Search Documents

By Basil W. Mercer

Increased emphasis on industrial pollution control has intensified investigation of waste treatment technology for methods of reducing the amount of pollutants discharged by industry. The mining and mineral processing industry can point to a record of considerable accomplishment in the field of wastewater treatment and reclamation because these operations are so frequently an integral part of the entire operation of an ore dressing facility. This is amply demonstrated by metal producers in the arid regions of the Southwest where water shortages require maximum use of available water. For example, the copper industry in Arizona during 1960 employed an estimated 184 billion gallons of water of which 87% was reused water. (1) Only 0.0003% was discharged to streams and the remainder was consumed by evaporation (8%) and seepage (5%). The most severe pollution problem facing the mining and ore processing industry today is that resulting from acid mine drainage. This problem is largely associated with the mining of coal although it occurs to a lesser degree with the mining of other materials. The degradation of streams by acid mine drainage in the vicinity' of the Appalachian coal fields has been widely publicized and a major effort is underway to determine the best means of correcting this situation. Other forms of pollution from mining operations are less well-known, but it is anticipated that improved or advanced waste treatment techniques will be required for segments of the industry to comply with new pollution control regulations. The current emphasis on redefining hazardous levels for heavy metals and various chemicals with regard to the total environment will in all likelihood lead to tighter discharge controls in some cases. It is the purpose of this paper to review some of the waste

Jan 1, 1971

By D. G. Ball

Other than being used to convey fill material for the gob stowage or building of ribside packs on advancing longwell faces, pneumatic conveying has not been used for the transport of materials on a large scale in mining operations. The technique is extensively used in the wood products industry for conveying wood chips, limestone and other ingredients for the manufacture of paper, for the transfer from railcars, barges or ships to silos or stockpiles and further transfer into the pulp mills. This method of material transfer has the distinct advantage of transporting suitable material over horizontal and vertical distances within the same system. In considering material associated with mining, this includes, ore, coal and rock up to 4 inch cubed size, throughputs of 200 tons per hour over horizontal distances of 3000 feet or vertical lifts of 2000 feet. In recent years tests have been carried out to determine the physical and economic limitations of pneumatic hoisting, the results of which have led to the installation of two fully productive coal hoisting systems at mines of the National Coal Board in Great Britain. The equipment used for the pneumatic hoisting of coal or waste rock is described in this paper, together with a brief history of the tests which led up to the installation of the two hoisting systems in Great Britain.

Jan 1, 1977

By Joe Silvestri, James Carroll, Steve Rondinelli, Raelene Shelly, Jason Miller

"The I-70 Eisenhower-Johnson Memorial Tunnel (EJMT) Fixed Fire Suppression System (FFSS) will help protect the traveling public as well as the entire tunnel itself, which is a critical asset of the Colorado highway system. This project is part of an effort to avoid any closure or long-term damage to these tunnels after a fire event. Historically, the EJMT complex has experienced two to three fires a year. While CDOT has firefighting capability at the EJMT complex, the fixed fire suppression system will provide first responders the critical time needed to safely approach the scene and take action, and is a necessary tool in combating tunnel fires, keeping the public safe, protecting the tunnel structure, and minimizing disruptions to traffic. This paper provides a case history of the first-of-a-kind design and construction of the EJMT FFSS. Major project elements include; water-only deluge fire suppression system, fiber optic linear heat detection system, updated fire alarm system and new drainage system. PROJECT BACKGROUND The I-70 EJMT FFSS was awarded to the Design Build Team lead by Barnard Construction, supported by Rondinelli Life Safety, BCER Engineering, ILF Consulting, Western States Fire Protection and Systems Group. The team conducted successful live fire tests at the Boulder Regional Fire Training Facility in November 2014, with the final design of the FFSS and other supporting infrastructure completed in the spring of 2015. Construction began in early summer of 2015 and the project was completed in December 2015. While CDOT currently has firefighting capability at the EJMT complex, this project features an intelligent linear heat detection system that can accurately identify a fire within feet of its location and subsequently activate the corresponding water-only FFSS deluge zone, bringing water in from an existing supply system on the west side of Loveland Pass. The detection system also activates cameras so the EJMT onsite control room personnel can view and better assess a fire event. The uniqueness of this design is that the majority of the installation occurred above the traffic lanes in the tunnel, which resulted in minimal impacts to motorists below. The fire suppression system will help protect the traveling public as well as the tunnel structure, a critical asset to the highway system. This project is intended to reduce damage and avoid long-term closures of the tunnel due to fires. A long-term closure could cost Colorado billions of dollars and negatively impact tourism along the I-70 mountain corridor."

