Search Documents

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By R. B. Inturi, R. G. Reddy

Solid-state reduction of roast Movat chromite ore with carbon was carried out as a function of the C/FeO ratio at temperatures ranging from 800°C to 900°C. The reduction was studied using thermogravimetric analysis (TGA). A two¬stage mechanism consisting of the reduction of FeO with carbon monoxide and the regeneration of CO by the oxida¬tion of carbon with CO2 was proposed. The rate-controlling step is the carbon oxidation reaction. A kinetic equation, that of random nucleation, was proposed. The activation energy for the reduction was determined to be 55,800 J/mole and is compared to those activation energies determined for other chromite ores.

Jan 1, 2000

By Jakub Nalaskowski, Robert Aranowski, Jan D. Miller, Jan Hupka

The polyolefins, mainly polyethylene and polypropylene particles, are used as an active filler material in polymer-polymer blends and are being used for the modification of asphalts to pro- vide for high-load, low-maintenance road construction. The stability of prepared blends depends on the interaction forces between polyolefinfiller and the matrix and/or between two polyolefin filler surfaces in the polymeric matrix. Various additives, especially surfactants, can be used to modify these interactions and improve the stability of polymer blends. In current research, direct force measurements between polyethylene (PE) surfaces in n-tetradecane, a nonaqueous solvent imitating the polymer matrix, were performed in the presence of lauric acid and dodecylamine using the AFM colloidal probe technique. Additionally, the zeta potential of polyethylene particles in the presence of surfactants in n-tetradecane was measured. The interac- tion forces between the polyethylene surfaces can be described as a combination of electrical double layer repulsion and steric repulsion between polymer chains extending into the n-tetradecane sol- vent. The addition of surfactant to the n-tetradecane was found to increase the repulsive force between the PE surfaces. The strongest repulsion was observed for dodecylamine. Additionally, the temperature efect on the interactions in n-tetradecane was studied. It was found that steric repulsion between the PE surfaces increases with an increase in temperature.

Jan 1, 2003

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By Syd S. Peng

The key design parameters of roof bolting using expansion - shell type support for underground coal mine roof support are bolt length, bolt spacing, installed load and anchorage capacity. Depending on the utilization of suspension effect or friction effect, the bolt length is dictated either by the distance between the roof surface and the first overlying strong strata encountered or the desired magnitude of reduction in bending stress at the roof surface, The current prevailing practices about the bolt spacing and installed load are that an initial torque of 125 - 170 ft-lbs is applied and the bolts are spaced at 4- or 5- ft. square grid pattern. This seems to be a rather broad generalization in view of the great geological variances which are expected in underground coal mines. A modest evaluation program to measure the effectiveness of current roof bolting practices is to monitor the load history of roof bolts during a complete mining cycle including the phases of room development and pillar robbing. The load history, when compared with the anchorage capacity of roof bolts determined by in-situ pull tests, will provide information for evaluating the installed load, the bolt spacing as well as the specifications for structural and anchorage characteristics of the bolt assemblies. This paper presents a case history of monitoring the complete load histories of roof bolts in an underground coal mine of Pittsburgh seam.

Jan 1, 1976

By J. E. Stephens

US Borax began exploration in southeast Alaska in the summer of 1971 with a staff of two, Barry Watson and Jackie Stephens, based in Spokane, WA. After several years of prospect examinations in the islands west of Ketchikan, AK, and with the able assistance of prospector-pilot Kenny Eichner, Jackie Stephens proposed and organized a boat-based, helicopter-supported, stream sediment sampling program to explore the western contact of the Coast Range intrusive complex on the mainland. The rationale for this included: the extension of known mineral trends from Canada into southeastern Alaska along favorable geologic zones; the western contact area of the Coast Range intrusives with metasediments and metavolcanics was a favorable target for metals exploration as shown by numerous small prospects. Knowledge gained from mineral exploration of the island areas indicated that they were well mineralized, but already well explored, and that the known mineral potential was probably present in subeconomic quantities (Brooks, et al.). Publications of the US Bureau of Mines and other scientific agencies were gathered and every prospect within the southem southeastern Alaska area was plotted. This in itself lent a tremendous amount of knowledge to the total exploration program. US Borax's McLean Arm copper property on Prince of Wales Island was drilled and dropped while this compilation of data was proceeding. We found that many companies had followed one another around the island areas, but little or no exploration had been done on the west side of the Coast Range, and that many explorationists flatly stated that the west side of the Coast Range was barren of mineralization. In summary, although some of the shoreline and near shoreline areas of the mainland had been explored, no organized boat-helicopter exploration program had been done along the favorable western zone of the Coast Range Intrusive complex. We decided to use a boat as a floating hotel for the crews that were to be helicoptered into the back country from tidewater for our initial stream-sediment sampling program.

