrative and interpersonal skills than other professional groups. In addition, these studies indicate that engineers, in general, take longer to reach managerial levels and fewer do so. This series in Mining Engineering, then, should help readers strengthen and broaden their professional capabilities. In all industries, including mining and petroleum, economic analysis of potential investment projects is done to select the projects that will give maximum future value from the investment of available capital. Rather than looking directly at the future values to be generated by investing capital in alternate ways for economic decisions, evaluators usually use either rate of return, present value, annual value, a profit to investment ratio, or various break even analysis results to reach economic analysis decisions in evaluating alternative investments. Alternative economic evaluation techniques are used in industry to properly analyze the economic potential of various investment projects. "Discounted Cash Flow" analysis is the phrase commonly used to describe these techniques. Whether you want to analyze projects in mineral, petroleum, real estate, refining, pipe-line transportation, or any other industry, proper application of discounted cash flow analysis techniques enables you to fairly compare the economic potential of alternative projects as well or better than you can using any other project evaluation approaches. It should be pointed out that investment analysis generally involves more than economic analysis. Financial and intangible considerations sometimes are as important or more important to investment decision-making than economic considerations. Economic analysis refers to evaluation of the profit generating potential of projects, that is selecting which alternative projects will generate maximum future value possible from available investment capital. Financial analysis, on the other hand, relates to analysis of where money is going to come from to finance various projects. Regardless of the economic potential of a project, if financial analysis indicates that we cannot finance the project, it likely will be shelved for financial reasons even though it may be economically satisfactory. Many evaluators use the terms "economic analysis" and "financial analysis" interchangeably, but this author considers that to be undesirable. Intangible analysis relates to project factors that are difficult to quantify in

Jan 2, 1984

By T. Rockley, B. Goertz, S. McDaniel, J. Brune, K. Bakhsh

"Researchers at the Colorado School of Mines, under a project funded by the Alpha Foundation, have developed a working prototype of a dust sample collection device designed to determine if sufficient rock dust has been placed in an underground coal mine to prevent coal dust explosions. When used in conjunction with the Coal Dust Explosibility Meter (CDEM), the device will provide near instantaneous results on the quality of rock dusting at the tested location. The sampling device applies a pulse of air to a testing surface and collect a representative sample of mine dust based on the pneumatic entrainment process during a mine explosion. The use of both physical testing and Computational Fluid Dynamics (CFD) modeling has allowed researchers to refine the design to accurately represent the particle entrainment and optimize the sample size collected for the CDEM. The prototype is being tested in a mine environment to produce information of usability and practical aspects of mine dust sampling. This paper is a progress report summarizing the current status of sampler development. Researchers expect to have a fully developed and tested sampler in early 2016. INTRODUCTION Underground coal mines face the danger of methane and coal dust explosions. The disaster at Upper Big Branch mine (2010) has demonstrated the impact of a violent coal dust explosion that fatally injured 29 miners. Reviewing the history of coal dust explosions, researchers found that that mine operators and mine inspectors do not have a reliable method of collecting dust samples to assure that sufficient amounts of rock dust have been places to inertize the coal dust. This is a problem specifically with small mines that do not have dedicated safety departments to track rock dusting work. The aim of this research is to develop a simple, portable device that can help underground mine examiners collect dust samples from workings and test the explosibility of the sample near instantaneously. Researchers determined that the current brush-and-pan sampling method required by MSHA (MSHA 2013) is flawed in several aspects: Mechanical sampling with a brush exerts forces on the mine dust that may differ significantly from those present during an explosion. Also, U.S Bureau of Mines research (Nagy 1965) has determined that only the top 0.125 inches of the mine dust layer will be entrained in a coal dust explosion. Using a handheld pan and brush, it is difficult to correctly and repeatably sample a layer of this exact thickness. The following will describe the CFD modeling and experimental testing for the development of the prototype sampler. Researchers analyze the accuracy and performance of the prototype during the course of the build process."

