Search Documents

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association four distinct facies (oxide, carbonate, silicate, and sulfide) were identified in an Algoma type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and CO2. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1981

By M. Deal

Particle size analysis is a fundamental measurement utilized in the mining industry, especially in comminution, hydrometallurgy, and mineral processing. While sieves and cyclosizers are the standard methods used to determine particle size distributions, in recent years alternative instruments have been developed that claim to provide more rapid and equally reliable results. Newmont Metallurgical Services has implemented the use of two such instruments, along with traditional methods (sieves and a cyclosizer), on a daily basis. The Malvern Mastersizer 2000 laser analyzer is a wet sample system that can analyze particles in the size range 0.02µm to 2000µm, and the Horiba CAMSIZER® is a dry system that can analyze particles in the size range of 30µm to 30mm using digital image processing. A comparative analysis has been performed to determine the applicability of each particle sizing method in laboratory testing.

Jan 1, 2011

By A. Shah, L. W. Saperstein, M. C. Radomsky, D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the US Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1990

By J. Peshel

This paper presents a regulatory perspective of the design and construction of the Exploratory Shaft Facility which may become part of the future high-level waste repository. Site characterization concerns and long-term waste isolation concerns require the consideration of various shaft design and construction aspects quite different from that of conventional shaft sinking.

Jan 1, 1989

By G. Folmo

Allis Mineral Systems' GRATE-CAR agglomeration/induration/reduction process is currently being operated to process ilmenite at Tinfos Titan & Iron KS in Tyssedal, Norway. In this process, balled ilmenite concentrate is fed to a traveling grate where pellets are dried and preheated, using fully oxidized kiln exhaust gas. Hot preheated, semi-indurated pellets are fed directly to a ported kiln where reduction of the ilmenite's iron oxide fraction occurs in the presence of lump coal. The reduced pellet sand coal char are discharged from the kiln to an indirect rotary drum cooler. Cooled pellets and char are screened and magnetically separated prior to their further processing in a downstream smelting operation. The pellets are melted and the titanium dioxide and iron are separated. Operation commenced in late 1986.

Jan 1, 1992

By F. F. Aplan

Mineral process engineering is a small but important part of the nation's raw material industry. Minerals are usually processed in large plants of high capacity, at low cost, using few engineers and operators, and at an ever-increasing level of plant sophistication. The magnitude of the mining industry is huge, with about 4 Gt (4.5 billion st) of ore, coal and industrial minerals mined annually in the United States. Industries such as construction, manufacturing and power generation rely heavily on a strong US resource base to maintain a competitive edge. Though rooted in classical chemistry, geology, physics and mathematics, a mineral process engineer must be trained in the science and engineering required to process raw materials. A modern mineral processing program still stresses the traditional aspects of the profession. But it also emphasizes particle technology, applied surface chemistry, chemical processing of ores, solid-fluid separations, process and equipment modeling and optimization, materials handling, personnel management, maintenance and environmental and health aspects. In such areas as particle technology and some aspects of applied surface chemistry, mineral processing academic programs have taken a leadership position in supplying specialists to a variety of other industries. The objectives of a mineral processing program are: • to furnish personnel to support the basic raw materials industries (undergraduate programs); • to provide a research and development base for industry (graduate programs); and • to provide expertise in particle technology, applied surface chemistry and environmental programs for other industries (undergraduate and graduate programs). In the United States, mineral process engineering programs have historically been associated with mining and metallurgy departments. The recent movement of metallurgy programs away from primary processing towards materials science has created the need for a new accommodation.

Jan 1, 1992

By H. M. Brennecke

A new hydrometallurgical process has been developed to recover copper from sulfide ores. Copper is leached in a staged reactor system utilizing nitric and sulfuric acids at 105°C. Iron is removed from the pregnant liquor as a jarosite and cathode copper is electrowon directly from the purified pregnant liquor. The spent electrolyte is recycled. Nitrogen oxides evolved from the leach are reconverted to nitric acid and are also recycled. Sulfur is rejected as S°, jarosite and gypsum. The process is highly versatile and can recover precious metals, molybdenum and zinc, when these elements are present. Continuous, integrated, semi-pilot plant operations using chalcopyrite ores demonstrated 99% copper leaching and production of cathode grade copper. Economic evaluation shows that the process is competitive with pyrometallurgical and other hydrometallurgical processes.

Jan 1, 1978

By Steven E. Mischler, Jay F. Colinet

The Mine Safety and Health Administration (MSHA) promulgated a rule in 2014 that required numerous changes in compliance dust sampling requirements for coal mine operators. Two key parts of this rule were the lowering of the respirable coal mine dust standard from 2.0 mg/m3 to 1.5 mg/m3 and requiring operators of underground coal mines to use a continuous personal dust monitor (CPDM) for compliance sampling. The CPDM currently approved for compliance sampling is equipped with a display that provides miners with in-shift information on their respirable dust exposure. The goal was to provide an indication of a potential overexposure and empower the miner and mine operator to implement changes in controls and/or operating practices to prevent an overexposure from occurring.

