Search Documents

By Guy T. Jr. McBride

World food production is not matching the exploding increase in world-population. Since arable land is limited, ways are being sought to increase yields by turning_ to fertilizer. Phosphate, an essential fertilizer ingredient, is undergoing a period of growth unparalleled in history. The United States is at once the world's largest producer of food and of phosphate rock. Both food and fertilizer output in the United States are being enlarged to meet the demands posed by the threatening world food crisis. New phosphate deposits are being developed in Florida and North Carolina to assure the United States' continued preeminence in this vital resource. Large fertilizer complexes are also being constructed with an eye to both domestic and foreign markets. The growth of the U. S. phosphate industry has been characterized by developing technology in the processing and distribution of phosphate raw materials. The trend from low analysis to high analysis materials accompanied by a change from a large number of small fertilizer plants oriented toward the marketplace to a fewer number of large plants located at the raw material source is illustrative. These changes in technology and distribution have also been important factors in the development of new mining areas in Florida, the Western States and North Carolina.

Jan 1, 1966

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By R. L. Grayson, N. P. Reddy, D. A. Kinzler, S. Yuan, W. R. Myers, R. A. Wells

An examination was conducted on the impact of roof conditions and the mining cycle in determining a representative respirable mass concentration at the mid-shearer location on a longwall panel. Multiple personal gravimetric dust samplers, operated at a flow rate of 2.0 lpm, were used at different locations along the face to isolate the concentrations and variances associated with good and bad roof conditions under both the cutting and cleaning mode of operation. The number of samples needed to estimate the population variance at a given confidence level was analyzed. In addition, the statistical analysis showed that the coefficient of variation of dust concentrations at different locations and under different conditions ranged from 0.185 to 0.475, with an average value of 0.283. The estimates of the average dust concentration for a shift and the variance of the dust concentrations were calculated. A total of 48 data points were available for an [a x b] factorial ANOVA (analysis of variance). The estimates of the variance components were determined. The results from F-tests indicated that both the roof conditions and mining operations had a significant effect on the respirable dust concentration. There was no significant interaction effect between mining operations and roof conditions. In conclusion, this study shows that not only should sampling and analytical errors be considered in determining the required number of samples for a good estimate of the long-range exposures of miners, but also fluctuations of concentrations due to mining operations and geological conditions should be taken into account.

Jan 1, 1991

By A. Marabini, G. Belardi, N. Sheau, F. Veglio

The present paper deals with the modelling of a Multi-gravity separator in the treatment of chromite fines. A first screening study was carried out by 2" full-factorial experiments in order to check the main effects and interactions among the investigated factors: shake frequency, shake amplitude, tilt angle and washwater flowrate were taken in consideration in the study. Two size fractions were employed in the experimental tests. Successively, considering the factor with larger influence on the Cr203 and SiO2 grade and Cr203 recovery in the concentrate, a further improvement of the experimental design was performed to determine empirical models to describe the behaviour of the MGS in the mineral treatment. The results show how intrinsic interaction among the factors take place, highlighting that an optimization study must be carried out considering all the MGS setting parameters.

Jan 1, 1995

By L. R. Shotwell, C. F. Voss, R. J. Bastian

Pacific Northwest Laboratory (PNL) currently supports the U.S. Department of Energy's Office of Civilian Radioactive Waste Management in developing and evaluating analytical methods for assessing the suitability of sites for geologic disposal of high-level radioactive waste. The research includes consideration of hydrological, geomechanical , geochemical , and waste package components and the evaluation of the degree of coupling that can occur between two or more of these components. The PNL effort and those of other research groups investing potential waste sites in the U.S. and abroad are producing a suite of computer codes to analyze the long-term performace of the proposed repository sites. This paper summarizes the ongoing research in rock mechanics at PNL involving flow through jointed rock. The objective of this research is to develop a methodology for modeling the coupled mechanical-hydrological process of flow through joints and then attempt to validate a "simple" model using small -scale laboratory test data as a basis for judging whether the approach has merit. This paper discusses the laboratory tests being conducted to develop s joint behavioral constitutive model for the numerical method under development and the modeling approach being considered.

