Search Documents

By Mark R. Bowie

Air-fall tuffs have been altered to zeolite via reaction of volcanic glass with local pore solutions at the six localities discussed in this paper. These are in the southern Basin and Range Province of Arizona and New Mexico, and in the Trans-Pecos and Coastal Plain regions of Texas. Zeolitization occurred in either closed- hydrologic, open-hydrologic, or hydrothermal groundwater systems. The tripping Spring Valley (DSV) chabazite in Arizona and the Buckhorn clinoptilolite in New Mexico originated in a late Cenozoic network of closed-hydrologic, lacustrine basins extending from southeast Arizona into southwest New Mexico. At DSV, two potentially commercial chabazite-rich tuffs are interbedded with lacustine mudstone. The main zeolite tuft contains up to 90 percent chabazite. The upper zeolite tuff averages approximately 67 precent chabazite. At the Buckhorn deposit, two clinoptilolite-rich tuffs are interbedded with lacustrine m udstone in the upper part of the Gila Conglomerate. The lower zeolite tuff contains up to 90 percent clinoptilolite. The upper zeolite tuff contains over 60 percent clinoptilolite. The Casa Piedra clinoptilolite is in the Trans-Pecos region of Texas. It formed during the Tertiary in a closed basin containing a playa lake. The Casa Piedra tuff averages about 60 percent clinoptilolite. Air-fall tuffs of the Cuchillo Negro, New Mexico and Tilden, Texas clinoptilolite deposits were zeolitically altered by either percolating ground waters in open-hydrologic systems or locally by ponded, saline, alkaline solutions. Cuchillo Negro tuffs are Tertiary and average approximately 50 percent clinoptilolite. Clinoptilolite-rich tuffs of Ebcene age have been mined from four quarries at the Tilden deposits. Tufts from the Kuykendall and Buck Martin quarries contain approximately 50 to 60 percent clinoptilolite. Low temperature, SiO2 - rich, hydrothermal solutions altered air-fall tuff to clinoptilolite and chabazite in the Foster Canyon area of the Tertiary Cedar Hills and Seldon Hills volcanic-vent zone in southcentral New Mexico. Poster Canyon tuffs contain up to 60 percent zeolite and average 40 to 50 percent clinoptilolite. The dominant mineral in the zeolite tufts at the six deposits studied is generally microcrystalline and either chabazite or clinoptilolite. Lithic fragments, unaltered volcanic glass, other zeolites, quartz, calcite, opal-CT, cristobalite, feldspar, evaporites, clays, and mafic minerals are also constituents of the tufts.

Jan 1, 1987

By Francesco Chiappalone, Franco Gasperin, Fabrizio Fara

This document describes the challenging task of mining through tiebacks using a 21'-8" diameter Tunnel Boring Machine (TBM) as part of the Ship Canal Water Quality Project. The mining operation involves navigating through 17 tie-backs that are evenly spaced at 8-foot intervals, with many intersecting the full face of the cutterhead. Detailed analysis and review of TBM parameters specific to this area have been conducted to ensure operational efficiency and safety. Hyperbaric interventions have been planned and coordinated, encompassing pre-mining preparations, continuous monitoring and adjustments during the mining process, as well as post-mining measures. The document highlights the complexity and importance of strategic planning and execution to successfully overcome the tie-back intersections during the mining operation.

Jun 23, 2024

By F. Ames Smith

Offshore oil and gas production operations have moved from water depths of about 50 feet in 1948 to the present record depth of 340 feet. Although mobile drilling rigs are widely used for exploratory drilling, most development drilling and production operations have been conducted above water from the decks of fixed, bottom-founded platforms. Increasing water depths have caused problems associated with design and construction of these platforms and with laying of pipelines, but not so much with other activities. After a platform is installed, drilling, production, and maintenance operations are similar to those onshore and are relatively unaffected by water depth. Events of 1968 indicate that offshore production may soon extend into much deeper water. These events include leasing of Santa Barbara Channel acreage in water depths over 1500 feet, and the successful drilling of a wildcat well in 1300 feet. Designs have been developed for platforms suitable for installation in water over 600 feet deep, and studies suggest they may be used in some areas to water depths of 800 to 1000 feet. Buoyant towers can probably support above-surface platforms in water 1000 feet and deeper. Although the cost of either of these platforms will be high, once installed they will permit relatively low-cost development drilling and production operations compared with estimates for subsea production systems. In some cases, savings in development drilling costs alone could pay out the platform investment.

