Search Documents

By Gerald L. Finfinger, Michael A. Trevits

Since 1964, the US Bureau of Mines has been conducting a comprehensive program of research on the origin and control of coal bed gas. Several extensive databases have been developed during the work representing information from every major coal producing region in the United States. Gas content measurements have been made on 885 coal samples from 15 states representing 221 coal beds. Records indicate that the range of gas content varies from zero to over 640 ft3 per ton (20 cm3 per gm). During the conduct of the research program, several drilling and completion techniques have been developed or refined to divert and collect coal bed gas before it enters the mine environment. Such techniques include horizontal, cross-measure and vertical boreholes. Samples of gas collected from boreholes drilled under the program indicate that the primary gas constituent is methane which comprises 97 pct, the remaining hydrocarbons make up approximately 0.2 pct. Nitrogen and carbon dioxide account for the majority of the remaining gases at average concentrations of 1 pct each. Surveys have been made on the total daily gas emissions from underground coal mines. In fact, the most recent survey indicates that 180 mines had emissions in excess of 100 Mft3 per day (2.8 Mm3 per day). Furthermore, total mine emissions were in excess of 300 MMft3 per day (8493 Mm3 per day). An analysis of the data showed that there appears to be no relationship between in-place gas content and coal bed gas composition. Furthermore, no correlation was observed between in- place gas content and daily mine emissions. In a general sense, the higher the gas content the higher the relative gas emissions. Perhaps a more direct relationship would be observed if more complete emissions information (including gob gas borehole production) was available.

Jan 1, 1989

By James H. Barks

Exploration for ore deposits in southeastern Missouri in the 1950's resulted in the important discovery of lead, zinc, copper and silver in 1955. Further discoveries in the area led to the naming of the Viburnum trend. It has sometimes been referred to as the "New Lead belt" to distinguish it from older lead-producing areas to the east. As presently developed, the "trend" is 35 miles long, running north and south about 50 miles west of the Lead belt. Galena (lead) is the principal ore mined, with lesser quantities of sphalerite (zinc), chalcopyrite (copper) and silver recovered as economic by-products. The ore body is as much as 140 feet thick and 1,200 feet wide, and is found in the Bonneterre Dolomite (Upper Cambrian) at depths ranging from 700 to 1,200 feet. Since its discovery many companies have engaged in exploration and several major companies have developed new mines and constructed mills and a smelter in the area. The first mine in the Viburnum trend came on stream in 1960, but as more mines came on stream and others reached capacity, lead production increased to the point that the Southeast Missouri Lead district produced 432,576 tons of lead in 1970 to become the world's largest lead-producing region (Missouri Geological Survey and Water Resources, 1971). The Viburnum trend area with its rolling, heavily forested hills and numerous clear running streams is in the Clark National Forest of the Missouri Ozarks. Until the recent development of its mineral resources, the area was sparsely populated and nearly unmarked by the activities of man. Industrial development is almost certain to be accompanied by environmental changes. In a day of growing awareness of the need to preserve the quality of the

Jan 1, 1971

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By B. Mishra

This paper presents a rock mechanics investigation of the time-dependent behavior of the rock immediately surrounding the excavation in a hypothetical one-entry coal mine based on the geology of the Illinois coalfields Research in the area of time-dependency is almost nonexistent and, therefore, this research was performed to make inroads into this neglected research area. Numerical analysis of a typical one-entry coal mine in an Illinois basin was performed using the commercial finite difference program FLAC3D. The immediate roof of the coal entry was assumed to be a shale formation. Shale in other formations has shown a tendency to creep with time. Therefore, in this study the authors modeled the shale in the roof using time-dependent characteristics. The input properties were taken from laboratory creep tests performed on shale. Model runs were performed at different stages, mimicking the progressive excavation of the entry. The model results showed that stresses in the roof attained the limit of yielding. Using Mohr-Coulomb failure criteria, potential zones of failure were also predicted. The results showed that the current computational capacities are sufficient to explore this previously uncharted territory of ground control.

Mar 1, 2014

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

By Richard R. Klimpel

This paper discusses some important industrial interactions between size reduction and downstream froth flotation processes. Experience gained at the industrial level is clearly indicating that how size reduction circuits are designed and/or operated can have a significant impact on froth flotation beyond normal considerations of particle size, liberation, etc. Three specific interactions will be discussed: 1) the impact of steel grinding media versus autogeneous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources; 2) the importance of appropriately utilizing the electrochemical window that is created in the grinding to enhance sulfide mineral recovery by froth flotation; and 3) the interaction of particle size distribution with collector dosage and frother type.