Jan 1, 1986

By G. T. Newell, J. G. Stone, V. M. Mejia

Introduction Advances in drilling have reached a point where large diameter cores can be recovered from "tight," or weakly indurated placer gravels. In such ground, core drilling can provide more reliable data regarding tenor than can be obtained using churn drilling or similar classical techniques. It can also provide metallurgical and geological information that is not available from samples obtained through alternate methods. In 1985, Coastal Mining Co, a subsidiary of M. A. Hanna, and Western Gold Reserves began to review a Tertiary placer deposit owned by San Juan Gold at North Columbia, CA, about 14 km (9 miles) northeast of Grass Valley. The deposit is one of the largest remaining unmined portions of the formerly extensive early Tertiary ancestral Yuba river system. It has been known since the 1850s, has been the subject of much technical literature, and has been the object of at least four previous drilling programs. The eastern one-third of the 6 km (3.7 mile) stretch of the channel between North Columbia and Badger Hill was partially stripped by large scale hydraulic mining in the late 1870s and early 1880s. Mining ceased in 1884 when the Sawyer Decision prohibited further discharge of hydraulic tailings into the Sacramento and San Joaquin Rivers. By that time, about 30 to 45 m (100 to 150 ft) of relatively low grade upper gravels had been removed over some 81 hm2 (200 acres). About 90 to 105 m (300 to 350 ft) of higher grade middle and lower gravels were left at least partially stripped. In 1914, a few churn holes were drilled along a widely-spaced line. In 1938-1939, Selection Trust conducted an extensive drilling campaign to evaluate the deposit. Particular attention was directed toward the partially stripped eastern portion. In 1968, the US Geological Survey drilled three churn holes in the eastern part of the deposit. The US Bureau of Mines conducted experimental mining and drilling in the Badger Hill area. In the late 1970s, Placer Service Corp. acquired a lease on the deposit. Between 1979 and 1984, Placer Service drilled 28 large diameter BADE (a German-manufactured machine) drill holes on the eastern portion of the deposit. The surviving records from the widely-spaced 1914 drilling program are fragmentary and the reported grade not well substantiated. The 1968 holes were drilled for scientific purposes. Again, drilling details are not available. However, detailed records for both the churn drilling program and the BADE program were available and formed the basis for the initial evaluation of the property. Geology The geology of the auriferous Tertiary gravels of California have been described by Whitney (1880), Lingren (1911), and, more recently, Yeend (1974). In general, the Tertiary gravels in the North Columbia area occupy a broad channel cut into pre-Tertiary igneous and metamorphic rocks. The upper, or white gravel is overlain conformably by volcanic tuffs and volcaniclastic rocks. A middle gravel is characterized by the presence of silicified and carbonized wood. A lower blue gravel unit has relatively coarser cobbles and contains a higher proportion of igneous and metamorphic cobbles than the other units. The upper gravel consists of interbedded pebbly sand and silty, or clayey sands with prominent cross bedding. Most of the pebbles are well rounded and consist mostly of white vein quartz and quartzite. The upper unit is moderately well compacted. Exposures in the walls of the old hydraulic mine pits stand at 45° and 50° angles. The gold content of the unit is well below an economic cutoff. The middle gravel - included with the upper unit by Yeend (1974) - is coarser grained, with carbonized wood, and 75 to 100 mm (3 to 4 in.) cobbles of metased-imentary and metavolcanic rocks in a sandy matrix containing abundant lithic fragments. The upper contact appears to be conformable, but the lower portion of the unit appears in places to consist of reworked lower gravels. The unit contains less clay than the upper unit and is somewhat more friable than the underlying lower gravels. The gold content, while somewhat higher than the upper level, is too low to be of ore grade. The lower gravel averages between 30 to 45 m (100 to 150 ft)

Jan 9, 1988

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By Daniel W. H. Su

The ability to predict the effects of longwall mining on topography and surface structures is important for any coal company in making permit applications and anticipating potential mining problems. The sophisticated finite element model described and evaluated in this paper is based upon five years of underground and surface observations and evolutionary development of modeling techniques and attributes. The model provides a very powerful tool to address subsidence and other ground control questions. The model can be used to calculate post-mining stress and strain conditions at any horizon between the mine and the ground surface. This holds the promise of assisting in the prediction of mining-related hydrological effects.

Jan 1, 1986

By R. L. Guerguerian

Hydrostatic trunnion bearings were recently provided on large Semi-Autogenous Grinding (SAG) mills driven by wraparound motors assembled on the head to shell flanges. A conventional SAG mill would have a ring gear driven through one or two pinions. The effects of the magnetic air gap forces from this new SAG mill drive arrangement on the performance of the bearing are discussed. A step-by-step systematic analytical de-sign of the hydrostatic trunnion bearing is presented, followed by a discussion of grinding mill erection requirements to conform with the design. A brief comparison with other bearing types and their response to the effects of magnetic air gap forces are also presented.

Jan 1, 1992

By D. Hodouin

Abstract. Dynamic experiments were performed in a continuous open-circuit 40x40 cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transfer function and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model. a minimum variance controller with constrained input is designed and its performances are compared. by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By A. J. Lynch

For over 30 years the JKMRC has been conducting research aimed at improving the understanding of comminution and classification processes. The result of this research has been the development of a range of comminution and classification models which has been successfully applied in numerous optimization and design studies throughout the Australian Minerals Processing Industry. This paper reviews the current status of our understanding of the mechanisms which govern comminution and classification processes. Outlines of mathematical models of these processes are described together with examples of their application in design and optimization studies.

