Search Documents

By James Parkes

"The proposed Baltimore Red Line light rail system includes a 3.4 mile downtown tunnel (DTT) with five underground stations. The design of the underground stations involved overcoming several challenges, including limited right-of-way, high groundwater and uplift pressures, and metamorphic rock within the station depths. An innovative design was developed to maximize the internal station space while minimizing cost. The station designs use slurry walls for temporary and permanent support and groundwater control. Depths within rock are supported with cast-in-place concrete walls, the thickness of which are minimized through the use of permanent rock anchors for support of the rock mass and slurry wall toes. Permanent tiedown anchors are used for uplift resistance, which minimizes the station depths, volume of rock excavation, and the volume of deadweight concrete. Design considerations regarding individual elements and overall integration of the slurry walls, CIP walls, and multiple anchor types are presented.INTRODUCTION The Baltimore Red Line (BRL) project is a proposed light rail transit line for the Maryland Transit Administration (MTA) that runs east to west through Baltimore City and County. The project includes the Downtown Tunnel (DTT) consisting of 3.0 miles of twin running tunnels, two portals, five underground stations, and a pedestrian tunnel, as shown in Figure 1. The tunnels have an outside diameter of 21.8 feet and are designed to be mined using pressurized face tunnel boring machines (TBMs). The stations, portals, and the pedestrian tunnel are designed as cut-and-cover structures using slurry walls (concrete diaphragm walls) for both temporary support of excavation (SOE) and permanent structural walls. The dimensions of the five underground stations are summarized in Table 1. Design challenges included limited right-of-way (ROW), challenging soils conditions, strong metamorphic rock within the station depths, and high groundwater conditions. The final station designs included innovative use of slurry walls, tieback anchors, rock anchors, and tiedown anchors."

Jan 1, 2016

By T. M. Yegulalp

One of the important factors affecting the determination of the minimum number of increments in a gross sample of coal is the variance component due to segregation. The segregation variance may be estimated by following the ASTM standard procedures. Since the estimate itself is a random variable, it is important to test if the value obtained is due to chance causes. This paper introduces a statistical test, based on the procedures published by ASTM, to test if the segregation variance is significantly greater than zero.

Jan 1, 1986

By Roger Storry, Donald Bruce, Arnaud Hochart

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands and under the main shipping channel in Biscayne Bay (Figure 1).The POMT was a unique project which embodied many technical firsts and involved the first large diameter tunnels constructed through Florida’s challenging sedimentary carbonate strata. At the outset, a comprehensive ground investigation was performed, using both conventional and less conventional investigation techniques, to characterise the highly heterogeneous ground conditions.The findings of the investigation had a major impact on the tunnelling methods, triggering a series of mitigation works to ensure that the tunnels could be excavated safely and effectively. The mitigations included modifications to the already designed Tunnel Boring Machine (TBM), to facilitate an innovative excavation process, and a unique grouting campaign (Storry et. al. 2013a). The project was completed and opened to traffic in August, 2014 and has significantly alleviated traffic congestion in Downtown Miami.GEOLOGICAL CONTEXTThe geological conditions at the project site consist of carbonate sediments which can be divided into distinct geologic units; the Miami Limestone Formation (Layers S3, S4), the Fort Thompson Formation (Layer S5), the Anastasia Formation (Layer S6), the Key Largo Formation (Layer S7) and the Tamiami Formation (Layer S8). Multiple changes in sea level over a relatively short geologic time scale have resulted in a heterogeneous profile consisting of interbedded sedimentary rocks and sediments, which vary widely, both vertically and laterally (Figure 2)."

