Search Documents

By T. E. Mccandless

Detrital minerals of mantle origin have been found in the Green River Basin of Southwestern Wyoming (Figure 1). Pyrope, pyrope-almandine, and chrome-bearing clinopyroxene and orthopyroxene occur on the antmounds of Pogonomyrmex Occidentalis. These antmounds are a common sight throughout the western U.S., and were used by early paleontologists as fossil mammal collection sites. The mound is composed of two types of material; (1) soil excavated during the digging of the nest below the surface (maximum depth 3 meters) and (2) larger grains collected from the surface and placed on the mound, probably to prevent erosion. The selection of grains to armor the mound seems to be based largely on the mean diameter of the grain, with other factors such as weight, sphericity, roundness and composition in decreasing order of importance (Wheeler and Wheeler, 1963). The minerals of this study happen to fall within that mean diameter range. The garnets are found on the mounds as 3-6 mm diameter subrounded to subangular grains. The pyroxenes are also 3-6 mm in diameter and are most commonly subangular laths. The minerals themselves show evidence of abrasion, such as frosted surfaces and rounded edges. Orange peel texture is present on some of the grains, which suggests that kelyphitic rims were once present, but have been removed. Also, no similar minerals were found in sieved soil auger samples to depths of 2 to 6 meters taken near the antmounds. These observations imply a distal rather than proximal source for the minerals. Lamproitic rocks of upper mantle origin are found bordering the "Green River Basin. The best known are the Leucite Hills, a series of ultrapotassic volcanics found on the north flank of the Rock Springs Uplift (Carmichael, 1967). Minor occurrences of mica peridotite and ultrapotassic volcanics are also found on the western end of the Uinta Mountains in Utah (Best, et al, 1968). None of these rocks are known to contain minerals like those on the antmounds. The garnets are comprised of purple chrome pyrope, red chrome pyrope-almandine, and pink to orange low chrome pyrope/pyrope-almandine. Oxide statistics for these groups are summarized in Table 1. These three groups are distinct when their Cr203 values are plotted against magnesium number (Figure 2). The chrome pyropes are highest in Cr203 (1.28-2.66%) and have high, restricted Mg number values (0.781-0.826). The chrome pyrope almandines have similarly high Cr203 (1.29-2.62%) but a lower Mg number range. The low chrome pyrope/pyrope-almandines have the lowest Cr203 content (0.09-0.73) and the widest Mg number range (0.534-0.836). Using the classification scheme of Dawson and Stephens (1975) the chrome pyropes are most similar to garnets derived from kimberlite and from garnet lherzolite, websterite, and harzburgite xenoliths in kimberlite. The chrome pyrope-almandines and the low chrome pyrope/ pyrope almandines are similar to garnets derived from eclogite nodules (Figure 3).

Jan 1, 1984

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), we showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/t of REEs occur in AMD and AMDp, respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. 

By V. N. Kolesnikov

The gold-silver deposits of the northern Primorye region are located in the eastern part of the East Sikhote-Alin volcanic belt, where the belt overlaps the Kema island-arc terrain of the Aptian-Albian age. There have been four deposits and numerous mineralization points found in the NE-trending Kema metallogenic belt that is about 1000 km long and 100 km wide. The known mineralization is of epithermal type, controlled by faults, and concentrated in quartz, quartz-fluorite-adularia, and, less commonly, sulfide-quartz vein systems hosted by the Upper Cretaceous-Lower Tertiary volcanic rocks. The vein systems extend for hundreds meters along strike, varying from tens centimeters to 50-60 meters in width. They are surrounded by wide zones of low-temperature hydrothermal alteration containing some gold-silver mineralization for which the commercial value was not studied during the early exploration. The ore bodies contain from 1 to 50-80 ppm of Au and from 1 to 1000 ppm of Ag. Gold is native, associated with quartz, and represented by particles from tens of microns to 1 mm in size. Silver occurs in native form as a constituent of argentite, pyrargyrite, stephanite, and other sulfosalts. The test work carried out for three vein systems 20 years ago showed that gold might be easily and almost completely recovered from the ore by cyanide treatment. The paper describes the geology and mineralogy of the deposits, Salut and Primorskoye, that are the most studied properties of the Kema belt. It also presents the data available on disseminated gold-silver mineralization in stockworks, altered explosive breccias, and wide zones of low-temperature hydrothermal alteration. This mineralization should be explored for possible exploitation as large open-pit, heap-leach deposits.

