Search Documents

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By C. O. Brawner

A recent advance in slope dewatering-depressurization and stabilization is the use of vacuum assist horizontal drainage. (Brawner and Pakalnis) Horizontal drains have been used for several decades to reduce water pressures in slopes to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by an induced negative atmospheric pressure. A research program included a laboratory model whereby the effects of vacuum drainage were evaluated. Three case studies are described where the technique has been successful. The first is in a rock slope where flows increased from 0.1 1/min. under gravity drainage up to 1.2 1/min, upon vacuum. The second study involves installation of 17 drains placed at a slightly downward gradient to intercept and de- pressurize aquifers under a major tar sand deposit in Canada. The third study was on a large open pit copper mine in British Columbia where flow increased about 30 per cent.

Jan 1, 1984

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill. The design of the Hicom mill is unique. Based on a high speed centrifugal motion of the grinding chamber, very high power intensity is delivered to the grinding process. Most significantly, a high acceleration field, 50 times stronger than gravity is produced, creating very high power input per unit of mill volume, and exceptionally fast particle breakage rates, typically 50 - 100 times greater than those in conventional tumbling mills. A mill developing such forces has significant implications to comminution technology and practice.

Jan 1, 1999

By Jan Tegtmeier, Horst Gerhardt

INTRODUCTION Under certain circumstances the closure of former mines which are located above a certain flood level can result in problems such as the emanation of detrimental substances after having completed filling and reclamation operations. This especially applies to uranium mines in which the radiation dose could far exceed the dose of natural background radiation. By means of an example of the uranium mining in Germany in the following it will be demonstrated how to cope with this problem. On the basis of comparative investigations in various vein deposits and using ventilation scheme calculations proposals for the optimization of the necessary forced ventilation can be submitted. REPORT ON SITUATION In the period 1946 - 1989 the former Soviet-German joint- stock company "Wismut" developed into the biggest European uranium producer with a total output of about 220.000 t of uranium. A major mineraldeposit district was the deposit of Schlemaf Alberoda in the Saxon Ore Mountains, in which 80.000 t of uranium were produced. Thus it is among the biggest uranium de- posits of the world, from which various other metals were at- tracted for many centuries. The exploitation of the Schlemal Alberoda deposit involved steep veins in regions near the surface as well as depths of 1.800 m. Until 1991 a total excavation space of 40 million m3, which is flooded at present, was produced. With the average increase in the water level of 80 cm per week the final flood level is expected to be reached in the year 2003. The shaft 373 at present still being used for ventilation will be no longer available since the second quarter of 1998 after flooding the -540 m level because it is not connected with the excavation system near the surface. As a study shows, a radiation dose far above the natural back- ground radiation has to be expected for the town of Schlema due to the extensive mining activities near the surface and due to the subsequent displacement with missing depression fo the main mine ventilating fan. An uncontrolled air flow containing radon leaves the open mine excavation due to the effect of the natural ventilating pressure and emanation caused by the barometric pressure drop with atmospheric pressure fluctuations. This mine air with its high-level radioactive equilibrium results in a high radiation dose in buildings (see Figure l). After having switched off the main ventilating fan in order to investigate the effect of the missing depression the increase in radon concentrations amounted up to 700% in various buildings of Schlema. This was partially due to the inversion state of the weather at that time. The high radon concentration has detrimental effects on the health of the population and of the miners working on the further reclamation in regions above the flood level. ANALYSIS OF THE RADON EMANATION RATE EXPECTED Considering the composition of the radon inflow from the mine workings it becomes evident that 80 % of the radon inflow originates from abandoned excavations and only 20 %from open ventilated mine excavations. This fact has to be taken into account for the ventilation after having reached the final state of flooding. After completing ventilation the radiation dose on the surface is mainly due to the radon emanation from excavations close to the surface. Investigations of the Wismut GmbH showed the in- crease in the specific radon emanation rate by a factor of 100 for abandoned excavations as compared to new drivings. One reason is the larger specific surface of abandoned galleries caused by displacements due to mining activities as well as by fall of hanging. Furthermore the radon can enter the gallery through joints, which have subsequently opened by convergences. All these effects result in a larger free surface available for radon diffusion. The large number of drivings in the deposit sections near the surface and the fact that the highest uranium contents are found near the surface as well as the high fracturing are further reasons for higher emanation rates. Considering these facts it can be expected that the radon inflow of 10.000 kBq/s, which refers to an open mine excavation of about 1.4 million m3, represents a minimum. Only by increasing the specific surface, for which a numerical value has still to be determined, this value will increase with certainty. An extensive radon emanation from the residual excavation, which cannot be flooded, can only be prevented by maintaining the ventilation system. The low pressure produced by the fan in the mine openings prevents the emanation of air containing radon due to the effect of the natural ventilating pressure. Without the controlled withdrawal of the radon the population as well as the miners working on the further reclamation in areas above the flood level would be endangered. Therefore the follow-

