Search Documents

By Robert A. Cummings, Madan M. Singh

In April 1984 a subsidence depression formed directly beneath a two-story frame residence, near Linton, IN, causing 2 ft of separation between the floor and walls, and damaging both the foundation and interior of the building. The Office of Surface Mining undertook the rehabilitation of the area under its emergency response program. This paper describes the investigation performed to determine the cause, severity, and extent of the problem. Abandoned mine workings were found approximately 55 to 60 ft below the house. Based on the findings, remedial measures were prescribed. An abatement program consisting of grouting the mine voids was recommended, and specifications prepared. These were implemented, and the area has been successfully stabilized.

Jan 1, 1986

By O. Guyot, T. Mulpeter

Sadiola Hill mine is located in the sub-Saharan part of Mali. In its first two years of operations, Sadiola Hill mine had already exceeded expectations with respect to profitability, plant capacity, metallurgical recovery, cash costs and social integration into the area. The advanced control system installed by the authors has been a major contributor in the substantial throughput of the mill over the design tonnage with no loss of recovery. The run-of-mine ore at Sadiola consists of soft clays with a varying percentage of grit, producing a high viscosity slurry. The percentage of grit fed to the plant varies on an hourly basis. This combination was expected to have a large impact on the milling circuit and determined that the early installation of an expert mill control system would be advantageous. Svedala Cisa OCS©, was selected as the most suitable support software. The operational rules and control philosophy are housed in the OCS© graphic-oriented fuzzy expert system while a model­based Soft Sensor has the remarkable ability to detect the variations in grit in the feed. Designed during the second half of 1996, commissioning of the system began in March 1997, the OCS was fully on-line by September. With the implementation of the optimising control strategy a throughput of 5.0 million tons relative to the target of 4.4 million tons was achieved for the 1998-operating year. The Sadiola project confirms that advanced process control techniques are among the most cost-and time-effective methods of improving metallurgical plant performance. The recipe that worked at Sadiola is a mix of metallurgical expertise, proper software selection, adequate design of control philosophy, and excellent plant support and follow­up. The early decision, design and installation of the mill control system has resulted in an enhanced Return on Investment.

Jan 1, 2000

By Ch. R. V. S. Nagesh, Ramesh Naidu Mandapati, Venkata Swamy Nalajala, Tondepu Subbaiah, Naga Jyothi Kothamasu

Leaching studies of magnesite obtained from Tamilnadu Magnesite Limited, Salem, have been carried out using hydrochloric acid leaching and percentage of magnesium chloride recovered was estimated. The variables considered in this study were the following: duration of leaching, volume percentage of hydrochloric acid, temperature, and pulp density. Percentage recovery of magnesium chloride increased with duration of the leaching, volume % of concentrated hydrochloric acid, and temperature. Percentage recovery of magnesium chloride decreased with increase of pulp density. The optimum conditions found to be pulp density (10%), hydrochloric acid concentration (30%), duration of leaching (2 h), and temperature (348.15 K). Iron was removed by treating the leach liquor with hydrogen peroxide and by raising the pH to 3.5–4. The purified leach liquor was subjected to spray drying for producing high pure magnesium chloride.

Jun 7, 2022

By John C. Harkey

The paper shares programs that presently use the CDC PLATO System to train individuals in industry. A short history of PLATO development; as a training system is presented with reflection on the major training trends being used to improve training effectiveness. A discussion is offered to describe the benefits of using a system for individualizing instruction. An introduction; is offered showing how one can recognize' individual differences, with an explanation of how the strengths of a computer are used to deliver and manage the training. Simulations of hazardous processes are shown to be one of the most effective uses of the computer for training.

