Search Documents

By J. Kretschmann, H. Mischo, O. Drusche, S. Krause

Mining is and will be inevitable in spite of the increasing implementation of circular strategies. The energy transition and population growth will boost the demand for critical raw materials. It is the opportunity for miners to reinvent their business models. Generating attractive new business cases with sustainability-oriented innovations meets investor and stakeholder expectations from the beginning. This contribution guides managers on their pathway towards sustainable success. Contextual sustainable business model patterns will be presented that can be adjusted individually, regardless of actor’s size. It will also point out, how sustainable value creation can be measured on business model level.

Feb 1, 2023

By Blagoj Golomeov, Boris Krstev

Nowadays, in the papers of authors in the area of flotation concentration, we can find several equations that describe the kinetics of flotation process as follows: Agar's equation, Klimpel's equation, Beloglazov's equation and Group of authors' equation (equation with two kinetic constants). This paper makes an attempt to determine the most appropriate equation for mathematical interpretation of kinetics of the SASA mine rougher Pb - Zn flotation.

Jan 1, 2002

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By P. Berendsen

The tectonic and sedimentary environment of the Central North American Rift System (CNARS) provides all excellent setting for major mineral deposits. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending transcurrent fault systems may exercise control over ore forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu. Ni, Co, Ti, Au. Ag and PG-minerals are known to occur in this setting. Arkosic sandstone, siltstone, shale, and minor carbonate units occur on top of the rift basalts and in flunking basins where they may reach thicknesses of 10 km (6 miles). The potential, for stratiform or unconformity-related metalliferous deposits must be considered. The rift as a whole remains, however, largely unexplored.

Jan 1, 1990

By W. J. Dolinar, S. P. Sandoval

The US Bureau of Mines (USBM) implemented the Fe2+/ Fe3+-SO2 anode reaction in a Cu-electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/ m2 (24 A/ft2) and 40°C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb), compared to conventional electrowinning. Acid milling 5was completely eliminated, and the SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1996

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

By R. W. Lai

Cyclic voltammetry (CV), flotation response, evolved-gas analysis (EGA), and X-ray photoelectron spectroscopy (XPS) were employed to evaluate the major differences in the surface property and surface reactivity of coal pyrite and mineral pyrite.

Jan 1, 1989

By Eric M. Hill, Daniel E. Walsh, Hsing K. Lin, John T. Hollow

The Fort Knox Mine is located in Alaska’s interior where the average ambient air temperatures range from -24°C in January to 16°C in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Plant slurry temperature cycles seasonally and allows for a unique opportunity to measure the impact temperature has on gold leach kinetics, carbon adsorption efficiency and cyanide destruction reactions. Mathematical models have been developed to accurately predict actual mill performance. This paper describes the development of the models and presents data that allow for a better understanding of the impact of circuit operating temperature on process efficiencies.

Jan 1, 2005

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By A. Wright, R. L. Kastelic, W. C. Feyerabend

Gold Fields Mining Corp. is evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek project, Humboldt County, Nevada. Contamination of reverse-circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse-circulation holes appear to define mineralized zones almost as well as diamond-drill holes. To improve reverse-circulation sample integrity, several techniques were tried (including a stiff-mud injection system) but with limited success. Diamond-core drilling continues to be used in conjunction with reverse-circulation drilling to further delineate the mineralization.

Jan 1, 1993

By Paul B. Queneau, Barry J. Hansen, D. Erik Spiller

Most lead and zinc secondaries are recycled pyrometallurgically. However, many problems encountered in secondary smelters have been solved by addition of physical concentration and/or hydrometallurgical processing steps, with resulting important environmental benefits. U.S. secondary lead and zinc operations are described, covering conventional smelters, EAF-dust treaters, and zinc sulfate/fertilizer producers, including plant capacities, technologies, and outputs. During the past two decades, remarkable advances have been achieved by recycling spent lead-acid battery components. Interaction between primary and secondary zinc producers, the fertilizer industry, and the zinc chemical industry has substantially decreased waste generation.

Jan 1, 1993

By Christian Neumann, Josef Arnold, Albin Reinhart

The Channel Tunnel Rail Link (CTRL) is the most significant railway infrastructure development project in the United Kingdom since the construction of the Channel Tunnel between France and England. The key element of this project is the 2-mile-long(3.2-km) North Downs Tunnel, which will be the largest and deepest twin-track railway tunnel ever constructed in the United Kingdom. This paper describes the contractual agreement, the design and construction (excavation and lining) of a twin-track rail tunnel with a 166-m 2 face excavated through chalk using the New Austrian Tunnelling Method (NATM). The importance of collaborating with a tunnel contractor/designer who not only is expert in the New Austrian Tunnelling Method, but who was also responsible for the design and installation of the primary lining, will be highlighted in this paper. This paper will also deal with the benefits of partnering in tunnel design and construction, as well as the resultant added values of mechanizing conventional tunnelling methods (Value Engineering).

