Search Documents

By A. D. S. Gillies

Diesel engine particulate matter pollution is a matter of concern currently in underground mines worldwide. A number of real-time Diesel Particulate Matter (DPM) monitors have been developed in recent years; two of these by the National Institute of Occupational Health and Safety (NIOSH) in the US. One, the D-PDM, is based on an adaption of the successful NIOSH?s Personal Dust Monitor (PDM) unit which is being taken up very successfully for mine respirable dust monitoring. The D-PDM measures all particulate matter within a sub-micron range as classified nominally at 0.8 micrometers by a purpose developed cyclone. The other, the FLIR Airtec, measures the Elemental Carbon (EC) component of DPM by a laser scattering approach. Both instruments have been evaluated underground in robustness and reliability testing in coal mines by the authors. Real time DPM monitors allow greater understanding of the sources and levels of DPM pollution in underground activities. They allow engineering evaluations to determine how conditions can be improved or mining personnel relocated to lower concentration levels. Studies are discussed that examine DPM concentrations from vehicles under varying ventilation conditions. Some of these concern tests undertaken during high activity longwall face moves. They focus on evaluating DPM during the various phases of the face Chock Shield moves. An initiative in some mines has been to limit the number of vehicles in the mining section or panel by the use of a Tag Board or Traffic Controller at the panel travel road entrance to manage exhaust DPM and gases. Diesel tags or tokens are used to control the number of vehicles entering a section or panel and so limit level of pollution. Summation of DPM levels from points monitored throughout a panel demonstrates increasing DPM levels from influence of additional equipment in series within the ventilation circuit. An alternative approach is to invest in underground continuous real-time monitoring of exhaust gases, DPM and section air quantity and integrate this information to determine whether an additional vehicle can enter without exceeding diesel target limit. This optimizes the access of diesel vehicles and replaces the existing manual tag board system. Real-time DPM monitoring allows the industry to pin-point high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. Identification of high DPM zones allows efficient modification of mine ventilation, operator positioning and other work practices to reduce underground miners? exposures.

Jan 1, 2012

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By Nathaniel Arbiter

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give constant power numbers in liquid' systems indicating that they operate under fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufactures. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations.

Jan 1, 1968

By K. W. Harris, K. A. Perry

Reserve depletion in Central Appalachia is continuously creating unique ground conditions for underground coal mines with many of these difficult environments directly attributable to multiple seam mining and/or deeper overburdens. While many empirical studies have been performed in an effort to improve understanding of these problems along with potentially improving safety and extraction, many of the difficulties encountered lie outside of the normal realm of expected behavior. This is often the case when mining in bump prone ground, where additional concerns are introduced and design buffers are warranted. The boundary element software LaModel was used to study three bump events in a deep-cover, multiple-seam reserve located in Harlan county in the Kentucky region of Central Appalachia. This region is notoriously bump prone due to significant areas of deep cover, the presence of strong to massive lithology (such as sandstone), and an extensive history of underground mining that increases the probability of multiple seam interactions. Multiple seam interactions are best understood with respect to site-specific parameters, including both the geological and geometrical components of interburden, overburden and mine workings. Initially, empirical-based approaches (ARMPS/AMSS) were used when attempting to back-analyze the bump events. However, it was recognized that a more detailed investigation was necessary to understand the fundamental causes/conditions associated with the bump events. Consequently, the LaModel study resulted in a mine-specific calibration method for the reserve. With this method in place, enhanced bump prediction throughout the reserve is expected, such that the stability, recovery and safety of future mining may be improved.

Jan 1, 2014

By Yukika Miyashita, Takahiro Inoue, Kenji Namikawa, Masashi Matsumoto, Junichi Koseki, Yoshihiro Terashima

"In order to construct an underground two-layer expressway branch junction structure with a height of 14.7 m and a width of 22.3 m, two shield tunnels in each layer were combined by using a non-cut-and-cover enlargement method in sedimentary soft rock. Before and during the construction work, preliminary analysis, in-situ investigations and laboratory tests were conducted to ensure the construction safety and to evaluate the deformation characteristics of sedimentary soft rock. The construction project was safely executed without any water leakage or collapse of tunnel working face. The predicted results from preliminary analysis were almost similar to the measured values. From the detailed investigation of measured results, it was confirmed that the deformation characteristic of the sedimentary soft rock was observed to a small extent as the ground deformation derived from construction work. INTRODUCTION In recent years, some newly constructed urban expressways in Japan are being planned as underground structures due to the consideration of roadside environment. The construction of such underground expressways is frequently conducted using a shield tunneling, a typical one of non-cut-and-cover methods, to prevent any adverse effect to traffic in arterial roads, operation of nearby commercial establishments, and daily lives of local residents during construction work. For underground urban expressway, the connections with existing road network on ground surface or on elevated sections are indispensable, which require the construction of an underground branch junction with large cross-section. This raises a technical difficulty regardless of the open-cut or non-open-cut construction method."

Jan 1, 2016

By B. Holen, J. R. Baregi, J. A. Organiscak, A. B. Cecala

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-µm respirable size particulates under various HVAC airflow operating conditions.