Jan 1, 2016

By J. A. Herbst

Introduction The ability to evaluate the improvement resulting from the implementation of an automatic control system is essential to the Justification of its cost. This evaluation may occur after anew control system has been commissioned. In other cases an existing plant which is operated manually may be automated only In part in order to determine In ether the met of it should be. Finally. in some instances dynamic isolation my be used prior to installation of the control system to determine the strategy to be used or to evaluate the improvements In process performance expected from automatic control. This paper describes the development of a methodology for making these evaluations. In order to obtain an accurate assessment of Improvements In a short time, statistical methods can be employed. Mineral processing plant, are subjected to many types of both random and deterministic disturbances of various duration. The statistical method, available for process control at analysis are designed to counter the obscuring effects that random disturbances have on such as evaluation. The basis for evaluation and comparison is some freely chosen measures of process performance termed the performance index or objective function. The experimental data used to calculate the performance index should, if possible, be collected by alternately running a circuit Or plant with the two or more type, or control being tested ("serial testing”) or more preferably, by running two circuits with the two type, of control side by side ("parallel testing") . The performance index is a random variable so that when comparing two types of control, statistical hypothesis testing must be used. By testing s hypothesis statistically one accept, or reject, a (null) hypothesis [ ] concerning the mean or variance of one or more performance indices. For example, a hypothesis Ho might be that the mean of a performance index with stabilizing control is larger than with manual control. Defining a Performance Index The performance index, denoted by [ ] , is a measure by which alternative strategies or situations my be cam peered on either s technical or an economic basis (see Table 1). Technical measures are concerned with the effects of control on process variables or outputs or on the deviations of controlled variable, from their setpoints. For commotion circuit, important technical measures of performance are throughput, product fineness and the consumption of liners, media and electrical energy. For flotation circuits important technical .satires are recovery, grade and reagent consumption. Economic measure such a, cost and profit n usually determined from a combination of technical measures and are usually the final factor upon which a decision may be made, although a control system my achieve higher values of technical measure , the control effort expended my be of such magnitude that the economic measures, such as cost, are poor. Running Comparisons Comparison, between automatic and manual control are normally done with data obtained before and after control system Installation, unless ore characteristics remain the same during the period of data collection the results will be biased. By running the test circuit with the control system alternately turned on and curled off until all possible ore type, have been run through the circuit, unbiased result, can be obtained. This mode of testing is termed “serial testing.” An alternative and potentially more powerful and quicker made of testing is "parallel testing" in which two circuits, one with the type of control being tested and one without, arm run aide by side. In this type of testing both circuits process the same ore so that valid results occur sooner than with aerial testing. The data may be averaged before testing or the differences in the performance indices may first be calculated before averaging. However, the two circuits must be nearly identical in their mechanical characteristics otherwise differences other than the degree of control will bias the results. It mechanical differences exist than it my be necessary to adjust one or the circuits prior to testing. Sometimes it is possible to correct far mechanical differences based on Inherent efficiency calculations made with a model. Hypothesis Testing Once the data is collected, hypothesis fencing can be carried out to determine if the automatic control system has resulted in a statistically significant improvement. One can construct a histogram of the distribution or performance indices with am without control such as Figure 1, or the

Jan 1, 1991

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By F. G. Miller

To improve coal flotation Bethlehem Steel Corporation's Research Department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies5 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the bas is for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14M x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level.

Jan 1, 1968

By Frank H. Skelding

A new, large mine is about to be born. Many years and millions of dollars have been invested in exploration. An orebody has been found and proven. All necessary political and legal work to establish rights and conditions for development are complete. The feasibility studies are favorable. Financing has been arranged. Board approval has been given to proceed. The time has come to engage a contractor to design and build the new facilities in a location, as is the common case today, far re¬moved from the centers of advanced technologic development where the minerals will ultimately be used. A select list of Engineering and Construction (E&C) companies is asked to prepare proposals. At this point the common viewpoint among mining companies is that the company's sole remaining problem, a major one to be sure, is to select qualified contractors to design and build the project at the lowest cost and shortest time possible so that production can start generating a return on investment. The purpose of this discussion is to explore the viewpoint of the large E&C contractor toward such projects. It differs in important ways from that of the client mining company and it is these differences and the reasons for them that must be understood by the client if severe difficulties and misunderstandings with the contractor, starting at the beginning of contract negotiation and continuing through design and construction to final startup are to be avoided or minimized. Often enough, the difference is in degree, not kind, which only serves to obscure the fact that a difference exists.

Jan 1, 1975

By R. E. Driscoll

The exploration, geologist of necessity has to have a wide working knowledge of many specialties other than hiw own, First he has to use his own technical background to find a deposit,, of a mineral that is of interest, Once found, his problems are Just beginning, He then has to assume the role of an economist, an accountant, a mining engineer, a chemist, a metallurgist,, a salesman and what-have you, In the economic field, he must determine the marketability of either the ore or the refined mineral. He must gauge the supply and demand for the particular mineral he is interested in and make his best guess as to ultimate cash flow from a deposit over the estimated life of said deposit, He must then assume the role of a mining man and estimate cost of recovery, including an, evaluation of the most economic mining method, cost of supplies and labor, and again estimate a net cash flow. He must then determine amenability of ore to economic metallurgical methods, he must determine the legal status of the property involved and, after analysis of the specific situation, determine the best approach to a deal, After all of this he must sell it to the people who will put up the money and then put his deal together and sell it to the people who own the minerals, if that be necessary. Then he has to sit back, with crossed fingers and crossed legs wondering for some months, and in many cases even years, whether or not he is right. The expenditures required to open up a mine in this day of wild inflation are such that he has to be right, and the responsibilities are awesome.

