Search Documents

By L. J. Laughlin

The majority of non-drive conveyor pulleys use rotating shafts, and typical idler rolls use non-rotating shafts, even though both products are used to support and guide the conveyor belt and its load. This paper will explore and compare the requirements for rotating and non-rotating shaft designs and the impact of that design on the product. Additionally, it will explore how the “roller” bearing types (deep groove ball, tapered, or spherical) affect these designs.

Jan 1, 2003

By K. C. Ko, M. D. Bunnell

The studied coal mi1e is an underground coal mine located in the northern Wasatch Plateau of central Utah (Figure 1) . Since operation began in 1981, in situ stress conditions have been encountered which differ from the assumed conditions utilized during early mine design efforts. Geologic structures also varied somewhat from those projected during initial geologic interpretations of the area. The encountered geologic conditions combined with the unusual stress conditions prompted a combined study of in situ stress and stress-related geologic structures. The study was conducted in two phases, with phase 1 consisting of detailed underground mapping and analysis of stress-related geologic structures to determine stress orientations from which they originated; and phase 2, consisting of over- coring two sites within the mine to determine present in situ stress orientations and magnitudes. GEOLOGIC ANALYSIS Three types of geologic structures have been encountered in the mine that act as indicators of stress orientations of the geologic past. Two of these structures, faulting, and igneous dikes, are directly measurable in the mine. A third type of structure, photolineation, was detected through remote sensing methods and shoe god correlation to roof conditions in certain areas of the mine. Faults Two major orientations of faulting have been encountered in the studied coal mine, including a system of N 80 W striking normal faults and a system of N 55 to 70 W striking oblique-slip faults. Only data collected from the oblique-slip faults were used for this study due to the fact that these faults offset the N 80 W faults wherever the two systems intersect, indicating that the N 55 to 70 W system was created by a more recent stress field. Figure 2 shows locations within the mine where data were collected from seven locations along oblique-slip faults. Data collection consisted of measurement of fault plane strike and dip, fault slickenside trend and plunge, and slip direction. The data are tabulated in Table 1. The fault data were then plotted on stereo nets to determine the stress orientations present at the td of faulting (Figure 3). The determined stress orientations are 32~0 included in Table 1. The stereo net plots show average principal stress orientations of: 1) [ ] plunge 1 degree. These data suggest that the N 55 to 70 W oblique-slip faults were produced by a nearly

Jan 1, 1986

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023

By J. B. Hiskey, V. M. Sanchez

Electrochemical oxidation of arsenopyrite (FeAsS) has been investigated as an attempt to gain a better understanding of its dissolution chemistry. Rest potential measurements, cyclic voltammetry and constant potential experiments were conducted in the pH range from 8 to 12 in the absence and the in the presence of cyanide. A two-step reaction sequence is suggested by the electrochemical measurements. The initial step is described by: [FeAsS+6H20=Fe(OH)3+H2AsO3- +S°+7H++6e] The second step involves the oxidation of the arsenite and sulfur according to the following reactions: [H2As03-+H20=HAsO24-+3H++2e and S° +4 H2O=SO4-+3H++6e] Stoichiometric determinations confirm that 14 electrons are involved in the overall reaction.

Jan 1, 1992

By G. Bloomsburg, R. E. Williams, S. D. Vincent

A modeling scheme is developed to simulate the hydrogeologic effects of mine design and development in unsaturated rock. Simulations are conducted using the UNSAT2 finite element computer program and hydrogeologic data from the site of a proposed mined-out waste repository at Yucca Mountain, NV. Results of the simulations are analyzed for: •variations in the direction of ground water flow and in the distribution of pressure head caused by the design of the mined out openings; and •mine design variables that affect the predicted rates of mine water inflow. Evaluating the hydrogeologic impacts of mine design and mine development in unsaturated rock is significant in several respects. Characterization of the preemplacement of wastes along the fastest path ground water flow system at the Yucca Mountain site has been a primary research effort. Ultimately, however, the degree to which waste isolation is achieved will depend largely on the post-mining hydrogeologic environment as altered by the mine design and on the radionuclide inventory and resulting heat effects of the repository. Therefore, an ongoing characterization of the proposed mined-out nuclear waste repository at Yucca Mountain, NV, is recommended. Modeling results indicate that: •mined out openings will affect the movement of ground water, both in rate and direction; •hydraulic effects of mine development depend on the hydrogeologic environment and on mine design geometry; •mine water inflow is possible in the unsaturated zone, even for mines developed in hydrogeologically homogeneous rocks; and •mine water inflow can occur at values of down ward flux that are appreciably less than the saturated hydraulic conductivity of the overlying rocks.