Jan 1, 1979

By Björn Johansson

"SUMMARY Every tunnel designer has to consider the power of water ingress when designing a new tunnel. Either you choose solutions with simple methods to divert the ingress water or a robust system with the intention that it will give gain on low maintenance costs and a long lifetime. This article describes a new method to divert ingress water in a robust way and more economical than traditional concrete lined tunnels. This system is based on a bolt grid suspending a water tight membrane, which is reinforced and covered with sprayed concrete. The method has been in limited use in Sweden since 2005 and with continuous improvement, still going on, it is now applied for the large project “Stockholm Bypass”, a 21km long highway project. TUNNEL MAINTENANCE RELATED TO WATER INGRESS The Swedish Transport Administration maintain approximately 190 various tunnels that is constructed by a number of different methods, (Swedish Transport Adm 2015). Commonly the ground conditions are good and fairly low ground support is needed. Contrary water and winter conditions can be sever, which gives high impact onto the tunnel design and in particular methods to protect against “frost and water ingress”. During a tunnels lifetime it is common that maintenance related to water ingress occurs several times and sometimes frequent occasions every year. Such maintenance costs and consequences of lost open time for the tunnel can rapidly become higher than the initial cost of the tunnel. Thereby it is obvious that spending time during design to evaluate requirements for a suitable system against water ingress is preferred. Icicles Icicles are formed when water is below freezing degrees and drips or run from an ingress point. At very cold conditions also water flows running at high velocity freeze into ice and a rapid growth can appear. If the integrity of the tunnel traffic area is interfered by icicles they urgently have to be removed before they cause an accident. Typically the tunnel or a part of the tunnel must be closed to do such maintenance. TUNNELS FROST AND WATER INGRESS PROTECTION IN SWEDEN In Sweden methods to perform “frost and water ingress protection” are primary developed for drill and blast tunnels as it is most common tunneling method. The foundation Swedish Rock Engineering Research has done a comprehensive report SveBeFo Rapport 77 that describes water and frost prevention in Swedish tunnels up to year 2005. Below is only slight description of those various methods. Lately some more attention is paid to concrete lined tunnels made by TBM since TBMs successfully built water tight tunnels in City Tunnel (Malmö) and Hallandsås Project. When environmental demands require maintained ground water levels, water tight tunnels made by pressurized concrete lining becomes more economical and on the same time also becomes protected from icicles and water drips."

Jan 1, 2016

By Robert C. Speck

The U.S. coal industry has long utilized the pillar-extraction mining technique as a method for maximizing coal recovery. Like longwall mining, it causes large-scale movements that progressively propagate from mine-level to the ground surface and may affect the groundwater regime, surface drainage and surface structures. The U.S. Department of Energy, in an effort to foster in- creased use of total extraction mining techniques, has recognized the need for a better understanding of these movements that will lead to a greater compatibility between coal mining and present and future land use. As part of that goal, GAI Consultants, Inc. is currently in- stalling instrumentation to monitor the ground movements associated with pillar extraction mining at Kitt Energy Corporation's No. 1 mine in northern West Virginia.

Jan 1, 1982

By G. E. Bandelis

In this paper, solid bed erosion processes and the mechanisms involved when a two-phase liquid-solid mixture flows over a bed of solids in a horizontal annulus are analyzed. There are few such studies available with some authors arguing that the flow rate for erosion is always less than the flow rate for the suspension of solid particles thus necessitating further study and analysis of such phenomena. Tests were run to determine the mechanism of erosion and the erosion velocities of the solid bed formed in a concentric annulus for three flu-ids, water, a low concentration water solution of Carboxyl-methyl-cellulose (CMC), which behaved as a Newtonian fluid and a higher concentration CMC water solution which behaved as a power law fluid. Glass spheres of 2 mm nominal diameter were used as solids. The flow rate at which erosion occurred together with the mechanism of bed erosion were determined visually, while the whole process was video recorded. Our tests indicated different erosion mechanisms and different erosion velocities for the three tested liquids, with the liquid viscosity playing a major role. The first mechanism, observed for water flow, gives erosion from the front of the bed while the second mechanism, observed for the flow of the two viscous fluids, gives erosion from the top of the bed. The role of each of the parameters to erosion is investigated, whether it is turbulent flow with the turbulent fluctuations being more capable to remove the solids from the formed bed or whether it is liquid viscosity, which results in the hydrodynamic shearing force. The results demonstrate that liquid viscosity plays a role in the erosion mechanism and yields different erosion velocities of the solid bed hence, it should be taken into account when modeling flow pattern transitions for solid-liquid flows. Prior studies have not identified this and it could be the reason of the disagreement between theoretical models and experimental and field data.