Jan 1, 2016

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By R. M. Jacobs

Can your company afford to issue a check today for $100,000, $500,000, $2,000,000, or $22,000,000? This is what it might cost your company if it is on the losing end of a product liability suit. During the past 10 to 15 years, the number of product liability actions has grown from a handful per year level to a hundreds of thousands per year level. Settlements and awards in the tens and hundreds of thousands of dollars are not unusual in these days. The largest award that the authors haw heard about is a case involving a private airplane and the death of four men, which was awarded over $22,000,000. In the materials handling field, a fork lift truck, ordered with an overhead guard, was delivered without a guard because one was not available at the time. An accident with serious personal injury followed. Wouldn't it have been better to have waited until the guard was available before delivering the unit? Answer: a quarter of a million dollars better -- the cost of the settlement. Hoisting devices are also not without their liability precedents. In a 1960 case, an employee was injured when a load abruptly fell from a hoist. It was determined that the operator could not possibly have caused such a fall had the hoist been functioning properly. The case was compounded when the manufacturer of the hoist contended that the load had been improperly connected to the device, since the same hoist was used to remove the weight from the injured man without another malfunction.

Jan 1, 1973

By R. Michael

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of underground coal-mining equipment, an example of which is a roof bolting machine. Field studies show that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and it contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel and chuck radiate a significant amount of noise during drilling. NIOSH and the Corry Rubber Corporation have developed a bit isolator that breaks the steel-to-steel link between the drill bit and drill steel and a chuck isolator that breaks the mechanical connection between the drill steel and the chuck. This effectively reduces the noise radiated by the drill steel and chuck and reduces the noise exposure of the roof bolter operator. The paper documents the evolution of the bit isolator and chuck isolator. Laboratory testing confirms that production bit and chuck isolators reduce the A-weighted sound level generated during drilling by 3.7 to 6.6 dB

Jan 1, 2010

By Matthew E. Fowler

The Central Subway will extend the recently completed 8.2-km long Third Street Light Rail line another 2.7 km north through the Union Square shopping district to Chinatown with a concourse-to-concourse connection to the Powell Street BART Station. One mined and two cut-and-cover subway stations are planned. Particular challenges include: tunneling under existing tunnels; variable ground conditions ranging from saturated alluvium to fractured bedrock; a congested urban setting and large-span caverns. This paper gives an overview of the project as it stands midway through the preliminary engineering stage along with a discussion of the rationale and design approaches that are being used to address the construction challenges of restoring light rail service in the most densely developed areas of San Francisco.

Jan 1, 2008

By Ali Soofastaei

Mining operations are increasingly data-rich yet decisionconstrained. Fragmented systems, variability in geology and operations, and sustainability obligations create multiobjective trade-offs that classic analytics cannot reconcile at operational tempo. This paper proposes an end-to-end framework that fuses digital transformation practices (governed data platform, semantic layer, feature store, and MLOps) with generative AI (retrieval-augmented generation, tool-use, and agentic workflows) and decision intelligence (simulation/digital twins and multi-objective optimization). We formalize sustainability-aware objectives, define a practical stack and governance controls, and demonstrate how an AI “decision copilot” can surface options, quantify trade-offs, and document rationale. Two figures illustrate a production-grade architecture and a Pareto frontier for cost–emissions trade-offs; two tables operationalize decision-domain mapping and a transformation maturity rubric. The approach is product- and company-agnostic.

Feb 22, 2026

By Paul Cameron Gilmour

Geologically, as distinct from economically, "porphyry copper (molybdenum, gold, silver, etc.) deposits" might be defined as large, disseminated and/or stock-work occurrences of copper-minerals, generally averaging less than 1 per cent cop-per. They are normally associated with small plutons which range in composition from granite to diorite, although, typically, they consist of quartz monzonite or granodiorite. Circumstantial evidence indicates that these "minor" granitic intrusions may represent the intrusive phases of post-orogenic, calc-alkaline volcanism, this conclusion being suggested by: 1. Texture and grain size. 2. Prevalence of intrusive breccias. 3. Relationship to unconformities and estimated depth of emplacement. 4. Spatial distribution in relation to orogenic zones. 5. Age of mineralization and igneous episodes

Jan 1, 1972

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader's orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature's effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993