Jan 1, 1991

By Bruce Johnson

This paper is not written to "break new ground" in computer applications; it is just a treatment of how an operating metal mine utilizes a mainframe computer for planning, analyzing, and reporting on the ventilation and cooling systems. The Unisys mainframe computer at the mine site is used in programs that analyze the ventilation network, keep records on various ventilation installations, calculate the results of measurements and produce reports on ventilation conditions in the working places and on the main air distribution, and plan and analyze the cooling system. All the programs are interactive to terminals. There are a series of data files that are generated by some programs which may be used by other programs. Most of these programs have been developed in-house. The computer is also used as a word processor via a vendor-supplied text editing program to produce memos, letters, and to keep up-to-date lists of equipment used.

Jan 1, 1989

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017

By George B. Griswold

The two most stringent parameters for in place fracturing of rock are the lack of any initial void space in the rock which to expand into and the ability to gain access only through drill holes. These two restrictions have proven so severe that as of today the only proven techniques for efficient fracturing are the contained nuclear detonation and hydrofracing. Both of these methods have highly developed technologies for their application. Hydrofracing has been a standard oil field practice for two decades, and the experience gained from a couple hundred underground nuclear detonations has resulted in a thorough understanding of the phenomenology of cavity and chimney formation. What is still lacking is a practical method to create a suit- able degree of fracturing for those ore bodies which do not meet the application criteria for either the nuclear explosion or hydrofracing. Nuclear applications must be restricted to thick ore deposits so as to take advantage of chimney collapse height--preferable in excess of 200 feet thick. Other requirements such as ground shock, containment, and radioactive contamination further reduce the number of sites that prudently can be selected.

Jan 1, 1969

By Barry R. Doyle, James P. Rose, Marius P. Gronbeck

This paper presents a strategy for addressing the hazards of construction of tunnels in ground containing methane. A discussion of the nature of methane includes occurrence underground, and manner of entry into excavations. Means of methane control for underground operations are discussed, including ventilation, monitoring, equipment selection, and personnel training. Principles of ventilation for gas dispersion and removal are addressed. The use of continuous gas monitors, automatic power shutdown systems, and hand-held detectors is discussed. The paper addresses integration of permissible equipment to provide a safe system. Aspects of personnel training are discussed, including maintaining hazard awareness, and evacuation and re-entry procedures.

Jan 1, 1991

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) ammines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Nov 1, 2011

