Search Documents

By Richard V. Beck, Donald R. East, Jeremy P. Haile

In view of the increasing use of heap leach operations in the mining industry and the critically important performance of the leach pad liner in both the economic and environmental aspects of the design, it has become essential that the designer fully understand the factors affecting the performance of the liner. Minimizing the loss of pregnant solution through the leach pad liner is obviously of paramount importance to the economic efficiency and environmental compliance of the heap leach operation. Losses through the liner are a function of the hydraulic conductivity of the liner material and the hydraulic gradient across the liner. This applies to both natural and synthetic materials. The hydraulic gradient across the liner is a function of the build-up of solution above the liner, which in turn is determined by the permeability of the heap material, the slope of the liner, the drainage path length and the leachate infiltration rate. A relationship incorporating each of these parameters and their effect on the hydraulic head acting on the liner has been developed in terms of the Dupuit criterion, assuming one- dimensional flow with vertical accretion.

Jan 1, 1987

By P. Malozemoff

Discussion by P. Malozemoff I have no objection to using mathematics in the value appraisal of properties. The factor that is not emphasized in the paper is that very few important properties have a lifetime that reflects the initial ore reserves of the property divided by the rate of production adopted. In the majority of cases, major properties mine out several times the initial reserves. How much more will be mined out is not known, and only exceptionally gifted geologists can predict that additional reserves will be found. There is the further factor of metals price, which, over the long term, is not predictable. Another factor vitiating making calculations on initially established ore reserves is the speculative nature of exploration success. In my judgment, the life of a property, in addition to an established ore reserve, should include ample time for exploration to find additional reserves. The likelihood of additional reserves is based on the geological promise of the general area where the mine is established. This is especially important because of various risk factors associated with small orebodies, the economic life of which is about five to seven years. In underground mines, it is not economic to develop reserves beyond a certain depth, so the life of initially established reserves must be limited. In these cases, it is especially important to have a good geological understanding of the orebody and its continuity. To accommodate these concepts and present proof of economic soundness for a mining enterprise, a mathematical analysis should yield a life long enough to allow exploration and the development of additional reserves that would ensure a longer mine life and a more profitable result.

Jan 1, 1994

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987

By E. O. Mixon, Joseph P. Sehulster

This paper describes the driving of a 1421 m long by 2.74 m diameter sewer tunnel in postglacial soils of the Menomonee River Valley in Milwaukee, Wisconsin. An earth pressure balance machine was used for excavation and to install a "one pass" pre-cast concrete gasketed segmental liner. Also discussed is the use of ground freezing to stabilize the ground for the start of tunneling operations and modifications made to two structures to accommodate final tie-ins for the sewer tunnel.

Jan 1, 1989

By Rebecca A. Miller, Terry M. Hertel

In-pit identification of neutral waste rock at the Zortman and Landusky minesites in Montana, by visual and chemical analy­ses, will assist in proper segregation and placement of rock so that soil and water resources can be protected. The use of too few or very general segregation criteria to identify neutral waste rock can result in ineffective waste rock segregation. Conversely, the use of overly restrictive criteria can result in the unnecessary loss of valuable reclamation material that would otherwise have to be mined elsewhere and hauled to the site. Recognition of nonre­active materials can be accomplished on a site specific basis with the use of visual observation and simple chemical analyses. The choice of chemical parameters used to analyze rock samples is constrained by the length of time needed to conduct the test. These analyses must require no more than 24 hours to complete so mining can proceed without delay. Limits set for the chosen parameters must be reasonable and defensible. To achieve these objectives over one thousand samples were collected at the Zortman and Landusky minesites and clas­sified by rock type, total sulfur content, paste pH, and net neu­tralizing potential (NNP). In addition, over 22 humidity cell kinetic tests were conducted to help corroborate static results for waste rock. Another 8 humidity cells were configured in series to test waste rock blending and waste rock/limestone capping alternatives as mitigation for acid rock drainage. Leachates were analyzed for pH, conductivity, alkalinity, acidity, sulfate, Al, Cd, Cu, Fe, Mn, Zn, Mg, and Cr in some cases. Petrographic analysis, as well as total sulfur content, paste pH, and static and kinetic test results identified three geochem­ically different waste rock groups: 1) Archean amphibolite gneiss and Paleozoic carbonates and shales, 2) Tertiary syenite porphyry, and 3) other less abundant Tertiary igneous and Archean metamorphic rocks.

