Search Documents

By Greg Barfoot, Kurt Keskimaki

The Henderson Mine is located approximately 50 miles west of Denver, Colorado. A project is underway to replace the existing rail system which transports molybdenum ore 15 miles from the mine to the mill using three flight conveyor system. The first conveyor is a 1 mile, high lift conveyor which transports the ore from an underground crushing station to the end of the existing rail tunnel. The second conveyor is 10 miles in length and utilizes the existing rail tunnel to transport the ore from the mine, which is on the east side of the Continental Divide, to the mill located on the west side. The third conveyor takes ore from the tunnel portal to the mill through a series of 7 horizontal curves and inclines up to 15 degrees. The project applies advanced conveyor design to tackle the installation of the system in an operating mine and achieve the highest possible level of reliability. This paper outlines the design process for this system, discusses the options which were evaluated and how the current design evolved.

Jan 1, 1998

By M. Hakan Morcali, Onuralp Yücel, Haldun Gürcan, Serdar Aktas, Semih Özbey, Alper Keskin

"This work presents a method for the precipitation of cobalt sulfate by alcohols, specifically ethanol and methanol. The effect of the initial concentration of cobalt, the volumetric ratio of alcohol to cobalt sulfate solution, the addition of sulfuric acid and ammonia, and the effects of common ions on the precipitation percentage were investigated. The performances of ethanol and methanol were compared in terms of the precipitation percentage of cobalt sulfate, and explanations for different performances are offered. In the sulfate-based solution, the alcohol was shown to displace water ligands from the first coordination sphere of the cobalt(II) cations, which led to the precipitation of the cobalt ions as cobalt sulfate heptahydrate. SEM analysis revealed that the particle sizes of the powders produced by this method are smaller than those of commercially available cobalt sulfate. The scientific literature contains no data on the solubility of cobalt sulfate in ethanol. In this study, the solubility product constant (Ksp) for cobalt sulfate was experimentally calculated to be approximately 1.15 x 10-5.IntroductionCobalt sulfate, which is one of the most important compounds of cobalt, is used in the electroplating and electrochemical industries. The addition of cobalt sulfate to nickel-plating baths makes the treated metals brighter, harder, smoother and more ductile (Armstrong et al., 1988). It is also used as a desiccant for lithographic inks, varnishes, paints and linoleum, as well as in storage batteries, e.g., nickel-cadmium (Ni-Cd) and lithium-ion (Li-ion) rechargeable batteries (Kang et al., 2010). Cobalt sulfate is employed as a coloring agent in ceramics, enamels and glazes to prevent discoloration and as a copigment for the decoration of porcelain. In addition, cobalt sulfate has been used in animal feeds as a mineral supplement (Budavari et al., 1996; Kirk and Othmer, 1999).In the past, brewers used cobalt sulfate to prolong the life of beer foam (Kesteloot et al., 1968). Ranchers have dosed livestock with cobalt sulfate or used fertilizer enriched with this mineral to ensure that their animals obtained sufficient amounts of the trace mineral, which is essential to the production of vitamin B12. Cobalt sulfate has also been used in veterinary medication to prevent and treat cobalt deficiency in ruminants, which causes a reduction in feed intake and body weight, accompanied by emaciation, anemia and debility.Cobalt sulfate is a water-soluble bivalent cobalt salt. Cobalt sulfate heptahydrate dehydrates entirely at 420° C, and the dehydrated salt forms red monoclinic crystals."

Jan 1, 2015

By Werner T. Meyer

Technical modification of traditional zinc- and lead-based products is moving the metals into diversification is particularly apparent in two areas. The evolution of diverse types of heavy-duty vehicles that employ lead acid batteries. and The development of Galfan™ -- a zinc / 5% aluminum/mischmetal coating alloy designed to provided zinc-coated anti-corrosion protection in applications that are not well suited to traditional galvanizing. Because any product breakthrough must be accompanied by advancement and customer oriented thinking at every step in the chain of production and distribution, a concerted effort is required for market evolution to live up to its potential. As such, all those involved in the metals industries should not only track the progress made by technical and marketing innovations, they must participate as much as possible in their development and promotion.

Jan 1, 1986

By Leo Langland

One of the primary functions of the Geotechnical Services-Materials section of the Arizona Department of Transportation (ADOT) is locating, sampling, and evaluating potential aggregate deposits throughout the State. This information is essential in designing, estimating, and bidding highway construction projects. The nature of materials used for aggregate varies greatly within Arizona. The northeastern or plateau section is famous for its scenic sedimentary formations that are, how- ever, too soft to make suitable aggregate. Volcanic materials are widely used in place of more conventional geologic units. In contrast, the southwestern, or Basin-and-Range section, contains a relative abundance of good aggregate, especially a diversity of gravels. The paper will review the off ice, field, and laboratory methods used by the ADOT Materials Section in satisfying its needs for aggregate information in Arizona.