Jan 1, 2015

By A. H. Sharbaugh

It is believed that considerable economic benefit would arise if run of mine (ROM) coal from the underground mines in the Winifrede seam could he enriched before shipment to the preparation plant by partial removal of the shale. Shale could comprise up to 50% of the ROM product. Complete mine-mouth separation is not necessary, but any process must be dry and have high Btu recovery. We have conducted a preliminary analysis of coal/shale mixtures from the Winifrede seam and we find that it is quite possible that a 50-50 ROM mixture of coal and shale could be converted to a 60-40 coal-shale mixture by inspection of individual lumps coming from the mine. The device would consist of a feeder/siever section to deliver the ROM coal > 5 cm (2 in) to an inspection station via a conveyor belt. This inspection station decides if a piece is coal or shale, and if it is shale, activates an air jet to blow shale off of the belt. We have evaluated a dielectric loss technique for the inspection device. The potential advantages of the dielectric loss method are high throughput, low capital cost, and no special handling or licenses would be required. Such a single lump inspection technique is made possible because of advances in high speed electronics and servo systems. This paper provides a summary of our analyses on the Winifrede coal sample, a description of a proposed apparatus to separate coal from shale, some of the experiments needed to demonstrate our ideas.

Jan 1, 1984

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

By Joern Katzer

It is vitally important to any tunnel project to have an accurate and reliable survey control network inside the tunnel for layouts, as-built surveys, and to provide guidance to the tunnel boring machine (TBM). However, the concepts and methodology to provide such a survey network are sometimes not well understood. For example, the first anticipated survey task that takes place during the bidding process is often ignored, which is to provide a comprehensive survey network preanalysis for the surface network and tunnel traverse based on survey statistics that will be used to make informed decisions on the survey requirements and methodology. Instead, these steps are often only vaguely based on previous results and prior tunneling experience. But each tunnel is different, and a solution that worked for one tunnel project might be unsuitable for another. The purpose of this paper is to provide tunnel project engineers, managers and surveyors with the general concepts for tunnel survey methodologies and examines several statistical tools for a basic horizontal and vertical tunnel survey preanalysis. These survey statistics tools provide useful estimates of the expected lateral and vertical tunnel traverse accuracies, but are not a replacement for a comprehensive tunnel network preanalysis. The proposed formulas do not take centering errors into account, are using average distances for each traverse leg, and assume that the survey data is free of outliers in the measurements. It is very important that the estimated instrument accuracy is based on true values that are reflective of measurement precisions that are actually achievable inside the tunnel to provide accurate results.

Dec 1, 2022

By Richard M. Tinlin

The mining industry needs to assure compliance with the Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500). Congress has enacted this legislation with the intent of preventing, reducing, and eliminating pollution of the nation' s surface and groundwaters. Recognized sources of pollution such as seepage from tailings ponds, waste dumps, and contaminated effluent from mine dewatering operations pose a serious threat to adjacent groundwaters. In addition, technological innovations being implemented by the industry such as in situ leaching of low grade ore deposits may also lead to ground- water contamination. An adequate monitoring methodology designed to meet the needs of the mining industry is needed. Monitoring and control methodology devised for other man- caused sources of ground- water pollution - e. g., landfills - offer considerable promise for adaptation to the problem. The prediction of deleterious effects on groundwater quality usually requires extensive geohydrological data in addition to a thorough analysis of the mining activity that is underway or projected. If the avail- able data are adequate, mathematical models of surface and groundwater flow can be constructed that will help to predict effects on water quality. Data are inadequate to allow a realistic interpretation of pollution potentials. These data can be supplemented by computer simulation as a method to explore a number of possible environmental effects and also to develop a minimum-cost approach to identifying and gathering the additional necessary supporting data. Incorrect assessment of the important environmental considerations may, in many instances, prove to be the weakest link in analyzing the financial feasibility of a mining operation.

Jan 1, 1973

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products, The original source of potassium was wood ash (hence the name potash), However, today the term potash refers to all commercially important salts of potassium. Sylvite, usually found associated with halite, is the predominant economic potash mineral; carnallite a lesser important source of potassium chloride, while langbeinite is important as a source of potassium sulphate. The world's first potash mining operation commenced in Strassfurt, Germany about 1860, Since that time the industry has grown steadily to its present annual volume of about 30, 000, 000 tons of potassium chloride products or 18, 000, 000 tons of K2O equivalent, potassium chloride or "muriate of potash" being equivalent to 63. 1% pure K2O, WORLD POTASH RESERVES ARE NOT EVENLY DISTRIBUTED The earth's crust contains 2 to 3 per cent potassium, mostly in the form of insoluble silicate minerals. The economically important deposits, however, are formed from brines concentrated by evaporation. The world's most important commercial deposits are of Devonian and Permian age, however soluble potassium bearing salts are presently being concentrated by evaporation in several drainage basins, notably Searles Lake, California, Great Salt Lake, Utah' and in the Dead Sea. At least twenty-four countries are known to have reserves of potash: Canada and the USSR have over 80% of the presently known world reserves, (Figure 1)

Jan 1, 1972

By James S. Browning

Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama. 1, 2, 3 Whereas in western North Carolina these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites.4 To a lesser extent, mica is produced as a byproduct of feldspars and spodumene.6 Past research by the Bureau of Mines has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica." This method requires thorough desliming of the ore with consequent fine mica losses. The other method utilizes an alkaline-anionic-cationic process for recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica. 8, 9, 10, 11, 12, 13 The latter process has also been successfully applied to a micaceous schist ore from California.14 This report summarizes the results of these research studies. Both of the flotation processes developed by the Bureau of Mines have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores.