Jan 1, 2015

By J. K. Ahlness

The Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 225 ft (69 m) were tested at an average rate of four wells per 8-h shift with a two-person operating crew. This represents a 75-pct time savings and an 83-pct labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1986

By R. Abel, T. Wildeman, N. Heflin

A study was conducted to assess environmental effects of waste rock piles on water in the Russell Gulch area. Each pile was rated on physical characteristics of proximity to an ephemeral gulch, extensiveness of erosion features, size, presence of vegetation, and presence of a kill zone. Chemical assessments focused on three leachate tests performed on waste rock samples. Ratings were based on pH, conductivity, acidity, and analysis for 31 metals using inductively coupled plasma emission spectroscopy. The chemical and physical assessment of each site is used to make a rating of each pile on its overall potential to deliver contaminants.

Jan 1, 2004

By E. Watkins, M. B. Daza

Although there have been great advances regarding the understanding of mine fires in underground mines in the last century, fires remain high risk incidents. During fire scenarios, many crucial decisions and actions can be made that greatly influence the outcomes of these scenarios. Underground worker decisions are mainly based on training and experience, which in some cases can be complemented with previous analysis of fire effects. In order to review the guidelines that should be taken into account for this kind of examination, a numerical analysis of effects produced by a shuttle car fire under five different ventilation conditions was carried out. The analysis provides some insightful recommendations for firefighting personnel such as time for direct attack and best attack position for first responders and fire brigade groups. Also, the most critical parameters for each scenario were determined. Finally, all results were systematically organized and a first approximation of a fire classification based on the tenability limits was provided for first responder and fire brigade groups. The methodology used in this study for the fire classification could allow for the most appropriate decisions by firefighting personnel increasing the probability to put fires out without compromising their health and safety. INTRODUCTION While there have been great advances regarding the causes of mine fires in underground mines in the last century “small fires have occurred and always will occur in underground mines” (Conti, Chasko, Wiehagen, & Lazzara, 2005). The response time and decisions made during an underground mine fire are critical elements that have direct influence on the event outcome. Mine fires can grow in size quickly causing catastrophic consequences, thus rapid and suitable response actions can result in the difference between an minor emergency situation and a disaster. Upon the confirmation of a fire, a decision must be made regarding whether to fight the fire or evacuate the mine. Even though all underground coal mines possess emergency response plans and firefighting personnel are highly trained, decisions can be complemented with previous numerical analyses. Such analyses could contribute with the knowledge of potential fire effects and consequently with fire preparedness in the mine. Preparedness in underground mines is an important element to reduce the probability of the negative consequences of a mine fire. The time elapsed between the detection of the fire and response in the early stage is a serious component since small fires can produce larger and more serious consequences. If a mine fire cannot be put out within the short time after discovery, the chance of getting the system back in balanced or the success of safely controlling and extinguishing a mine fire is reduced (Conti et al., 2005, Conti, Chasko, Wiehagen, & Lazzara, 2000, Trevits, Yuan, Teacoach, Valoski, & Urosek, 2009, Brake, 2013). As confirmed by Conti and others, if a mine fire cannot be controlled by direct firefighting methods the probability of extinguishing the fire, without sealing is greatly reduced (Conti et al., 2005). However, response actions such as direct extinguishment must be carried out without compromising the health and safety of the firefighting personnel (Kim, Lönnermark, & Ingason, 2010).

Jan 1, 2019

By James J. Fallon

Last summer Larry Miller of Roberts & Schaefer told me that his AIME committee would like me to present some thoughts on the marketing of industrial mineral fillers and pigments to this illustrious group in Las Vegas. Shortly after, Brian Coupe of "Industrial Minerals" (the magazine) notified me that I would be presenting a paper to the Fourth International Industrial Minerals Congress in Atlanta this June. It seems to me now it might have been more appropriate to reverse the papers. Las Vegas, a town based on risk, might want to hear what we have to say in Atlanta. The subject for June is "Risk Philosophies of U. S. Industrial Minerals Companies". However, upon reflection, marketing of industrial minerals reflects risk philosophies to a considerable extent, so we'll cut the deck and deal on the subject of marketing.