Jan 1, 1969

By Joseph C. Rota, Charles E. Ekburg

Introduction The Gold Quarry gold deposit is the largest bulk tonnage epithermal gold deposit in northeastern Nevada to be developed by Newmont Gold Co., formerly known as Carlin Gold Mining Co. Exploration and development of the deposit extended over a period of nearly 50 years before bulk tonnage mining became economically feasible. Proven reserves at Gold Quarry are currently estimated at more than 255 t (8.2 million oz.) of gold, accounting for more than 40% of the total Carlin Trend mineable reserves for 1986. Milling began in late 1985; dump leaching of lower grade ores began in May of 1986. The mill has exceeded the initial design throughput rate of 6.3 kt/d (7000 stpd) and is now processing more than 8 kt/d (9000 stpd). The dump leach facility will process more than 7.3 Mt (8.1 million st) of lower grade ores in 1986. The Gold Quarry ore body is to be developed by an open pit that will eventually be 1830 m (6000 ft) long, 1220 m (4000 ft) wide and 300 m (1000 ft) deep. The mine currently produces 77 kt/d (85,000 stpd) on a 24-hour-a-day, seven-day workweek. Planned pit production will increase to nearly 168 kt/d (185,000 stpd) in 1988. Production equipment currently includes one Demag H-/285, three Komatsu PC-1500 hydraulic shovels, two Cat 992C loaders and 21 90 to 135 t (100 to 150 st) haul trucks. Mining is conducted on 8 m (20 ft) benches within the Paleozoic

Jan 4, 1988

By F. L. Wilke

Truck haulage costs form a major part of the total mining costs in hard rock open pit, mining operations. In order to minimize these costs one has to - determine the optimal truck fleet (type, size and number of trucks), and. simultaneously - determine the optimal organization of running the haulage system, i.e. especially select the optimal dispatching strategy in order to ensure maximal utilization of the trucks, and simultaneously - establish a reliable maintenance and servicing system to guarantee maximal availability.

Jan 1, 1982

By C. D. Wittreich

The University of Idaho, Department of Metallurgical and Mining Engineering, through the Generic Mineral Technology Center, has been engaged in mine design research at the Lucky Friday Mine, Mullan, Idaho. The purpose of the research is to develop and implement the longwall underhand cut-and-fill mining method for conditions at the Mine. The longwall underhand cut-and-fill mining method involves backfilling mined stopes with a compacted tailings-cement mix. After the backfill has been allowed to cure, mining is resumed from underneath. Horizontal stresses in the Lucky Friday Mine are exceptionally high and rock bursts are a common problem. Beus and Chan (1980) have reported a 2:1 horizontal to vertical stress ratio at the mine with a 65-MPa (9,500-psi) maximum horizontal stress at the 1,295-m (4,250-ft) level. Using this mining method under these stress conditions, it is desirable to have a backfill material that has sufficient strength to safely carry the high horizontal wall loads while minimizing external steel supports.

Jan 1, 1987

By Jeffrey Mitsopoulos

King County?s (KC) Brightwater Conveyance Project in Seattle, Washington involves the construction of approximately 21 kilometers (13 miles) of bored tunnel, in three contracts, with four TBM?s which produce large amounts of real-time digital mining data. To facilitate the management of TBM data with a single interface and assist in project Quality Assurance, KC?s Construction Manager (Jacobs Engineering) recommended the use of the software TPC (Tunneling Process Control), developed by Babendererde Engineers GmbH. The paper demonstrates how TPC was used for oversight, analysis and QA on a complex tunneling project and how contemporaneous review and management of data results in a better understanding of TBM performance than can be obtained by retrospective analysis of data.

