Search Documents

By E. G. Williams

Underclays and shales are two natural resources associated with the coal measures. Underclays are widely used as the raw material for refractory, semi-refractory, and face bricks. Shales are useful for sewer pipe and lightweight aggregate. This study concentrates on the geologic controls over the properties of shales for use in the manufacture of lightweight aggregate, and the geologic controls over the properties of underclays for use in the manufacture of bloating ladle refractories. The industrial processes are similar in that both involve the trapping of a gas phase to cause bloating. They differ in that the bloating of lightweight aggregate occurs at lower temperatures (1000-1200°C) than ladle bricks (1350°-1470°C). Lightweight aggregate bloats during an initial rapid firing. Ladle bricks are manufactured by slow firing at 1100°C for up to 80 hours. Bloating occurs when these bricks are reheated to 1350°C . Bloating shales are those which expand twice or more times their original volume during fairly rapid firing. Commercial bloating is usually done by rotary kiln processing or sintering; in both cases the firing rate is much faster than the experimental rate (5/8°C/minute). Bloating results from the entrapment of gasses which are evolved during firing. The material must have adequate viscosity to trap gas bubbles throughout the temperature range of bloating. The finished product contains a high percentage of closed pores with a bulk density between 35-75 pounds per cubic foot. Expanded shale finds its most important use as a substitute for heavy concrete aggregate (crushed stone, sand and gravel) where low bulk density is desired property. The extent of bloating in lightweight aggregate is a function of the mineralogy and chemistry of the shale. Figure 1 shows a corner of the three phase diagram, kaolinite-quartz-(illite and chlorite). Several areas on the diagram are outlined which contain predominantly marine shales, fresh and brackish water shales, and underclays. Each sample was rapid fired and the resulting expansion was plotted on the phase diagram.

Jan 1, 1973

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By J. Walden, S. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

By Orris C. Herfindahl

Every few years we are treated to a battle over trade policy when the Reciprocal Trade Agreements Act comes up for consideration. In 1962 it is especially appropriate to consider the problem of mineral import -policy and the closely related problem of general import policy, for this year's struggle is different from those of the past in two ways. First, proposals have been made which are a substantial departure from past trade agreements legislation, and second, the formation and growth of the Europe Economic is Community may have an important bearing on the kind of legislation that is adopted. But this anticipates what is to come later. My task is to examine the problem of mineral import policy, although we shall find soon enough that general trade policy must be considered in order to get an indication of what is in store for minerals.

Jan 1, 1962

By Carl-Eric Dr. Nilsson

Energy cost for mine ventilation in Sweden is high, especially during winter time when air must be heated. This paper presents the result from a project entitled ventilation-as-required. The term ventilation-as-required means that the required volume of fresh air should be distributed only to such areas, where mining work is going on and to be reduced to a minimum in the rest of the mine. Ventilation-as-required is a monitoring system that controls the operation and capacity of the fans and measure the air pollutant gases, i.e. carbon monoxide, nitrogen and sulphur dioxide at strategic points. It is an active system that responds when equipment is under operation. MITU proposed in 1991 a project to develop a ventiation-as¬required system and such components as transmitters and receivers for the communication between the equipment and the fans. The mining companies, Boliden Mineral AB, LKAB, Outokumpu and Ammeberg Mining Corporation joined the project and have financed a joint research and development programme supported with a grant from the Swedish Government through NUTEK. MITU proposed a second project in 1992 to the mining companies to develop an improved "intelligent" fan for scope ventilation. Boliden Mineral and LKAB joined the project and have financed a joint research and development project supported by the Swedish Government through NUTEK. The Government even made a commitment to support the investment of the first 50 fans ordered with a grant of 25% of the investment cost. The result from projects show that the target set up in the plans is more than achieved, with an energy reduction that exceeds 30% compared to previous consumption. No environmental influence due to reduced ventilation is observed in the stope when work is under progress. Dilution of exhaust gases from diesel fuel decreased from 6.000 m3/L consumed diesel fuels to 3,600 m3/L. The automatic data processing and sensor system is even increasing the security of the work so that it can be done under safer environmental conditions.

Jan 1, 1995

By C. G. Anderson

Historically, the treatment of orebodies for recovery of valuable constituents presents many processing challenges. In a time of heightened environmental awareness, the constraints placed on processing complex orebodies are becoming more and more pronounced. As such, established technologies are limited in their ability to fill the needs of these emerging sources of raw materials. A prime example of this is in processing PGMs from primary sources. Normally, this type of material is found in a nickel-copper-iron sulfide matrix. Typically, these materials are processed by established pyrometallurgical means. However, other options should be considered. Hydrometallurgical processes are available which offer advantages over pyrometallurgical methods. One of these is the nitrogen species catalyzed sulfuric acid pressure leach used industrially by Sunshine Mining and Refining Company. In 1990, laboratory work was undertaken in cooperation with Stillwater Mining Company to test PGM matte materials from the Columbus, Montana smelter. The initial results were very positive, and they led to a design to recover PGMs in a high grade residue and to recover nickel and copper as valuable products. Handling the iron and other wastes in an environmentally safe manner was also successfully investigated.

