Search Documents

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida phosphate and Western phosphate process tailings to recover upgraded phosphate concentrates. After physical and mineralogical characterization, the slurry samples were treated with a broad suite of flocculants with a range of molecular weights and anionic functional groups. Parameters investigated included pH, dispersant and flocculant types, and dose; conditioning parameters and settling times were, for the most part, held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. Single-stage tests using reagents with low to medium anionic characteristics produced upgraded phosphate concentrates at moderately elevated pH. Two- stage site-blocking tests, in which low-molecular-weight flocculants were used as site-blocking agents, gave improved results.

Jan 1, 2002

By Robert L. Runkel, D. Kirk Nordstrom, James W. Ball

Low-flow reactive-transport processes in Wightman Fork downstream of the Summitville Mine, south-central Colorado were simulated using the OTIS and OTEQ solute-transport models. The simulation was calibrated using data from a synoptic study conducted during October, 1998. Discharge over the 8-km reach from just below the mine site to the Alamosa River confluence ranged from 0.077 to 0.17 m3/s; travel time was 10.7 hours; pH ranged from 4.6 to 5.7. Simulations revealed that mass balance for SO4 was maintained, and that pH, Fe, and Al were non-conservative. Simulations allowing hydrous ferric and aluminum oxide or hydroxysulfate precipitation matched observed water quality conditions more closely than simulations without precipitation.

Jan 1, 2000

By Jens Classen, Thomas Kurth, Karl G. Holter

High performance sprayed concrete equipment installed on two 9.4 m diameter hard rock TBMs enabled a continuous sprayed concrete lining for the entire contour in both tunnels to be performed concurrently with the advancing TBMs. Innovative layout of the sprayed concrete arrangements comprised ring beam constructions each with two independent spraying robots. Each of the spraying robots were independently connected to sprayed concrete pumps, as well as a high capacity concrete logistics system on the backup. The mix designs focused on long open-time, excellent pumpability and tough requirements on strength development. The achieved output capacities of the sprayed concrete amounts to an average of 15 m3 per hour. Peak capacities of 24 m3 per hour have been realized.

Jan 1, 2003

By Shelley M. Burg, Dennis K. Poulton, Robert B. Gordon

This project includes the excavation and concrete lining of approximately 18 900 m (62 000 ft) of 5.5 m (18 ft) finished diameter subway tunnel for the Los Angeles MTA. The project required that four soft ground headings be excavated from a single shaft located near the mid point of the tunnels. The tunnels were classified "gassy" during the excavation phase. Because of the contract schedule requirements and the limited urban work site available, many logistical problems had to be overcome during the project while excavation was accomplished at a record setting pace. Some unique project features include the muck handling system and an access shaft using a high strength tieback support system. In order to accomplish the work, an extensive effort to plan and construct the main work site was required.

Jan 1, 1995

By Richard Louis Viner, William D. Leech, Walter A. Mergelsberg

With the construction management team established and a full funding agreement secured the Washington Metropolitan Area Transit Authority (WMATA) now has the manpower and the financial resources to continue Metrorail construction into the 1990's. This paper describes WMATA's new role as construction manager after the transition from Bechtel Associates and gaining the full funding agreement with the Urban Mass Transit Administration (UMTA) and regional governments to complete 84.7 Metrorail miles (136km). The authors review the most recent station and line tunneling projects. WMATA's contractors have employed the state of the art soft ground and hard rock tunneling equipment and methods - an earth pressure balance TBM, a closed face TBM, and the New Austrian Tunneling Method (NATM). In final, the paper previews future underground work to be let under the funding agreement.

Jan 1, 1987

By Peter A. Burger

The Greenvale Orebody comprises a series of contiguous lateriteprofiles developed terrace-like during the Cainozoic over a serpentinized harzburgite intrusive emplaced within Proterozoic schists. Each terrace displays individual characteristics of metal distribution. Topographically higher (older) profiles have been partially eroded and metal concentrations reworked. Within the laterite profile, metals have been concentrated or depleted according to their relative solubilities. At tropical temperatures, acidic meteoric waters have progressively depleted the ultrabasic parent rock of Si and Mg, leaving A1 and Fe to form a surface duricrust. Ni, Co, Mn and Cr have accumulated in the lower and middle levels of the weathering mantle. Only Ni and Co have accumulated to exploitable grades. Lateritization has evidently proceeded over a considerable portion of the Cainozoic and may be still continuing.