Jan 1, 1996

By Keenan. Albert M

The challenge of mining coal seams having a pitch of 30 degrees is one not frequently found in the United States, due primarily to the scarcity of such deposits. However, in the Thompson Creek District in Pitkin, Colorado, such a challenge exists to produce high quality medium volatile coking coal, and development of a longwall system is underway. The deposits under consideration are those of the Anschutz Corporation Inc. of Denver, Colorado, which are not in a virgin state. The properties were originally mined by the Colorado Fuel and Iron Corporation from 1894-1907, and by the Thompson Creek Coal and Coke Corp. from 1953-1966. Approximately five and one half million tons of coal have been mined by the above companies, attesting to its quality. The cessation of operations in both instances was occasioned by economics. Both companies employed a room and pillar system of mining, but being denied the use of high capacity mining and loading machinery because of the excessive pitch of the coal seam. This resulted in an unfavorable productivity expressed as output per man-shift, and thus the high cost of production occasioned by hand loading and semi-mechanization dictated cessation of operations. The specific location of these deposits are in Pitkin County,

Jan 1, 1971

By SAHENDRA SINGH, SANJIT KUMAR PAL, DHARMITA HORO

This study was carried out in Ichadih to map the sulfide/gold mineralization using combined electrical resistivity tomography (ERT) and self-potential (SP) methods. No geophysical analysis has been carried out to delineate such ore deposits in the area. Thus, the study provides a different approach for approximate location and extension of the quartz reef associated with sulfide/gold mineralization. It also provides the elementary idea for further detailed subsurface investigation in terms of geological and geophysical approach. 

By L. M. Lenahan, J. D. Sheets

INTRODUCTION The Raleigh-Durham International Airport (RDU) in North Carolina is the fourth largest airport in the southeast region of the United States. The Raleigh-Durham Airport Authority is currently underway with planning, designing and constructing are placement Passenger Terminal as part of the Major Capital Improvements Program at Raleigh Durham International Airport. The Terminal C Expansion and Renovation Project will replace the existing Terminal C structure with a new processor building and concourse. The project is separated into several contracts. The early stage contracts are constructing a west side storm water management facility, relocating taxiways, installing new drainage systems, installing new aircraft apron pavement, Demolition, the Central Energy Plant and Early Foundations. The later projects are the Terminal Building, Passenger Boarding Bridges, Information Technology Systems and Integration, Furniture, Furnishings & Equipment and Specialty Millwork. The Terminal Building will be constructed in two phases. Phase 1 constructs the north half of the new terminal. Airline operations will move to the new terminal at the completion of this phase. Phase 2 completes construction of the south processor building. The full build out of the project, subject to funding availability, will replace the remainder of the south concourse. The Program’s primary focus is to replace the existing passenger Terminal C with a new terminal that will provide more passenger gates and larger passenger screening, ticketing and baggage handling facilities. The planning for the New Terminal C Program began in 2002 with construction starting in March, 2003. The continuing growth of passenger airline travel in the Raleigh/Durham metropolitan area requires RDU to expand its facilities to keep up with the present and future growth within the Region. In October of 2002, the RDU Airport Authority selected Parsons Transportation Group as the Program Manager/Construction Manager to help assist in the development of the Terminal C expansion program. RDU Airport Authority selected the Seattle Washington Office of URS Corporation as the Engineer of Record for the West Side Storm Water Management Facilities. The Westside Storm Water Management Facilities Project became one of the early critical path activities of the overall RDUAA Terminal C Expansion Program. The Briar Creek Reservoir had been constructed to accommodate storm water runoff to the west of the Airport. The existing 1.5 m culvert that drained runoff from the airport terminal (area) to the reservoir was insufficient in supporting the additional flows

