Search Documents

By D. D. Snyder, J. D. Bode, F. T. King

INTRODUCTION Only in recent years have the environmental hazards associated with mining and tunneling operations been fully acknowledged and determined remedial action undertaken. The nature of these excavation operations leads to a wide diversity of hazards spanning mechanical, electrical, chemical, environmental, and physiological. The most insidious of these are unquestionably the environmental ones which have the greatest long-term effect and are the most difficult to pinpoint and monitor. It is the atmospheric contaminants that lead to a significantly greater illness and mortality rate among miners. Dust is the most prevalent, hence most important of the atmospheric contaminants. Respirable particles lead to diseases characteristic of many mining operations: coal workers pneumoconiosis, asbestiosis, silicosis, talcosis, anthrocosis, etc. But toxic and suffocating gases can be equally insidious and the most innocuous pollutant, methane, leads to the most imminently disastrous results of all - explosion and fire. This means that truly effective monitoring of the environmental hazards in tunneling cannot be limited to a few simple standard check measurements. It must include the most precise measurements we can make for specific, documented hazards and even for factors, such as noise and heat stress, not immediately obvious as hazards. The Federal Metal and Nonmetallic Mine Safety Act and more recent Occupational Safety and Health Administration standards are clearly designed to match such effective monitoring. We must, therefore, consider not only presently available monitoring instruments and those currently under develop-

Jan 1, 1997

By F. J. Bruey

Refdist is a simple but valid approach to planning or analyzing a test-vs-control plant trial that uses accumulated plant performance data to calculate objective criteria for judging the trial outcome. Refdist calculations and results are explained and illustrated with data typical of the mining industry. Findings from a simulation study of Refdist statistical properties are reported. Suggestions for dealing with messy data situations are offered.

Jan 1, 1999

By J. Peterson, R. Michael, D. Yantek, E. Ferro

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. To address this problem, the U.S. National Institute for Occupational Safety and Health Office of Mine Safety and Health Research (NIOSH OMSHR) conducts research to reduce the noise emission of underground coal mining equipment, an example of which is the roof bolting machine. Field studies show that, on average, drilling noise is the loudest noise that roof bolting machine operators would be exposed to, and it contributes significantly to the operators’ noise exposure. OMSHR has determined that the drill steel and chuck radiate a significant amount of noise during drilling. OMSHR and the Corry Rubber Corporation (CRC) have developed a bit isolator that breaks the steel-to-steel link between the drill bit and drill steel and a chuck isolator that breaks the mechanical connection between the drill steel and the chuck. This effectively reduces the noise radiated by the drill steel and chuck and in turn reduces the noise exposure of roof bolter operators. This paper documents the evolution of the bit isolator and chuck isolator. Laboratory testing confirms that production bit and chuck isolators reduce the A-weighted sound level generated during drilling by 3.7 to 6.6 dB.

Jan 1, 2011

By Sakir Selcuk, Brian Hamilton, Paul Zick

The 1.8 mi (2.9 km) Minneapolis-St. Paul International Airport Light Rail Transit Tunnels and Station project is comprised of the underground segments of the 11.8 mi(18.8 km) Hiawatha Light Rail Transit route in Minneapolis, Minnesota. The 21 ft 2 in(6.5 m) diameter twin tunnels were mined 65 ft beneath one of the busiest airports in the United States using an earth pressure balanced tunnel-boring machine. This paper will provide a project overview, review the major equipment selected, tunnel segment casting, and describe excavation and lining operations for the tunnels and station.

Jan 1, 2003

By Tommy B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores. It is also known for the great vertical range of its major veins - >990 m (>3250 ft). Not as well-documented, however, are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine and volcaniclastic rocks de- posited within the diatreme complex. The ore-gangue minerals were precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate and oxide minerals along with minor base metal sulfides and precious metal tellurides. Wallrock alteration is limited adjacent to veins and is more extensive within hydrothermal and tectonic breccias. Cripple Creek background The Cripple Creek district has a spectacular production history. More than 653 t (21 million oz) of gold were recovered between 1891 and 1959. Early published accounts documented the principal production from narrow- sheeted vein systems (Cross and Penrose, 1895; Lindgren and Ransome, 1906; Loughlin, 1927; Loughlin and Koschmann, 1935). Production also came from spectacular open-space fillings within the Cresson diatreme, also known as the Cresson “blow-out” (Patton, 1917; Patton and Wolf, 1915). Beginning in the mid- l96Os, more modern studies were initiated by the US Geological Survey (USGS) (Gott et al. , 1967, 1969; Kleinkopf et al., 1970) and by universities (Lane, 1976: Dwelley, 1984; Trippel, 1985; Thompson et al., 1985; Saunders, 1986; Birmingham, 1987; Eriksson, 1987; Nelson, 1989; Wood, 1990; Seibel, 1991).