Jan 1, 1998

By A. Noble

"A supply of sustainably sourced rare earth elements (REEs) is critical for several high-tech industries, renewable energy technologies, and defense applications. Recent studies have shown that REEs exist in coal and coal combustion byproducts at elevated concentrations and in quantities that could meet domestic demand. Despite these promising findings, declines in rare earth prices, volatile commodity markets, and challenging geo-metallurgical conditions have jeopardized this potentially valuable REE resource. While the dilute REE concentrations inherently necessitate low-cost separation technologies, the ultimately operating cost threshold for economic extraction must be based on commodity price projections and market demand. In this paper, the micro-pricing principle is used to develop a rigorous economic model assessing the inherent value of REEs in coal materials. This model is based upon basket pricing of individual elemental oxides, and elemental distributions of coal samples from various basins. These results may be used to assess the economic viability of potential REE concentration and refining technologies INTRODUCTION Recent efforts by US Department of Energy (DOE) and the National Energy Technology Laboratory (NETL) have suggested that rare earth elements (REEs) may exist in coal and coal byproducts at concentrations suitable for economic extraction and processing. While the knowledge of REE occurrence in coal material dates back over 50 years, recent supply restrictions and material criticality considerations have prompted a national interest to establish a sustainable domestic supply of REEs. REEs are not “rare” in the sense of crustal abundance; however, few natural processes lead to concentrated ore deposits. As a result, the elevated concentrations found in coal material may provide a potentially promising resource for these materials. While the term “rare earths” is often used to describe a singular concept, the 15 rare earth elements actually have varying and sometimes contrasting scarcity and cost profiles. Various authors have proposed classification systems to provide information on REE criticality (e.g. Seredin and Dai, 2012, Zhang et al., 2015). The most straightforward classification is provided on the basis of geochemistry with designations for “light”, “medium” and “heavy” rare earths. Light rare earths (those to the left of the periodic table: Ce, Pr, Nd, and Sm) tend to be more common and less valuable when compared to their medium (Eu, Gd, Tb, Dy, and Y) and heavy (Ho, Er, Tm, Yb, and Lu) counterparts. While light rare earths are often found in traditional ore deposits at economic concentrations, the heavier rare earths are almost exclusively found as ion-absorbed clays (Seredin and Dai, 2012)."

Jan 1, 2016

By C. A. Rowland

Comminution efficiency can be expressed in three different ways. Theoretical Efficiency: actual energy consumed, in a comminution machine compared to the theoretical energy required to make the size reduction. Operating Efficiency: compares the operating work index, calculated from production comminution machinery operating data, to the Bond Work Index from bench scale comminution tests or calculated from pilot plant operating data. Economic Efficiency: income compared to planned income. Using the Bond Work Index and operating work index, this paper explains how to determine operating efficiency.

Jan 1, 1998

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4 km (6.5 mi) long, 14.4 m (47.5 ft)bored tunnel that will run under the City of Niagara Falls from the Upper Niagara River to the Sir Adam Beck Power Station. The completed project will enhance the capacity of the Sir Adam Beck Power Station by adding 500 m3 (17,657 ft3) of water per second through the tunnel. The paper describes the project in which the world’s largest hard rock TBM at14.4 m (47.5 ft) in diameter is being used to excavate the tunnel. Features of the project include the use of a High Performance (HP) Main Beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area. The paper will also discuss the optimization of the TBM system as the tunnel advances through the varying geology. In June 2004 the Ontario Government announced that Ontario Power Generation(OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls—the first two tunnels were constructed in the 1950s using drill and blast techniques. The third tunnel, appropriately named The Niagara Tunnel Project (NTP), consists of a 10.4 km (6.5 mi) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG announced the selection of Strabag AG of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP Project at a price of CAN $600 million. In September 2005, Strabag A.G. selected The Robbins Company of Solon, Ohio to design, manufacture and deliver a new 14.4 m (47.5 ft) diameter High Performance state-of-the-art Main Beam Hard Rock TBM to be used in the excavation of the tunnel. In order to meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be supplied as “ready to bore” within a 12 month period after the contract was awarded to Robbins.

Jan 1, 2007

By J. Noll

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks, or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (Minimum Efficiency Reporting Value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50 percent of the DPM, a MERV 16 filter collected 96-98 percent of the DPM, and two HEPA (high efficiency particulate air) grade filters captured over 99 percent of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90 percent effective in removing DPM except under certain operating conditions when the efficiency was as low as 41 percent. Evidence seems to suggest that these conditions were when a window was open in the cab.

