Search Documents

By Tad S. Golosinski

The paper presents the computing stream of the mining engineering curriculum at he Western Australian School of Mines (WASM), a branch of Curtin University of Technology. Learning to use computers begins during the first semester of the initial year of studies and culminates in the Mine Design Project done during the last semester of study. It covers all areas of computing which are judged to be of importance to the graduate.

Jan 1, 1996

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By Stefan Lorenz, Robert Galler

"The technical lifetime of underground structures does not only depend on the long-term behavior of individual support elements and material characteristics, but also on various boundary conditions, which influence the entire long-term system behavior of the structure. Thanks to the construction of second tunnel tubes and the corresponding cross passages sampling of support materials such as shotcrete, concrete of the inner lining and rock bolts including sheet membranes is possible. To evaluate the stresses and the supporting effects of the tunnel shells, flat-jack tests and different simulations were performed. With these simulations the percentage of the load bearing behavior of the shotcrete shell can be determined. From the results, conclusions for new design approaches for tunnel construction should be generated. New concepts, in which the outer lining is part of the permanent support elements can be considered. This approach would be applicable for conventional as well as mechanical tunneling. INTRODUCTION Tunnels are an indispensable part of modern transport infrastructure. As multi-generation structures their long-term preservation as well as their technical service life is of central importance. The current state of research in the field of durability of structural elements must be considered separately. In almost all areas a prediction of materials and structural components towards lifetime exists. System-wide investigations were rarely performed, so that there is no technical lifetime consideration of the outer lining in systems included. In this study the mechanical behavior of the interface connection in a double shell lining (DSL) tunnel was investigated in laboratory tests. Objective The target of this work is, at first, to create a large database with the lifetime of different structural elements and materials, which may be the basis of durability considerations of tunnels. Secondly, the goal of these investigations is to optimize tunnel designs and their dimensioning regarding to the technical lifetime. For that matter, it is necessary to analyze the selected approaches of the loss of strength and stiffness of the outer lining."

Jan 1, 2016

By Kurt Egger, Emily A. Baker

Rehabilitation work at the Cameron Run Tunnels entailed the restoration of seven heavily deformed, approximately 69 m long, steel liner plate supported culverts through a CSX Railroad embankment near Alexandria, Virginia. A custom fabricated expander, equipped with four 200-ton hydraulic jacks on two expansion arms was used to push back the liner plates encroaching into the proposed tunnel profile and install the steel set support. In a second phase the tunnels were then lined with 16 cm of fiber reinforced shotcrete. Geotechnical instruments both in the tunnels and on the railroad embankment were used to monitor the effects of the rehabilitation work on the two CSX Railroad tracks above the tunnels. Freight and passenger trains were required to run uninterrupted and at maximum speeds throughout construction.

Jan 1, 2003

By Sah Rameshwar, T. Umadevi, K. S. SRIDHARA

In the magnetite iron ore pelletization process, oxidation of magnetite followed by sintering of the oxidized magnetite (hematite) is desirable. Optimum preheating time & temperature and roasting time & temperature is required to get the desired properties of the pellets with magnetite, hematite, and hematite–magnetite blend. In order to utilize the magnetite resources in a current induration furnace, which is designed for hematite resources, detailed pelletization studies have been carried out to optimize the firing cycle for magnetite concentrate as well as magnetite with hematite concentrate. Under optimum conditions, such as preheating temperature 1000–1150 °C, preheating time 10 min, roasting temperature 1250 °C and roasting time 7.5 min, the cold compression strength (CCS) of magnetite roasted pellets was 325 kg/p, and this was due to recrystallization of secondary hematite particles, and development of the strong slag bond between primary and secondary hematite particles. The strength of hematite concentrate pellets was 260 kg/p. From laboratory studies, it was found that without disturbing the induration furnace firing cycle, which is designed for hematite ore ~5%, magnetite concentrate can be used along with hematite concentrate in pellet blend and the strength of the pellets was 270 kg/p. As the magnetite concentrate increases in the blend beyond 5%, the preheating zone residence time should be increased or a supply of extra oxygen is required. Laboratory as well as plant investigation has shown that the addition of magnetite to the hematite mix blend improved the strength of the pellets compared to hematite pellet alone.

Oct 26, 2020

By R. Hogg, A. C. Maffei, D. T. Ray

Based on standard population balance models for agglomeration and size reduction processes, a simplified model has been developed to describe simultaneous growth and breakage in the flocculation of agitated suspensions. The results of semi-batch flocculation tests have been used for estimation of the model parameters and empirical relationships have been obtained to describe the effects of process variables and to establish scale-up criteria. Application of the model to the design, operation and control of continuous flocculation processes is discussed.