Jan 1, 1992

By L. Shevenell, L. Stillings

The Acid Drainage Technology Initiative-Metal Mining Sector (ADTI-MMS) has established a Pit Lake Committee to enhance the science and understanding for the long-term management of pit lakes. Participation in this new committee is from members of federal and state agencies, industry, and academia, including numerous individuals representing 10 states. Work has begun on a pit lake literature search and review, database, classification, and sampling and monitoring procedures document. Coordination with the International Network for Acid Prevention (INAP) has been established. Future work will include preparing a prediction and assumption verification document, a report identifying variables upon which water quality is dependent, and an applied remediation technologies document, including an evaluation of the effects of backfilling.

Jan 1, 2002

By Silas Li, Michael Harris-Gifford, Jason Choi, William H. Hansmire

Twin-bore tunnels with a single track in each tunnel are currently the most common subway tunnel configuration. However, a large diameter single-bore tunnel with two tracks separated by a center wall could replace twin-bore tunnels and introduce potential benefits but require necessary modifications to the subway system. In particular, a nominal 40-foot-diameter single-bore tunnel can be considered in lieu of nominal 20-foot-diameter twin-bore tunnels. This paper discusses the benefits and modifications introduced by replacing twin-bore tunnels with a single-bore tunnel, with respect to various elements of the subway related to the tunnel, stations, track, and tunnel systems.

Dec 1, 2022

By W. L. Chen

In the United States hydraulic cyclones have been used for thickening, classification and cleaning in coal preparation plants for many years. The cleaning cyclones presently in use are based on using a "heavy medium", such as a fine magnetite and water pulp. The latest addition to cleaning cyclones is the one which uses ?water only?, or simply called "Hydrocyclone". Just as was the heavy medium cyclone, the hydrocyclones were originated in the Netherlands (1, 2). Plants using hydrocyclones were built in Europe (3) and test plants were erected in Canada (4, 5, 6) and India (7). Roberts and Schaefer Company has built four plants using hydrocyclone circuits. One additional plant is in the process of construction.

Jan 1, 1965

By Robert E. Ennis

The somewhat misnomered "continuous" face section is in most mines today still far from perfect continuity. Achieving uninterrupted flow of coal from the mining machine to the outside has been a long sought for goal. Clearly, the largest problem to be solved in continuous mining today is one of increasing the cutting time of the miner. Full machine utilization can never be achieved with the new high capacity miners, as long as their performance is tied to that of the shuttle car. Figure No. I illustrates the point at which shuttle car haulage distance determines unit productivity rather than the productive capacity of the miner. Continuous mining is never realized. A recent development has proven, however, that truly continuous mining and haulage is possible. The Bell & Zoller Coal Company working with the Research and Development Department of Hewitt-Robins Inc. developed and perfected a new mining system which offers advantages in terms of increased productivity at reduced mining costs and enhances the safety of personnel at the face. This new system involves the use of two pieces of equipment that form a unbroken link, at all times, between the mining machine and the mine belt haulage system. These pieces are a Mobile Bridge Conveyor, and an extensible panel conveyor. The following areas of discussion will be covered during the review of this development. I. The design and operating features of the new system. 2. Its application in underground mining 3. The performance of the system to date 4. Operation and maintenance cost considerations 5. Safety features of the system

Jan 1, 1965

By I. Loomis, D. Rachmad, I. Duckworth

During the past two years the Underground Mine Ventilation Group at PT Freeport Indonesia has undertaken to upgrade their Hygiene Laboratory. This process has included upgrading equipment for dust sampling and gas monitoring, as well as procurement of an OCEC analyzer for Diesel Particulate Matter analysis. While the laboratory equipment represents one factor, these changes have also required re-evaluation of the sampling protocols and the burden of ventilation monitoring personnel. This paper provides a review of these experiences.

Jan 1, 2006

By J. Kalnejais

Discovered in 1896, the Sons of Gwalia orebody was initially mined by unground methods. Euring the mine's uderground operations workings reached a vertical depth of 1080 metres. The same orebody is now being mined by open cut methods. The present operation mines a broad envelope of mineralisation surrounding old stopes, whereas the original underground operation concentrated on mining high grade parts of the Gwalia Lode System. Underground mining continued up to 1963 when operations ceased due to high operating costs and the low grade of ore mined. In 1984 a new company, Sons of Gwalia NL, commenced open cut operations.

Jan 1, 1989

By Farlow C. Davis

Magma Copper Company, San Manuel Division, is a wholly owned subsidiary of the Newmont Mining Corporation and located at San Manuel, Arizona. The ore body is a dessiminated porphry copper deposit in quartz monzonite. The primary copper mineral is chalcopyrite with minor amounts of chalcocite, bornite, and covellite. The molybdenite occurs mainly on fracture faces or else associated with quartz veinlets. Pyrite is the major sulphide mineral in gangue. The feed to the concentrator from the underground mine is approximately 0.720 percent copper and 0.029 percent molybdenite. The concentrator has a design capacity of 62,000 tons of ore daily. After a standard ore treatment circuit consisting of grinding, rougher flotation, regrinding, and cleaning, a bulk concentrate is produced which contains 27 to 29 percent copper and 1.0 to 1.2 percent molybdenite. This concentrate is pumped to the molybdenite plant feed thickener.

Jan 1, 1977