Jan 1, 2001

By J. M. Cases

Diffuse - reflectance Fourier - transform infrared spectroscopy, Hallimond tube flotation and microelectrophoresis have been utilized to investigate the reactions involved in the adsorption-abstraction of K-amylxanthate on finely ground galena and pyrite. In order to work under well-controlled conditions both minerals were wet ground in a specially built laboratory stainless steel or iron mill. Four surface products were found to be formed on galena: monocoordinate lead xanthate, non-stoichiometric lead xanthate, dixanthogen, and amyl carbonate disulphide. Only dixanthogen was observed on pyrite after using stainless steel rods, while ferric iron xanthate was found when iron rods were utilized.

Jan 1, 1989

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

By C. J. Hall

The simplest natural ventilation cycle is similar to a Joule or Brayton cycle. This comprises two reversible adiabatic processes in the shafts and constant pressure processes underground and on surface. The thermal efficiency of such a cycle is given by the temperature increase in the downcast shaft divided by the absolute temperature of the air at the bottom of the downcast shaft, and is independent of the temperature increase underground. This efficiency is comparable to the Carnot efficiency, which is the greatest possible value between constant temperature reservoirs, source and sink. Two variations of the Joule cycle are investigated, using numerous work examples. In the first, dry air is used as the working substance, a fan is provided at the top of the upcast shaft, and various mass rates of flow are used with frictionless shafts and a constant resistance value in the horizontal mine workings. The lost work less the fan work gives the natural ventilation work, and this divided by the enthalpy increase in the workings gives the thermal efficiency. The thermal efficiency increases dramatically with mass rate of flow, although the enthalpy increase remains constant. This appears to violate the second law of thermodynamics, since the frictionless case has a Carnot efficiency. When the lost work is added to the enthalpy increase, however, the efficiency decreases slightly from the Carnot value, to conform with the second law. This increase in efficiency with mass rate of flow is often referred to as the reheat effect, although the air is not heated. The second investigation is similar to the first, except that the air entering the downcast shaft contains a small amount of water vapor, and there is evaporation in the mine workings only, until the air entering the upcast shaft is saturated. There is, of course, condensation in the upcast shaft. In this case, it is not possible to calculate the Carnot efficiency, but the thermal efficiency is 20 to 40% of the similar dry air values. This decrease is much more than can be accounted for by the larger value of specific heat for water vapor. In addition, the natural ventilation work is almost constant with increased mass rate of flow, and the thermal efficiency based on heat addition tends to decrease. The thermal efficiency based on heat and lost work decreases in conformity with the second law. The reasons for the differences in behavior between dry and moist air are not readily apparent.

Jan 1, 1991

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By E. W. Geist

This paper is presented from the viewpoint of the mill operator and maintenance supervisor. Its purpose is to highlight the things that have been accomplished by the mill designers to lighten the load for the maintenance superintendent and to reduce the overall costs for the plant operator. The complexity of plant design, the civil and structural engineering problems encountered when the satisfactory maintenance layout is accomplished are appreciated, and the writer is fully aware of the complexities of these problems. However, it is not the purpose of this particular paper to dwell upon these problems, nor to emphasize or de-emphasize the problems of the civil, mechanical and electrical engineers. It is simply that the paper will attempt to review what these people have accomplished in spite of the many technical problems. This paper then is prepared with the operator and maintenance people?s viewpoint. What is their definition of design for maintenance? It is the writer's interpretation that the various design concepts which mean improved maintenance are such items as (I) maintenance areas, (2) laydown space for maintenance materials in specific maintenance jobs, (3) the inclusion of bridge cranes in the plant and specific design of the craneways to accomplish flexibilities for the cranes, and (4) the location of the piece of equipment to allow maintenance people to work around the equipment - - - this specifically includes the orientation of the particular piece of equipment.

Jan 1, 1967

By John W. Harshbarger

The Upper Santa Cruz Groundwater Basin lies in the drainage area of the Santa Cruz River in Arizona, and extends upstream from the community of Rillito to the international boundary, see Figure 1. The principal water use area lies between and includes the cities of Tucson and Nogales. A subsurface geologic barrier near Rillito provides a reasonable dividing line between the groundwaters of the Upper and Lower Santa Cruz Basins. The Upper Basin contains the Tucson and Sahuarita-Continental critical ground- water areas. The Tucson Water Use Area encompasses the Tucson metropolitan area and extends from the northern boundary of the Basin south to the boundary between the Tucson and Sahuarita- Continental critical groundwater areas near San Xavier. The San Xavier Use Area is the San Xavier Indian Reservation. The north and south boundaries of the Continental Use Area coincide with the limits of the Sahuarita-Continental critical groundwater area. The first study of groundwater in this valley was initiated by Dr. G. E. P. Smith in 1905 and the results were published in 1910, followed by a series of bulletins of the Arizona Agricultural Experiment Station, University of Arizona, covering the general field of groundwater development and utilization. Beginning in 1939, the Ground Water Branch of the United States Geologic Survey, in cooperation with the Arizona State Land Department and the Arizona Water Commission (AWC), have published a series of bulletins concerning groundwater occurrence and utilization in various areas of the state. In 1975 and 1977, the AWC published the "Arizona State Water Plan" (1), comprising a detailed inventory of water availability and use in the State of Arizona, and a study of alternative futures.

Jan 1, 1979

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994