Jan 1, 1979

By F. F. Aplan, C. E. Raleigh

Three run-of-mine bituminous coals, ranging in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µm), -100 mesh (150 µm), and -400 mesh (37µm) feed particle sizes with selected pyrite depressants and a dispersant. For the three coals tested, pyrite and ash -forming minerals were usually rejected best at -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µm) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1992

By I. K. Kapageridis

Environmental management and planning requires the integration of large volumes of disparate information from many sources and the analysis of this information with efficient tools for assessment and evaluation. Effective methods of communication that allow interactive participation in the planning, assessment and decision-making processes are also very important. The VULCAN software package from Maptek (Pty) Ltd comprises a large number of 3D graphical tools within an interactive 3D interface called ENVISAGE. These tools are designed and developed to help engineers and scientists to identify and solve environmental problems. The combination of VULCAN 3D Software and the I-SiTE 3D Laser Imaging system leads to powerful solutions for environmental management. This paper presents the capabilities of this integrated system and its applications for environmental management.

Jan 1, 2002

By David Lunt, Paul Messenger, Peter Allen

The Rawas Gold Project in Indonesia has a high silver ore with a ratio of approximately 25:1 Ag/Au. Four process flow­sheets were considered during the development phase, ie. full Merrill Crowe, CIP, CIP with zinc cementation of eluate and a hybrid Merrill Crowe - CIP circuit. The process plant was constructed using a CIP circuit with zinc cementation of eluate. Unusual aspects of the design include an elution circuit designed to strip three batches of car­bon per day and an elution column designed to operate with either upward or downward solution flow. Significant improvements implemented since starting up the plant include the use of local materials and labour for relining the mill, a change from lime to caustic soda for pH modification and the elimination of caustic soda dosing to the elution pre-soak step.

Jan 1, 1998

By B. Stewart, J. R. Warneke

The productivity of underground mines has increased dramatically since the introduction of continuous miners. A variety of new hazards have developed as a result. In the spring of 2004, Mine Health and Safety Administration (MSHA) held a workshop to brainstorm ideas to decrease the number of injuries associated with continuous miners. One of the main areas of discussion at the workshop was “trailing cable-handling injuries.” The method of handling the power cables over the years has changed very little while the technology and uses of continuous miners has advanced dramatically. This paper will discuss the main ideas brainstormed at the MSHA continuous miner (CM) trailing cable handling workshop and the history and root causes of cable-handling injuries, as well as proposed ideas developed at the National Institute for Occupational Safety and Health (NIOSH) to alleviate some of the cable handling issues.

Jan 1, 2006

By G. Orhan, C. Arslan

The possibility of producing metallic chromium from Cr2O3 via the aluminothermic route, with no external energy supply, was the subject of this laboratory-scale research. The experimental study focused on investigating the individual effects and quantitative optimization of the charge contents, i.e., the additions of CrO3, Al powder and CaO (or BaO). The highest chromium recovery of 98% was attained with the additions of 12% CrO3 and 1.2 times the stoichiometrically required amount of Al powder. The optimum CaO addition giving the highest chromium recovery was found when the CaO/Al weight ratio in the charge was equal to 0.3. When BaO was used, however, 95% Cr extraction efficiency was obtained at a BaO/Al weight ratio of 0.15.

Jan 1, 2000

By David R. Baughman, John C. Gathje, K. C. Oberg, Gary L. Simmons

Santa Fe Pacific Gold Corp. conducted pressure-oxidation pilot plant studies on refractory carbonaceous gold ores from the Twin Creeks Mine in Nevada. The tests were conducted at Hazen Research Inc., Golden, CO, during 1993 and 1994. Laboratory investigations using CIL cyanidation after batch pressure oxidation demonstrated gold recoveries of 90% to 95%. However, pilot plant testing showed that several of the same ore types responded very poorly, with gold extractions of only 45% to 75%. Plant testing was suspended for approximately four months while extensive research was conducted to determine why these ores responded poorly and to identify potential solutions. This paper describes the batch and pilot plant test results, the extensive research activities that eventually identified the cause of the gold recovery problem and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions. Final pilot plant results showed gold recoveries that were consistently greater than 90%.

Jan 1, 1999

By Tim Cleary, Steve Skelhorn

The 9th Line / 16th Ave tunnels are part of a $700 million expansion of the York Durham Sewage System, north of Toronto. The 15 km of tunnels presented many challenges, including glacial and postglacial deposits, at depths up to 55 m. Due to high hydrostatic heads, the Owner specified EPB tunnelling, however, an alternate was proposed utilising rib and lagging tunnels, combined with a de-watering scheme. State of the art technology was utilised with a new Lovat TBM, incorporating PLC control, soft start water-cooled motors and a head designed to tackle the mixed ground expected. The 9th Line tunnels were completed in 2002. Subsequently the second section of tunnel along 16th Avenue has been awarded to the Joint Venture. This paper presents a case history of the soft ground tunnelling, including design elements, tunnel systems and TBM operations.