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

1.1 GENERALIZED METHODS OF SUPPRESSING THE INFLOW OF GROUND WATER DURING THE CONSTRUCTION OF SHAFTS, DRIFTS AND TUNNELS Various methods are used to prevent or minimize the inflow of ground water into underground workings during their excavation. The two most common methods include freezing the saturated rock and grouting using cement, sodium silicate, polyurethane and/or other chemicals. Each of these technologies for combatting the inflow of ground water is effective only under specific hydrogeological conditions. For example, although the freezing of saturated ground is among the more universally adopted methods, it is designed to provide only temporary protection during construction. Before the saturated rock thaws it is necessary to emplace a waterproof liner which is labor intensive, time consuming, and expensive. Consequently, freezing is used only in exceptionally complex hydrogeological conditions, namely in those cases where the water-bearing strata consist of unstable rock or the ground water has an anomalous hydrochemistry. The classical grouting of saturated rock, carried out from the surface or from the face of the underground workings for the purpose of limiting the inflow of ground water during excavation, utilizes both cement and a variety of chemical grouts. Cement grouting has been regarded as the main method of combatting the inflow of ground water in fractured rock throughout the world. In such countries as the Federal Republic of Germany (FRG), Canada, the Republic of South Africa and Great Britain, cement grouting is the main method of reducing the inflow of ground water during the excavation of mine openings. In Great Britain and the FRG, cement grouting has been used in 80% of all shaft excavations. In the Republic of South Africa cement grouting has been used in almost 100% of all the shafts that have been constructed. The installation of grout curtains into permeable water- bearing strata significantly reduces their permeability and increases the rock strength. Grouting has the greatest effect in fractured sandstones, certain well indurated shales, fractured granites, fractured quartzites, and karstic limestones or dolomites. The following principal factors must be considered when assessing the expediency of grouting rock with cement: the geometry of the network of fracture openings, the saturated hydraulic conductivity of the fractured rock, the hydraulic head acting on the water in the rock, and the chemical composition of the ground water. On the basis of the geometry of the fractures and the thickness of each hydrostratigraphic unit, the characteristics of the cement grout are selected. As a rule, the cementing of large fractured zones with high ground water velocities is carried out using inert fillers (sand, mill slag, loam, loess, crushed limestone), special types of cement, setting accelerators, and high cement concentrations in water. Calcium chloride, soda ash, sodium silicate, sodium nitrate, amino alcohols, tin bichloride, trisulphate nitrate, and lumnite are used extensively as the setting accelerators for cement grouts. In the FRG and Poland, special cement injection compounds that embody a mixture of cement and active cement metal salts, water additives and binding substances are being used for the cementing of saturated zones with rapid ground water velocities. These reagents accelerate the rate of structure-forming reactions. In spite of the wide variety of additives used for cement grouts, the effectiveness of the method in large fractures below the water table is either poor or it leads to a very large consumption of cement due to the erosion of the grout through the cracks before it hardens. At the present time, a large number of cement types and brands are being produced by various countries. These variations permit cementing to be employed in a variety of geological conditions. However, both pure cement grout and grouts with fillers constitute unstable systems with a high water loss rate. Therefore during the grouting of finely fractured rock the cement grout's premature loss of a large amount of free water causes its consistency to increase, whereupon the grout solidifies. Consequently, it inadequately penetrates into the fine fractures of the stratum. In addition the high water loss rate in the cement grout causes unreacted cement particles to remain, which greatly reduces the grout hardness and the resulting rock strength characteristics are weakened. As a result, the binding properties of the cement are utilized perhaps up to 60%. The remaining portion is left in the grout as a filler. All these conditions significantly decrease the efficiency of the isolation effort both with respect to strength and cost. In order to expand the cement grouting method, re- search is being conducted to improve the quality of cement grout, to increase its range of application with respect to permeability control, to reduce its water loss rate and to increase its capacity to withstand the erosive and corrosive effects of poor quality ground water. For example, mixtures of bentonitic clay, carboxymethyl cellulose, aerated sodium sulfide, sulphated alcohol distillery waste, nitrolignin, gip-

Jan 1, 1993

By J. L. Ellenberger, P. W. Jeran

A deep longwall coal mine was instrumented with a three-dimensional microseismic system in order to help determine the exact strata mechanics associated with the rock failure, redistribution of stress and the associated gob formation from the longwall. Overall, 5,000 well calibrated seismic events were recorded during the mining of the panel. Analysis of these events showed a close correlation between the seismic activity and advance rate, and that the majority of the recorded seismic activity occurs in the immediate area of the advancing longwall face.