By M. F. Corcoran

Rapid advances have been made in the past few years in the application of automatic controls and instrumentation to iron ore pelletizing plants. Present practice in applying instrumentation and control to the Grate-Kiln system of iron ore pelletizing is described. Major control points and loops are tabulated. Future trends in the application of digital control including computer data logging systems are described.

Jan 1, 1965

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By D. R. Spears

The U.S. Bureau of Mines has developed a Fast Air-injected hydrocyclone-Shallow Tank (FAST) flotation system. Conventional flotation cell kinetics are a compromise between two conflicting requirements, the need for an agitated zone for rapid bubble-particle collision, and a quiescent zone for bubble-pulp separation. The Bureau of Mines has designed a flotation system in which bubble-particle collision and bubble separation are carried out in two discreet unit operations. A bubble slurry was mixed with an ore slurry at a high rate in a modified air-injected hydrocyclone for rapid bubble-particle collision. The mixture was then fed into a unit specially designed for rapid separation of the bubbles from the pulp. A conventional flotation cell required 2.8 min to obtain 90 pet recovery at a 7-pct Cu rougher concentrate grade, whereas the FAST flotation system can obtain 85 pet recovery with a 13-pct Cu rougher concentrate grade in 0.28 min, and 92 pet recovery with a 7-pet Cu grade in 0.56 min. The Bureau's FAST flotation system is adaptable to a wider variety of flow sheets and could potentially allow for replacement of conventional flotation cells with smaller and faster units.

Jan 1, 1991

By Edward H. Eisenbrey

This paper is primarily concerned with the exploration for massive sulphide orebodies. In a discussion of this type, it seems appropriate to establish a few definitions so that all parties may consider the same beast and its habitat. First, the term "massive sulphides", as used here, not only denotes a body of mineralized rock containing in excess of 50% sulphides by volume, but a mass of sulphides that respond as a conductor to the electromagnetic (EM) systems currently in use in exploration. "Disseminated sulphides" refer to all of those sulphide occurrences that respond to the Induced Polarization (IP) geophysical methods most commonly in use in porphyry copper exploration. This latter definition may also include the disseminated sulphide halos so frequently found associated with massive mineralization as well as banded and stringer sulphide mineralization. It is plain to see that these two end members of our definitions can easily blend into each other. The term "volcanogenic" refers here to any and all geologic processes that have their origin in volcanic activity. Thus we are concerned here with the exploration for massive sulphide ore deposits derived from and affected by contemporaneous and post mineral volcanic activity. Furthermore, most massive sulphide deposits are apparently formed in a submarine environment, deposited with extrusive rocks and sediments and/or chemical hot spring accumulations, then enclosed and protected by the addition of more volcanic and sedimentary material then, probably folded and deformed into one of their myriad of shapes.

Jan 1, 1973

By F. Repmann

Waste-dumps originating from the mining industry constitute a serious environmental problem if they are not properly rehabilitated. Industrial and domestic sewage sludge from waste water purification plants on the other hand constitute a problem of environmentally acceptable disposal as these residues contain a large number of potential contaminants. The current project aims at developing an integrated methodology to rehabilitate the mining waste-dumps by the use of sewage sludge so that the two mentioned problems will be solved at once.

Jan 1, 2002

By Richard R. Klimpel

This paper reviews some of the factors involved in selecting amine flotation reagents used to remove silica from ores. A comparison is made between the chemical reagent design approaches used to identify flotation reagents that are used to recover silica- and oxygen-containing minerals and the chemical reagents used to recover sulfide minerals. This introduction gives practitioners who are involved with oxide- and carbonate-type minerals and who may not be familiar with sulfide mineral flotation some ideas of the chemical reagent design challenges that exist with froth flotation on a broader scale and why oxide type mineral flotation reagents are what they are. This is followed by several sections that discuss various classes of available amines. The closing sections emphasize that the optimal choice of an amine collector depends not only on that amine's specific chemical characteristics and costs but also on the operating conditions, especially the flotation feed particle size distribution.