Jan 1, 2005

By William R. Bond, Jim V. Rouse

Introduction The pressure/vacuum (p/v) lysimeter or soil water sampler has become useful for monitoring vadose zone or unsaturated zone water conditions. The soil water sampler was first introduced around 1961. It was used as a monitoring and research device for studies in agriculture and soil contamination around landfills. Since then, it has been used for many purposes. The use of p/v lysimeters at mining facilities to monitor for solution loss is a relatively new idea. The primary purpose of the lysimeter here is to function as an early warning system. It detects leakage through liners of tailings ponds, heap leach pads, and leachate holding ponds. Their use has proven valuable for collecting baseline data and detecting loss of precious leachate fluid. Different lysimeter designs are capable of vadose moisture sampling from near the surface and down to 90 m (300 ft). They are also capable of sampling soil moisture or saturation plume contaminants from areas not accessible by conventional water well installations. The most common installations are usually simple and cost-effective. In many cases, they can be installed without the use of heavy drilling equipment. A properly placed and installed lysimeter can detect solution leaks in several days or weeks. A conventional perimeter monitor well may take months or years to detect a leak of the same magnitude. A discussion on the general design and installation of p/v lysimeters will give an understanding of its versatility. Three case studies of lysimeter installations at mining sites will be examined in detail. Design, Installation, and Sampling Design The basic design of a p/v lysimeter chamber consists of a porous material through which the soil is drawn into a collection chamber. Access tubes run from the unit to the sample station at the ground surface. Most units currently available range from 25 to 76 mm-diam (1 to 3 in.-diam). The sample collection chamber, or body, can vary from 0.6 to 1.8 m (2 to 6 ft) in length. The body can be constructed of PVC casing or Teflon, depending on the installation desired. The collection chamber functions as a holding reservoir for the collected soil moisture. The intake, or porous material, on the lysimeter is the most complex and vulnerable portion of the unit. The pore size selection varies based on the needs of the installation, type of fluid to be sampled, and type of soil material surrounding the unit. Teflon (PTFE) and porous ceramic are used in fabrication of the porous inlet portion. When using a Teflon material, which is hydrophobic, a larger pore size of 70 µm is needed to overcome surface tension and draw water into the collection chamber. It is typically used at sites involving organic contamination, because of its inert properties. Ceramic material is generally hydrophilic, having less surface tension. Therefore, it has a smaller porosity range to conduct the moisture through the porous medium while under vacuum. Pore sizes may be selected from 0.16 to 6 µm, and can be manufactured for the specific needs of the installation. The final major design component of the p/v lysimeter is the access or sampling tubes. The tubes are usually of 6.3-mm-outside-diam. (0.25-in.-outside-diam). They are made of rigid polyethylene or flexible Tygon with a wall thickness of 1.5 mm (0.06 in.). The con-

Jan 4, 1985

By David F. Becker

Two-dimensional, finite-difference elastic modeling aids in planning an optimum seismic-acquisition scheme to define the extent of subsurface cavities resulting from in situ gasification. To understand the seismic effects of a cavity, two models are compared and contrasted. Model A consists of a low-velocity layer (LVL) in a half space; Model B contains a rectangular water-filled cavity in the LVL. Amplitude differences are the dominant effect on the surface records for each model. Cavity resonance and diffraction effects are more definitive in vertical seismic profiles (VSP's) and in a "snapshot" of the wave field. Interpretation and subtraction of corresponding records for both models shows the need for pre- and post-gasification seismic recording. Also VSP data are more informative than surface records.