Jan 1, 1958

By Donald R. Lamont

The paper outlines the reasons for and research behind the recent decision to adopt oxygen decompression in the UK. Currently used measures of decompression illness are critically appraised. The paper describes the main precautions to be taken on site to manage the fire risk from the use of oxygen underground. A summary of the initial results from the use of oxygen decompression in the UK is presented.

Jan 1, 2003

By R. Brown, A. J. S. Spearing, M. Treinen, M. Theisinger

The mining and use of coal creates a significant amount of waste material that needs to be safely disposed of. It is likely that in the medium term, the Environmental Protection Agency (EPA) in the U.S. will categorize all such products as a new category – special waste. This would make the materials subject to many of the requirements for handling toxic waste, which will complicate the disposal of such products and significantly increase the disposal costs. Underground disposal would, therefore, seem to be the obvious solution, especially if the placed material can have low or no permeability, so that water table pollution does not present a serious long-term issue after placement. Significant additional advantages could be derived from this backfilling, including the reduction or elimination of surface subsidence, increased extraction, reduced surface waste disposal footprint and the elimination of explosion-proof seals in worked out areas. The research using a specific coal waste product as a typical example proved that the method of placing the backfill at a high density with low permeability is technically viable, but it must be made more cost effective and the other potential benefits quantified and costed in order to present a true comparison.

Jan 1, 2010

By M. Li, J. K. Thompson, A. S. Azman

"Powerful mining systems typically generate high-level noise that can damage the hearing ability of miners. Engineering noise controls are the most desirable and effective control for overexposure to noise. However, the effects of these noise controls on the actual hearing status of workers are not easily measured. A tool that can provide guidance in assigning workers to jobs based on the noise levels to which they will be exposed is highly desirable. Therefore, the Office of Mine Safety and Health Research (OMSHR) of the National Institute for Occupational Safety and Health (NIOSH) developed a useful tool to estimate the hearing loss due to occupational noise exposure in a systematic way and evaluate the effectiveness of developed engineering controls. This computer program is based on the ISO 1999 standard and can be used to estimate the loss of hearing ability caused by occupational noise exposures. In this paper, the functionalities of this software are discussed and several case studies related to mining machinery are presented to demonstrate the functionalities of this software. INTRODUCTIONPeople regularly exposed to noise can develop hearing loss at different levels of severity depending on a number of factors. The resultant hearing loss can affect one’s ability to understand speech, learning, acoustic signal perception, or appreciation of music. Hearing loss caused by overexposure to noise has long been recognized in literature. However, it still does not get serious attention by those working in noisy environments because the loss of hearing ability is a gradual process and workers are often unaware until the damage becomes an apparent problem. In the United States, occupational hearing loss is one of the most common work-related illnesses. Depending on the definition of exposure and impairment, in 2012 the National Institute for Occupational Safety and Health (NIOSH) estimated that there are between 5 and 30 million workers in the U.S. who are exposed to noise levels at work that put them at risk of hearing loss.4 In the mining industry, noise-induced hearing loss (NIHL) is particularly severe due to the fact that heavy-duty machinery is widely used to improve production efficiency, and this machinery can generate much higher-level noise than the permissible level defined by regulation. As a result, the mining sector has the highest prevalence of hazardous workplace with high noise exposures (76%) among all industrial sectors."

Jan 1, 2015

By P. D. Lafleur

A concerted effort to determine the quantities and effects of trace elements in the environment requires the application of a number of different analytical techniques in the same or in different laboratories. The interpretation of analytical data is often difficult because of differing results between analysts or even by the same analyst at different times. Standard Reference Materials (SRM), which are certified for their trace element content and are in a matrix similar to the one of interest, can greatly increase the accuracy of analysis and the reproducibility between laboratories. The United States National Bureau of Standards (NBS) has developed a number of SRMs applicable to the determination of trace elements in environmental materials. Two of these, SRM-1571, Orchard Leaves, and SRM-1577. Bovine Liver, are excellent for biological tissue analyses. Several new standards are of value for fossil-fuel analyses. These are: SRM-1632. Trace Elements in Coal; SM-1633, Trace Elements in Fly Ash; SM-1634, Trace Elements in Residual Fuel Oil: and SRM-1635, Trace Elements in Gasoline. In cooperation with the US Environmental Protection Agency, the NBS has recently concluded an interlaboratory comparison involving analyses by more than 60 laboratories on these fossil-fuel materials. The resulu of this intercomparison and the broad range experience with the biological materials will be presented showing both intratechnique and intertechnique variations, and the sensitivities and comparisons with the values certified by NBS.

