Search Documents

By Summers D. A.

A mining machine has been designed and fabricated to mine coal from room and pillar operations combining high pressure waterjet cutting and mechanical fragmentation. Waterjets are used to slot the coal face with an advancing plow wedge then breaking out larger coal pieces. The machine has the following advantages: - simply built around a disassembled longwall chock and gathering arm loader apron; - few moving parts which are simply and inexpensively maintained; provides immediate roof support in the face working area; - coal produced is larger, with resulting lower preparation cost; - no dust is generated; - risk of spark generation is virtually eliminated.

Jan 1, 1992

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques had been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

By H. G. Stephenson, D. Castendyk

Open pit anthracite mining at the Canmore Creek Mines, Canmore, Alberta, south of Banff National Park, resulted in several pit lakes by the early 1970’s. To enable future mining opportunities in the Rocky Mountains, operators decided to reclaim the site into a non-polluting landscape which would provide a memorable outdoor experience for residents and visitors alike, and would preserve wildlife habitat. Reclamation began with the stabilization and revegetation of spoil piles adjacent to Canmore Creek, and the backfilling and revegetation of Canmore Creek Mines No. 1 and 2 to create “Salamander Pond.” The company dammed the outlet of an open pit at Canmore Creek Mine No. 3 to raise the water level and create Quarry Lake. Reclamation concluded in 1980 when the Town of Canmore took ownership. Quarry Lake is now the centerpiece of 293-acre Quarry Lake Heritage Park, a popular destination for swimming, hiking, and fishing, visited by about 400 people on summer days. The Alberta Environment Conservation Authority described this as “The best mine reclamation in Western Canada.” Quarry Lake is an exceptional example of walk-away, pit lake closure, where the mining company created a valued post-mining asset and was released from future liabilities. INTRODUCTION One of the most important environmental issues associated with contemporary open pit mining is the closure of mine pit lakes, and the perpetual legacy these lakes can potentially generate. Ideally, successful pit lake closure includes the following: (i) the water quality within the pit lake, plus surface water and groundwater discharging from the pit lake, meets pre-mining, or other acceptable water quality conditions of the receiving environment, (ii) the termination of all active treatment processes, (iii) the return of the pit lake to the government for long-term care and maintenance, (iv) the release of the mining company from all future liabilities associated with the pit lake, (v) the return the environmental bond to the mining company, and (vi) the reuse of the pit lake for some post-closure, beneficial purpose. The achievement of these goals is known as “walk away, pit lake closure.” Peer-reviewed, publications of successful walk away, pit lake closure provide mining companies the ability to address public concerns regarding the safety of pit lakes which commonly occur during the permitting, operations, and closure phases of mining. To date, most published work on walk away, pit lake closure work has occurred in the coal mining sector in Germany and Australia (McCullough et al., 2009; Jones and McCullough, 2011; Kumar et al., 2013; Schultz et al., 2013). However, in North America, examples of walk away, pit lake closure are not widely discussed in the literature despite there being excellent examples from the coal mining sector in Alberta, Canada (e.g. Pleasure Island, Black Diamond, East Pit, Sphynx, Robb, Lovette, Siltstone, and Sterling), and from the iron mining sector in Minnesota in the United States (e.g. Portsmouth Lake, see MNDNR, 2018). Although seldom included in discussions of pit lakes from the metal and coal mining sectors, the aggregate and fabricated-stone mining sectors also produce pit lakes, and there are numerous examples throughout North America where these pit lakes have been successfully closed and transformed into post-mining resources. The difficulty of finding these good examples in the literature makes it challenging for companies to respond to public and regulatory questions regarding pit lake closure and reuse. As such, there is a pressing need document the motivations and approaches used in examples of successful, walk away, pit lake closure in North America so that the mining industry at large can learn from these examples and can better address public concerns.

Jan 1, 2019

By Earl G. Hoover

For most geologists and miners the term "asbestos" refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for? uses where incombustible, nonconductive or chemically resistant material is required. The United States Mining Enforcement and Safety Administration (MESA) specifically refers to the naturally occurring minerals chrysotile. amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as "asbestos" if the individual crystal fragments have the following dimensions; length -greater than 5 micrometers, maximum diameter -less than 5 micrometers, and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer causing agent) it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment.