Jan 1, 2006

By E. Craig Simmons

Uranium is an element incompatible with respect to the major rock-forming minerals crystallizing from granitic magma, entering in- stead trace minerals such as zircon. The relationship between the saturation limit (SL) for such a mineral and the bulk distribution coefficient (Do) for U is central to understanding the distribution of U and its availability to late- stage fluids which can form ore deposits directly, or labile U which can be remobilized later. Low SL values imply early crystallization of zircon, but in very small proportions, minimizing Do and maximizing the degree of enrichment of U in late-stage fluids. Thus, granitic rocks with low Zr contents (due to a low saturation limit for zircon) are most likely to evolve U- enriched differentiates; this will be reflected in a high U content of the zircons (but not necessarily high U abundances in whole-rocks). Thus, the ratio of the U content of zircon to the Zr content of the corresponding whole-rock is potentially a very useful parameter in identifying granitic rocks which are most likely to have U-enriched solutions associated with them. The granitic rocks associated with the U deposits of the Midnite Mine area, Washington, have geochemical characteristics which fit very well the model presented here. The rocks are very low in Zr (100 ppm) and contain zircons with extremely high U contents (3,000-4,000 ppm).

Jan 1, 1981

By Jack E. Thompson

I have spent my entire life in the mining industry pursuing what I believed was an honorable profession that provided products that were critical for our social and economic well being. Now I am told that all of my efforts been for nothing and that I have been doing something morally wrong - mining. This view of the future is not one that the mining industry has to allow to unfold. A determining factor in how things will turn out is continued improvement of the industry's environmental performance. To some extent, the current state of affairs in the United States is a result of the common perception that greedy corporations (usually foreign) are somehow ripping off US citizens of their native birthright or natural treasures in the name of corporate profits. Implicit in this view is the belief that corporations will take shortcuts or violate the environment in the name of profits. I have 26 years of experience in working in the copper, uranium and gold industries. Profits during those years were meager and difficult to find (Fig. 1). In fact, when I began working fresh out of college, I chose copper, which was then selling at around $1/lb. By the time I left copper mining, it was selling for 45 cents/lb. I then moved to uranium, which was selling for $52/lb. By the time I left it was $16/lb. I finally picked gold, which was then at ($650/oz). There is a whole generation of engineers, geologists and professionals who have spent two decades downsizing, closing mines, improving costs and getting smarter about how the mining industry does what it does. The environment, health and safety are areas where there have been great improvement. There are five characteristics of corporate governance that are critical for a company to develop and an industry to embrace if environmental, health and safety excellence is to reach new heights in the labor pool.

Jan 1, 1997

By Jerry Wang, Greg Bold, Mahmood Khwaja, Rebecca Caldon, William Simcoe

Phase III and Phase IV of the Beaver Creek Clean River Project, Albany, NY, includes microtunnel construction of 2,320 feet of 48-inch/36-inch internal diameter (ID) conveyance pipe and a 525 foot long 9.5-ft horseshoe shape roadheader excavated tunnel. Notable challenges were encountered during the construction including mixed face tunnel conditions, undocumented existing fill ground conditions that resulted in settlement during shaft construction, and unstable tunnel face conditions. This paper discusses several of the key challenges encountered during construction and selected solutions to construction sequencing and methodology to successfully complete Phase III and Phase IV of the Beaver Creek Clean River Project.