Jan 1, 1990

By C. J. Slaughter, S. P. Harteis, L. L. Chasko, D. W. Alexander

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways, creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By F. F. Aplan, S. Chander, A. R. Alaboyun

Several aspects of the capture of hydrophobic dust particles by droplets in sprays have been studied. The particle capture depends on several sub-processes involving collision, adhesion and engulfment. The collision events between dust particles and a single droplet were observed with a high speed motion analysis system to determine the influence of a surfactant on the capture process. In the adhesive process it was observed that the dust particles are collected at the surface of the water droplet to produce a rigid film at high dust loadings. In the presence of the surfactant, however, the particles were engulfed inside the droplet keeping a fresh surface on the droplet available for capture of more particles. A theoretical analysis is presented to take into account the role of contact angle on the penetration of particles into droplets. A significant increase in collection efficiency was observed with decrease in droplet size.

Jan 1, 1991

By E. Robert Kiehl

In the early days of the United States, gypsum was most commonly used for the manufacture of plasters with energy being used for quarrying, grinding, and calcining of gypsum rock. With the dramatic switch to gypsum-drywall construction after World War II, the energy usage per ton of rock processed increased more than threefold, and with the rapid growth of the construction industry, the total energy consumption in gypsum-board production alone increased eightfold during the period from 1940 to 1973. The gypsum industry was one of the first to recognize the need for energy conservation and has voluntarily reported its progress to the Federal Energy Administration for the past several years. Efficiencies in the use of energy have resulted in decreasing the unit consumption an estimated 10 percent during the past six years. Improved combustion efficiencies, optimum operating conditions, more liberal use of insulation, and heat recovery will all contribute to the gypsum industry's goal of using less energy. Gypsum products today are vital to over 85 percent of new housing construction in the United States.

Jan 1, 1978

By D. S. Choi

This paper presents the results of geomechanics work applied to the longwall operation. The mining method was successfully adapted to US mining conditions resulting in an improvement in safety and productivity. The paper deals with various geomechanics problems associated with geologic and mining conditions.

Jan 1, 1987

By T. F. Torries

Market data commonly perceived as being useful to industry for decision making include prices, production and trade quantities, production and transportation costs, stocks, customer's needs, and competitor's qualifications. Costs and factors affecting costs are particularly important in determining competitive positions and possible future prices. These costs include relative cost of production as well as cost experienced by the buyer in making the final product. Care must be taken to calculate costs in a consistent manner to achieve meaningful analyses.

Jan 1, 1987

By M. E. Gershon

Extensive efforts are under way toward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics, and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1987

By Robert H. Carpenter

Abstract, Syngenetic uranium in pre metamorphic Idaho Springs volcanics and sediments probably, was mobilized during metamorphism (1.7 b.y.) and partly retained along unconformities. Precambrian Silver Plume intrusives (1.4 b.y.) and Pikes Peak granite (1.0 b.y.) may have mobilized uranium from the craton and. Idaho Springs metamorphics to concentrate it in cauldron sites in migmatites, pegmatites, alaskite, disseminations and greissen. Tertiary intrusives also may have upgraded uranium by anatexis, leaching and differentiation. Tertiary vein and shear zone uranium mineralization may have-been-derived from underlying magma sources, leached from Idaho Springs metamorphics and from syngenetic leaching of overlying sediments and introduced by deep hydrothermal convection systems.

Jan 1, 1979

By K. Pietruszka

The article presents the concept of the application of the Finite Element Method (FEM) and ABAQUS software in the global monitoring of changes in the rock mass and on the surface of the area, as a result of backfilling the workings. Waste materials applied for stabilizing old mining workings can have a strong influence on the rock mass and surface. According to the regulations, this process should be carefully monitored, especially in terms of the safety of surface structures and rock mass stability. The article presents the concept of an analytic and graphic presentation of the results of the measurements of old workings, applying the Finite Element Method and ABAQUS software in model studies. The main purpose of such interpretation of the geodetic observations results is the application of methods providing wide possibilities to present the geometry of workings, their changes and the influence of the rock mass and surface.