Jan 1, 1996

By G. S. Grainger, R. A. Cummings, F. S. Kendorski, R. L. Butts

Georgia Power Company's Rocky Mountain Project, located approximately ten miles northwest of Rome, Georgia, in the Valley and Ridge Physiographic Province, is a pumped-storage facility rated at approximately 800 megawatts of peaking energy. Geological field explorations and borings enabled the division of the rocks along the tunnel and shaft alignment into distinct lithologic units and defined the ground--water regime. Field explorations included a detailed analysis of the rock mass discontinuities at available rock unit exposures. Testing of rock strengths was performed in several phases in both the field and the laboratory. The field testing consisted of point-load testing, geophysical testing, in situ load testing, and hydro-fracture testing. Laboratory testing determined the Brazilian split-tensile strength, the unconfined compressive strength, the triaxial compressive strength, the joint-direct shear strength, and the pulse velocity. The rock mass along the tunnel and shaft was also characterized by empirical classification systems. The classification systems included the Rock Mass Rating (B1IR) and the Rock Mass Strength Determination (RHSD). The results of the field explorations, field testing, laboratory testing, and rock classifications were used to divide the rocks into two structural groups. These rock groups were defined as volumes of rock wherein the rock mass behaves similarly in response to the excavation. Each group, therefore, required separate rock engineering consideration.

Jan 1, 1986

By Edward M. Belsky

Increasingly stringent government environmental regulations will affect the availability and costs of bonding and insurance products for the mining community. New regulations requiring Environmental Impairment Insurance, Reclamation Bonds, and Cyanide Use Bonds will result in both an increase in cost and a decrease in availability of affordable insurance and bonding pro- ducts. Professional Liability Insurance for engineers that covers pollution exposures will be a must for all professional engineers working in the mining community. By understanding the problem, solutions can be structured to allow your company to obtain the mandated insurance at the most favorable cost and conditions!

Jan 1, 1991

By Robert S. Post

A highly respected coal mining company in West Virginia updated their stacker belt by switching to a new magnetic coupling. The savings they achieved are the subject of this paper. A steep incline and heavy belt loads are powered by a dual drive arrangement. The magnetic couplings were custom designed for complete fluid coupling retrofit and easy installation in the field. Maintenance personnel updated the drives in just a few hours. Over the following several weeks, adjustments were made to the couplings for optimum performance. Cost savings are found in reduced down time, no coupling maintenance, and equipment protection.

Jan 1, 2000

By G. V. Basham

"Environmental audit" is a phrase that can raise the blood pressure of otherwise cool and calm corporate personnel. There is widespread concern that any organized effort to find environmental problems will do so and may result in the imposition of substantial liability against the business that engages in such activities. However, such audits can reduce rather than enhance possible liability. Relevant issues include: the role of the attorney in the process, liability risks associated with environmental audits, steps to maximize confidentiality of audit results, reporting requirements and use of audit results in a proactive manner.

Jan 1, 1995

By Michael G. Nelson, Brandon J. Peterson

Currently, decisions made by mine management are usually based on economic analysis and predetermined rating systems and tables. As financial and other constraints on mining operations become more severe, more accurate methods are required. Discrete-event simulation programs have been used successfully in many mining applications, including the simulation of open-pit, truck-and-shovel operations. However, these simulations could not model complex systems well enough to provide the detailed modeling of the haulage roads and other mining operations that is needed today. The recent advances in computing technology combined with the recent abilities of simulation to realistically simulate complex systems and visually present results in 3D have made simulation a more detailed and valuable aid in the evaluation of mining projects.

Jan 1, 2002

By C. Patrick, T. Combs

The purpose of this paper is to provide a method for analyzing the sequencing of mining production processes and predicting the effects of any planned changes. Included is a description of the development and utilization of a project-scheduling simulation that combines analytical scheduling with stochastic-activity durations. The simulation is demonstrated in two realistic examples: a longwall face-to-face transfer sequence and the effect of varying advance rates on longwall development sections. Statistical data that can provide a basis for more informed production decisions are generated in the form of project activity/path criticality and project-duration distributions. In both examples, a quantitative risk assessment, regarding subjective decisions in underground production sequencing, is presented.