Jan 1, 2002

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

4.1 THE GENERAL COMPOSITION AND PROPERTIES OF CLAY-BASED GROUTS Clay-based grouts are visco-plastic systems; they are made by adding structure-forming reagents to a clay mineral mortar. Small amounts of cement and various chemical ad¬ditives constitute the reagents. If necessary, fillers also are added. The distinguishing feature of clay-based grouts is that throughout their entire stabilization period they do not form a crystallized structure as does cement grout. The structure of stabilized clay-based grouts does not deteriorate during minor rock movement or upon the initiation of blast¬ing during the construction of a shaft or a drift. Because they can possess good rheological properties during the ini¬tial structure-forming period relative to cement grouts, clay¬based grouts are not easily eroded from large fractures and karstic cavities by flowing ground water. In addition, their finely dispersed clay particles facilitate a greater fracture penetration capacity, especially in dual porosity rocks. Numerous investigations of the structural-mechanical and rheological properties of clay-based grouts by STG have demonstrated that the most effective grouts for pre¬venting the inflow of ground water into underground work¬ings are grouts that have a cement content of 8 to 10% (90 to 120 kg/m3) of the clay grout by mass. The grout should have a density of 1.18 to 1.30 T/m3. Various additional substances and chemicals can be added as additional fillers and structure-forming reagents. In pure ground water at temperatures above freezing, sodium silicate in the amount of 0.8 to 1 % by mass normally is the only structure-forming reagent that is necessary if the proper clay is selected and if it is available. The production process for making clay-based grout is divided into two stages: 1) the production of an initial clay mortar with specified properties and 2) the production of a clay-cement additive grout mixture using the initial grout along with the structure-forming reagents, including the ce¬ment. The properties of clay-based grouts depend on the phys¬ical-mechanical properties of the initial clay mineral, the properties of the cement and the properties of the chemical reagents that are added. 4.1.1 TECHNOLOGICAL PROPERTIES OF CLAY-BASED GROUTS The dynamic shear stress' To, the viscosity 11, the static shear stress2 0, the maximum shear stress of the structured that the rheological and structural-mechanical prop¬erties of clay-based grouts must fall within the following limits: the dynamic shear stress To = 50 to 200 Pa; the viscosity -9 = 0.02 to 0.07 Pa sec; the static shear stress 0 = 150 to 600 Pa; the plasticity strength Pm of the structure one minute after preparation (according to P.A. Rebinder's method) equals 150 to 500 Pa. The plasticity strength 10 days after preparation is ? 0.15 MPa. The general relationship of the change in the structural strength of clay-based grouts relative to stabilization time is shown in Fig. 32. The figure shows that the structure-form¬ing process for clay-based grouts is characterized by three stages. These stages correspond to the time periods required for conducting the principal operations during the injection of the grout into a fractured aquifer as described below. Stage I, corresponding to the time period T1, reflects the small development of structural strength during early stabi¬lization. During this time, the structural strength must not preclude the capability to pump the grout. The time Tl must correspond to the length of pumping time from the moment water is shut off and mixing occurs until the pump stops forcing the grout through the manifold block and pipeline into the fractured rock as described subsequently herein. Stage II, corresponding to the time interval T2, reflects a sharp but controllable increase in the structural strength of the grout. The length of time period T2 is controlled by the addition of appropriate reagents. Stage III produces the final value of the structural strength. This final strength is used to design the dimensions of the isolation curtain. Consequently, the development of grouts is guided by two principal criteria: 1) the grout must develop the highest possible structural-mechanical properties and 2) it must be able to be pumped by a piston pump prior to final stabili¬zation. Successful grouting depends to a large extent on the correct design of a grout for each specific case. It is impor-