Dec 1, 2022

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature-dependent physical properties of frozen rock mass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite-element model, for the analysis of the effects of roof bolting in a frozen rock mass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rock mass: creep deformation and the change in Young's modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected and shows that, for a given set of rock-mass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1997

By B. Huang, H. Sevim, R. Honaker

The use of medium-to-high sulfur coals has been negatively impacted by the 1990 Clean Air Act Amendment (CAAA). In this article, a method is demonstrated that can render these coals competitive and yet compliant with Phase II of CAAA. The method uses strategic mining and optimized preparation plant operation to minimize production costs, and it utilizes advanced coal-cleaning technology and an SO2 allowance to produce a compliant coal. The method is illustrated through an example from southern Illinois. For an annual production of 3.2 Mt (3.5 million st) and with a $150/st SO2 allowance cost, it was possible to produce a competitive coal for $0.84/million Btu. The production and allowance costs were $0.608/million Btu and $0.232/million Btu, respectively.

Jan 1, 2002

By George M. Anderson

The extraction of industrial minerals is usually confined to relatively small mining operations. The recent COSMAR (Committee on Surface Mining and Reclamation) report found that 93% of all mines in the United States were of the small unit variety. Also, of the total number of mines in the U.S. (15,279) 96% were in the industrial minerals (non-metals excluding coal) category. To break it down further, 86% were sand and gravel, and crushed stone operations. Therefore, we are talking about a very large number of small mining operations. If these small miners can afford to hire a college graduate, what kind of training should this person have beyond the normal mining engineering curriculum to best serve the problems that he or she will encounter?

Jan 1, 1981

By H. E. Grand

The purpose of this paper is to outline briefly some basic principles of ground- water hydrology that have application in mine hydrology. The development of a mine below the water table pleads for accurate values to answers of hydrology problems. Such problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by isotropic rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where isotropic rocks are not present. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground water used by -hydrologists in the study of behavior of wells should be helpful to mine operators, The work of the Ground Water Branch of the U.S. Geological Survey through its history has been confined largely to the study of ground water as a resource, In view of the increasing number of problems relating to drainage of mines, the Branch started an investigation of mine hydrology in 1945 under the direction of W.T. Stuart, Mr. Stuart and other workers are making detailed studies of specific mine areas. In the present paper an attempt is made to synthesize some facts about ground water into usable form for the typical mine operator. Mining operations that extend below the water table disturb the natural hydrologic regimen, Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine. The behavior of the cone of depression, as it tends to deepen and increase in areal extent when the mine deepens, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised.

Jan 1, 1958

Diesel engines are used in underground mining 1 throughout the world. Exhaust gases from those engines contain toxic components. To protect quality in underground mines, diesel emission control was introduced decades ago, many years before the first surface applications. Today, emission controls, such as catalytic converters, are standard on underground diesel engines in countries concerned with occupational safety and health. Nett Technologies manufactures a range of diesel emission-control devices for underground mining. Emission problems are not the same at each mining operation. And there is no universal control technology. The selection of exhaust aftertreatment technology depends on raw exhaust emissions, particular emission problems, fuel quality and economics. Some of the technologies that have been used in underground mining to control diesel emissions include catalytic converters, diesel filters, fume diluters and water scrubbers. Table 1 compares the effectiveness of these technologies to control the particular components or aspects of diesel emissions.