By J. R. Dillon

Today more than ever, there is an increased demand for higher plant production capacities and efficiencies to offset the increasing costs for labor and materials. Plants involved in processing large volumes of bulk materials are particularly interested in more efficient material handling systems to (1) reduce labor and maintenance costs, (2) improve blending of non-uniform raw material feed to processing facilities, (3) improve blending of finished bulk materials from storage. DragScraper systems are being used effectively for handling a variety of bulk materials in both indoor and outdoor storage. Materials being handled include ores, chemicals, coke, clay, and stone, to name a few. Handling capacities these machines can provide vary from a few tons to over 1500 tons per hour. The basic components of a DragScraper machine consist of a bottomless Crescent scraper, a two or three-drum DragScraper hoist assembly including gas, diesel, or electric power unit, operating cables, guide blocks, and either fixed or mobile head and tail structures. They are presently available in sizes through 15 cubic yards, for operating spans up to 1000 feet.

Jan 1, 1969

By Raymond Sandiford, Kenneth Xu, Taehyun Moon

Tunnel approach structures situated in slow moving earth flows are subjected to significant earth pressures. The authors have developed a system, utilizing collapsible concrete columns, that limits such loading. The system uses an array of collapsible concrete columns in front of the structure to absorb downslope movement and limit-imposed loads. This concept has been modelled using 3D FEM analyses and a rudimental lab test. For implementation, the collapsible columns would be prefabricated in strengths to mimic the soil strength profile. This concept has merit, and analytical results demonstrate that collapsible columns are a viable means to limit loading.

Jun 23, 2024

By Zhongxue Li, Baolu Zhou, Yiqing Zhao

"Rare earth elements (REEs) are a kind of new materials which have excellent optical, electrical and magnetic properties, and they play an important role in the development of high technology and green energy industries. With abundant reserves and a wide range of REE type, rare earth industry has a rapid development in China in recent years. However, environmental issues associated with REE exploitation have severely restricted the sustainable development of rare earth industry in China. At present, literatures on the externalities of REE exploitation are very limited, especially in China. This paper builds an evaluation model based on life cycle evaluation to estimate the external costs of REE exploitation at Bayan Obo. The results show that the external costs for producing one metric tonne of rare earth oxides (REO) in Bayan Obo was CNY 34739 in 2013, the external costs of waste gas, waste water, radioactive substance, REE resource depletion, and land occupation are CNY 14945, 12515, 1400, 3199, and 2680, respectively. Waste gas and water constitute about 79% of the total external costs. The internalization of the external costs would reduce the financial profit of Northern Rare Earth (Group) by 18%. This study has taken into account only those externalities whose market values can be estimated, and therefore the external costs of REE exploitation in Bayan Obo is likely to be underestimated. The results fill the gap in literature and provide further understanding on the external cost of REE exploitation.Introduction / Background Along with increasing concern about environmental pollution problems caused by the usage of fossil fuel and the shortage of fossil energy, a transition has occurred where development has moved toward green and renewable energy sources with less pollutant emissions (Stegen 2015). Rare earth elements (REE) are a group of important raw materials for these trends since they have unique magnetic, electronic and optical properties, and thus make them widely used in making high-performance magnets and energy saving lamps (U.S. DOE 2010). In addition, REE are crucial for manufacturing of widespread high-tech applications in medical, defense and electronic industries. Many countries have made medium-term and long-term plans for the development of their REE industries, and the annual growth rate of global REE demand is expected to increase by 6% by 2020, and reach about 170,000 metric tons of rare earth oxides (REO) by 2020 (Rollat et al 2016)."