Jan 1, 1983

By R. V. Ramani

Control is a vital management function by which operations are brought into compliance with predetermined standards to achieve the goals of an enterprise. Events that are characterized by a low degree of expectation, avoidability, and intent necessarily have a low degree of control. Such events are difficult not only to predict but to control as well. Fortunately, very few industrial situations fall into that category of events. It is an axiom of control technology that in order to control, one must first measure; further to measure, one must know the characteristics of the subject (or environment) upon which the measurement must be made. Finally, if measurements are to be made reliably, the influences that affect the measurement must be known and, if possible, understood. The complete control cycle therefore consists of the following: (1) defining the objective, (2) planning to achieve the objective, (3) putting the plan into practice with appropriate instructions, (4) measuring variables or parameters of interest, (5) transmitting and transforming the measurements to analyze the system's status and to predict the future outcome, (6) comparing these with the defined objective, and (7) determining and taking corrective actions to bring the actual results closer to the objective. The management principle underlying the control cycle is the principle of management by exception. The application of the principle and the frequency with which corrective actions are taken vary according to the purposes of the review and control. For example, the control of a machine operation (e.g., truck on a haul road) may require adjustments and therefore data, analysis, and decisions, in intervals of seconds whereas the review for ore-grade control may take several hours. Reviews, on the other hand, for cost control may be done in intervals of weeks or months. In any case, three specific purposes of the control cycle are: (1) to correct the operation so that it follows the accepted plan closely, (2) to evaluate the operation and predict future outcomes in light of changes in the environment or of more experience, and (3) to review the objectives and modify these to be reasonable and realistic.

Jan 1, 1979

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By Maurice A. Ponti

The D.C. Water and Sewer Authority is implementing the Anacostia River Projects component of its Long-Term CSO Control Plan, including 21 kilometers of 3.7- to 7-meter-diameter CSO near-surface diversion storage/conveyance structures and flood relief, pressurized-face, soft ground tunnels at a maximum depth of 65 meters. This paper describes a project-specific soil grouping system that is primarily based on soil characteristics for tunneling derived from tests including Atterberg limits, grain size, swelling, mineralogy, triaxial, pressure meter, and consolidation, which differentiates the project from past area tunnel projects using descriptive systems based primarily on area geology.

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By V. T. McLemore

"Lindgren (1933) defined a belt of alkaline-igneous rocks associated with large quantities of gold and rare earth elements (REE) that extends from Alaska and British Columbia southward into New Mexico, Texas and eastern Mexico. The North American Cordilleran alkaline-igneous belt since has been exploited for numerous types of mineral deposits. In New Mexico, Mid-Tertiary alkaline to calc-alkaline rocks are found with seven types of deposits in these districts: (1) polymetallic epithermal/mesothermal veins, (2) gold-bearing breccias/quartz veins, (3) Cu-Au, Au and Mo porphyry deposits, (4) skarns and carbonate-hosted deposits, (5) iron skarns and replacement bodies (with some gold), (6) gold placers, and (7) Th-REE (with some U, Nb) epithermal veins. Some of New Mexico’s largest gold and REE deposits are found within this belt. Their origin is not well understood, but a compilation of new data (age dates, isotopic and chemical analyses) allows for a better understanding. The diversity of igneous rocks and associated mineral deposits along this belt suggests that this region is characterized by highly fractionated and differentiated; multiple pulses of magmas and involves both upper mantle and lower crustal sources. Once magmas and metal-rich fluids reached shallow levels, local structures and wall rock compositions determined distribution of and final style of intrusions and resulting mineral deposits. INTRODUCTION Lindgren (1933) was one of the first geologists who noted that a belt of alkaline-igneous rocks extends from Alaska and British Columbia southward into New Mexico, Trans-Pecos Texas, and eastern Mexico (Fig. 1) and that these rocks contain relatively large quantities of gold, fluorine, zirconium, rare earth elements (REE), and other elements. Since then, the North American Cordilleran alkaline-igneous belt has been explored and exploited for numerous types of mineral deposits, especially gold. The North American Cordilleran alkaline belt is a north-south belt of alkaline igneous rocks and crustal thickening, roughly coinciding with the Great Plains physiographic margin with the Basin and Range (Rio Grande rift) and Rocky Mountains physiographic provinces (Mutschler et al., 1985, 1991; Bonham, 1988; Thompson, 1991a; Richards, 1995; McLemore, 1996; Jensen and Barton, 2000; Kelley and Luddington, 2002). Deposits within this belt have produced significant amounts of gold in the United States and Canada and include Cripple Creek, Colorado (702 metric tons of gold production), Black Hills, South Dakota (235 metric tons gold production) and Landsky-Zortman, Montana. In New Mexico, the North American Cordilleran alkaline belt extends from the Sangre de Cristo Mountains near Raton, southward to the Cornudas Mountains, in the northern Trans-Pecos alkaline belt (Fig. 2). The alkaline-igneous related mineral deposits in New Mexico have been referred to as Great Plains Margin (GPM) deposits by North and McLemore (1986, 1988) and McLemore (1996, 2001). Alternative classifications by other workers include Au-Ag-Te veins (Cox and Bagby, 1986; Bliss et al., 1992; Kelley et al., 1998), alkalic-gold or alkaline-igneous related gold deposits (Fulp and Woodward, 1991a; Thompson, 1991a, b; Bonham, 1988; Mutschler et al., 1985, 1991; Richards, 1995), porphyry gold deposits, and the North American Cordilleran belt of alkaline igneous rocks (Woolley, 1987; Mutschler et al., 1991)."

