Search Documents

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011

By J. Villeneuve, G. Fourniguet

Simulation of Mineral Processes is now commonly used by the Engineers in charge of plant design or optimization but a good knowledge of the simulation tool is still needed to conduct a project. A new level of algorithm has been defined above the simulator to answer directly to the user's questions. This level has been called the supervisor of simulation, which is using the automation concepts of sensors and actuators. At any place of the flowsheet (i.e., a stream or an equipment), the user may indicate which value could change by graphically implementing an actuator. Then, he can evaluate the effect of the variation of this value at any other place of the flowsheet by inserting a sensor. Thus, by example, it becomes possible to look at the evolution of the recoveries and/or the circulating loads when scanning an interval of the possible teed flowrates. This approach conducts to an increased facility in using a simulator and in analyzing the predictions. It is also a very valuable tool for permitting to characterize the sensibility of the simulation results to the variation of some settings (e.g., load of grinding media, rotation speed, water addition, etc.) or feed characteristics (e.g., flowrate, sizes, grades, grindability, etc.). Thus, the most important variables can be identified for design and pre-control optimization of plants. This new level of simulation will be implemented in a further version of the USIM PAC simulator and selected examples are presented.

Jan 1, 1995

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents the preliminary test results obtained using a 0.38-kg/s (3,000-lb/hr) beta prototype MagMill. In processing Upper Freeport coal, the beta prototype recovered 82 % of the weight of the feed and 91 % of the heat content while reducing the potential emissions of sulfur by 61%. Pyritic sulfur in the MagMill product was reduced by 78% compared with that in the feed. For all runs, the mill product particle size was controlled to between 70% and 80% -741m (200 mesh). Recoveries of mercury, arsenic and selenium ranged from 35% to 45% of the amounts found in the feed. Power draw was reduced by 26%, and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2002

By James J. Olson

INTRODUCTION The need for Government-sponsored research and development to increase excavation rates and lower costs for tunneling and mining operations in a variety of rock types has been emphasized in a wide range of publications from advisory panels, symposiums on rapid excavation, and individuals. In response to the predicted demands for mining and construction-oriented underground excavations for the next two decades (1970-1989), a comprehensive 10-year, $200-million research program in rapid excavation was proposed by the National Academy of Sciences in 1968 (1). Although the large program recommended by the Academy has not been funded, substantial Government-sponsored research in rapid excavation has been conducted during the past several years. This paper reviews some of the significant research accomplishments obtained under a three-year, $6.6-million research program in rock mechanics and rapid excavation sponsored by the Defense Department's Advanced Research Projects Agency (ARPA) and managed by the Bureau of Mines. In addition to the rock mechanics research, five major phases of excavation; systems analysis, geologic prediction, rock disintegration, ground support, and materials handling were represented by the projects funded under the ARPA program. The brief outline below recapitulates the major research areas and some of the projects summarized by this paper: Excavation Process Modeling by Computer Geologic Prediction Geologic Reconnaissance for Site Selection Longhole Probe Drilling for Hazard Detection

Jan 1, 1974

By Igor Gonzales G.

Southern Peru Copper Corporation (SPCC) has recently completed the construction of copper leaching, solvent extraction, and electrowinning facilities at their Toquepala and Cuajone plants in Southern Peru. Much of the ore for these new operations is the result of the existing mining operations that have been in existence as early as 1959. At Toquepala, pre-conditioning and bacterial dump leaching of the sulfide ore that was too low in copper content to be processed through the copper concentrator began in 1987. The Cuajone heap leach operation is treating copper oxide ore that has been stockpiled since the Cuajone concentrator began operation in 1976. The pregnant leach solutions from the dump leaching at Toquepala and the permanent pad heap at Cuajone are combined into one plant feed solution. Adjacent to the large dumps at Toquepala, a solvent extraction and electrowinning facility has been constructed. The electrowinning facility has a planned annual production rate of35,000 metric tons per year Grade A cathode copper. Initial production of the cathode copper began in November 1995.

Jan 1, 1996

By Richard A. Bideaux

During 1977 and 1978, a comprehensive study was made of the drill-hole data obtained by Urangesellschaft, USA, from their Juniper Ridge, WY, uranium deposits. This included uranium grade data acquisition, application of a variety of mineral deposit modeling techniques, and estimates of minable reserves, which pointed towards a possible production decision.

Jan 1, 1979

In this paper, the logic and the capabilities of a long term production planning method for open pit mining are presented. The method is the first attempt in obtaining simultaneous solutions to the four interrelated parameters of open pit mining; 1) the mine life, 2) the specific blocks to be mined each year, 3) the amount of ore and waste to be mined each year, and 4) the ultimate pit limits. An efficient cutoff grade can also be obtained through a sensitivity analysis. None of the existing methods can bring such a comprehensive solution to the problem. A production plan for a real life gold deposit is given to illustrate the logic and the capabilities of the method.