Jan 1, 1997

By Jida Wu, Zhenqian Wang, Chusheng Liu, Wenqiang Qiu, Mengqi Zou, Wei Zhao

During the dry screening, the hole plugging is a serious problem for most traditional screening equipment sieving the moist fine coal. It would lead to the low preparation efficiency and the low screening efficiency. The flip-flow screen is a new kind of screening equipment by using flip-flow motion of elastic screen surfaces to implement the separation of material. With the remarkable advantages of the extraordinary vibration intensity of screen surface, the hole is difficult to be plugged, and the screening efficiency is improved. In this paper, a kind of centralized forced flip-flow screen (CFFS) was proposed based on the crank rocker mechanism. The flip-flow motion of elastic screen surfaces is achieved by the periodical reversed motion of inner and outer screen boxes driven by crank. The advantages of the CFFS include considerable deformation of the screen surface, stable flip-flow quantity, low working noise, low vibration influence on environment, etc. The principle and construction of the CFFS were introduced, and the modal analysis and harmonic response analysis of key components (the crank and the linkage) were implemented based on finite element method (FEM), respectively. The first six orders of natural frequency and vibration modes were obtained. The maximum equivalent stress and strain under working and resonance frequency were achieved. The results illustrate that the resonance frequency is much higher than the working frequency, and the stress and strain are all within the safe limit of the material. The prototype was manufactured, and the sieving experiment demonstrates that the CFFS perform steadily, and screening efficiency is over 80%. The new feasible method of the dry screening was proposed by the CFFS. The corresponding numerical simulation and the experiment provided a reliable basis for the future promotion of similar product design and research.

Jan 1, 2017

By Xiangze Shu, Yuzhong Xing

All programs used to optimize main fan nowdays have to be run on the large and medium- sized computers. With a lot of array elements, complex processes, low convergence speed and large storage, these programs are both time consuming and difficult to be used in the micro computer. This program uses two languages (dBASEIII and BASICA) to calculate the network and to choose the fan respectively. It allows user to compare and choose the parameters of various kinds of fan and to transfer the selected fan parameters to the master program by a data communication system. Then the user can get the air quantity, the air pressure, the power and the efficiency of the main fan. The advantages of this program arc as follows: 1. It can be run on IBM-PC or compatible micro computer. 2. It can select a fan more quickly and less time consumingly. 3. It can choose desired one or a set of fans according to user's requirements. 4. It is suitable for the research institutions and coal mines.

Jan 1, 1991

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.

By J. C. Purcupile

In this time of increased coal demand, a faster and safer method for roof support is needed. This report outlines the preparation and testing of a machine which we feel will help answer this need. The results of the tests are encouraging, and indicate that further exploration of the method should be continued.

Jan 1, 1975

By R. Dewey

WHAT IS AI? It's very hard to say. Most researchers and practitioners disagree with nearly any attempted definition, but most would agree that A1 does deal with the development of computer-related methods o f problem-solving. Artificial intelligence is a discipline which seeks to emulate human anatomy and/or thought processes by applying computer science, electronics, and mechanical engineering to the development of natural language processing, machine vision, robotics, and knowledge-based expert systems. Integration of these four fields will someday produce the robots of today's science fiction. A1 addresses problems of structuring large amounts of knowledge and representing relationships with rules and semantic frameworks rather than with mathematical equations. A1 is convergent rather than divergent - - conventional conputer applications use relatively small quantities of input to generate large output, but A1 generally reduces large amounts of information to establish a few major conclusions. The development of A1 has prompted greatly increased efforts on the part of scientists and engineers to understand just how humans think, organize information, approach problem-solving, and form conclusions. Some of the more exciting and possibly far-reaching advances in A1 are coming in this more-or-less soft-science area. Thirty years of A1 research (dating from a 1956 conference at Dartmouth College at which the term A1 was coined) has already spawned many widespread, almost ordinary, products: window graphics, hand-held controllers (mouse). function menus, etc., all in an attempt to make computers and people more compatible. WHAT IS AN ES? A1 can be used to develop EXPERT SYSTEMS, which are computer programs or systems which contain knowledge and rules by which problems can be solved. or at least by which possible solutions can be suggested for very complex problems. A1 can be used to better define problems so that solutions can be found. An ES is designed not to process numbers, but to process information according to rules and logic derived from actual practice and experience. WHY AI? WHY ES? Companies are increasingly aware of the value of accumulated knowledge and experience in designing, building, operating, and maintaining the increasingly complex or expensive physical plants in any business. As knowledge branches out and becomes more specialized, the accumulated learning of a veteran operator or manager or engineer becomes a scarce resource well worth preserving. EXPERT SYSTEMS offer a means of doing that, reinforcing, not replacing, human capabilities.

Jan 1, 1987