Jan 1, 2015

By Carl C. Martin

The treatment of ores in preparation for fatty acid flotation is characterized by a wide divergence in methods, and attempts to define "common practice", even for the same type of mineral, are usually of little value because of the numerous exceptions. Such factors as desliming, pulp density, pulp temperatures, and reagents for conditioning are successfully employed under conditions representing almost extreme opposites. More precise control of variables is necessary than with sulphydric flotation processes It appears likely that variations result from independent development of a process from the multitude of variables that characterize fatty acid flotation and the ores of non-metallic minerals. Consequently, a symposium is a suitable way of presenting a summary of pretreatment methods for fatty acid flotation processes, together with froth control practices, as they exist today.

Jan 1, 1959

By Felicia F. Peng, Lili Li

The dispersion model of nonideal flow was applied to describe the hydrodynamic state within the flotation column. Residence time distribution (RTD) data of a laboratory flotation column were measured to determine the parameters of the model. The effects of operating variables and column geometry on the Peclet number which reflects the extent of axial dispersion were investigated and a semi-empirical expression of Pe was formulated. The dispersion model was validated for the column flotation of ultrafines coal. Under the conditions of sufficient aeration rate and frother addition, a good agreement between the measured recoveries and predicted data was obtained. The dispersion model with first-order flotation rate process of the flotation column developed in this study is useful in predicting the collection zone recovery of fine coal, and for the flotation column scale-up.

Jan 1, 1995

By W. A. Haley

As far back as 1939 state laws have required reclamation of mined lands. Reclamation has been the topic of many discussions and presentations, especially since the late 1960's. In the past ten years many states have added legislation concerning the reclamation of coal-mined lands. In the near future, it seems certain that some federal regulations will be passed that will set minimum guidelines for the states to regulate. Besides the requirement of returning the land to the approximate original contour, future regulations will more than likely demand replacing topsoil from one to five feet thick. As regulations become more stringent, costs will rise accordingly. Since no one has developed a machine that can do all reclamation work by itself, it is necessary to review in detail the tools available and to select the most economical means.

Jan 1, 1976

By C. McKinnon

Climate change is the central challenge facing the mining industry, wherein producers must simultaneously ramp up production to provide the raw materials for clean technologies while transitioning to carbon neutrality. While transitioning to renewables will take time, mines can start improving energy efficiency while improving productivity today. This paper proposes a novel technology ecosystem that can help. By monitoring mine shovels, loaders, haul truck paths, and conveyor belts, the proposed technology enables particle size measurements throughout the operation, truck and belt volume monitoring, ground engaging tools monitoring, and boulder detection.

Mar 2, 2022