Jan 1, 2008

By Miles L. Silberman

Three major suites of igneous rocks were erupted in the Great Basin in middle and late Cenozoic time. The first, most likely, resulted from sub- duction of a Pacific plate (Farallon plate) beneath the North American plate, resulting in eruption of andesitic rocks in the northern Great Basin between 42 and 43 m.y. ago. Between 34 and 17 m.y. ago, igneous activity migrated to the southwest, largely as eruption of volumincus rhyolite-quartz latite ash-flow sheets, ending about 17 a.y. ago with the onset of crustal extension and north-south-trending Basin and Range (rift) faulting. The second volcanic suite erupted between 17 and 8 m.y. ago in the northern Great Basin; is mostly basaltic or bimodal basalt-rhyolite. The third volcanic suite consists of andesitic and rhyolitic lavas and some basalt erupted between about 22 to 6 m.y. ago in the western Great Basin along the northwest-trending Walker Lane fault zone. Hydrothermal ore deposits are associated with all suites of igneous rocks, but the largest production has come from mines associated with andesitic rocks of the third (western Great Basin) suite. The oldest (34 to 42 m.y.) andesitic rocks (first suite) of the northern Great Basin have produced some large deposits; slightly younger silicic rocks of this suite are mostly barren. Many small ore deposits are associated with the 17- to 8-m.y.-old basalts (second suite) of northern Nevada.

Jan 1, 1976

Paper and paperboard manufacturers need to quantify the carbon footprint and environmental impact of their products to satisfy market, social and government demands. Coated paper products contain minerals, such as kaolin and calcium carbonate, at significant levels; some coated paper grades have mineral contents as high as 45% by weight. Some uncoated paper has no mineral content, but most uncoated paper contains some mineral to improve appearance, process efficiency and cost. Super-calendared paper grades can contain levels of mineral up to 35% by weight. This paper describes how to calculate the carbon footprint of kaolin and calcium carbonate minerals used for white pigments. The carbon footprint of these minerals strongly correlates to the primary energy sources, final product form and energy used to calcine kaolin and lime. Kaolin and calcium carbonate pigments have a favorable impact on the carbon footprint of paper and paperboard products by directly substituting for fiber and by reducing the energy needed for paper making. Key words: Kaolin, Calcium carbonate, Paper production, Carbon footprint, Lifecycle analysis

Jan 1, 2010

By G. D. Mainwaring, Weng L. W, Lam Y. K.

The first power transmission cable tunnel in Singapore was the 2.6km long undersea tunnel between Pulau Seraya and mainland Singapore, constructed in the1980s. Ten years later, similar concepts were used for the Tuas Cable Tunnel. The tunnel, which includes a 2.2km long immersed tube section, was designed to accommodate 10power circuits of 400kV and 230kV capacity. It is fully equipped with sophisticated control and communication equipment, fire suppressant and life safety systems plus a maintenance vehicle which runs on tracks through the length of the tunnel. The paper discusses the planning, design, and construction of the Tuas tunnel, and the development of these concepts for future tunnels.

Jan 1, 2001

By S. A. Beeson, C. Poole

This paper describes the development of a novel selective flocculation technique for recovering phosphate values from ores containing silicate or carbonate gangue minerals. Data from initial flocculation response and reagent adsorption studies on component mineral suspensions and synthetic mixtures were used to assess the influence of various process parameters (e.g., reagent dosages, particle size, solids concentration, and conditioning regimes) on single-stage selective flocculation tests involving natural silicate and carbonate ores. In these tests a high degree of selectivity was achieved using low dosages of a low-molecular-weight cationic dispersant and a mid-range molecular weight cationic flocculant. Testwork was then extended to the evaluation of several floc recovery systems (sedimentation, hydrocyclones, and floc flotation) in a multi-stage process involving redispersion and reflocculation. Results from these tests clearly demonstrated the feasibility of producing marketable phosphate concentrates from both ore types.

Jan 1, 1999

By J. L. Weaver

The spiraling rate in phosphate rock demand during the period 1957 to 1967 led producers to expect a continuation of a high growth rate. Consequently they expanded production capacity to meet the expected demand. Both the domestic and the world demand has shown little growth over the past three years. Florida producers operating at less than 75% of installed mining capacity, produce all that their markets will absorb. We expect that the nest few years will bring only a slight improvement in this condition. An increased demand in the domestic agricultural market will be partially offset by a continuing erosion in the export market.

Jan 1, 1972

By C. H. Stephenson, Z. White

This paper presents the design approach case study for incorporating a Technogrid® conveyance End-of-wind arresting system within the new South32 Hermosa headframe. Focus is placed on energy absorption requirements, structural integration, and mounting details tailored to the geometry and operational constraints of the headframe. Key considerations include arresting forces, load path continuity, and connection design to ensure reliability and maintainability. The paper also discusses coordination with other headframe systems and the iterative design process used to meet safety standards and client objectives.

Feb 22, 2026