Jan 1, 1980

By Derrick Chambers, George Kevin Chapin, M. Shawn Boltz

Seismic monitoring is one of the few noninvasive technologies with the potential to provide sub-surface geomechanical information to operators of large open-pit mines. Although passive seismic data has been used to refine emerging failure geometries and provide advance indication of surface deformations in the literature, doing so reliably in an operational context is much more difficult. This is due in part to difficulties in estimating and interpreting source locations and parameters in complex, low-stress open-pit environments. Additionally, the high costs associated with implementing, operating, and maintaining deep borehole seismic networks, which are most commonly used to monitor large open pits, can be difficult to justify, especially if monitoring benefits are not readily apparent. In this study, we explore the use of a near-surface nodal seismic deployment, which is commonly used in oil and gas exploration, for monitoring open-pit mining-related seismicity on a short-term basis. A deployment of 18 geophones was conducted on the surface in and around the Bingham Canyon Mine, a large open-pit mine near Salt Lake City, Utah, USA, where we find the small seismic array can detect and locate a variety of mining-related seismic sources, even with an extremely simplified velocity model. We outline the process of creating an idealized velocity model, developing a local magnitude scale, and interpreting the observed seismicity. Of note, we analyze a sequence of mining-induced events associated with a known structure on the south pit wall. We conclude with discussion on how surface-based deployments may be used to augment, or in some cases supplant, borehole seismic networks at large open-pit mines depending on monitoring requirements and objectives.

Apr 26, 2022

By R. T. Swinderman

"Virtually every article you read on safety has a statement to the effect: “It’s obvious that safety pays”. If it is so obvious, why is it so hard to answer these questions? • How does the Maintenance or Operations Manager convince the Plant Manager to spend money from the annual budget for safety improvements? • How does the Plant Manager influence Corporate to prioritize safety improvements? • How does an engineering firm persuade the owner to spend more on design and equipment up front to reduce risk? There are many cultural and structural reasons why it is so difficult to prove the obvious. In my opinion the main culprits are: the almost universally used ‘Low Bid’ process, variations in reporting incident statistics between industries and countries, and, the Generally Accepted Accounting procedures (GAAP) [or International Financial Reporting Standards (IFRS)]. Conventional wisdom is it’s smart not to spend more than you need to meet the minimum regulations and maximize production. But buying on price alone often harms people, degrades the environment, and reduces the company’s bottom line. How can this be? You met the minimum safety requirements and saved money by buying on price. Don’t those savings go right to the bottom line? When you buy on price you get minimum quality, minimum compliance and are often backed corner with no reasonable options to rectify the problems that arise from buying on price instead of buying on long term life cycle cost. Culturally few companies actually ‘walk the talk’. It is trendy to have giant billboards at plant entrances proclaiming world class compliance with quality and safety standards. Annual reports are embellished with safety slogans and sustainability statements. Behind the front gates and the glossy annual reports the message is clear: produce or be replaced. Only a few companies go beyond the window dressing and actually endorse, from the top down, continuously improving their safety culture. Those that do embrace safety, show significant performance advantages over their competition that are reflected in their safety, productivity and environmental records and, ultimately their financial statements and share price. Current accounting (and reward) systems make it unlikely financial managers will accept non-conventional approaches to justifying expenditures on safety because they are driven to report “hard” numbers that can be documented and are within the “GAAP or IFRS Rules.” But in reality, accountants quantify soft or intangible costs all the time in their financial statements. Justifying safety investments is greatly enhanced by quantifying what most financial managers would call intangible costs. Government agencies have no problem assigning intangible costs to justify regulations to improve safety. How many times have you heard that the regulation is justified because the cost to industry is X while the benefit to the society is 2 or 3X? How can they say that without including intangible costs? We find it hard to believe these government claims of benefits to society because we have been trained to think about saving hard direct costs to justify investments."

Jan 1, 2017

By L. Sandbak

A geomechanical rock mass classification or RMR is currently being used for the evaluation of an LHD mechanized mining system versus the conventional block caving method. The successes and failures of a Panel lS-19 LHD test block on the 2315 level can be attributed to the geologic and geomechanical zonation present. Trench blasting, caving procedures, and sequencing are other factors that were also considered. Lessons learned from the P.lS-19 test block have been used to alter the design for future LHD production blocks on the 2615 level. These modifications are designed to maximize the pillar and insure an adequate draw connection.

Jan 1, 1988