Jan 1, 2011

By Raymond Sandiford, Taehyun Moon

"In 2012, Superstorm Sandy (Sandy) caused extensive flooding in many of the tunnels in New York City. The inundation resulted in two distinct stress changes to the tunnel structures. The first stress change was water pressure on the inside face of the tunnel lining. The second condition related to the change in buoyancy of the tunnels. In areas where the tunnels were supported on rock and an adjoining area supported on soft soil, overstress issues arose. Numerical analyses were performed to assess the structural impacts of the tunnel water inundation; especially stress changes due to internal pressure as well as changes resulting from the buoyancy effects. The paper will discuss the assessment process and its results; it will demonstrate that the change in internal pressure were of little consequence, however the change in buoyancy resulted in significant increases in bolt stresses. INTRODUCTION Superstorm Sandy caused tens of billions of dollars in damage in the NYC metropolitan area. It also caused significant disruption to the transportation system by flooding most of the under river tunnels servicing Manhattan from the outer boroughs and New Jersey. The rehabilitation of the tunnels was of paramount importance to the restoration of the NY and NJ economies. With this rapid restoration, it was essential to determine whether the flooding of these tunnels caused damage to tunnel structures. A series of analyses were undertaken to ascertain whether the change in the stress conditions and buoyancy of the tunnels, due to the flooding, was significant enough to cause damage or over-stressing of the tunnel components. The effects of this unforeseen loading condition was a concern to the agencies operating these tunnels and were thus analyzed to ascertain if there were any adverse impacts. This was a concern because the majority of under river tunnels in NYC was built earlier in the century and constructed using bolted cast-iron lining segments. The cast iron, although quite strong in compression, is much less so in tension. Also, after nearly a century of use, the bolts connecting these segments together have under gone varying degrees of corrosion. The stress changes in both the liner segments and the supporting bolts were estimated for conservative ground support conditions to provide confidence that the flooding had not caused permanent damage."

Jan 1, 2016

By Katherine Hynard, Colin Eustace

Suboptimal decisions introduced during the mine planning process are generally a consequence of both a myopic view of planning objectives as well as time and resources available to convert longer-term plans into execution plans. Erosion of strategic mine plan value in conversion to execution plans is likely to amount to billions of dollars each year. When integrated with operations data feeds, simulation and optimization tools can be used to preserve the value in the strategic mine plan. Optimization models are capable of both automating production of execution plans and improving performance. This reduces the manual burden of revising plans while improving alignment with long-term production objectives. Simulation models can also support the process of developing effective execution plans by providing forward visibility of mine operations performance. They can also be used to test the robustness of optimized execution plans and response to operational variability and disturbances.

May 1, 2025

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023

By N. Arbiter

During the first four decades of flotation practice, close to 200 machine designs were patented, although only about a score were ever used commercially. By the end of that period, the rigors of use had resulted in obsolescence of most pneumatic cells, with a few mechanical cells dominating the field. After World War II, newer designs began to appear but most were modifications in varying degrees of older designs with special features added. Of the dozen or so most recent developments, almost all are pneumatic, relying on compressed air instead of impellers for motive power, although in several cases pumps supplement compressors. Table 1 lists a few of the more fully documented new cells, with their significant characteristics, along with similar characteristics of a widely used mechanical cell. New designs in general are emphasizing: bubble size control; in several cases, methods for delivering feed directly to the froth; methods for introducing and dispersing air through nozzles, eductors, packed beds, or permeable walls; and variable cell volumes, relative to capacities, ranging from very small, with less than a second of retention time, to the largest, with retention times of over 20 min. An important question is the extent to which any of the newer designs are based on locating weaknesses in current mechanical cell designs and then using these as a starting point for innovations. In the present study, the key subprocesses which must take place in a cell are outlined; mechanical cells are analyzed to establish where weaknesses may exist; and then alternative subprocesses are considered which could effect improvements. COMPONENTS FOR CELL DESIGN It is assumed that mineral surface chemistry has been modified as necessary to provide optimum potential floatability. While the cell process may affect this to a degree, cell design is primarily concerned with actualizing the existing potential floatability. The cell design problem is to provide more effectively for the following: 1) Dispersion of air to obtain an optimum bubble size distribution at an optimum ratio of air volume to feed volume. 2) A hydraulic environment which permits most effective contact of potentially floatable particles with bubbles: [Table I - Cell Comparisons* Cell Type Mechanical Column Deister Miller ASH No. of units Multiple Single Single Single Retention time min.10/20 17/27 3.8 ca. is Capacities mt/m3s 0.022/0.066 0.066/0.20 0.11 10.4 st/ft3d 1/3 0.3//0.9 m5.0 469 Air hold-up % 15/20 20 n.a. 50/80 Air escape velocity m/s 0.015/0.0200.020/0.025 n.a. n.a. ft/m 3/4 4/5 n.a. n.a. * References: Mechanical (Harris, 1976,1985), (Bassarear, 1985); Column (Travis, et al. 1987); Deister (Zipperian and Christophersen, 1985); ASH (Air-Sparged Hydrocyclone) (Miller 1989).]