Jan 1, 1995

By W. J. Dolinar, S. P. Sandoval

The US Bureau of Mines (USBM) implemented the Fe2+/ Fe3+-SO2 anode reaction in a Cu-electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/ m2 (24 A/ft2) and 40°C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb), compared to conventional electrowinning. Acid milling 5was completely eliminated, and the SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1996

By A. Wright, R. L. Kastelic, W. C. Feyerabend

Gold Fields Mining Corp. is evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek project, Humboldt County, Nevada. Contamination of reverse-circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse-circulation holes appear to define mineralized zones almost as well as diamond-drill holes. To improve reverse-circulation sample integrity, several techniques were tried (including a stiff-mud injection system) but with limited success. Diamond-core drilling continues to be used in conjunction with reverse-circulation drilling to further delineate the mineralization.

Jan 1, 1993

By Paul B. Queneau, Barry J. Hansen, D. Erik Spiller

Most lead and zinc secondaries are recycled pyrometallurgically. However, many problems encountered in secondary smelters have been solved by addition of physical concentration and/or hydrometallurgical processing steps, with resulting important environmental benefits. U.S. secondary lead and zinc operations are described, covering conventional smelters, EAF-dust treaters, and zinc sulfate/fertilizer producers, including plant capacities, technologies, and outputs. During the past two decades, remarkable advances have been achieved by recycling spent lead-acid battery components. Interaction between primary and secondary zinc producers, the fertilizer industry, and the zinc chemical industry has substantially decreased waste generation.

Jan 1, 1993

By J. E. Bevan

Once mining compromises the stability of a rock mass, the dangerous task of roof bolting begins. Many attempts have been made to automate this process, but there are still many refinements that need to be made. In the past, roof bolting modules were designed around the abilities of a human operator. Currently, researchers are taking a new approach that focuses on designing modules that can utilize bolting methods that are easily automated. A non-rotating anchor that is locked into position by a linear force (as opposed to a rotational force) was designed by researchers at the U.S. Bureau of Mines. Once the bolt is secured in the bolt-hole by the anchor, the bolt is tensioned and a collet is used to secure the other end of the bolt. This process replaces the traditional bolt-nut fastening method. This program is part of an effort at the U.S. Bureau of Mines to automate the coal mining process.

Jan 1, 1994

By Rodger C. Fry

Underground coal mining has been active within the East Mountain property since the mid 1950's. As a result, coal from two seams has been extracted within large areas allowing surface subsidence to occur. Monitoring of subsidence annually, began in 1981 using on the ground conventional monumentation, surveying and photogrammetric monitoring. The data collected has shown the time benefits of photogrammetry and the relationship between observed subsidence and the geometry of the mined out area below.

Jan 1, 1986

By V. T. McLemore

Rare earth elements (REE) are becoming more important in our society. REE deposits are found throughout NM. Some REE past production (1950s), as bastnaesite, came from the Gallinas Mountains district, Lincoln County, NM. Several companies and the U.S. Bureau of Mines (USBM) have conducted exploration programs to identify REE potential. Four types of deposits are found in the district: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipe and iron skarn deposits; all are associated with Tertiary peraluminous, alkaline to alkalic-calcic volcanic rocks. District zonation is defined by base metals (REE-F-Cu veins) that form center of the district, surrounded by REE-F veins. The magmatic-hydrothermal breccia pipe deposits form a belt partially surrounding the veins. Iron skarns formed at the top and edge of the trachyte intrusion and are likely the earliest stage of mineralization. In 1991-1992, USBM calculated an inferred resource of 0.487 million metric tons with a grade of 2.95% total REE. With the projected increase in demand of REE, areas such as the Gallinas Mountains district in New Mexico are being re-examined for additional REE potential.

Jan 1, 2011

By I. Ocak

Initial investment for mechanical boring of tunnels is found to be high in most cases. Conventional drilling and blasting is not the possible especially in urban area. In these conditions impact hammer offers many advantages over conventional drill and blast techniques and boring tunnels. These include improved safety, minimal ground disturbances, elimination of blast vibration, reduced ventilation requirements, reduced cost etc. Therefore, hydraulic impact hammers have been used widely in metro tunnelling projects in Istanbul since 1992. Accumulated and published data from various tunnelling projects serve to improve predicting the machine performance and scheduling of job duration. This paper is prepared under this objective. Machine utilization time of impact hammer was evaluated in this study. The main rock formation named Kartal formation arepaleozoic aged sedimentary rocks, shale, sandstone, siltstone, andesite dykes and sediment fillings. The first stage of the project is commissioned to Yapi Merkezi- Yuksel- Dogus- Yenigun- Belen consortium.

Jan 1, 2011

By D. Panias

Alumina hydroxides such as gibbsite (Al(OH)3) and boehmite (AlOOH) are precursors of many types of alumina that find important industrial applications. The thermal decomposition of AlOOH, which is a more energy saving precursor compared to gibbsite, gives rise to the formation of ?-, d-, ?- and a-aluminas that are used for the production of catalysts. The applications of the aluminas are governed by their properties that are a function of the precursor material and its microstructure. The microstructure in turn is a factor of the method and conditions applied, as well as, in the case of soft chemical processes, on the anions present. Towards these ends, this study was focused on the effect of different anions on the physicochemical characteristics of the alumina hydroxides precipitated in the first 5 minutes after the perturbation of the stability of a supersaturated sodium aluminate solution (Bayer liquor).