Jan 1, 2003

By Terry M. Hertel

Zortman Mining has spent approximately three years evaluating the metallurgy of the sulfide ores from the mining area of the possible expansion project. As the test program proceeded, an interesting series of events took place which changed the scope of the work. During the agglomeration work, one of the control columns was inadvertently set up without the addition of lime to the material prior to loading and subsequent leaching. The gold recovery from this column was comparable to those columns that had a lime addition of 10 pounds per ton of ore. In fact, the gold recovery curve had a much steeper slope than those of the other columns. Furthermore, the pH of the pregnant liquor from the "no lime" column recovered to typical levels as fast as the solutions from the "lime" columns. These observations led to the concept that rinsing the ore with water prior to cyanide leaching could be advantageous to the heap-leach process.

Jan 1, 1992

By R. D. Miller, L. Schulte, J. Davenport, D. W. Steeples

Shallow seismic reflection methods were successfully used to delineate the subsurface extent of roof failure associated with the dissolution mining of a 120-m (400 ft) deep and 60-m (200ft) thick salt bed in central Kansas. Surface subsidence at North American Salt's Hutchinson, KS, salt-dissolution well field represents a potential risk to surface structures and transportation facilities. Three intersecting common depth point (CDP) seismic reflection profiles, targeting the subsurface around an actively subsiding sinkhole, possess sufficient resolution to delineate the horizontal and vertical extent of subsurface rock failure associated with the subsidence. The three seismic profiles showed a disturbed subsurface area 90 to 105 m-diam (300 to 350 ft-diam) at a depth of between 60 to 75 m (200 ft and 250 ft). Confirmation drilling verified the interpretation of the seismic data. The seismic reflection method has the potential to resolve disturbed subsurface areas greater than 23 m-diam (75 ft-diam) at this site.

Jan 1, 1994

By James M. Prudden, E. P. Jucevic

The Divide mining district occupies the center of a Tertiary caldera hosting the famous Divide silver lode and the crosscutting Gold Mountain mines. The northwest-southeast trending silver lode hosted ore with typically a 100:1 silver:gold ratio, high molybdenum content and argillic alteration dated at 16.5 m.y. within the Fraction Tuff. The east-west trending Oddie Rhyolite flow dome at Gold Mountain experienced possibly several periods of resurgence with repetitive silicification, brecciation and attendant precious metal deposition forming stockwork type mineralization. Silver-gold ratios average 10:1 for the mineralization phase of this 16.4 m.y. intrusive event. Similar chalcedonic mineralization registering a 3:1 silver:gold ratio cements conformable breccias within the Oddie Rhyolite basal flows unconformably overlying the Siebert Tuff on the northern flanks of Gold Mountain. Gray and red chalcedonic breccia matrix in the King Tonopah member of the Fraction Tuff contains a 50:1 silver :gold ratio.

Jan 1, 1990

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple entry section of the Bruceton Experimental Mine. Chambers filled with one hundred and eighty kilograms of Pittsburgh seam coal were ignited and allowed to burn until well developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires and the quantity required to extinguish the fires compared to the amount of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 22 L to extinguish the coal fires, while two commercially available additive-water solutions required an average of 30.6 and 30.3 L, respectively. The average amount of water required to extinguish the fires was 28 L. An analysis of covariance, using the thermal energy of the coalbed, Q, to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, while the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 1992

By J. J. Moore, B. Mishra, D. L. Olson

The production of radioactive and reactive metals, such as plutonium, uses various pyrometallurgical techniques that generate significant quantities of waste salts contaminated with hazardous, reactive or radioactive materials. Health concerns, environmental regulations and economic considerations require proper mitigation processes to recover the valuable components and for recycling or unrestricted release of these salts. The Oxygen Sparging Process converts soluble metal halides, such as chromium-, plutonium-, cerium chlorides, into insoluble oxides and/or oxychlorides which can be consolidated and separated for long-term storage or further processing. The matrix salt phase, viz. calcium and/or alkali chlorides, are clean after oxygen sparging and fit for recycling. This method has been described and its optimized parameters discussed to show that RCRA regulated elements, such as, chromium, lead, cadmium, etc. report to the consolidated phase making the salt recyclable. Salt Scrub Reduction Process for the recovery of radioactive and RCRA metals from the waste salts has been developed. The process uses a Ca-Ga intermetallic alloy which recovers over 98 percent of the reactive metals. The matrix salt phase in this process, viz. calcium or alkali metal chlorides, are clean after salt scrub reduction.

Jan 1, 1995

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987