Jan 1, 1987

By Greg Barfoot, K. Payne

Condition monitoring of conveyor belting has become an established tool for maintenance programming, replacement strategies and quality assurance for belt conveyor systems. What is less well known is that the condition of the conveyor belting is usually a symptom of problems in other areas rather than the problem source. This paper presents an overview of the state of the art in belt monitoring and the move towards on-line NDT systems. The use of belt monitoring data as an indicator for overall system design, maintenance and operation is also discussed.

Jan 1, 1996

By Anthony J. Peach

With the new generation of so called "Super TBM", we would all expect to witness the implied super-performance. In some instances this is occurring, but one must ask why is it not occurring in the majority of applications? For hard rock TBM related projects, we are observing a decrease in the volume of projects in the previously traditional areas such as North America and Western Europe and an increase in Asia (Hong Kong, Indonesia, China, Korea etc). As a consequence less experienced contractors are acquiring the latest ultra high power equipment, without the knowledge necessary to achieve optimum performance. The interdependence of TBM and muck removal systems has been assessed with emphasis on the emergence of the continuously extending conveyor technology, as a means of achieving dramatic productivity increases. The Australian system assessed here at the time of drafting this paper holds the world record tunnel excavation production of 2,166 metres. A little considered aspect of the adoption of conveyors is the associated improvement in safety.

Jan 1, 1995

By William C. Cox, Ronald E. Heuer, Jean-Michel Loignon

The Gatineau shaft described in this paper was an excavation of about 38 m diameter and 21 m depth constructed in Gatineau, Quebec, across the Ottawa River just north of Ottawa, Ontario. A large sewage lift pumping station-was to be constructed in this excavation. Subcontractor for the shaft excavation and initial support was Beaver Underground Structures Ltd., of Dorval, Quebec. Mr. William C. Cox of Beaver conceived the idea for the support system used in this excavation, and was responsible for the construction activities. Initial analysis and design concepts for the lining system were developed by Mr. Ronald E. Heuer. Detailed lining design and construction monitoring were the responsibility of Mr. Jean-Michel Loignon. Geologic conditions indicated by two borings within the shaft area are illustrated in Fig. 1. The shaft excavation would be in the sensitive Leda silty clay. The clay is of stiff to very stiff consistency, with an insitu vane shear strength averaging about 115 KPa (2400 psf) and a reported low value of about 87 KPa (1820 psf). Low strength values were from the middle of the clay layer, with higher strengths at the top and bottom. Average shear strength at the level of the base of the excavation was about 137 KPa (2860 psf). Remolded vane shear strength averaged about 20 KPa (420 psf), with a reported low of 13 KPa (270 psf). Based upon average strength values, the clay sensitivity is 5.8. The clay has an average water content of 53% (range 43 to 66%), which is near its liquid limit (average 56%). The clay unit weight is about 1760 kg/m3 (110 pcf). Underlying the shaft site at shallow depth is limestone bedrock within which the piezometric head is approximately equal to the original ground surface elevation. For shaft support, a -cast-in-place concrete wafer system was considered, but was discarded because of time restrictions imposed by concrete placement and curing. The support system selected utilized liner plate with light steel walers closely spaced. The light rib

Jan 1, 1983

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calcula¬tions where the compliance limit of lbs S02/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equa¬tions to blend to an SO2 content of 1.2 lbs S02/million Btu; the excess sulfur for Coal A was defined as Sulfur excess%o = 0.5 - 0.6-13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C<- 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: ? W is the total weight; ? A, B and C are the fractional proportions of each potential blend stocks; ? Sa, Sb and Sc represent the percent sulfur content of the blend stocks; ? Ha, Hb and He represent the calorific content of the blend stocks in Btu/lb; and ? H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1997

Capital budgeting and investment analysis have, to this point, been beyond the scope of this text. However, a recent conceptual development by John K. Shank and Vijay Govindarajan in the capital budgeting literature is of interest to operations managers because it (1) employs some of the cost management tools outlined earlier in this text and (2) provides a useful framework for using cost management techniques to improve the competitive position of the firm. ft Shank and Govindarajan present a method of analyzing proposed expenditures that is not based on discounted cash flow measures. Their approach employs a combination of three analytical tools: value chain analysis, strategic positioning analysis, and cost driver analysis. In each of these, cost and revenue information is used in ways normally not associated with conventional budgeting. Using this framework, capital projects are selected based on their ability to improve the firm&apos;s strategic position. Shank and Govindarajan have termed this approach "strategic cost management."