Jan 1, 1995

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By R. L. Grayson

Compliance standards for respirable dust which are reduced because of high quartz concentrations have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. If, however, the quartz is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.

Jan 1, 1990

By S. Bassignani, D. Ippolito

In Italy at the moment there is a program which involves for the future the exploitation of two uranium mines which are now in the research stage. About one hundred and fifty workers are at present employed in those facilities. An health physics surveillance program is under way and has been designed to fulfill the requirements due to the future exploitation of the two mines. A complete evaluation of the total dose (external + internal) received by the workers will be given together with a detailed analyses of the technical methods employed for such evaluations. The external doses are evaluated on the basis of individual TLD dosimeters, while the evaluation of the internal doses is mainly due to an enviromental survillance program of the radon and radon daughter air concentration inside the mines. The criteria established for the assessment of the sampling procedures, sampling intervals and dose evaluation related to the radon doughter exposure are reported. The external dose received by the workers are lower than 0.2 m Sv~month and the internal exposure less than 6.4 IO-3 J.h.m-3 /year or using the old units 2 WLM/year.

Jan 1, 1981

By David Lynn Passmore

The reliability of mine operators reports to the Health and Safety Analysis Center of the U.S. Deparetment of Labor of days lost from work by injured miners is .267.

Jan 1, 1985

By D. H. De Jager

Fluorapatite is an important constituent of the greater part of the basic and ultra-basic rock members of the Complex. The evidence for and role of primary magmatic processes in the development of concentric zones of dunite, pyroxenite, syenite and carbonatite and its consequent bearing on the distribution of apatite are discussed. The presence of at least two generations of each of the latter three rock types indicates the cyclical nature of magmatic activity. Pegmatitic-metasomatic phases corresponding to the major magmatic cycles resulted in emplacement of pegmatoidal assemblages. The abundance of apatite in the pegmatoid can be traced to the composition of its parent magma and its cooling history. Approximately 2.5 million tonnes of phosphate concentrate are produced annually from ores containing from 10 percent to 25 percent apatite.

Jan 1, 1978

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987

By Gerry Norton

The purpose of this paper is to make the most complete assessment of coal cleaning methods, both process and equipment related to modern-day production and environmental requirements. In order to achieve this primary objective, a number of interdependent aspects of coal cleaning technology require evaluation and analysis. 1.0 CLASSIFICATION OF SEPARATION PROCESSES Processes and cleaning equipment can be categorized according to the important parameters of 1) mechanics of separation, 2) size range application, 3) range or variance in accuracy of separation related to 2) above, and 4) feed-size ratio affecting 3) above.

Jan 1, 1977

By Jon Y. Kaneshiro, Stephen J. Navin, Jerry Ostberg

In 1968, the U.S. Bureau of Reclamation awarded S.S. Mullen Construction of Seattle, the Intake Tunnel (488 m by 4 m diameter tunnel) and Pumping Plant No. 1. In1998, the Southern Nevada Water Authority awarded Lake Mead Constructors (Kiewit of Omaha) a parallel New Intake Tunnel (518 m long by 4.6 m diameter tunnel) and Pumping Plant. Both projects provide water to a thirsty Las Vegas. This paper presents a detailed comparison of the two intake tunnels in terms of grout takes and pressures, geologic mapping and rock quality, grout penetration beyond the excavation line, degree of fracture grouting, and groundwater inflow boundary considerations. The paper provides a comparison of grouting techniques and material developments then and now.

Jan 1, 2001

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

By M. L. Smith

The U.S. Bureau of Mines Cost Estimating System (CES) has been used for prefeasibility analysis and mine cost engineering since 1978. In the past, prefeasibility analysis with CES has involved the solution of regression equations. The new generation of CES uses an object-oriented expert system in a Windows? environment. Knowledge bases are structured around generic mine models which access shared knowledge bases for system design.

Jan 1, 1994

By Charlie Yates, Max Ramey, Kurt Nielsen, Michael Hardy

The Yankee Gulch sodium minerals project (YGP) is a solution mining project operated by American Soda. The mine operates on a federal lease administered by the U.S. Bureau of Land Management (BLM). Commercial operations began in November2000. In 1964, Irv Nielsen discovered nahcolite mineralization where the YGP pilot plant is now located near the Piceance Creek in Rio Blanco County, Colorado (Nielsen, 1969).Development of the project accelerated after Williams Corp., of Tulsa, OK, joined with American Alkali in1996 to form American Soda. Pilot testing by American Soda led to commercial permitting, plant design, construction and startup. Figure 1 shows the location of the Yankee Gulch leases and the location of the upper and lower plant sites.

Jan 1, 2003

By Günther M. Volkmann

Continuous developments in tunneling require knowledge transfer between designers and suppliers to optimize the application of support systems. This collaboration allows the designer access to the latest research results, technical innovations, and support specific measurement techniques as well as the supplier?s experiences on recent projects. Project specific requirements determine the information that can be used to increase support system efficiency, advance rate, degree of safety, or decrease costs. This cooperative effort results in not only an unambiguous tender document, but also an optimized design with reduced risk that is coordinated with safe and high performance construction techniques. This paper will address the benefits of an early collaboration to both the design and the specifications in the tender document by using the A3 Hindhead project (UK) as an example.

Jan 1, 2008