Search Documents

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Most, if not all longwall gobs contain explosive gas zones (EGZs), i.e., zones of explosive methane-air mixtures that can cause – and have caused – mine fires and explosions. If the coal is prone to spontaneous combustion, oxygen penetration into the gob must be avoided. This paper summarizes the significant research findings from five years of computational fluid dynamics (CFD) modeling research conducted at the Colorado School of Mines (CSM) under funding from the National Institute for Occupational Safety and Health (NIOSH). CSM Researchers have developed CFD modeling techniques to identify where and under what circumstances EGZs can form in longwall gobs and how EGZ formation and oxygen penetration depend on the ventilation method, face and bleeder ventilation parameters, injection of inert gases and the operation of gob ventilation boreholes. Recognizing these explosion and fire hazards is an important first step in improving the safety of longwall coal mines. CSM modeling research has shown that EGZ formation can be effectively controlled by adjusting ventilation parameters, choosing the proper ventilation pattern and injecting inert gases where necessary. INTRODUCTION In a project sponsored by the NIOSH Office of Mine Safety and Health Research, researchers at the Colorado School of Mines have examined gas compositions and flows in longwall gobs in order to assess explosion and fire hazards. Since gob areas are inaccessible, researchers developed a series of computational fluid dynamics (CFD) numerical modeling tools to characterize these hazards. A variety of CFD models were developed to cover progressively sealed as well as bleeder ventilated gobs for both coal and trona mines. The explosion and fire hazards posed by EGZs in longwall gobs can be summarized as follows.• If the EGZ lies closely behind the longwall face, flames and pressures from an explosion can penetrate the shield supports and reach the active face area, creating blast trauma, burn hazards and toxic, unbreathable atmospheres. • EGZs can be pushed around inside the gob by roof collapses and cave-ins. If they get pushed out into the face area, sudden methane inundations and explosion hazards in face areas can result. • Fresh air flowing into the gob can create an explosion hazard as the gas composition in the gob moves from fuel-rich inert to explosive, creating EGZs. • Ignition sources inside the gob can be frictional ignitions or spontaneous combustion. • Bleeder ventilated gobs are surrounded on all sides by an EGZ that forms along the fringe areas between the fresh-air ventilated bleeder entries and the methane-rich interior of the gob. It is suspected that diffusion flames can propagate rapidly along these EGZ fringes if an ignition occurs"

Jan 1, 2015

By X. X. Jiang

An efficient recovery of finely divided magnetite particles of 400/500 mesh from a mixture of magnetite/silica particles has been investigated by imposing a delicate balance between centrifugal and surface tensional forces on these particles. The effect of centrifugal force, surface tensional force, density and size of particles on the overall metallurgical efficiency has been examined. A mathematical model based on a momentum balance on the particles at the liquid/liquid interface has been developed. The validity and limitations of the model are discussed in view of the experimental results obtained.

Jan 1, 1992

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By N. Sahin, K. Baris, A. Ozarslan

This paper aims to assess the current and future role of coal in energy strategy of Turkey and evaluates the compatibility of the policies to the EU energy policy and strategy. The Turkish government set targets to utilize more coal reserves of the country in next decades. However, the country is also in the process of becoming an EU Member State, hence, it is expected that the energy policies have to comply with the EU. Moreover, Turkey ratified Kyoto Protocol, thus the country should limit greenhouse gas emissions. Clean Coal, Carbon Capture and Storage (CCS) technologies are expected to become an important instrument for the mid-term reduction of CO2 emissions from coal-fired power plants. An alternative technique to the conventional CCS methods is CO2 sequestration by mineral carbonation. Turkey has significant resources of magnesium silicate minerals (olivine, serpentine) deposits which can be utilised in CO2 sequestration by mineral carbonation method.

Jan 1, 2011

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021

By Kristian E. Waters, Hao Ma, Haibei Wang

Heavy metal ions exist in waste effluents including mining tailings, manufacturing discharges, and smelting and metal plating process wastes. Various methods are available to treat industrial effluents containing high levels of metal ions, but when confronted with wastewater that has low metal ion concentration below 500 mg/L, most techniques suffer from low removal or separation efficiency as well as high operating cost. ELM-based techniques can be used to solve these problems.

Apr 1, 2023

By Everett M. (Original by) White

Numerous articles have been written about the coal mine ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers&apos; Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio&apos;s, and in 1876 by Maryland&apos;s. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597 deaths. Because of this, the federal government took action and by 1910, the US Bureau of Mines had been established. This was perhaps the most significant change in health and safety for miners during the first half of the 20th century as the USBM concentrated its entire efforts in the study, research, and testing of methods totally directed towards improvement of the health and safety of the miner. After a mine disaster in Illinois, a federal law was passed in 1940 calling for federal coal mine inspectors. Then in 1969, Congress enacted the Federal Coal Mine Health and Safety Act following a mine explosion near Farmington, WV. In 1977, the law was revised and included noncoal mining operations.