Jan 1, 1996

By T. V. Vasudevan, J. Blaakmeer

Adsorption experiments were conducted at two different solid loadings to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region 11, while surface precipitation was predominant in region I11 along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1988

By A. K. Ghose, S. Chakraborti

The research work outlined in this paper examines the utility of index tests for evaluating the strength of coal, both in the laboratory and in-situ. For routine evaluation of strength and deformation properties of coal seams, as inputs for design in stability analysis and equipment selection, the index tests are cost-effective and also make less demand on time and manpower. Four index tests, namely Protodyakonov Index, Cone Indenter Index, the Point Load Strength Index and Schmidt Rebound Hammer, were evaluated for 13 coal samples and correlated to fundamental strength and deformation properties such as uniaxial compressive strength, Brazilian tensile strength and modulus of elasticity of the same coal stratum. The index tests, barring Point Load Index, showed relatively low percentage scatter compared to the fundamental strength and show marked advantages for routine estimation of coal seam strength.

Jan 1, 1986

By J. Roufagalas

Sustainable development requires that exploitation of environmental resources is such that it does not result in permanent damage to the environment. In many instances environmental damage is an external cost of the entity exploiting the resource. Ideally, the entity should be forced to internalize this cost. Various financial assurance schemes have been proposed to ensure that the entities fulfill their financial responsibility to restore the environmental dam-age. Prominent among these schemes are ?environmental bonding requirements?. A main issue with these financial assurance schemes is that many times the amount and duration of environmental damage is uncertain. That is, the cost of restoring the environment in the future may be unknown (or unknowable), and, furthermore, the extent of the damage may not be known for many years into the future. Nevertheless, bonding requirements have to be set in advance and the rules for returning the bond and absolving the entity of responsibility have to be specified ex ante. In practice, a problem of allocation of resources arises. To make sure that all external costs are internalized, in the face of uncertainty, will require a sufficiently (arbitrarily) large bond for a sufficiently (arbitrarily) long period of time. But such a requirement may prove too expensive and may result in not undertaking a project (even if, under certainty, the project may be profitable after internalizing all costs). This will result in a reduction in total welfare. Under present bonding requirements, firms are responsible up to the value of the bond. This results in an asymmetry: if environmental restoration is less than the bond amount, the firm has an incentive to restore and reclaim the bond; if the cost of the environmental restoration is above the value of the bond, the incentive is to forfeit the bond, imposing on the government/ society the excess cost. This also may reduce social welfare, at least on distributional grounds since the firm owners pocket the profits and the taxpayers foot the bill. The presence of uncertainty suggests that a fee based reclamation fund may be welfare enhancing. The thinking can be sketched as follows: All firms undertaking environmentally sensitive projects pay into the proposed fund. The fund examines the risks and sets the premiums at the level of the expected restoration costs (not the maximum!) plus administrative expenses. One advantage of the scheme is that this eliminates the asymmetry. Firms with restoration costs below expected end up subsidizing firms whose restoration costs were underestimated. In other words, the industry ends up internalizing the costs not internalized by the individual firms, instead of the taxpayers.

Jan 1, 2007

By T. Simpson

European industrial policy seeks to provide the right framework conditions to allow companies to develop and innovate and to make the EU an attractive place for job creation. This includes providing the basis for a competitive manufacturing industry which provides around 20% of EU economic output and employment for about 34 million people. The EU non-energy extractive industry with an annual turnover of around ?40 billion and a direct workforce of about 270,000 people is considerably smaller, but it plays a vital role in providing much of the manufacturing sector with raw materials. It also supplies very large quantities of minerals such as aggregates and natural stone to the construction industry, facilitating the development of modern infrastructure such as roads, railways, houses, schools and hospitals. However, despite an active extractive industry, Europe is increasingly dependent on imports of raw materials and particularly metallic ores and concentrates. In 2005, the trade deficit for minerals was in excess of ?11 billion, of which ?10 billion related to metallic minerals. Such import dependency is not a new phenomenon, but the rapid industrialisation of developing countries such as China and India has significantly increased global demand, resulting in large price increases for downstream industries and at times, bottlenecks in supply. The impact of this and other competitive pressures on some sectors of the European manufacturing industry, including the possibility of them being lost to lower cost countries outside Europe, has moved the issue of industrial policy and access to raw materials up the political agenda. A number of measures have already been announced by the European Commission to address these issues including: - The analysis of the competitiveness of individual industrial sectors, in order to understand their specific needs and take account of the particular opportunities and challenges they face.