Jan 1, 1999

By G. Mike Bernard

The Andacollo gold mine is located near the town of Andacollo (population 14,000 people) in Chile’s region four. It is about 56km (35 miles) by paved road from the coastal city of La Serena. Santiago is about480 km (300 miles) south. Site elevation varies between 1,000 and 1,280 m(3,300 and 4,200 ft). The climate at the Andacollo site is moderate but arid. Average annual rainfall is only 130mm (5 in.). Because there is little rain and the temperature varies only a few degrees (14 to 24 C or 57 to 75F), there are no problems with freezing, solution dilution or pad saturation. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By J. M. Mutmansky, Y. J. Wang

The method usually used to predict the direction of flow in a connecting airway is to conduct a survey of the two existing nodes to be connected by the new pressure airway. It is then assumed that the air will flow from the node with the measured higher pressure to the node with measured lower pressure. This paper examines this direction-of-flow problem using properties of the system characteristic curve for a two-terminal network and specifies some conditions that will ensure that the air will flow in the direction anticipated. It was concluded that the only requirement is that all characteristic curves of the fans in the network should be strictly decreasing. Five numerical examples illustrate some important proper- ties of the direction-of-flow problem.

Jan 1, 2000

By Fathi Habashi

THE MOST important arsenic minerals are shown in Table 6-1. The recovery of arsenic from arsenic sulfides is treated in Chapter Four. Arsenical ores may be either leached directly, or first smelted to volatilize as much arsenic and sulfur as possible, and the resulting product, called speiss, is then leached. A speiss is mainly a complex mixture of metal arsenides, but its [Table 6-1. Arsenic minerals. Arsenides Niccolite NiS Smaltite CoAs2 Skutterudite CoAs3 Sulfarsenides Cobaltite CoAsS Enargite CuaAsS4 Arsenopyrite FeAsS Arsenic sulfides Realgar As4S4 Orpiment As2S3] composition varies widely, depending on the type of ore treated. A speiss usually contains 15-35% arsenic. Methods of leaching are describedd in the following paragraphs.

Jan 1, 1970

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By Joseph Alexis

Humphreys Engineering Co. has been associated with mining and milling since the turn of the century, but its greatest contribution to the industry was development of the Humphreys spiral concentrator in 1943. Few devices in the history of mineral beneficiation have been so uncomplicated. The spiral concentrator has no moving parts and requires no power except that needed to deliver slurry to the feed box, a requirement common to all concentrating devices. Although Humphreys Engineering Co. produces several models of spiral concentrators, the one -commonly used for coal cleaning is Model 24C-6 which has a flatter pitch than most other models. The spiral concentrator consists of a spiral conduit with a modified semicircular cross section. A slurry containing 20-35% solids by weight is fed to the feed box at the top of the spiral and flows downward. The heavier refuse particles concentrate along the inner side of the slurry stream and the lighter coal moves to the outside. The coal spiral has six complete turns-each turn consists of three 120°-sections and each section has a refuse port at the lowest point of the channel. The Humphreys spiral concentrator separates minerals in accordance with their physical properties (primarily specific gravity and particle shape). Aside from pumping slurry to the distributor, no energy is required to produce clean coal since the separating action is controlled by gravity. As slurry flows down the spiral channel, each particle is subjected to a centrifugal force, tangential to the channel. This force piles slurry on the outer rim of the spiral until the flowing stream reaches an equilibrium between outward centrifugal force and downward gravitational force. Once established, the stream position is relatively constant. In any flowing stream, differential velocities are present within that stream (the slowest fluid levels nearest the channel surface and the fastest layers at the center). As the channel curves, the lower slurry levels, retarded by friction, have much less centrifugal force and tend to move sideways toward the inner radius of the channel. As the bottom layers move inward along the bottom of the channel, the upper layers must move outward to maintain equilibrium. This cross sectional rotation separates the minerals and moves those of highest specific gravity toward the inner radius where they drop through refuse ports (see figure on following page). The simplicity of the spiral concentrator is apparent in operation. After tonnage, slurry volume, and percent solids of the feed have been determined-generally with laboratory testing-the operator&apos;s main concern is simple adjustment of the splitters located in the refuse ports. These splitters control the amount of refuse collected and, generally, once properly set they need little attention unless grade conditions drastically change or trash builds up and hinders laminar flow. Spiral concentrators are not overly sensitive to changes in pulp densities, variances in grade, or parti¬cle size and shapes. All these conditions may fluctuate over fairly wide ranges without adversely affecting recovery and product grade. In certain applications, desliming may improve recovery.