Jan 1, 1981

By James J. Scott

Friction Rock Stabilizers, trade name II Sp 1 it Sets&apos;" have been under research and development by the author and the Ingersoll-Rand Company since February of 1973. The United States Bureau of Mines and the Mines Enforcement and Safety Administration as well as many mining companies have cooperated in field testing the device. Split Set rock anchors are distinctively different from the widely used mechanical rock anchors or fully grouted rock anchors. They control ground movement internally in a manner that allows controlled deformation during the early phase of the ground reaction curve but then, as secondary creep develops, anchorage per unit length increases and they serve to strengthen and stabilize the opening for long periods of time. The history of research and development of the Scott Split Set rock anchor system with accompanying laboratory and field test data is presented in this paper.

Jan 1, 1977

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP&apos;s ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By J. P. Fitzgerald

This paper is an accumulation of information on the geology, mineralogy and mining of the Hectorite clay deposit owned by NL Chemicals (U.S.A.), Inc. The mine is located in San Bernardino County, California approximately 35 miles east of Barstow and 1-1/2 miles south of U.S. Highway 40. The region is known as the Mojave Block which is a region bound by the San Andreas fault zone to the southeast and the Garlock fault zone to the North. The faults of both zones are active, vertical faults along which movements are mainly horizontal. Most of the faults within the Mojave Block are high angle faults which trend northwest. They are considered part of the San Andreas fault system and are a result of the right- lateral movement characteristic of this system. The east-trending faults are also high angle faults, along which movement has displaced rock units vertically. Manix fault is the only mapped fault that shows evidence of left slip which is characteristic of the Garlock sys tem to the North.

Jan 1, 1986

By Mike Preston

Attrition scrubbers may not be glamorous, but they are an important and sometimes neglected step in mineral processing. Optimal attritioning will significantly improve the results and efficiencies of subsequent processing steps and can lead to reduced costs and improved product yields. Why is attrition scrubbing used? Attrition means to wear away a surface, typically by friction or abrasion. An attrition scrubber does exactly this, using impellers to force particles against each other, causing intense scrubbing, grinding, abrasion and polishing. This process is not a new concept. It has long been used in the glass industry to remove surface contaminants from silica. But it is also widely used in many areas of mineral processing and other applications including soil remediation and plastics recycling. In mineral separation, for example, the scrubbers help improve yield and efficiencies by preparing feed materials for downstream processes such as flotation, magnetic or electrostatic separation. Inefficient scrubbing can lead to coatings remaining on valuable minerals and decreased yields, as the covered minerals cannot be processed efficiently or are mistaken as waste contaminates and removed. In the example of flotation separation, pre-flotation conditioning uses attrition scrubbers to provide better recovery of minerals while using fewer chemicals. If surface contaminants remain on the mineral, yield is reduced, as the unwanted coating acts as a barrier to the reactants, which make it unfloatable and, therefore, unrecoverable.

Oct 1, 2013

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the National Institute for Occupational Safety and Health (NIOSH) developed a light-emitting diode (LED) area luminaire called the Saturn and conducted a laboratory study using a Fletcher High Dual-boom Mast Feed (HDDR) roof bolting machine. The Saturn luminaire was designed to (1) enhance floor illumination to enable better detection of trip hazards in the interior spaces of a roof bolter and (2) reduce glare that has typically been an issue of concern on roof bolters. This paper reports on the results of achieving the second objective. The existing roof bolter lighting was the baseline and was compared with three versions of the Saturn luminaire relative to light intensity (100%, 75%, and 50%). Discomfort and disability glare data were obtained from 30 participants that comprised three age groups. Discomfort glare perceptions were obtained using the De Boer rating scale, and disability glare was quantified by using Mars Letter Contrast Sensitivity tests. Discomfort glare was reduced at least 3 levels with all Saturn versions. Also, a predictive model was used to estimate discomfort glare, and the results were similar. Disability glare was the least for the Saturn’s 50% intensity, and all Saturn versions had significantly less disability glare than with the baseline lighting. Veiling luminance was calculated and used as another indicator of disability glare. Veiling luminance was 28 to 42 times greater with the baseline lighting as compared with that of the Saturn lighting. Lastly, visibility levels were calculated. The Saturn versions were 4 to 6.5 times better in terms of visibility level.