Jan 1, 1978

By Harry Asche

Tunnels are frequently specified by owners to be designed to a structural code, often a bridge code. In the USA, AASHTO have created a tunnel code, based on structural principles, the AASHTO LRFD Tunnel Design Specification. The Load Resistance Factor Design method (LRFD) described in the AASHTO title is an approximation to the probabilistic design of structures, based on the independence of load and resistance. This methodology is well known to be problematic in geotechnical design, but it is widely used. The paper considers the difficulties of this approach and describes alternative approaches that would result in more appropriate designs for tunnels.

Jun 13, 2021

By K. Muralidharan, P. R. Rao, M. Momayez, K. A. Runge

The evolution of trapped geothermal heat in hot underground mine along with emission of toxic gases and dust during mine activity makes the mine environment unfavorable is hazardous to worker’s health. This imposes significant demand on cooling and ventilation systems. As a result, substantial costs are incurred while implementing environmental regulation processes to dissipate the heat and provide comfortable working conditions. Thus, as an alternative, the development of cost effective materials to act as efficient thermal insulators is on the rise. Thermal conductivity is an important property that is a direct measure of a material’s ability to facilitate/deter heat flow. In addition to their superior chemical resistance, adequate mechanical strength, abrasion and fire retardant as well as environmental benefits in comparison to existing building materials such as ordinary Portland cement, aluminosilicate based geopolymers are now gaining widespread interest as promising thermally insulating and sustainable materials. This paper begins with an overview of geopolymers, transitioning into a discussion of recent developments in the field of geopolymer development as a thermally insulating material broadly classified into: filled geopolymers and porous geopolymers resulting in structures with enhanced ability to impede heat flow.

May 9, 2020

By G. L. Simmons.

Many large. low-grade (refractory) sulfide gold resources exist in Nevada and other parts of the world that are not amenable to concentration by conventional flotation practice, Over the past several years Santa Fe Pacific Gold (SFPG) has investigated flotation process options to economically treat low-grade refractory resources of this type at Lone Tree and Twin Creeks. Conventional flotation technology applied to the original high-grade gold resources at Lone Tree and Twin Creeks was initially unsuccessful. Review and analysis of auriferous (gold-bearing) iron sulfide mineralogical characteristics and flotation chemistry provided a fundamental understanding that led to the development of a new flotation process that SFPG refers to as N2TEC. This paper discusses the development of this technology and compares N2 TEC results with conventional flotation practice.

Jan 1, 1997

By Paul D. Tomlingson

An effective maintenance program ensures the adequate availability of production equipment. In turn, this availability enables production to maximize utilization and successfully meet production targets. An overall production strategy is necessary to draw all departments toward this common effort. Only then will production targets be met. From the maintenance view this means that production must comply with PM and repair schedules. Purchasing must supply parts and materials on time. Mine engineering must not overwhelm maintenance with non-vital construction. Accounting must provide correct, timely cost information - - etc. This strategy - - its content, effectiveness and enforcement is the responsibility of the mine manager . . . his alone. This paper describes a successful approach to maintenance within this strategy.

Jan 1, 1979

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

By Jason Swartz, Gerardo Gomez, Henry Leighton

San Antonio has experienced sustained growth for decades, putting increased pressure on existing wastewater infrastructure. In June 2013, San Antonio Water System (SAWS) reached a Consent Decree agreement that requires significant improvements to the wastewater system over a 10-year period to reduce Sanitary Sewer Overflows. One of the critical projects was the W-6 Upper Segment Tunnel project to reduce sanitary sewer overflows on an existing sewer main running through Lackland Airforce Base. The replacement project consisted of a new tunnel nearly 29,000 LF of primarily 104" FRP. The project also includes nine shafts and multiple trenchless crossings to make near surface connections to the new works.