Jan 1, 1992

By Jeff W. Butwell

Mill flotation tailings impounded at the Gooseberry Mine site between 1976 and 1984 were determined to be an economic source of gold and silver recoverable by standard heap leach technology in conjunction with feed agglomeration. Metal recovery at 85 percent Au, 75 percent Ag is attained on properly agglomerated (pelletized) tailings which average 85 percent -75 micron. Because the impounded tailings averaged over 18 percent moisture (32 percent moisture maximum at depth) in place behind the storage dam, the mining method, mixing and agglomeration technique, and materials handling practice were major considerations in making this operation a financial success.

Jan 1, 1990

By Andy W. Stephens, William H. Langer

In Australia and America, encroachment by conflicting land uses, zoning restrictions, and the "not in my backyard" syndrome make it increasingly difficult to access high-quality aggregate resources located near the market areas. Attempts by government agencies in America to protect aggregate resources for future development have met with varying degrees of success. The State of Queensland, Australia, designates aggregate resource areas as Key Resource Areas, which protect the resource and the routes to transport the resource, provide a separation area from incompatible land uses, and indicate the likelihood that the area is free from conflicting social or environmental issues.

Jan 1, 2005

By R. D. Miller, D. W. Steeples

Seismic reflection is a powerful geophysical exploration method that has been in widespread use in the petroleum industry for more than 60 years. This paper addresses some basic principles of the method and its application at depths shallower than 30 m (100 ft). Since 1980, the shallow reflection technique has been increasingly used for engineering and environmental problems, such as mapping bedrock beneath alluvium and delineating intra-alluvial features near hazardous waste sites, detecting voids in coal and karst, defining the top of the saturated zone and mapping shallow faults. New applications will be added with improved resolution and increased cost-effectiveness.

Jan 1, 1994

By R. Gilges

The implementation of effective techniques for meeting the maintenance requirements of the new Utah Copper Division smelter, one of the largest in the Western Hemisphere, is a goal of the smelter management and supervisory personnel. Kennecott's Metal Mining Division Computing Center has been working with smelter personnel to implement a computer program to provide instantaneous access to equipment specifications, maintenance and cost histories, spare parts, preventive maintenance scheddes, etc. for several hundred pieces of equipment. This information will be available to all smelter personnel via visual display terminals. The system will dramatically reduce the time now spent in search of pertinent information required in effectively performing the maintenance functions. It will also be used to analyze practices, detect trends, prepare budgets, and substantially reduce the paper work normally associated with the running of a large and complex maintenance organization.

Jan 1, 1977

By T. Brady, J. Johnson, J. Whyatt, B. Pariseau, M. Stahl

An elastic-viscoplastic material model allows for time-dependent rock mass motion in proportion to excess stress above the elastic limit. The model produces rounded stair-step curves of displacement versus time that are similar to those obtained from recent borehole extensometer measurements made in the central portion of the Ross shaft pillar at the Homestake mine. The work in progress, including two- and three-dimensional finite element analyses using the UTAH2/3 codes, indicates that the model is a step towards more realistic safety and stability analysis, but that inclusion of rock mass damage may be desirable.

Jan 1, 2000

By Klaus Schönert

Experimental investigations of single particle and interparticle breakage show that the microprocess in mills demands an energy input between 1 J/g and 10 J/g, if particles below 100 pm have to be comminuted. A system analysis of grinding media and roller mills is given in respect to the energy supply to the microprocess and the influence of the back stream caused by the compression of the material inside the active volume. The back stream diminishes the probability for capturing the particles in very fine grinding processes. Some possibilities are discussed how to solve this problem.

Jan 1, 1989

By J-P Franzidis, M. C. Harris

Increasing costs, falling grades and a low gold price have caused severe problems for many of South Africa's gold mines. The need to maximise efficiency is extremely urgent. This paper describes the use of column flotation cell s to scavenge significant quantities of additional gold from flotation plant residues; in particular, very fine particles of free gold not recovered by conventional flotation. Experimental gold- specific collectors enhanced gold recovery significantly. The paper also reports the results of other plant trials, carried out on a variety of ores.

