Search Documents

By Kyeong Woo Chung, Rina Kim, Ho‑Seok Jeon, Yeongjin Ahn, Byunghun Go, Min‑seuk Kim, Hong‑In Kim, Sujeong Lee, Yuik Eom

The study focused on the recovery of vanadium from a Korean vanadium-bearing titaniferous magnetite (VTM) ore, examining the behaviors of magnetic separation and Na2CO3 roasting-water leaching. Two concentrates were prepared using single-stage dry magnetic separation and three-step wet magnetic separation, resulting in V2O5 grades of 0.8% and 1.0% and major gangue mineral SiO2 contents of 6.5% and 1.7%, respectively. These concentrates were subsequently roasted at 1050 °C with the addition of Na2CO3 and then water-leached at 25 °C. Various stoichiometric ratios of V2O5 to Na2CO3 were tested, ranging from 1:1 to 1:40 of the theoretically required amount. As the amount of Na2CO3 increased, the vanadium leaching efficiency showed fluctuations between 4 and 35% for ratios of 1:1 to 1:10, while it linearly increased from 4 to 82% for ratios of 1:10 to 1:40 in the leaching of the low-grade concentrate. In contrast, the leaching efficiency increased from 47 to 74% for ratios of 1:1 to 1:8 and then sharply rose to 84% at a ratio of 1:10 in the leaching of the high-grade concentrate. Subsequently, it reached a plateau of 92 to 94% for ratios of 1:20 to 1:40. The difference in leaching efficiency was primarily due to the reaction of gangue minerals with Na2CO3, which hindered vanadium leaching from the VTM concentrates. This hindrance was notably more pronounced in the low-grade concentrate with the lower salt ratio, as the gangue minerals exhibited a preference for consuming Na2CO3 over vanadium. The mineral formation was analyzed in detail using XRD and MLA to shed light on the mechanism of different vanadium leaching behavior depending on the concentrate grade and vanadium to salt ratio. Based on the results of this study, it is evident that applying a proper magnetic separation procedure is significant to achieving satisfactory vanadium recovery with less salt amount by removing gangue minerals ahead.

Mar 15, 2024

Over the past seven years a large database of coal self-heating rates under adiabatic conditions has been developed at The University of Queensland. Coals have been tested from Australia (Queensland and New South Wales), New Zealand (North and South Island), Indonesia and more recently the United States. As a result of this work, definitive relationships and trends have been established for the effects of various intrinsic coal properties on self-heating rates and anomalous coals have also been identified. Previously held views on the effects of coal rank, type and inorganic constituents are examined in this paper. Many of the published relationships do not hold true in terms of coal self-heating rates. A propensity rating scheme has also been developed which is routinely used in Australia for assessing coals and identifying appropriate mining analogues for spontaneous combustion management planning. A selection of examples will be presented in the paper, which shows the significance of this assessment strategy.

Jan 1, 2009

By P. M. Keyser

Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9 m (9.5 ft) diameter columns are used for rougher flotation of carbon from a gold ore (Orlich et al, 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al, 1991). With the mounting evidence, columns can succeed in any flotation application. The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include: ? Lower Capital Costs ? Reduced Operating Costs ? Fewer Processing Stages ? Improved Metallurgical Performance

Jan 1, 1993

By Werner Wenzel

Whisker growth during the reduction of iron ores The phenomenon of whisker growth can be observed in a number of solid-state crystallisation reactions, which, apparently, appear in6 the first instance as though they are two independent processes. From such reactions, one can find the whisker type of crystallisation on solid bodies. These examples show, that the whisker growth is neither due to certain crystal forms with predetermined temperature and pressureranges, nor to parameters, which, ad hoc, are necessary for the crystallisation. In all cases the whisker formation seems to depend on nucleation and the availability of crystallizing material in direct environment of such a nucleus, under given parameters of a system. One can generally state, that the research of whisker growth with the aim of establishing proper physical laws, to determine the foundamentals of whisker formation and whisker growth, is at present under active study. We can conclude that, although a great number of hypothesis have been proposed; no concluding theory has yet been arrived at. In the institute for ferrous metallurgy of the technical university of Aachen, research works are undertaken to find an explination to various metallurgical phenomena through help of whisker growth which was observed under varying conditions of iron ore reduction. This was possible by using refined microscopic techniques through which the whisker growth on solid oxyde substrates is detected. This refined technique combines the latest methods of surface examination with the help of stereo-scan-electron-microscope and proper and carefull preparation of surface to be stereo-scanned.