Jan 1, 2006

By R. O. Harma

Wet autogenous grinding is utilized in three iron ore concentrating plants operated by The Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping.

Jan 1, 1982

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro NC treating crude Waelz Oxide (WOX) to produce Special High Grade Zinc by a hydrometallurgical process, comprising leaching, zinc solvent extraction/electrowinning (SX/EW), melting and casting and bleed treatment. Cadmium removal by zinc dust cementation plays an essential role in the bleed treatment circuit to prevent a build-up of cadmium in the circuit. Silica, although not present at significant levels in the WOX feed material (approximately 0.3%), had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also impacted. The silica levels were mapped throughout the circuit in an attempt to identify the source of the silica issues. Adjustments including using PLS as feed to cementation, pH control in WOX leaching and neutralization have been introduced to mitigate the issues created by silica gel in the circuit. INTRODUCTION Located in North Carolina, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz Oxide (WOX) to produce Special High Grade (SHG) zinc. The flowsheet, known as the Modified Zincex® process, consists of leaching, solvent extraction, electrowinning, melting and casting and bleed treatment as illustrated in Figure 1. Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The Cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press Silica can be found in several forms in acid leaching. The first form is fine silicate particles. The size of the particles can vary from one to twenty microns (1). Fine silicate particles can lead to the formation of crud in solvent extraction circuits (2, 3). At Mooresboro, crud has been observed in Depletion, which is part of the solvent extraction circuit. Silica content in the solution in this section is high. The second form of silica is monosilicic acid Si(OH)4, which begins to polymerize almost immediately upon being leached into solution. Monosilicic acid polymerizes to silica gel or a silica precipitate dependent primarily on supersaturation (5). Factors that influence the rate of polymerization include temperature, sulfuric acid concentration / pH, hydrofluoric acid concentration, seeding, and dissolved salts concentration such as zinc and aluminum in the solution (4, 5, 6). In sulfate systems, silica solubility is reported in the range of 150 to 450 ppm of SiO2 (3, 5, 7)."

Jan 1, 2016

By J. Brad Dalton, Sam Vance, Trude V. V. King, Roger N. Clark, Raymond F. Kokaly, Gregg A. Swayze, Dana J. Bove

Visible-wavelength and near-infrared multispectral image cubes for the Animas River Watershed from Hermosa, Colorado to the headwaters at Animas Forks, Colorado were acquired on June 18, 1996 using the Jet Propulsion Laboratory's AVIRIS (Airborne Visible and InfraRed Imaging Spectrometer) instrument (Green et al., 1998). These image cubes have been analyzed using the USGS Tetracorder V3.4 implementation (Clark et al., 1995), an expert system which utilizes a database of more than 300 laboratory spectra of endmember minerals and mineral mixtures to generate maps of mineralogy, vegetation coverage, and other material distributions. Major iron-bearing, clay, carbonate, and other minerals were identified along with several minerals associated with acid-generating hydrothermal systems including pyrite, jarosite, alunite and goethite. Additionally, distributions of alkaline minerals such as calcite and chlorite indicate a relation between acid- buffering assemblages and stream geochemistry within the watershed.

Jan 1, 2000

By H. A. Kortmann

Blast furnace operators have been steadily increasing their quality requirements on burden material. These requirements include a high reduction rate of the ore burden as well as good strength at the beginning and during the whole blast furnace operation. Special requirements are made on the softening and melting behavior which ensures an optimal formation of the cohesive zone in the blast furnace. On the whole, the self-fluxed and olivine-based pellets meet these higher requirements due to their chemical composition, especially in the pure pellet operation. In the mixed sinter/pellet operation partly-fluxed and acid iron ore pellets can be appropriately used. The paper describes the demands on, and characteristics of, different kinds of pellets used in the Federal Republic of Germany.

Jan 1, 1989

By A. R. Laplante

The mineralogy of the Joe Mann mine differs from that of other deposits of the Chibougamau area that are exploited by Les Nines Camchib Inc. It is characterized by very fine first generation gold and very coarse second generation electrum. Successful processing required adjustments of the processing flowsheet, which includes gravity, flotation, and cyanidation. A study of coarse gold liberation in the gravity/grinding circuit is described. Modifications to the flotation circuit and the reconditioning of a small capacity cyanidation circuit are presented.

Jan 1, 1989

By BO HYUN KIM, MARK K. LARSON

The floor-heave and no-floor-heave phenomena at a western U.S. coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria. Although the previous numerical study using FLAC3D very reasonably demonstrated these phenomena, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. As a result, the latter models predicted floor heave that agreed with relative amounts of observed heave from each gateroad system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Sep 1, 2022