Jan 1, 1991

By T. Petrov

This study was performed to analyze the behavior of the blowing curtain face ventilation system modified with a specially designed regulator, called Wing Regulator. The purpose of the regulator is to extend the airflow penetration depth toward the face and allow effective face ventilation at curtain setback up to 13.7m (45ft) from the face. A small scale model of the Wing Regulator was successfully tested in the Mine Ventilation Laboratory at the University of Kentucky. Then a prototype of the proposed regulator was tested in full-scale in mine environment. Series of three dimensional simulations were performed to support this research using validated CFD code. This paper presents results of the performed studies and discuses the advantages of using the Wing Regulator. Presented information relates to the US Provisional Patent Application No 61/818,112.

Feb 23, 2014

By John Rajala

The Otjikoto Gold Mill was commissioned during November–December 2014 as Namibia’s first new gold producer in 30 years. Its operations consist of surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and gold recovery. The initial mill design capacity was 2.5 Mt/a. Its capacity was expanded after nine months of operation to 3.1 Mt/a, and process performance has significantly surpassed design expectations. After startup, the Otjikoto Mill’s throughput and gold recovery ramped up quickly, with both parameters exceeding design after only two months of operation. The robust process performance continued into 2019, with key performance indicators (KPIs) eclipsing design values in almost every aspect of mill operation. The Otjikoto Mill’s gold recovery is exceptionally high, exceeding 98 percent every year following startup, especially considering the low-grade nature of the deposit.

By D. C. Yang, J. Ye

A comprehensive flotation study has been conducted on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University (MTU). The results are compared with those for a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4% to 5% higher recovery and much lower silica impurity than the concentrate produced by up to six stages using a conventional mechanical cell. The results also show that the packed-column flotation process is particularly suitable for the recovery of finer fluorspar particles.

Jan 1, 1993

By Leon J. Jacobs, Kyle R. Ott

This paper discusses design and construction aspects of the tunnel, shaft and station for the Weehawken Tunnel and Bergen line Avenue Station. The project consists of a 1,269 m (4,156 ft) long existing railroad tunnel, which will be enlarged and equipped with a two-track light rail system. The project also includes construction of a deep underground station, with a large shaft connecting the surface station to the below ground station for access and ventilation purposes. Vibration and noise from blasting is a critical community issue and blasting adjacent to two 230-kV duct banks located in the tunnel invert required special blasting procedures.

Jan 1, 2003

By Robert Sutton, Milan Sjaus

Conveyor pulleys are an important and integral component of a conveyor. Conveyors work in sequence to make up conveyor systems. Each conveyor system is only as reliable as its crudest component. If the pulley fails, then the whole material handling system stops. So what is the effect of this downtime? What are the costs of repair? How much are we willing to pay to solve the problem? What should we spend to prevent an unscheduled shutdown? Do we use the technological improvements at our disposal or do we ignore them to satisfy immediate cost savings? This study will focus on the cost of pulleys relative to the total conveyor cost, the cost of downtime, the maintenance costs and the costs for resolution of the problem. Some philosophic and design concepts are injected for illustration and discussion.

Jan 1, 2000

By H. Benedict

For many years, asphaltic lubricants have been used on large open gears. The asphaltic's diluent is essential to thin the lubricant enough to be sprayed. Once the lubricant has been sprayed into place, the diluent evaporates, leaving the asphaltic to lubricate mating surfaces. Recently, this thinner has been changed to non-cancer causing diluents. The gain in safety corresponded to a lesser ability to evaporate. This paper explores how much diluent remains in the lubricant when it has been assumed to be flashing off. Having quantified the diluent in the lubricant, we can then estimate the effect this has on viscosity.

Jan 1, 2003

By T. Brady, J. Johnson, J. Whyatt, B. Pariseau, M. Stahl

An elastic-viscoplastic material model allows for time- dependent rock mass motion in proportion to excess stress above the elastic limit. The model produces rounded stair-step curves of displacement vs. time that are similar to those obtained from recent borehole extensometer measurements made in the central portion of the Ross Shaft pillar at the Homestake mine. The work in progress, including two- and three-dimensional finite element analyses using the UTAH2/3 codes, indicates that the model is a step towards more realistic safety and stability analysis, but that inclusion of rock mass damage may be desirable.

Jan 1, 2000

By G. H. Matthes

Many mines, in particular coal mines, use inclines or slopes as an access to seam or seamlike deposits which outcrop at or close to the surface. In general, from the surface or from a certain depth, inclines or slopes follow the dip of the deposit with length up to 30,000 feet and by that going under an overburden cover of several thousand feet. The common outbye transport system for mine products is the conveyor. Material and men to be transported down into the mine are handled by rope driven systems when the angle of inclination exceeds the employment of locomotive traction. The transport volume can be sizeable and reach 200 to 300 tons of material and 500 men to be handled daily in a medium size coal mine with a production of 10,000 tons ROM.

Jan 1, 1986