Jan 1, 1971

By George W. Leney

The iron ore industry might justifiably claim to have originated the science of geophysical prospecting. Their use of geophysical methods was probably the first application of these scientific techniques to the search for economic materials although the exact origin is undoubtedly lost in the unrecorded observations of. some prospector experimenting with compasses or bits of lodestone. Since 1879 when Thalen published "On the Examination of Iron Ore Deposits by Magnetic Measurements" these methods have been a standard supplement to other prospecting techniques. However, many of the great ore bodies of the Precambrian iron ranges were not particularly suitable for geophysical work. The ores were oxidized and enriched through leaching of silica so that they were nearly non-magnetic and other physical properties which distinguished them from the wall rocks were largely destroyed. With the gradual exhaustion of these high grade direct shipping ores, and ores that could be beneficiated by simple means, the iron ore industry turned initially toward the importation of similar high grade foreign ores. At the same time, new processes for concentrating lower grade materials were being developed and older ones improved upon. These concentrates' when pelletized produced such important savings in blast furnace hot metal costs that they now command a premium in the iron ore market and have weakened the competitive position of the remaining high grade ores. The ore bodies now being sought are usually unoxidized and frequently they are also metamorphosed.

Jan 1, 1965

By H. J. Ilgner

Previous applications for using waste rock for backfilling in South African gold mines were reviewed and it was found that in many cases the mechanical equipment selected and the design philosophy applied did not meet the requirements. A more simplified system configuration is proposed, which allows the equipment to be relocated as mining progresses. Innovative high-intensity grinding and dense-phase pumping technology are proposed to provide a low-porosity backfill with a particle top size of 5 mm to 8 mm. According to recent rock mechanics modeling work, this comminuted waste backfill material can provide a good compromise between underground support characteristics and reliable hydraulic transportation behavior.

Jan 1, 2001

By J. Hanna, J. Jung, I. J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous contents and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge (obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, AL and FMC Corporation in Pocatello, ID) were investigated using physical separation techniques to recover the elemental phosphorous and to render the residual material nonhazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69% - 90%P4, with recovery in the range of 60% - 87%. Dispersed air oxidation of the fines and tailings products was effective in the removal of an additional 10% - 15% of the P4 in the sludge.

Jan 1, 1993

By R. A. Limons

Natural ores, sinters, and pellets were subjected to a carbon monoxide reduction-disintegration test under laboratory conditions including a simulated blast furnace gas and a 1000°F temperature. The most significant findings were that: 1. Self-fluxed pellets broke down to a greater extent than either the acid pellets or the acid or self -fluxed sinter. 2. When pre-reduced, both the acid and self-fluxed pellets had very good resistance to breakdown.

Jan 1, 1964

By D. Sinha

Mine investment decisions involve both objective and subjective criteria. The subjective criteria are efficiently decided by interaction with company experts. The Expert System approach can incorporate knowledge of experts and interact with conventional computer programs on mine evaluation. Artificial intelligence offers considerable opportunities in comprehensive mine investment decision making process.

Jan 1, 1998

By BARBOSA AMILTON, Denise C. R. Espinosa, David B. Dreisinger

Chelating resins can be used to recover important metals from different sources, and it is important to understand which resin is most suitable for each metal [1]. This review  benefits the mining industry because chelating resins can be used to recover metals from low-grade ores and mining tailings, increasing the industrial process efficiency [2–4]. Furthermore, the use of chelating resins in mining processes and mining tailings has the common problem of metals contamination, with iron being the main contaminant in low-grade ores and tailings. Understanding how contaminants decrease ion exchange efficiency is significant for industries [5

By R. Michael

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of underground coal-mining equipment, an example of which is a roof bolting machine. Field studies show that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and it contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel and chuck radiate a significant amount of noise during drilling. NIOSH and the Corry Rubber Corporation have developed a bit isolator that breaks the steel-to-steel link between the drill bit and drill steel and a chuck isolator that breaks the mechanical connection between the drill steel and the chuck. This effectively reduces the noise radiated by the drill steel and chuck and reduces the noise exposure of the roof bolter operator. The paper documents the evolution of the bit isolator and chuck isolator. Laboratory testing confirms that production bit and chuck isolators reduce the A-weighted sound level generated during drilling by 3.7 to 6.6 dB

Jan 1, 2010

Atlas Copco Wagner launched its ST1010 Scooptram load haul dumper. The ST1010 replaces the company’s Wagner ST-1000 Scooptram. The improvements to the Wagner ST1010 include increased reliability, ease of maintenance and driver comfort or ergonomics. The ST1010 has been redesigned and has added several new features and options not offered in the earlier model. These include anew boom design with side stops. Heavy reinforcements to the bogie offer better protection against the harsh working conditions in underground mining and tunneling. An auto lube system has also been added as has paint-on grip tread to reduce slips and falls during maintenance checks or repair work. Other features include a heavy-duty, auxiliary-fan motor, an isolated transverter, remote diagnostic pressure taps, a bolt-on battery box, raised air-intake, improved fuel-filter access for easier maintenance, larger wear-bars around the engine tub, and smaller, higher output batteries

Jan 1, 2000

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By J. J. Peshel

As per the current conceptual design presented by the Department of Energy, the exploratory shaft facility (ESF) becomes a part of the repository if the Yucca Mountain site is found suitable for repository development. Therefore, the design of the ESF should be compatible with the performance requirements for the repository. The construction methods selected should limit to the extent practical, the degree and the extent of damage to the surrounding rock mass. The ESF construction and operation should be compatible with the site data gathering activities, such as geological, thermomechanical, hydrological and geochemical testing.