Jan 1, 1989

By Amy McBrayer, Andrea Brickey

Limited research has been conducted related to the development of mathematical optimization models for production scheduling at large surface coal mines using the area, i.e., strip, mining method. Increased economic and technical challenges have led to a new interest in production schedule optimization models for these type of mining operations like those currently applied to model underground and open pit mines. While area mines share similar characteristics to both open pit and underground metal operations, neither an open pit nor underground production scheduling model adequately depicts an area mine mathematically. We present an integer programming model with blending constraints and discuss the challenges and opportunities related to the implementation for area mines as well as future research in area mine production scheduling.

Jun 25, 2023

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By J. Kretschmann

Mining heritage can be of outstanding value for many regions around the world, because mining has been done for thousands of years for the benefit of mankind and its development. This paper presents an ongoing project creating a general guideline for the handling of mining heritage on the basis of experiences made in Germany. Interactions of stakeholders in the ?heritage network? as well as strategies for the technical proceeding will be described. An action plan for the sustainable handling of mining heritage has already been developed in part, which includes necessary measures. Best-practice recommendations will be derived. Keywords: m ining heritage / preservation / guidelines / action plan / Sustainability

Feb 27, 2013

By Ma. X.

Passive seismic imaging is applied in underground mining to analyze the stress redistribution after the occurrence of a major seismic event. The velocity model is established to be utilized in velocity inversion. By comparing the images from velocity tomography on two different time scales, the average velocity of a mining area decreases significantly after the major event. It is highly likely that the stored energy level drops due to the occurrence of a major event. Also, total energy stored in micro-seismic events for each day is summed up and the energy change trend is plotted to illustrate the correlation of energy with a major event.

Feb 27, 2013

Researchers at National Institute for Occupational Safety and Health (NIOSH) are investigating how fiber-reinforced shotcrete mix designs can be extrapolated from proven designs employing wire mesh. This paper explains the results of round determinate panel tests and relates the flexural strength and toughness of fiber-reinforced shotcrete to known energy absorbing properties of wire mesh. The energy absorbed with central deflection is strongly influenced by the amount of fibres. The higher the energy absorption the more load cracked shotcrete can support. Two types of fiber-reinforced shotcrete were investigated, one with steel fiber and another with polyfiber. The residual load supported in Round Determinate Panel Tests can be matched with the strength of wire mesh, thus providing equivalent bag strength values for fiber reinforced shotcrete panels. There is also evidence of a panel crack width comparison to the load holding capabilities of the fiber in the shotcrete mixes. In practice, this provides designers with a method for comparing the ground support provided by fiber-reinforced shotcrete with that supplied by wire mesh.

Jan 1, 2010

Impala Platinum?s No.16 Shaft mine is currently under construction and is expected to reach full production of 256 500 tons per month by 2014. Mining will start at 1 260 m below surface with a maximum mining depth of 1 535 m where virgin rock temperatures of 56.6°C will be experienced. As a result of depth, high virgin rock temperature and narrow reef mining, an expected total of 31.5 MW[R] of air cooling capacity will be required to achieve acceptable underground conditions. This will be achieved by cooling mine intake air in a single dedicated air cooling installation located on surface. The compact installation includes air cooling spray chamber, refrigeration machines, condenser cooling towers, evaporator and condenser water reticulation as well as all electrical and control systems. Construction and commissioning of the first phase of this air cooling installation has recently been completed on a turn-key contract basis.

Jan 1, 2009

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By G. Jalkanen

Dealing with a trend in inverse distance estimation, IWD, is presented. A measurement is proposed to be consisted of a portion due to a mean and a portion due to a residual. The procedure consists of de-trending the measurement via a linear or nonlinear regression. Residuals are computed, and IWD parameter estimation is conducted on the residuals. Estimation at un-sampled points is then computed by estimating the mean and adding on the estimate of the IWD on the residual. A possible BOXCOX transform is also proposed.

Jan 1, 2010