Jun 23, 2024

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860's by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

By Joel K. Waterland

The Homes take Mining Company at Lead, South Dakota has a yearly production of 1,868,741 tons of ore produced from horizontal cut-and-fill stopes and timber cut-and-fill stopes. This production, in addition to the necessary development (drifts and raises), requires 5,168,271 feet of drilling annually. The rock for the most part consists of quartz; mica schist; and cummingtonite schist; and must be considered as relatively hard. Penetration rates average about 15 inches per minute using an operating air pressure of 100 psi. The rock is tough, rather than brittle, and dulling occurs quite rapidly. The average regrind period is approximately 19 feet per regrind using a 1-7/16 inch carbide bit. At the present time, all drilling is accomplished with 2-5/8 inch bore airleg mounted drills, and 2-3/4 inch and 3-inch diameter bore -stopers (raising only). These machines are all direct striking, with 4-1/4 inch chucks. 7/8-inch hexagonal carbon drill steel with forged collars are used in conjunction with 1-7/16 inch multi-use, threaded, carbide bits. 62,793 rods, and 16,234 bits are used to maintain the yearly production. The number of rods noted are the rods that were sent: underground, both new and reconditioned.

Jan 1, 1963

By G. J. C. Young

In 1986 the city of Johannesburg celebrates its first century of existence. The fact that the city was founded to exploit the gold deposits which underlaid it, prompts this review of the gold process development in the mining industry of South Africa. Clearly a complete history of, the gold recovery process to date is not called for and it is proposed therefore to outline the most significant developments which have taken place since the middle 1930's, that is to say the last 50 years or so. Prior to this period the industry had seen the development of comminution processes employing cone crushing in closed circuit with vibrating screens followed by grinding in rotating mills and the gradual disappearance of stamp mills. The all sliming process was well established as a viable route and continuous dewatering in thickeners, continuous leaching and filtration were serious rivals for the earlier batch processes. Continuous processes for gravity concentration had also been developed and the recovery of gold from pregnant solutions employed cementation on zinc dust as opposed to shavings. Thus at the beginning of the half century under review the industry had adopted, or started to adopt, many of the processes still accepted as modern practice. However in some areas little change was evident this was especially so in the smelthouse where some thirty more years were to elapse before the hand stoked coal fired calcine and reverbatory furnaces were replaced by more environmentally acceptable electric furnaces. The most significant feature in recent history has been the mining of progressively lower grades of ore and the retreatment of tailings from earlier operations, much of the latter comprising tailings only a decade or even less in age. Notable among these operations are those on the East Rand near Springs in the Transvaal, in the Orange Free State at Welkom and more recently, massive reclamation of tailings close to the city centre itself. The carbon in pulp (CIP) process has been much publicised in recent years and all new plants erected during the 1980's have adopted this route for gold recovery. However the major proportion of tonnage milled in the industry is still subjected to the more traditional process of liquid solids separation by vacuum filtration. The discussion that follows will centre largely on the developments in the traditional process route, which for the sake of completeness is listed below: Comminution Dewatering Leaching Liquid solids separation Gold recovery Smelting

Jan 1, 1985

By Brian T. Hamilton, Richard Piliounis, Cian Murphy

"The Eglinton-Crosstown Light Rail Transit line is a 19-kilometre corridor with a 10-kilometre underground portion currently being constructed by Metrolinx in Toronto through a densely populated urban environment. Tunneling works are being completed through two separate design-bid-build contracts that include consideration for a phased handover to a follow on contractor who will take ownership of the tunnels, including warranties, and will complete the stations and remainder of the system through a PPP delivery model including maintenance of the system for 30 years. Warranty provisions, settlement apportionment, tunnel leakage, potential delays and conflicts between contractors are just some of the risks the team managing tunnel contract integration had to consider when developing the PPP contract. This paper will present an overview of how these risks were assessed and allocated through the contracts and the strategies adopted to minimize risks to Metrolinx while ensuring successful procurement was maintained. INTRODUCTION The Big Move is a 25 year, $50 billion ($-CAD) plan for coordinated and integrated transportation in the Greater Toronto and Hamilton Area (GTHA) in Ontario, Canada. This plan has been initiated by Metrolinx, a division of the provincial government of Ontario, and its vision, goals and objectives are rooted in creating a high quality of life; a thriving, sustainable and protected environment; and a strong, prosperous and competitive economy for the GTHA. The Big Move will triple the length of rapid transit service in the GTHA to 1,725km, significantly increase the percentage of the GTHA population living within two kilometers of rapid transit, reduce commute times to an average of 77 minutes per person per day and decrease greenhouse gas emissions from passenger transportation per person by 29%. Work is currently underway on several projects and more than $16 billion ($-CAD) of the planned investment has already been committed. A key project that forms part of this commitment is the Eglinton Crosstown Light Rail Transit (LRT) Project which is being delivered in the City of Toronto under Metrolinx’s Rapid Transit (RT) Program. This complex and sizeable undertaking has been broken into a number of separate contracts comprising: LRT Vehicles contract; Eglinton West Tunnels Project; Eglinton East Tunnels Project; and a Public-Private-Partnership (PPP) contract to complete the underground stations, at-grade stops, all rail infrastructure and systems and to maintain the entire system for 30 years. The PPP contract, which includes an initial capital portion of approx. $5.1 billion ($-CAD), has recently been awarded to Crosslinx Transit Solutions, a Special Purpose Vehicle (SPV) consortium comprised of SNC Lavalin, Aecon, Dragados and EllisDon."