Jan 1, 1993

By Robert W. Miller, Rhoda S. Kriesel

INTRODUCTION With each passing year, the general public becomes increasingly aware of the potential hazards associated with many products and services previously considered unharmful. This new consciousness is especially evident in the workplace, both as the result of advances in scientific understanding and the influx of concerned, responsible professionals into the labor movement. For example, data produced by epidemiologists doing retrospective mortality studies which related mortality to toxic substance exposures has often been the prime motivating factor behind reductions in exposure standards. This certainly has been the historical case with many radiation exposure standards, including the limitations set for "Working Level" exposure. The concept of "Working Level" was introduced in PHS Publication No. 494 as a result of both the difficulty in relating radiation units to biological effects and the complexity of interaction of radon daughters with the physical environment. WORKING LEVEL One working level is defined as any combination of radon daughters in one liter of air that will alternately release 1.7 x 105 MEV of alpha energy during decay of 210pb (RaD). Its usefulness is that working level can be readily measured in both the field and the laboratory. Because of this, existing occupational exposure standards for radon daughters in both the U. S. and other countries use working level as their basis. In the U. S., the last twenty years has witnessed a significant reduction in radiation exposure standards from 120 working level months to 4 working level months per year. New international standards are being proposed that would be only slightly higher than these current U. S. standards. POTENTIAL EXPOSURES TO RADON DAUGHTERS The universal use of nuclear power, along with the transfer of nuclear technology to developing nations, has significantly increased the demand for fuels. As a result, uranium mining operations have expanded and increased numbers of miners are regularly exposed to radon daughters. In addition to potential exposures in uranium mines, other deep mines such as tin, gold, platinum and tungsten, also have potential exposures due to the distribution of uranium and its accompanying radium throughout much of the earth's crust. The energy crisis has also prompted interest in general population exposure to radon daughters in buildings. Many homeowners, using additional insulation and caulking to seal cracks and conserve energy, have reduced indoor ventilation to the point where working level exposure could become significant, especially in homes with unventilated crawl spaces. In fact, several serious exposure situations have occurred where mine tailings were used for building materials. MEASUREMENT TECHNIQUES Historically, rapid and convenient measurement techniques have been actively sought to improve the ability of ventilation engineers to limit mining exposures through ventilation control. A number of measurement techniques have been developed, including the Kusnetz method (further elaborated by Shalaynev) and techniques developed by Rolle and Tsivoglou. All, however, suffer from similar handicaps that prevent their usefulness in the mining environment. Their main limitation, in terms of minimizing employee exposure, is the elapsed time from the start of sampling until the results can be calculated. It is usually 40 to 90 minutes. This time delay presents both serious economic limitations as well as the potential for exposing workers to high radon daughter concentrations until calculations are completed and corrections made. Further reducing the utility of the Kusnetz and Tsivoglou techniques is the need for tedious calculations that increase the possibility of human error along with the need for cumbersome sampling equipment that is not ideally suited to the mining environment. INSTANT WORKING LEVEL METER To alleviate these problems, the idea of an Instant Working Level Meter was conceived by several groups. Several such instruments were proposed, built, and tested with disappointing results. Although the concepts behind them were sound, the instruments simply failed to measure working level without excessive distortion. In addition, their cost was relatively high, gamma background presented a problem, and sophisticated computations were necessary to determine working level. In short, these systems lacked the design engineering that would make them suitable for the demands of a mining environment.

Jan 1, 1981

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type. (1) prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution.

Jan 1, 1978

By Peter J. Huck, Bruce G. Stegman, Richard E. Thill

Introduction Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind backfilling process has been successful for stabilizing ground over abandoned and inaccessible underground coal mines. This article describes the systematic evaluation of potential monitoring systems that would improve backfill monitoring technology. It also details field proof-of-concept tests that were conducted on two systems and the difficulties encountered in implementing them. Ground subsidence over abandoned mines can have devastating effects on overlying urban areas decades after the closing of room-and-pillar mines. The result may be cracked foundations, ruptured gas and water lines, broken sewers, distortion or cracking in superstructures, and sinks and potholes in the ground surface. About 32,000 km2 (8 million acres) of land in the US has been undermined for coal. According to the US General Accounting Office, 8,100 km2 (2 million acres) have undergone subsidence and another 8,100 km2 (2 million acres) are expected to subside by the year 2000. Actual figures on land affected or threatened by subsidence are probably much higher, since these estimates were based on late 1960s studies. For more than two decades, the US Bureau of Mines has been engaged in stabilizing ground in urban areas having high risk potential for subsidence costing millions of dollars. Thousands of acres have been stabilized, protecting property worth hundreds of millions of dollars. In earlier years, backfilling was by in-mine stowing in accessible mines or by gravity-feed sluicing methods in inaccessible mines. Pumped-slurry methods have been used extensively in the past 10 years. More slurry can be injected for fill from fewer injection holes over extensive areas in abandoned mines. Since this method requires fewer boreholes, there is less disruption of surface facilities. An investigation was conducted to determine the feasibility of using advanced, remote sensing or monitoring technology for application in monitoring fill placement. Specifically, the objective was to develop conceptual systems for blind backfill monitoring that require fewer boreholes and give better definition than is now possible. Blind Backfilling Methods Blind backfilling operations are conducted from the surface and do not require personnel and equipment underground. These methods are applicable to abandoned, inaccessible workings. Two categories of blind back-filling are point support, practiced by civil engineers to protect individual structures or surface facilities, and areal backfilling methods, used to protect large areas against subsidence. Point Support Methods Point support methods are usually gravity-feed systems. In general, point support methods use small volumes of expensive fill material and require a large number of boreholes within a constructed site. Because of the processed material used for back-filling and the close spacing of the injection boreholes, control and monitoring often may be accomplished by borehole cameras. Areal Backfilling Areal backfilling is conducted mainly by the pumped-slurry injection process (Fig. 1). In eastern and interior coalfields, material used is often mine refuse or flyash, both being undesirable on the surface and costly to dispose of in an environmentally acceptable manner. Hence, the use of