Jan 8, 1980

With the rapidly growing use of hydraulics in mining equipment, maintenance personnel should be familiar with the various components in hydraulic systems. Hydraulic systems do wear out - the fluids they transport are hot and turbulent, the equipment they power often imposes tremendous pressure pulsations and bending stresses, and the working environment is harsh. Therefore, even though hydraulic hoses are made of remarkably trouble-free components, they do need to be replaced periodically. There must be coupling methods that allow hoses to be replaced without disturbing other components. Couplings must also provide a variety of leak-resistant connections between hoses and other components in the hydraulic circuitry. Threaded Connection and Seals Hydraulic coupling thread ends and sealing arrangements are standardized, with many types available. Their outward appearance varies, but coupling configurations are recognizable by examining threads and seals and comparing them to the examples provided here. Iron Pipe Thread There are two kinds of iron pipe threads normally used in mining equipment circuitry - National Pipe Tapered Thread for Fuels (NPTF) and National Pipe Straight Thread Mechanical Joint (NPSM). The NPTF seal is the engagement of the coupling threads, called thread interference. When tightened, the tapered thread of the male fitting binds into that tapered thread of the female fitting to form a relatively leakproof seal (Fig. 1). In the NPSM seal, there is a 30° angle seat machined into the end of the male NPTF fitting. This seat engages with a mating 30° angle cone on the inside of the female fitting. Female NPSM fittings have straight threads, as opposed to the tapered threads of the NPTF fittings. However, most NPTF solid male fittings also have a 30° angle seat enabling them to be used with NPSM female fittings (Fig. 2). JIC and SAE Fittings Joint Industry Conference (JIC) and Society of Automotive Engineers (SAE) seals are formed by joining two mating, conical metal surfaces. The coupling threads are used to bring and hold these surfaces together to form a leak-resistant seal. A JIC connection is a solid male threaded end, with a 37° machined male nose, mating with a 37° female flare seat. When connected, the mating surfaces are held together by the threads, but the threads do not form the seal. The female seat is created by flaring a tube end or machining the interior surface of a stem to 37°. A female JIC has a swivel nut, allowing the sealing surfaces to be joined together without twisting a hose or twisting the seats against each other (Fig. 3). JIC couplings are frequently used on low, medium, or high pressure hydraulic circuits on mining equipment and machinery. The SAE connection is similar in appearance and sealing characteristics to the JIC system, except the angle of the machined male nose and female flare seat is 45° (Fig. 4). "O" Ring Fittings Seals for "O" ring fittings are formed by compressing an "O" ring against an exposed machined surface on a mounting block or hydraulic component part. The "O" ring must be compatible with the type of hydraulic fluid used (Fig. 5). An "O" ring boss connection is made of a male straight thread

Jan 10, 1983

By Frédéric Flament, Daniel Hodouin, Claude Bazin

A control strategy is proposed to meet the following specifications of flotation control: minimize the variations of concentrate and tails grades and recovery while limiting the amplitude of variations of the manipulated variables. The strategy consists of determining future control actions which optimize a performance criterion over a limited time horizon. The desired dynamic behaviour of the controlled flotation plant is specified using reference models. The strategy is tested on a 2-computer plant simulator working in an environment which emulates the industrial conditions.

Jan 1, 1993

By Kunio Hashimoto

The conventional troughed belt conveyor system is the most widely used form of equipment for transporting bulk materials in the world today. The reason is not only because it is possible to transport a great deal over a long distance when compare to other types of equipment but also due to its greater economic efficiency and low initial and running costs. When dry, powdery materials and liquid materials are being conveyed, there are enclosed transport methods such as flow, case, air-slider and pipe line. In addition to features of the belt conveyor, a system employing a pipe line to transport dry powdery and liquid materials has always been considered an ideal method. This has been brought into reality through the Pipe Conveyor Sys tem.

Jan 1, 1984

By Richard H. Adams

INTRODUCTION With the discovery and depletion over the years of near surface ore bodies, exploration targets are tending to be at greater depth or overlain by various types of overburden which in some cases extends to considerable depth or is heavily water bearing. Access to these types of deposits for exploration and development often requires vertical shafts. This paper discusses the concept of small shaft engineering and construction, primarily for underground exploration but also for use as a low tonnage production facility or for mine ventilation. The option of a small shaft may be attractive in a number of cases, some of which are: The underground exploration of a deposit at depth where minimal expenditure is desirable until the potential of the deposit has been determined. The exploration shaft in many cases later serves as a ventilation way and second means of egress. Production of ore in a small tonnage/high-grade operation where decline access is impractical. For ventilation where other types of openings are impractical or would delay start-up of mine operations.

Jan 1, 1987

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015