By David Yankovich, Geoff Hughes, David Haug, Jon Kaneshiro

"In March 2013, the Sanitation Districts of Los Angeles County began final design of the Joint Water Pollution Control Plant (JWPCP) Effluent Outfall Tunnel project. The new, approximately 7-mile, 18-ft internal diameter tunnel will provide additional capacity and redundancy for the existing 8- and 12-foot diameter tunnels, which were built in 1937 and 1958, respectively. Connections to an existing, active 14-foot arch force main and four existing ocean outfalls ranging from 5- to 10-foot diameter are required. This paper will present geological features for the project, and details of the proposed post-tensioned tunnel liner and associated structures. INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) are 23 independent special districts serving approximately 5.3 million residents in Los Angeles County. Seventeen of the districts that furnish sewerage services to the metropolitan Los Angeles area are signatory to a Joint Outfall Agreement that provides for a regional, interconnected system of facilities known as the Joint Outfall System (JOS). The JOS service area is shown in Figure 1. The JOS serves an area that encompasses 73 cities as well as unincorporated territory and parts of the City of Los Angeles. The JOS provides wastewater collection, treatment, reuse, and disposal for residential, commercial, and industrial users, and it includes seven treatment plants, the largest of which is the JWPCP, located in the City of Carson. Currently, secondary treated effluent is conveyed through two 6-mile long parallel tunnels, 8- and 12-feet in diameter, from the JWPCP to a manifold structure located at Royal Palms Beach, near White Point on the Palos Verdes (PV) Peninsula, from which four seafloor outfalls extend offshore. The two main outfalls, 90- and 120-inches in diameter, extend approximately 1.5 miles offshore and discharge at a depth of approximately 200 feet below sea level. The other two outfalls, 60- and 72-inches in diameter, are used for additional capacity during heavy rain events and extend a shorter distance offshore and discharge at shallower depths. A schematic of the existing system with the proposed tunnel and structures is shown in Figure 2, and the proposed 18-ft diameter tunnel alignment is shown in Figure 3. Both existing tunnels and main outfalls are required to be in service at all times."

Jan 1, 2016

By John L. Burnett

Field criteria are needed to help the prospector recognize a potentially expansible shale, clay, or slate. Certain criteria have proven useful in California even though the physical-chemical mechanisms of expansion are not thoroughly understood. Three conditions must be satisfied before expansion can take place, The raw material must partially fuse at a low temperature (1800-2000°F.), Concurrently a gas must form. The raw material must be sufficiently impermeable to trap the gas within the particle. Low temperature melting, which is controlled by bulk chemical composition, is difficult to assess in the field but most common shale, clay, and slate is suitable in this respect, The presence of organic carbon, the most common source of an expanding gas, is indicated by dark color of the rock, A large proportion of clay-sized particles promotes impermeability; fine grain-size is indicated by conchoidal fracture, The shape of the expanded particle is commonly indicated by the texture of the raw material. Rocks with well-developed slatey cleavage produce accordion-shaped particles; massive rocks tend to form rounded particles. Undesirable materials commonly present with expansible shale include: weathered shale; sandstone and other coarse-grained sediments; and limestone, Weathering, which is indicated by color, reduces or eliminates expansion; therefore, surface samples seldom are representative of the shale found at depth. Sandstone does not expand and will increase the average weight of the finished product, Limestone or particles of carbonate minerals can be actively harmful because they are converted to free lime (CaO) during the firing process, If free lime is present in concrete, hydration will cause expansion of the lime particles which result in surficial ?popouts.?

Jan 1, 1963

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Patrick Maier, Gregory E. Bogin Jr

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. As a result, the severity of mine explosions ranges from minor damage to loss of lives and permanent mine closure. Experimental results have shown that the inclusion of obstacles can significantly increase the flame propagation velocity by inducing turbulence. This research focuses on explosion experiments in a 71 cm diameter, 30.5 m long reactor that includes rock piles as obstacles along with developing the corresponding CFD model that captures the observed flame behavior and interaction with the obstacles. The rock rubble increases the flame front propagation velocity by 500% compared to the maximum velocity observed in the empty reactor experiments. The 2D and 3D CFD models predict the experimental flame front propagation velocity, whereas the 3D model shows a more explicit conformity than the 2D model. Although the computational time to complete the simulation is much less for the 2D model than for the 3D model, the 2D model is not sufficient to simulate cases with rock rubble since it cannot capture the propagation of the flame through the small voids between the rocks with the same effective blockage ratio as the 3D model. The validated CFD model can be scaled up to simulate methane explosions in full scale mine and industrial settings.