Jan 1, 1991

By Dr. Ing. Hermann Boldt

The Bituminous Coal Mining Industry of the Federal Republic of Germany produces nearly 100 million t/yr of clean coal. The largest coal mining area is the Ruhr District with dimensions of 100 x 40 km (65 x 25 miles). Figure 1: Here is the general administration of Ruhrkohle Akteingesellschaft RAG with its three divisions. Other coal mining areas in Germany are the Saar District and the Aachen District. Ruhrkohle produces 70 million t/yr of clean coal. The company operates 28 mines in the Ruhr District with an average raw coal production of 18000 t/day. Their average mining depth is 831 m (2740 ft.) and the average seam thickness is 177 cm (70 in.). Figure 2: Preparation plant reject is 44.6%. All following production figures will be with reference to raw coal because the raw coal production is the technically relevant number. Mining operations are mainly in non-dipping coal deposits whereby mechanized equipment for flat seams is also applied to deposits dipping up to 45? Coal extraction is done exclusively by the longwall method. Approximately 200 longwall installations are in production at any time. The average longwall length is 221 m (730 ft) ranging between 140 and 290 m (460 ft and 960 ft). The average longwall advance of all operations is 2.8 m/day (8.4 ft per day). Average production

Jan 1, 1977

By Andrew P. Gize

The analytical approaches used to solve a specific problem are dependent upon the information required, coupled with limitations imposed by available facilities, costs, and time. The organic matter associated with ore deposits has the potential to yield information for two problems. Information can be obtained to provide guidelines for prospecting, and, secondly, to solve genetic problems. A major potential of organic matter in providing prospecting guides lies in the high thermal sensitivity of organic matter in sediments which are metamorphosed at grades lower than greenschist facies. The organic matter can then be used to map thermal anomalies potentially associated with mineralization. The analytical approach is to determine the thermal maturity of the total organic matter, or of specific fractions, using techniques which are relatively quick and inexpensive. Consideration of genetic models (for example, reduction, complexing, involvement of oil field brines) generally requires more specific information than the overall thermal maturity of the organic matter, necessitating infor¬mation on molecular composition and structure. The facilities, time, and cost of this information are greater than for mapping thermal anomalies. The analytical techniques discussed include elemental analyses, spectroscopy (infra-red, visible and ultra-violet), Fourier Transform infra-red, nuclear magnetic resonance, extraction, pyrolysis techniques, chromatography and mass spectrometry.

Jan 1, 2013

By K. Marutiram, T. Umadevi, R. Sah, K. Abhishek

Low-grade iron ore received from the West Singhbhum area of Jharkhand state in India was used to develop a beneficiation flow sheet to remove alumina (Al2O3) and silica (SiO2 ) from the ore to get iron (Fe)-rich product for steel plants. Mineral characterization showed that the main mineral constituents present in the head sample are goethite, limonite, hematite, quartz, clay and gibbsite. The head sample contained about 49.2 percent Fe, 8.79 percent alumina and 12.01 percent silica. The received iron ore sample is amenable to upgradation through beneficiation to get pellet grade concentrate. The beneficiation process was established, involving crushing, screening, jigging, spiral separation, size reduction, desliming and magnetic separation. The process showed significant enrichment in Fe values to 63.5 percent Fe in concentrate, from 49.2 percent Fe. From the developed flow sheet, it is possible to obtain pellet grade fines with 63.5 percent Fe, 2.92 percent SiO2 and 2.61 percent Al2O3 with 50.6 percent weight recovery. The overall tailing loss is 49.4 percent with 34.3 percent Fe, 21.28 percent SiO2 and 14.64 percent Al2O3

By K. F. Unrug

The concept of bolting mine roofs to prevent roof falls was initiated in the 1950's and was quickly accepted by the mining industry because it was inexpensive, effective and convenient. The principle regarding roof bolting were that: a) the loose and fragmented rocks were suspended from or clamped to more competent surrounding rock and b) generally, by clamping several layers of thin and laminated strata, a more competent monolithic beam is created.

Jan 1, 1991

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978