Jan 1, 1991

By James T. Baxter

Underground mining of limestone is becoming increasingly attractive in Illinois. Most quarries are near rivers on the western and southern borders where competition for land use is intensive. Increasing demands for stone can be met by expanded mining with access by edits in existing quarries and by inclines and shafts at downdip sites. Geologic, hydrologic, and engineering conditions indicate that deep mines in the Ste. Genevieve, St. Louis, Salem, Ullin, and basal Burlington Limestones of Mississippian age and in the Moredock Limestone Member of the Dunleith Formation of Ordovician age are possible, but development will require prudent exploration and planning to ensure that the product will be of good quality.

Jan 1, 1978

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By F. Forbes

For many years, the Machinery Division of Dravo Corporation has been designing and constructing bins and hunkers as part of overall plant facilities. We have designed bins to handle a variety of materials including coal, coke, iron ores and concentrates, sintered and pelletized ores, calcined and raw limestone, bentonite, alloys for BOF shops, and even cast iron chips from machining operations. We, along with everyone else in this business, have had our bin problems. The bins either plug, rathole, segregate, wear out, flood the discharge device, or overload it. Surprisingly, sometimes they have worked. As engineers, it has long concerned us that something as important as bin design should be so imprecise and that it has been so conspicuously avoided in research and in literature. In past years, rule-of-thumb design criteria had been to keep the sides of the bins as steep as possible and the outlets of the bin as large as possible. This criteria led to the design of bins with 600 to 700 side slopes and table feeders which were very large. Unfortunately, this meant trying to fit tall, skinny bins into a layout where minimum building height was required for obvious economic reasons. Like everyone else in the industry, we found that this design procedure was expensive and ineffective.

Jan 1, 1968

By Charles F. Herbert

The waves of prospectors who struggled across the wide Alaskan wilderness between 1898 and 19 10 came close to but did not actually find the rich copper/zinc/silver deposits strung out along 161 km ( 100 miles) of felsic schist in the remote Brooks Range of northwestern Alaska. They had heard rumors of gold in the valley of the Kobuk River, so they skirted the Arctic ice pack in the Chukchi Sea and, in a force at least 800 men strong, ascended the Kobuk River in 1898. Twenty-eight placer mining camps were established but only a handful survived for more than a few years. One of the placers that died rapidly was Ruby Creek. A map showing the location of Alaskan mineral deposits is given in Fig. 1. The Ruby Creek miners, disappointed with the scarcity of gold in that creek, followed copper-bearing float to two places where the float was especially plentiful. Pits, a short adit, and a shallow shaft uncovered copper carbonates, bornite, and chalcopyrite in fractured limestone but the remoteness of the district blocked efforts to sell the claims or to raise capital for development. Shortly after 1906, the copper prospects were abandoned and, except for an account published in 1913 by the US Geological Survey, they were forgotten, as were the names of the prospectors.

Jan 1, 1991

By Vinton A. Garbesi

The construction involved in the Washington Metropolitan Area Transit Authority (WMATA), Contract No. lK0011 (K-1), encompassed some 2,621 meters of single track parallel tube rapid transit tunnels, 335 meters of cut-cover subway station and appurtenant ventilation structures at each end, and a fan shaft at approximately the mid point of the tunnels. The construction contract was awarded June 7, 1974 to a Joint Venture consisting of Intercounty Construction Corporation, Hyattsville, Maryland, and S $ M Constructors, Inc., Solon, Ohio. The former being responsible for performing the cut and cover construction, and the latter being charged with constructing the running tunnels and fan shaft at their mid point. (See Fig. 1) The problems of mining and supporting, the 183 meters of twin tunnels just east of Court House Square Station, by unique mixed face and soft ground mining methods is the main subject of this report, although a general review of the tunnels in their entirety, as well as the geology encountered in the excavations, is presented to give a better overall setting for the problems encountered. GEOLOGIC SETTING The tunnels for the K-1 contract are located in three general types of material; the first being fractured and metamorphosed ignious rock (quartz-hornblende-biotite gneiss), the transition zone between weathered and competent rock, and in ground consisting of the weathered

Jan 1, 1979

By S. S. Peng, Luo. Y.