Jan 1, 1969

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By Joseph J. Garbarino

World demand for phosphate fertilizers has grown at an average annual rate of between 6 and 7 per cent over the past 10 years. In the next five years world demand is expected to at least continue to grow at that rate. Also, the continued need for improved fertilizer materials, coupled with improvements in fertilizer technology, have placed added importance on the use of phosphoric acid as a starting material for high analysis phosphate fertilizers. This demand for phosphates and phosphoric acid must be met by increased production. Increased phosphoric acid production also brings increased demand for chemical processing agents including foam control agents. We at Arizona Chemical Company have closely followed the phosphate fertilizer industries needs. Arizona Chemical Company has been an important supplier of flotation agents to the phosphate industry, primarily from its Panama City, Florida plant. We have also recognized the important role played by foam control agents in the wet-phosphoric acid manufacturing process. We feel it is the responsibility of the supplier of foam control agents to offer specifically designed products that are highly efficient and economically useful. The difficulties involved in evaluating foam control agents in the plant are recognized. Owing to the large number of variables present, and the difficulties in controlling these variables during the period of a plant trial, plant evaluation of a large number of foam control agents is impractical. We have attempted to develop a practical, reproducible, and yet rapid, laboratory evaluation test which correlates with plant performance.

Jan 1, 1966

By John M. Moore

Within the Pofadder district of Namaqualand, South Africa, economically exploited deposits of bedded barite and zinc-lead-silver-copper sulfides occur in close proximity within highly metamorphosed mid-Proterozoic pre-tectonic para¬gneisses of the Namaqualand Metamorphic Complex (NMC) (figure i). The paragneisses belong to the Bushmanland Group (SACS, 1980) that comprises a relatively straight-forward regional sequence of basal leucogneisses, intermediate mica-sillimanite schists and glassy quartzites, and a mixed upper zone of banded iron formations (BIF), minor marbles, quartz muscovite schists and localised uppermost quartz-pebble conglomerates and amygdaloidal mafic gneisses (Joubert, 1974) (figure ii). The base metal and barite mineralisation occurs in close association with BIFs, generally above the glassy quartzites, although in some cases possibly below them. In the regional context, the Bushmanland Group paragneisses are, to the north, intercalated with and ultimately replaced by meta-volcanic sequences of talc-alkaline affinity (Reid, 1977) belonging to the Orange River Group (SACS, 1980). The metavolcanics are generally of acidic to intermediate composition and show evidence of subaerial formation from 'high altitude shield volcanism' with many acidic ashflow and welded tuff bands, mesocratic and lesser melanocratic lavas and some fanglomerates (Ritter, 1980). To the south and east, the schist/quartzite associations are initially intercalated with and eventually replaced by cordierite gneiss/metacarbonate/biotite gneiss associations of shallow marine affinity (Moore, 1980a). The Bushmanland Group paragneisses appear to represent sedimentary material in the extreme distal portions of a talc-alkaline volcanic environment adjacent to a shallow platform sea.

Jan 1, 1983

By R. A. Seitz

This paper presents a framework for analyzing the theory and industrial practice of coal flotation and gives some examples of its use for understanding flotation phenomena and optimizing/controlling flotation circuit performance. It is based on extensive laboratory and in plant test work conducted over the past several years by researchers at MTU as well as an analysis of the literature. Previous researchers have usually considered either the surface chemistry or the kinetics of coal flotation behavior, only rarely have these factors been considered together. However, these factors must be considered together in order to gain a clear understanding of the theory underlying coal flotation such that its practical application can be optimized. Fortunately, this complex objective can be achieved by considering the recovery and rate of recovery of the different types of particles present in the feed to coal flotation circuits and the fundamental mechanisms responsible for these recovery phenomena. The influence of three major groups of variables must be considered: control variables (reagent additions, aeration rate, etc.); disturbance variables (feed pH, percent solids, etc.); and circuit design variables (number of cells, circuit arrangement, etc.). Each of these groups of variables affects process kinetics in a clearly understandable manner, which, once determined, is extremely useful in circuit design and optimization. This paper includes a discussion of the use of the proposed framework to explain the effects of some coal characteristics on flotation performance. In addition, an example of using this analysis to optimize the performance of a coal flotation circuit using frother and collector addition levels is included.

Jan 1, 1985

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By A. W. Khair

This paper presents an analysis of respirabie dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.

Jan 1, 1985