Jan 1, 1975

By R. W. Wittkopp

The Relief Canyon gold deposit is located approximately twenty- four kilometers east of the town of Lovelock in Northwestern Nevada. At Relief Canyon, the Late Triassic Grass Valley Formation has been thrust over the Late Triassic Natchez Pass Formation. The lower plate Natchez Pass Formation is composed of massive gray dolomitic limestone which is locally silty and sandy. The upper plate Grass Valley Formation is composed of shale, siltstone, argillite and quartzite. Gold mineralization at Relief Canyon occurs along the highly brecciated thrust contact between these two formations. Weak gold mineralization often occurs above the thrust in the Grass Valley Formation, however, most of the ore grade mineralization is present below the thrust in the brecciated Natchez Pass Formation or where the two formations are mixed as a result of movement along the thrust. Several types of gold mineralization have been recognized at Relief Canyon. A large amount of the ore is present as a jasperoid breccia, however, significant amounts of ore occur as a mixed breccia composed of upper plate rock, fresh limestone, clay and jasperoid breccia. Gold ore also occurs in a fresh limestone breccia which contains a large amount of clay. Below masses of jasperoid, jasperoid stringers containing gold extend into the fresh limestone. Gold mineralization at Relief Canyon appears to be truly disseminated and has the typically associated trace elements of arsenic, antimony, mercury and fluorine. The Relief Canyon deposit can be classified as a structurally controlled disseminated gold deposit. Other deposits that fit this classification are the Pinson and Dee gold mines.

Jan 1, 1984

By J. W. Leonard

Introduction Gravity-based coal/mineral preparation plants must be operated to yield products of a quality satisfactory to existing markets. However, because of historic control problems, recovery is frequently sacrificed to achieve quality, resulting in losses of valuable product. Plant control has ranged from intuitive in-plant spot quality judgments made by various operators to gross methods involving such devices as density gauges, floats, grabsample on-the-spot sink/float tests, etc. Millions of tons of quality coal/minerals are lost to refuse each year, because of the historic lack of a continuous and dependable control system. The result is serious economic, as well as environmental, losses. While the economic losses are obvious, the less obvious environmental ones, in the case of coal, result from the misplacement of more ignitable quality fuel to refuse banks. Until recently, a control system capable of supplying a market-grade coal/mineral product, while continuously minimizing product losses to refuse, has been technologically unavailable. Coal/Mineral Washing Tracer System Performance Monitor (CMWTSPM) The first Coal/Mineral Washing Tracer System Performance Monitor (CMWTSPM) originated in the late 1970s as an innovative idea and ultimately resulted in Leonard Patent No. 4,345,994 issued on August 24, 1982. In a classic example of successful university basic research, the patent was followed by two US Department of Energy (DOE) merit awards for fundamental optimization research at the University of Kentucky, a number of publications, a successful applied research program (underwritten by SENTREX at Irvine, CA) and field tests at the Rochester and Pittsburgh Coal Company Keystone Mine near Indiana, PA. The system is now operational and is marketed by SENTREX as the SENTREX Performance Monitor. A diagram of the system is shown in Fig. 1. This system relies on metal detection as the basic tracing medium. Since it is capable of tracing particles as fine as 0.19-in., the system is ideal for coarse coal/ mineral cleaning processes. Basically, the CMWTSPM records the distribution of synthetic coal/mineral particles, of known size and specific gravity, between product and refuse output streams of coal/mineral washing, gravity-concentrating processes. For any given particle size, surface area and shape are constant. The particles are [ ] designed to find their way into the center of their respective inprocess specific gravity/size streamlines. The system will yield a complete partition curve to show the percentage of misplacement for any selected size/specific-gravity particle fraction, thereby providing a point-to-point insight into process failure. When used to evaluate operational processes, this full partition curve is far more diagnostic than the simplifying, derivative, single index number known as the Ep value. The Ep value is commonly used for convenience to represent symmetrical partition curves, but, if the actual partition curve is non-symmetrical, use of the Ep value can result in serious diagnostic error. While the Ep is useful in design and for rapid performance evaluation and process adjustment, the full partition curve is by far the more diagnostic. It will provide insight into the behavior of particulate flow, through non-symmetry, as a means to highlight potential systemic failures. Performance of the process is measured and improved by determining the extent of particle misplacement and by making timely adjustments to the unit to reduce the misplacement. Used in this manner, the CMWTSPM is not only a long needed processing control monitor, but it is also a very powerful diagnostic tool which, in the hands of skilled operators, has