Jan 1, 2006

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner(SPL) is obtained at the end of the pot's life. The SPL contains small amounts of cyanide and fluoride, which present environmental problems. Spent potliner could possibly be used as a fluidizer to replace calcium fluoride (CaF2) in the iron- and steelmaking industry and in the glass industry. A low viscosity and a low melting point are prime requirements for such an application. In the present study, viscosity measurements were performed. The effects of various additives, such as sand, limestone, dicalcium silicate dust and MgO baghouse dust, on the viscosity of SPL were studied. The results showed that the addition of sand and limestone can produce a very high fluidity SPL melt at significantly lower temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 2002

By Qiong Wu, Qinghua Gu, Yichuan Lv, Jin Yuan, Caiwu Lu

"The cut-off grade is one of the important parameters of mining production. Different material cut-off grade is directed to different destinations. Based on reasonable and optimal cut-off grade, long term mining plan and investment decision analysis can be made for mining managers. In view of multiple-metals open-pit, the paper has proposed that multiple-metals cut-off grade optimization model is set using the objective function to maximize net present value (NPV). The method of equivalent coefficient calculation is proposed to convert multi-metals cut-off grade optimization to a single metal cut-off grade optimization. Then the optimization model is applied in a molybdenum and tungsten large open-pit mine in china. The parameters of concentrate price are calculated by PRT in the model and the curve of grade-recovery rate is analyzed and studied according to actual production data. Based on 3D metal deposit model, the distribution of grade-tonnage is analyzed. At final step, an optimal cut-off grade is proposed to guarantee to maximize NPV. The example shows that the model of multiple-metals cut-off grade optimization can provide reasonable analysis for optimal multi-metals cut-off grade and develop optimal production strategies. Introduction Cut-off grade is one of the most important parameters in metal ore mining because of its influence on the overall economic profit of mining production. Along with the development of the mining production, dynamic optimization of cut-off grade is necessary through the analysis of technical economy. It is better to manage the mining production according to the variation of market. The cut-off grade plays an important role in mining production."

Jan 1, 2017

By R. F. Hüttl

World-wide Germany is the leading lignite mining nation. Most of the lignite is produced in opencast operations. However, opencast mining causes enormous impacts on natural ecosystems and even on entire landscapes. The extensive production of lignite particularly in eastern Germany results in large devastated areas, which so far have been reclaimed only to some part. For the restoration of the post-mining area of more than 80,000 ha the major land use option is the reestablishment of forest ecosystems. However, adverse site conditions of the post-mining landscape such as extreme soil acidification and salt concentrations call for specific recultivation practices. Therefore, after the German reunification new reclamation and reforestation concepts have been developed for these brown coal areas of eastern Germany by the Collaborative Research Center (SFB 565) at the Brandenburg University of Technology at Cottbus (Germany). As a case study our comprehensive investigations into forest ecosystem development on terra nova in the Lusatian lignite mining district, south-east of Berlin, will be presented.

Jan 1, 2003

By Vernon R. Degner

The past two decades has seen the application of the mechanical flotation machine, originally developed primarily for metal1iferous ore beneficiation, increasingly applied to cleaning coal in the 28x0 T. Mesh size range. Internal cell hydrodynamic studies of mechanical flotation machines of all sizes, as well as computer aided modeling studies of flotation kinetics has, within the last five years, established a basis for optimizing coal flotation circuit design and machine operation, and has a1 so pointed a way toward improvements in mechanical flotation machine design for the future. Consideration of the trend toward increased fines produced by current mining techniques, as well as the environmental need for a progressively cleaner product, lends support to basing the design of the mechanical coal flotation machine of the future on finer feed; below 100 microns in size. Future types of mechanical flotation machines, which may satisfy the fine coal cleaning requirements for a significant improvement in product grade while maintaining the combustible recovery levels of current technology, are discussed.

Jan 1, 1988

By J. A. Frew, G. I. Orrock, R. M. Glen

The zinc flotation circuit was sampled to provide sized information on its metallurgical performance. A good balance was obtained and the roughing, scavenging, cleaning and regrind sections were assessed. Substantial losses of sphalerite occurred in all sizes. The limitations were poor recovery in the cleaning section which resulted in substantial recycling of 15-30µm sphalerite and iron sulphides, and inability to float +38µm sphalerite in the roughers. Regrinding increased sphalerite recovery by 7% with no loss in grade. Liberation measurements enabled balances for six size fractions to be calculated and the role of liberation on the metallurgical performance was assessed.

Jan 1, 1993