Nov 20, 2023

By G. J. Hartman

A presentation of this project was given previously at the SHE Annual Meeting, Denver Colorado February 23-27, 1987. The project concerns the development of in situ recovery of borate products from a deep-seated colemanite deposit in California. The deposit contains some 147 million tons of borate ore containing 6.4% boron oxide (B2O3). This paper involves the numerous changes in the process that has taken place since that first presentation. This paper further explains the reasons for these changes which are primarily environmentally based and secondarily capital requirements related.

Jan 1, 1994

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By M. T. Ityokumbul

The use of yield index, the product of the yield and gangue rejection, for the optimization of separation processes is presented. The characteristics of the yield index are contrasted with separation efficiency calculations and applied to laboratory froth flotation and washability data. Data from continuous froth flotation tests conducted to "optimize" froth flotation using process optimization software were also evaluated with the yield index procedure.

Jan 1, 1997

By H. R. Weischedel

The art of wire rope inspection has advanced rapidly over the past decade. Present electromagnetic (EM) wire rope inspection instruments provide an important and often vital element of wire rope inspection. Some instruments are easy to operate and offer simple and clear data interpretation. Simultaneously, wire rope inspection and retirement standards are becoming simpler and more lucid. Future guidelines will he easy for inspectors to apply and for rope operators to fulfill. The thrust of evolving regulations is clearly toward periodic EM inspections supported by visual inspections. These development sallow even moderately skilled personnel to perform EM inspections of wire ropes. Therefore, it is now possible and cost effective for wire rope users to have EM and visual inspections performed by in-house personnel. In-house EM inspections have many advantages and offer an excellent return on the initial investment. Since EM inspections can detect rope deterioration in its beginning stage, wire rope users recognize that they are an effective preventive maintenance tool. For instance, the early detection of wear or corrosion allows immediate corrective action. This can easily double, or even triple or quadruple, the service life of a rope.

Jan 1, 1991

By John L. Stafford

The ROEMMC combustion system was originally conceived as a means of utilizing solid fuels that would otherwise have been wastes requiring disposal and convert these fuels into useful energy sources. This concept follows as an extension of the application of residual waste incineration with energy recovery practiced in the lumber, manufactured board, sugar cane, and other industries. The incineration of these wastes in the furnaces of steam generating equipment is thoroughly described (1, 2, 3, 4, 5, 6, 7). The fundamental principle of the ROEMMC system is temperature control which makes possible the maintenance of the non-combustible fraction of these solid fuels in a dry solid state and their separation from the gaseous products of combustion. This philosophy of ash removal and the "slagging" philosophy are compared. The ROEMMC equipment function and applications are described.

Jan 1, 1978

By Fan Yang, Zhiping Wen, Tiancheng Nie, Jinhe Pan, Ruibo Jia, Changchun Zhou

Rare earth elements have important strategic significance and economic value, and the rare earth elements in coal resources have considerable development potential. This study took coal refuse in the Jungar area of Inner Mongolia, China, as the research object, and investigated the occurrence modes of rare earth elements. A special sequential chemical extraction experiment was designed, and the results showed that the rare earth elements in coal refuse mainly occur in silicate and aluminosilicate form, accounting for approximately 65% of the total rare earth elements. According to the results of SEM-EDS, micro morphology of the sample belonged to the lamellar structure of clay minerals, and Al, Si, Fe, S, Y, and La were all present in the sample. Through SPSS software analysis, rare earth elements have an obvious linear positive correlation with Al, Si, and Fe elements, and a negative correlation with S elements. The rare-earth element occurrence mode in coal refuse can provide a definite theoretical basis for the later extraction and enrichment work.

Feb 18, 2022

By O&apos

Southern Ohio Coal Company (SOCCO) and the U.S. Bureau of Mines have identified techniques to optimize the use of scrubbers on continuous miners. The techniques provide maximum respirable dust control while maintaining a high output. The use of radio remote control and scrubber help to achieve greater advance between lifts by locating the operator in fresh air during the mining cycle. He is also kept away from newly exposed roof, which is not supported. An alternative to fan-powered scrubber was also evaluated at SOCCO. A high-pressure water-powered scrubber system eliminated the noise associated with fans, and achieved an intrinsically safe system. Experience in the use of these scrubber systems and remote control at SOCCO are discussed.

Jan 1, 1990