Jan 1, 1993

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By J. J. Gusek, J. T. Gormley, V. Scovazzo

Glenrock, WY is underlain by two abondoned coal mines. Subsidence events have been recorded over the years, with the frequency increasing in recent years. As part of Wyoming&apos;s Abondoned Wins Lands Program, investigations including mining history/methods/mappings, subsurface drilling and material site searches were performed. Portions of the mines less than eighty feet from the surface, were identified as probable for subsidence. Subsidence control by hydraulic backfill was selected. Design included search and injection boreholes, water supply from the mines and the slurry mixing, transport and injection system. Injection system performance and backfill success is king monitored during construction.

Jan 1, 1986

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By K. Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1993

By G. M. (Frits) Swinkels

The Apex property, mined in the early Twentieth Century for direct shipping copper, also contains gallium and germanium in iron oxide minerals. In 1982, Musto Explorations Limited began an exploration program to define reserves. A metallurgical process was developed, and a production decision was reached in late 1983. This text describes the process development and design. The Apex mine, located near St. George in Southwestern Utah is owned by St. George Mining Corporation, a subsidiary of Musto Explorations of Vancouver, B.C. Musto acquired the property in early 1982. A pilot plant was operated by Hazen Research, Inc., Golden, CO later in 1982. In late 1983 sufficient information had been developed for St. George to proceed with the project. The final process design was prepared by G. M. Swinkels of Vancouver, consultant to Musto, and Hazen Research. Process engineering was done by Hazen Research, and St. George acted as its own contractor. Commissioning of the plant began in October 1985.

Jan 1, 1986

By Robert Moore Lewis

Extensive exploration is being undertaken throughout the world in search for heavy minerals, particularly rutile and other titanium minerals. The federal government is sponsoring research involving rutile ores and recovery of stockpile-grade concentrates from domestic sources. Producers are being forced to turn to deposits with a heavy mineral content as low as 0.50% (essentially rutile and zircon). The North Carolina State University Minerals Research Laboratory investigated the possibilities of recovering heavy minerals from the amine tailings of the Texasgulf Inc.&apos;s phosphate plant at Aurora, North Carolina. One laboratory beneficiation procedure using gravity, electrostatic and magnetic processes, resulted in the recovery of 78.7% of the heavy minerals in the amine tailings. Based on this percentage recovery and the present rate of phosphate mining, approximately 13,000 tons per year of heavy minerals (principally ilmenite and zircon) with a potential value of approximately $1,045,000 (1977) could be recovered. The economic potential for recovery of these heavy minerals appears to be favorable. A flotation procedure for up-grading the heavy minerals content in the amine tailings has been developed at the Laboratory, which could allow for concentration of heavy minerals and storing them in tailings area other than main tailings for future processing.

Jan 1, 1978

By Reinhard Gertl, Soroush Dabiri, Juan-Carlos de Rueda

The Tunnel of Guillermo Gaviria Echeverri, spanning 6.05 miles, will be Latin America’s longest road tunnel, is currently under construction in Colombia’s Antioquia Department with a single bidirectional tube connected to a parallel rescue tube through multiple cross-passages. The study faces challenges in implementing the prescriptive semitransversal ventilation system due to design restrictions. Different ventilation concepts are eplored to nd the most suitable system for regular operation and re scenarios. A quantitative ris assessment evaluates each alternative system and identies the longitudinal ventilation system, accompanied by ris mitigation measures, as the safest choice, since it surpasses the prescribed semitransversal ventilation concept.

Jun 23, 2024

By R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance is reviewed.

Jan 1, 1999

By S. C. Torma

Sources of lead contaminated soils are numerous, i.e., the uses of leaded gasoline, lead-based paints, leaded pesticides, solders, smelting of lead concentrates, refining of lead products, automobile demolition, recycling of lead batteries, and so on. Conservative estimation by the US Environmental Protection Agency, EPA, indicated that several thousand lead contaminated sites are awaiting remediation. The current remediation technologies include immobilization, reclamation and soil washing. In this paper, the above remediation technologies will be reviewed, and where appropriate, the economics of processes discussed and future possibilities indicated.

Jan 1, 1996

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

By George F. Swindle

This paper discusses a composite of two coal reserve studies, each of which made use of a computer-based modeling system to assist in an evaluation of multi-seam deposits. The model permitted simultaneous consideration of seam thickness, seam structure, overburden thickness, over-burden ratio, and quality parameters for sulphur content, ash content, BTU values and the EPA Compliance index. The model is designed for use by a non-programmer, geologist or mining engineer. It enables the user, from a computer terminal in his office, to specify constraints (for example maximum um sulphur and maximum- ash content, minimum seam thickness and minimum BTU rating), and produces a report showing the volume, quality and location of that part of the total in place deposit satisfying all the constraints.

Jan 1, 1983