Jan 12, 1983

By Kenneth Deaton

"A packaged cooling system is being developed for refuge alternatives (RAs) that will meet U.S. Mine Safety and Health Administration (MSHA) qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed refuge alternatives to be maintained by keeping the apparent temperature inside the RA from exceeding 35° C (95° F).Research investigations sponsored by the National Institute for Occupational Safety and Health (NIOSH) have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 35° C (95°F) limit established in 30 CFR 7.504.Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 27° C (81°F) mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines.The Refuge Alternative Environmental Control System (RAECS) will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96-hour refuge period.This article describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 35° C (95° F) limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature — approximately 15.5° C (60° F). The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 29° C (85° F). Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described.Expendable desiccant modules were also used to provide supplemental water vapor removal and their role in mitigating cooling load is addressed."

Dec 1, 2016

By Donald V. Fites

The evolution of open-pit mining has been rapid during the last two decades. The development of larger, more productive and efficient equipment has been one of the key factors in this open-pit advancement. Selection of the proper equipment and its correct usage is paramount to successful operation while maximizing return on investment. The quantity of material being moved prior to mining the saleable product is increasing at a significant rate. For example, at a southwestern copper mine more than two hundred million tons of over- burden have been removed prior to exposing an ore which contains less than 1% copper. A recent survey of twenty-three Western Hemisphere copper mines reveals the average strippingratio was 2.2:l with a range of 0.9-8.5:l. In the face of increased mineral demand, the resulting technological developments and rising overburden to ore ratios, many open-pit mines now use totally different concepts for the removal of ore and overburden. An increasing number of these concepts now being installed include wheel tractor scrapers as a major part of the material handling system for unconsolidated overburden removal. To say scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. As reported in the Minerals Year- book, however, about one-half of the material moved in metal and non-metal mines is never drilled and blasted or broken by other means. We will, therefore, in this paper, concentrate on the role of wheel tractor scrapers in unconsolidated overburden; the area of greatest usage.

Jan 1, 1969

By Ross W. Whipple

Applying geophysical techniques in potential geothermal areas has received: little attention in the United States, though it is widely used and accepted in New Zealand and Italy. In those countries it has been demonstrated that geophysical surveys can be useful in locating new geothermal areas and in directing test drilling programs. Geophysical studies in a thermal region can provide structural information and, if conditions are right directly; locate subsurface hot waters. They can give indications of sub-alluvial rock types and of the thickness of alluvial cover. In certain cases they can be used to estimate the power potential of a hydrothermal system.