Jan 1, 2016

By Eva K. Fernandez, Paul Y. Louie, Derek S. Adams, Renée L. Fippin

The Folsom Area Stormwater Improvement Project is part of SFPUC’s flood resilience efforts under the Sewer System Improvement Program. This 4,000-foot-long, 12-footinside- diameter tunnel will help reduce the risk of flooding in San Francisco’s low-lying Inner Mission neighborhood. The project is in a high seismic hazard zone and extends through a complex geologic corridor that includes full-face soft, compressible Bay Mud, Colma Sands, and full-face rock with several stretches of mixed-face conditions. Additional challenges include removal of 99 piles beneath an existing box sewer, tunneling under commuter rail tracks, and an underground tie-in. This paper examines these challenges and how they are being addressed.

Jun 13, 2023

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

A numerical investigation of the effect of pore pressure regime on the safety factor and the critical failure mechanism is presented for fly ash storage facility. Pore pressures’ measurements from standpipe piezometers and pore pressure estimated from seepage analysis are used to compare the factor of safety for a fly ash slope. This was applied for considering static and seismic scenarios. A probabilistic approach was applied to account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation. Slope stability analysis is conducted in two and three dimensions, adopting the limit equilibrium analysis approach, and also a finite element seepage analysis, to assess the stability of the slope. The two-dimensional cross-sections were extruded to three-dimensional models to estimate the factor of safety and associated shear failure. The results from the performed analysis suggest an increase in safety factor values of 5%.

Mar 27, 2024

By T. W. West

During the design and construction of a coal preparation facility, there are many items that can cause serious problems if not properly handled in the early stages of a project. These problems can be a detriment to smooth owner/ contractor relationships, the designing of a flow sheet, the selection of equipment, the design of the facility, the maintenance of schedule and budget, and a smooth start-up. It is the purpose of this presentation to identify some of these problems and to suggest steps that can be taken to reduce or eliminate their impact.

Jan 1, 1977

By Don Phelps, John Hawley, David P. Field

In recent years observational techniques of tunneling have become increasingly popular methods to facilitate complex underground infrastructure projects. The traditional design and construction management practices developed in Europe have been adapted for application in North America to suit a more restrictive management and legal culture. This paper will discuss three recent projects, the San Diego Mission Valley East Extension, Washington Dulles International Airport People Mover, and the Seattle Beacon Hill Station and Tunnels, with the objective of identifying the challenges of applying observational tunneling methods to established contractual practices in North America.

Jan 1, 2005

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Patrick Maier, Gregory E. Bogin Jr

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. As a result, the severity of mine explosions ranges from minor damage to loss of lives and permanent mine closure. Experimental results have shown that the inclusion of obstacles can significantly increase the flame propagation velocity by inducing turbulence. This research focuses on explosion experiments in a 71 cm diameter, 30.5 m long reactor that includes rock piles as obstacles along with developing the corresponding CFD model that captures the observed flame behavior and interaction with the obstacles. The rock rubble increases the flame front propagation velocity by 500% compared to the maximum velocity observed in the empty reactor experiments. The 2D and 3D CFD models predict the experimental flame front propagation velocity, whereas the 3D model shows a more explicit conformity than the 2D model. Although the computational time to complete the simulation is much less for the 2D model than for the 3D model, the 2D model is not sufficient to simulate cases with rock rubble since it cannot capture the propagation of the flame through the small voids between the rocks with the same effective blockage ratio as the 3D model. The validated CFD model can be scaled up to simulate methane explosions in full scale mine and industrial settings.

Nov 20, 2023

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015