Jan 1, 1999

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying an atomic force microscope (AFM) and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy to study in situ the adsorption of three different collectors — oleic acid, octanohydroxamic acid (HA) and salicylhydroxamic acid (SHA) — on bastnaesite in aqueous solutions. The results show that all three collectors adsorb on bastnaesite. The hydroxamic acid collectors — HA and SHA — adsorb on bastnaesite mainly in the form of insoluble metal hydroxamate. Their specific adsorption mechanism indicates that high selectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By R. A. Hodge

Over the past decade, there has been a significant increase in effort put to tracking progress toward sustainability. Many aspects of society are participating in this “movement” including mining. The drivers are diverse and include evolving ideas in business and public administration as well as concerns for human well-being, community robustness, environmental integrity, and overall social and ethical responsibility. The scale in question varies greatly from local to global. For the most part, there has been a pre-occupation with developing discrete measurable signals. This paper argues that the overwhelming focus on the quantitative is ill-advised and that a more effective approach is to bring together the best of both quantitative and qualitative. The mining industry in particular is well-placed to affect this shift and reap the associated benefits.

Jan 1, 2004

By R. J. Boyd

SUMMARY The productivity of drill and blast methods of mining in hard rock is limited by the cyclic nature of the operation, and a plateau of performance has been reached, even with the most advanced equipment developments. Higher mine operating costs and lower metal prices have more than ever generated the need for breaking through these productivity barriers. After initial field testing The Robbins Company has designed and manufactured, on a joint venture basis with Mount Isa Mines, Ltd., Australia, a prototype "Mobile Miner" for continuous cutting of hard rock. This paper describes the cutting concept, the initial application of a completed 1,156 m (3792 ft.) long 14% decline, actual performance and delay analysis, developmental modifications, anticipated performances of a fully developed machine, and possible future applications. Sincere appreciation is expressed to the management of Mount Isa Mines, Ltd., for allowing access to the data used in this paper. The views expressed here are those of the author and not necessarily those of Mount Isa Mines, Ltd. INTRODUCTION A paper titled, "Design and Development of a Mobile Mining Machine", was presented by J.P. Kindsvater at the RETC, New York, in 1985. This paper described the evaluation of a test fixture in an andesite quarry near Seattle, followed by design, construction and

Jan 1, 1987

By Ralph J. Anctil, James E. Palmer

According to relatively recent estimates by the US Geological Survey and the US Bureau of Mines, there are more than 0.9 Tt (one trillion tons) of remaining identified coal resources in the seven major western US coal-producing states and about 200 Gt (220 billion tons) in the demonstrated reserve base. Considering coal's current national production level of 0.7 Gt/a (0.8 billion tpy), these US reserve and resource figures are reassuring. Given here is a preliminary analysis of geologic constraints and an estimate of their effects on mining and recoverability of western coal. Mining Constraints USGS and USBM coal figures incorporate only thickness and depth, and are "blind" to many other major geologic constraints on mining and recoverability. The most important of these geologic constraints include: • coal seams too thin or too thick for conventional mining methods; • coal seams that cannot be mined due to insufficient separation from underlying or overlying previously-mined beds; • unstable or otherwise unfavorable roof strata; • soft or heaving floor strata; • coal seams that are too lenticular or discontinuous for conventional mining methods; • coal seams in intensely faulted areas; • coal seams having high angles of dip precluding the use of conventional coal mining methods; • coal seams that cannot be mined due to proximity of water-bearing strata; and • coal quality problems such as excessive ash, sulfur, chlorine, or sodium. Coal Thickness Present USGS-USBM classification for reserve base includes bituminous coal beds more than 0.7 m (28 in.) thick and subbituminous beds more than 5 m (60 in.) thick to depths of 305 m (1,000 ft). Both of these thicknesses are less than the thicknesses now considered mineable in the western US. The lower limit for bituminous steam coal in deep mines is about 1.5 m (5 ft). For subbituminous coal, a thickness of at least 2.4 m (8 ft) is generally required. Accordingly, the Bureau of Mines reserve base includes many thinner coal seams that will not be mined in the foreseeable future. Within the Powder River Basin of Wyoming and Montana many seams-Wall, Upper Pawnee, Lower Pawnee, Cache, Manning-range in thickness from 7.6 m (25 ft) to more than 30 m (100 ft) and occur at depths to 305 m (1,000 ft). These have been included in the Bureau of Mines reserve base. However, the mining technology required to mine these thick seams does not now exist. It will require many years for development. The ultimate recoverability from these thick seams is unknown, but could be as low as 25%.

Jan 8, 1982

By G. Wahl, H. Danilkewich, T. Mann

Developers of advanced mining projects face the challenge of how to craft a “Request for Proposal for a Feasibility Study” that will result in bids that are comparable and will lead to a successful execution of the study. Mining engineering consulting firms are challenged by “Request for Proposals” that may consist of a limited description of the Scope of Services and other items, which could present difficulties in the subsequent financing and/or development of the project. Changes in international disclosure requirements have also changed the landscape on how resources and reserves are reported by introducing new disclosure requirements and concepts such as qualified persons. This paper lays out a strategy for preparing a Feasibility Study “Request for Proposal” based on the experiences of a mining engineering consulting firm working on a diversity of projects around the world, and in light of the recent changes in international reporting standards for reserves.

Jan 1, 2002