In a shearer longwall mining operation, the longwall hits are responsible for breaking into and chipping the broken coal blocks away from the coal face. However, underground observations found that the bits being used were working under various degrees of wear. This wear can be reduced by using better-designed longwall bits and by properly selecting shearer operating parameters. A computer program was developed to simulate the performance of the longwall bits. The information required by the program are the shape of the bit head, the installation of the bits on the drum and the operation parameters. Through the simulations, the main factors affecting the bit-wearing process are identified. Suggestions are also made for improving the design of the longwall bits.

Jan 1, 1998

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993

By Jozef F. Zurawski

The paper discusses design and construction of a 1.8 meter (6 ft.) diameter tunnel installed under complex geology of Staten Island, New York. Contract T-13 is a section of the Oakwood Beach Water Pollution Control Project constructed for New York City Department of Environmental Protection. A knowledge of the subsurface conditions and difficulties experienced on the adjacent contracts called for an innovative approach to handle tunneling under 12 to 17 meters (40-55 ft.) of water in the variable subsurface conditions. This paper describes tunnel design and construction utilizing continuous grouting during advancement of tunnel boring machine and installation of liner plates.

Jan 1, 1993

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring, system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's design philosophy, hardware and software components, examples of installations, and a few observational results.

Jan 1, 2002

By J. M. Richardson, A. L. Mular

Metallurgical balances are fundamental to the successful design and operation of concentration and dewatering circuits. With computerized balance techniques gaining prominence in recent years, it is essential that engineers understand the basic principles that underlie the new methods, as well as the various applications for design of new plants and analysis of existing operations. This chapter discusses two important types of metallurgical balance: (1) steady-state design (2) operating data adjustment Application of computerized steady- state design balancing is demonstrated through the example of a typical copper concentrator flowsheet. Operating data adjustment to achieve a consistent balance is demonstrated for a typical concentrator operation.

Jan 1, 1986

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By Fred C. Caspall

During the last century the importance of coal as a natural re- source has frequently come to the attention of the general public, but never before nave circumstances combined to focus as much attention on coal as it receives today. There is the ever increasing demand for energy that can be met only by coal consumption, coupled with a growing awareness of man's potential for despoiling his own environment. Society monitors the use of the remaining resources with an increasingly critical eye and, for obvious reasons, surface mining operations tend to draw an unusual amount of public attention. While the surface mine is a successful economic competitor with other uses of the earth's outer skin, one of the unrewarding results of such activity is tile simultaneous destruction of two of our most important resources--the coal seam and the surface soil. In a relative sense the coal seam is a nonreplaceable resource but the surface soil can be restored. Unfortunately, little attention has been given to land reclamation and even less has been devoted to the restoration of a productive surface soil. The research reported in this paper was de- signed to test the relative productivity of newly reclaimed surface mine spoils in western Illinois. The results are preliminary in nature but may aid in the future redevelopment of mine spoil soils in the Illinois Coal Basin.

Jan 1, 1975

By G. Gaidajis

Sea water samples collected from coastal waters in the vicinity of the Stratoni mining operations, in North-Aegean Sea were analysed for dissolved metals and elements. The maximum concentrations observed were one to three orders of magnitude lower than the environmental limit which coincides with the quality of sea waters suitable for swimming purposes. The quality of the coastal sea waters are affected by the natural mineralization of the area and the urban activities drained through local small rivers, the past mining activities present in the sea bottom sediments in the form of disposed tailings, and finally by the presence of the adjacent Mill-Flotation Plant. The relative importance of the treated final effluents discharged from the mining operations is considered to be insignificant.

Jan 1, 2006

?Classification System Efficiency (CSE)? is a simple, powerful concept which can be used to measure and improve ball mill circuit efficiency. This paper describes six plant case studies which demonstrate the use of CSE to diagnose and/or improve grinding circuit performance, with related improvements in circuit efficiency ranging from 3 to 30 percent. The increased effective mill grinding energy is recaptured from energy that was going into over grinding, which can greatly benefit downstream mineral separation. The achievable CSE for given circuit design/operating variables is described, providing every plant metallurgist with the means to determine the potential for increasing their particular grinding circuit?s efficiency through increased CSE.

Jan 1, 2012