By Charles B. Escapule

The first successful heap leach of silver ores in the State of Arizona has been under continuous operation since early 1976 at the State of Maine Mine, two miles southwest of Tombstone, Arizona. The silver produced from leaching old mine dumps at this property vas the first in the Tombstone mining district to achieve a 999+ purity. While cyanide leaching of silver and gold ores is a time-proven accepted practice, a relatively new method of treatment called "heap" leaching was employed. Heap leaching is a comparatively inexpensive fast way to recover precious metals from low grade material.

Jan 1, 1981

By G. F. Jenkins, P. S. Hobden

Toronto as a geographical area provides an exceptionally wide variety of subsoil stratiphication. Tunneling consequently required a very wide range of adaptabilities to meet its changing conditions. This discussion will provide a summary of work performed in both earth and rock formation using three of our recent works to describe a Contractor&apos;s experience. The general subsoil stratigraphy is known to consist of deposits laid down during the Illionian Glaciation followed by the Samgamon Interglacial Stage and finally the Wisconsin Glaciation. All these deposits are underlain by shale bedrock of the Dundas formation. As a whole the Dundas formation is predominantly a greyish blue, thinly bedded shale. The engineering characteristics of the shale vary considerably, however, between a blue clay (argillaceous) shale and a much lighter (in colour) silty and sometimes sandy (arenaceous) shale, and occasional limestone layers. The Illionian deposits are usually found to be layers of pebbly clay till and an overlaying layer of contorted varved-clay. These glacial deposits can be overlain by a thick layer of sandy silt to silty sand which is identified as the Samgamon Interglacial sediments. Because of the action of erosion the Wisconsin till sheets, many times separated by interstadial sands, can vary greatly in their number of layers from zero to three or more.

Jan 1, 1997

By Stavros H. Constantopoulos

Mediterranean regions such as Greece, Turkey, Cyprus, Corsica and New Caledonia have experienced epidemics of malignant mesothelioma as a result of non-occupational, ??domestic?? exposure to tremolite asbestos and fibrous erionite. This exposure to tremolite asbestos and fibrous erionite is typified ??domestic?? due to its prevalence in regions with natural deposits of tremolite asbestos (or fibrous erionite) where the material from tremolite asbestos or fibrous erionite is used for domestic applications such as whitewashing. However, these exposures may be useful in examining the potential consequences of even small amounts of amphibole asbestos fibers in the ambient air. It can also elucidate the effects of fibers that behave like amphibole asbestos. However, this type of exposure is not useful for studying the potential effects of small amounts of asbestos in the ambient air of big cities due to the differing nature of the fiber types and modes of exposure between the regions. © 2008 Published by Elsevier Inc. Keywords: Tremolite asbestos; Erionite; Domestic; Environmental; Exposure

Jan 1, 2007

By M. J. dos Santos

"INTRODUCTION In his landmark Society for Mining, Metallurgy and Exploration (SME) 2000 writing, “Theory and Design of Sandwich Belt High Angle Conveyors According to The Expanded Conveyor Technology” J.A. Dos Santos generalized the belt conveyor technology to include all possible variations and augmentations including, particularly, multiple belts along a common carrying and/or return path as is the case most notably in the sandwich belt high angle conveyor technology and belt-on-belt type intermediate (booster) drives. Figure 1, excerpted from his writing, represented the proposition of the generalized “Expanded Conveyor Technology,” abbreviated ExConTec.This formed the basis for the generalization which was completed in theory and in math before 2000 and presented by J. A. Dos Santos at the Y2K SME Annual Meeting. The writing can be found in the SME library (Dos Santos J. A., January 2000). While Figure 1 with the supporting mathematical development solved the generalization, it failed to identify the variation that would prove to have the greatest significance. As with most significant developments, necessity is the mother of invention. This is the case with the Adder Snake belt technology, the subject of this writing. BACKGROUND The concept of elevating bulk materials at a high angle using the sandwich belt concept was first introduced in 1951. That introduction did not produce any lasting success. Commercial success was achieved in the 1970s with the Loop Belt, a sandwich belt elevator of C-shaped profile developed by Stephens Adamson of Canada. The Loop Belt was and is the vital element of a conveyor based self-unloading ship system. Such self-unloading ships have had great success achieving unloading rates above 10,000 t/h with Loop Belts of width to 3,048mm (120”). Being strictly of C-profile, Loop Belts could not be adapted to the general high angle conveying path which is predominantly along a straight incline. It was the success of the Loop Belts that inspired the Dos Santos Sandwich Belts of the 1980s. These expanded the Loop Belt capabilities by producing endless elevating profiles that could take the most direct and/or conforming path between the loading and discharge points. Sandwich Belt high angle conveyor systems have seen great success through the years, with more than 200 installations throughout the world."

Jan 1, 2018

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015