Jan 1, 1963

By Warfield Garson

Few, if any, of the non-ionizing radiation health hazards to be found in either surface or underground coal mining are uniquely different because of their being found in the work environment. Hence, they can be considered generally for their bio-effects on the worker when found in the mining work environment. The same may not be said, however, for the lack of non-ionizing radiation and its bio-effects, particularly as it relates to underground coal mining. The term "non-ionizing radiation" refers to various forms of electromagnetic radiation of wavelengths longer than those of ionizing radiation. As the wavelength gets longer the energy of electromagnetic radiation decreases. Therefore, all non-ionizing forms of radiation have less energy than cosmic, gamma, and X-radiation. In order of increasing wavelength, non-ionizing radiation includes ultraviolet, visible light, infrared, microwave, and radiofrequency radiations. The energy frequency and wavelength range of both the ionizing and non-ionizing electromagnetic forces are shown in Table I. To convert the wavelengths of various radiations to Ångström units, one multiplies millimicrons by ten. In a vacuum, all electromagnetic radiation has the same velocity, namely 3 x 1010 centimeters per second. The natural source of radiant energy here on earth is our sun which emits radiation continuously over a wide spectrum. This radiation on average reaching earth ranges from 290 nm in the ultraviolet range to over 2,000 nm in the infrared range with a maximum intensity of about 480 nm in the visual range. You will note this falls into the visible blue wavelength and accounts for our blue sky and blue ocean and deep water effects. We are all familiar with the fact that the passage of solar radiation through the atmosphere to the earth changes the spectrum considerably because the atmosphere absorbs and scatters many of the sun's rays. The ozone in the upper atmosphere absorbs the shorter ultraviolet wavelengths and water vapor absorbs some of the infrared wavelengths. Smoke, dust particles, gas molecules and water droplets scatter the rays, especially those of shorter wavelengths. In addition to the sun, every gas, liquid or solid object at a temperature above absolute 0° radiates energy. Solid objects emit almost continuous spectra. At low temperatures only radiation of the longer wavelengths in the infrared range is emitted, but as the temperature of the object is increased, more and more of the shorter wavelengths are added. This fact is most readily demonstrated by heating a piece of steel. When a piece of steel reaches a temperature of about 1,700° Fahrenheit, it gives off radiation at the red end of the visible spectrum and appears dull red. As the temperature is further increased, the shorter rays are also emitted, until at about 2,100°F, the metal appears white, due to the emission of wavelengths throughout the entire visible range. Gasses, on the other hand, when heated emit radiant energy only at certain wavelengths, which are characteristic of their chemical structure. This latter fact is of importance in underground coal mining as high intensity gas and vapor lamps are becoming more and more utilized for illumination in underground coal mining. The biologic effect of non-ionizing radiation exposure depends upon the type and duration of exposure and on the amount of absorption by the miner. The effects of this radiant energy on the miner fall into four distinct types: (1) the heating effect of infrared radiation, (2) the effect on the eye of visible radiation, (3) the effects of ultraviolet radiation, and (4) the growing potential effects of the misuse of microwave radiation. Each non-ionizing type of radiation will be considered individually. ULTRAVIOLET RADIATION The sun is the major source of ultraviolet radiation, which is of concern in open pit and surface mining at certain seasons and in certain climes necessitating protection for the surface miners under those conditions; nonetheless, there are some man-made sources such as electric arc lights, welding arcs, plasma jets, and special ultraviolet bulbs for illumination underground that demand surveillance in the underground environment to be aware of whether the miners are at risk above the threshold limit values allowable. Since ultraviolet radiation has little penetrating power, the organs that are affected are the skin and the eyes. Ultraviolet radiation is strongly absorbed by nucleic acids and proteins, and the effects in man are largely chemical rather than thermal. Short-term effects on miners include acute changes in the skin. These are of four types: (a) darkening of pigment, (b) erythema (sunburn), (c) increase in pigmentation (tanning) and (d) changes in cell growth. Ultraviolet radiation also causes acute effects on the tissues of the eye. Overexposure can lead to keratitis, inflammation of the cornea, and conjunctivitis. Long-term effects of ultraviolet exposure include an increase in the rate of ageing of the skin with degeneration of skin tissue and a decrease in elasticity. Late effects of ultraviolet on the eye include the development of cataracts. The most serious chronic effect of ultraviolet exposure is skin cancer. Ultraviolet radiation effects are increased by some industrial materials and drugs. After exposure to such compounds as cresols, the skin is exceptionally sensitive to ultraviolet radiation. Photosensitivity reactions occur after exposure to a variety of other chemicals and drugs including dyes, phenothiazines, sulfonamides, and sulfanylureas. On the other hand, we must remember that ultraviolet radiation has an important role in the prevention of rickets. Vitamin D is produced by the action of

Jan 1, 1981