Jan 1, 1993

By Peter J. Huck, Swpan Bhattacharya, Madan M. Singh

This paper reviews the state-of -the-art techniques for estimating the duration of post- mining subsidence arising from different mining techniques and evaluates existing post-mining liability systems in the United States and abroad. For each mining technique (room-and-pillar and longwall) the mechanism of subsidence development is examined and the critical factors influencing the duration of subsidence are evaluated. These are followed by a comprehensive summary of field data on the duration of subsidence movements collected in various parts of the world. Using this information, graphical charts are developed to depict the relationship between the time duration and critical controlling factors. Also included are any mathematical relationships that may exist between the different variables. Finally, a survey of current state, federal and foreign legislation on mine operator liability time spans is provided. These laws are evaluated for their applicability in light of the data on duration of residual subsidence. On the basis of this evaluation, guidelines are suggested for the establishment of the mine operator liability structure for the United States.

Jan 1, 1986

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By Gary L. Simmons

Over the past several years, Newmont Gold Company (previously Santa Fe Pacific Gold Corporation) developed a new technology for the flotation of refractory auriferous sulfide minerals which is referred to as the N2TEC flotation process. Starting in April 1997, the first commercial flotation plant utilizing N2TEC technology was successfully commissioned at the Lone Tree Mine near Valmy, Nevada. The Lone Tree flotation plant was designed to process 4,085 mt/d of ore producing 494 mt/d of sulfide concentrate. A flotation tails leach CIP circuit was added to recover cyanide-soluble gold from the flotation tails. A portion of the flotation concentrate is blended with whole ore feed to the Lone Tree autoclave, up to the limit imposed by the current oxygen plant capacity. The remainder of the concentrate is shipped to either the Twin Creeks autoclaves or the Carlin roaster for subsequent oxidation and gold extraction. This paper discusses the results achieved in the commercial flotation plant compared to pilot plant testing and engineering design flotation modeling. Capital and operating cost information are also presented.

Jan 1, 1999

By Vladimir Nikolić, Alex Doll

The Bond ball mill grindability test is one of the most common metrics used in the mining industry for ore hardness measurements. The test is an important part of the Bond work index methodology for designing and measuring the efficiency of mineral grinding circuits. In spite of being called “Bond’s Law,” the work index equations are not a law of nature; but rather an empirically measured regression of a large data set collected by the Allis- Chalmers corporation in the period between 1930 and 1952. As a regression, it is valid within a specific “calibration space,” and great care is required when deviating the test procedures or observing results that are outside of that calibration space. This paper is a collected summary of other works by the Authors that describe feed sizes, product sizes, quality control checks, and other information about interpreting the test and using its results. Examples of adjustments that are sometimes required when using the test are: changing the test product (P80), and coping with a feed that is too fine to apply the “proper” feed preparation steps (such as is sometimes observed from HPGR or SAGDesign product testing). Related metrics, like the Morrell Mib value and Levin B value will be discussed, along with recommendations for their use on design projects. The intended audience is any user of laboratory work index test data.

Feb 1, 2024

By Hugh Douglas

This paper discusses the financial health of the U.S. mining industry and its ability to meet the future raw material requirements of this country in the context of resource independence. The title of this paper begs several questions, and three will be raised here. The answers to them will form the basis for discussion. The three questions are: What does one mean by resource independence. How is the U.S. mining industry defined. How is financial health measured.

Jan 1, 1977

By C. W. Schultz

Earlier publications from The University of Alabama have indicated that column flotation performance is improved when operating at low pulp levels and when the feed is directed into the froth phase. To validate these early observations a series of tests were performed in which the position of the feed entry to the column and the pulp-froth interface were systematically varied. The optimum grade-recovery relationship was achieved with high feed entry (WA) of column height) and very low pulp levels (<10% of column height). The position of the pulp-froth interface appears to be the more critical variable. When operating in this mode (1. e. at low pulp levels) column flotation becomes. in reality. a froth separation process.

Jan 1, 1991