Jan 1, 2017

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By S. E. Phillipson

Slickensides cause potentially hazardous ground conditions in underground coal mines. Investigations by MSHA’s Roof Control Division indicate that many slickensides represent bedding plane faults and drag folds that formed during coal bed decollement, a style of faulting that occurs in shale units above coal seams. These slickensides formed in response to regional tectonic compressional stresses, rather than by differential compaction, and are parallel to folds and thrust faults. This paper relates slickensides in the Appalachian, Illinois, and Black Warrior basins to the structural grain of the Appalachian Mountains, provides descriptions of slickensides, and advocates geologic mapping as a predictive method for identifying areas with adverse ground conditions.

Jan 1, 2003

By H. Maleki

In this paper, long-term measurements in five underground mines are presented to demonstrate how these measurements can be applied to stability evaluations and design of underground excavations. These case studies address both the global aspects of strata response to mining activities as well local ground behavior and support loading. The measurements include static (stress and deformation) and geophysical. Case studies quantify pillar behavior, roof-floor deformation patterns, overburden response, and microseismic activities. Large-scale studies quantify the nonuniform nature of overburden deformation and collapse. Local measurements address yield and stable pillar load deformation characteristics, as well as the performance of support systems under combined axial and lateral loads.

Jan 1, 2002

By Alan Dahlstrand

The Jamestown Mine is a 6.3-kt/d (7000-stpd) open-pit gold mining operation located in the central portion of California's historic Mother Lode district. Most early production from the Jamestown area occurred in underground operations from 1906 through 1916. Pit production began at Jamestown in early 1987 and continued until July 1994. Although additional mineral resources existed, they were deemed to be uneconomic. About 23.3 t (750,000 oz) of gold were produced from pit operations, compared to 31 t (100,000 oz) from early underground mining. Recent operations at Jamestown included two open pits, a flotation mill and a flotation tailings facility. Flotation concentrates were produced in Jamestown and shipped to Yerington, NV for cyanide leaching in a carbon-in-pulp (CIP) circuit.

Jan 1, 1995

By T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground-water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is obviously a more realistic simulation of the problem, but the former method is significantly easier to use, Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.15 to 0.60. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1992

By K. N. Han, Q. Xu

The adsorption behavior of gold in ammoniacal solutions on activated carbon was studied. The gold adsorption capacity of the activated carbon and the recovery efficiency were examined. The parameters affecting the adsorption of gold on the activated carbon included temperature, agitation speed, the concentration of cation and anion and the concentration of ammonia. It was found that the maximum gold adsorption was about 10 kg/t of carbon. The recovery of gold by the adsorption, from ammoniacal solutions was found to be dependent upon the initial gold concentration. Under experimental conditions, a gold recovery of 98% was obtained after 120 hrs of adsorption. It was also found that the initial adsorption rate was relatively fast, when compared to the entire adsorption period. The apparent activation energy for the adsorption was determined to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on the activated carbon was controlled by pore diffusion.

Jan 1, 1997

By Ditend Tesh, Mallikarjun Pillalamarry, Nikowa Namate, Harmony K. Musiyarira

Many reports have been written about the issues surrounding small scale miners’ challenges in Namibia; yet little has been done to address these challenges. There has been a fragmented approach to address these challenges. Various government arms and donor organizations have utilized piece meal methods in the past in trying to make improvements on the productivities across the sector, but with no meaningful success. This has led to the design and implementation of inappropriate technologies and support services for the sector. The structures of many of the semi-precious stones mining businesses are informal, with very little royalties received by the government. Miners often work informally or illegally and they fear government interference and they distrust outsiders, resulting in them withholding production information. The presence of small scale miners is quite often associated with major challenges, including poor safety and environmental management standards, the spread of communicable diseases and poor working conditions. The majority of the miners employ uncontrolled extraction techniques which damage the crystals and mineral specimens, resulting in intermediate and final products of low quality along with high wastage at the extraction stage. The vision of the Namibian government is to expand the range and value of semi-precious stones and jewelry products processed within Namibia, while curbing illicit flows of raw stones. This will simultaneously secure maximum benefit for the country. This study investigated the interventions aimed at making the small scale mining sector in Namibia sustainable. A baseline study was conducted to analyze the current situation and characterize the industry, including a SWOT analysis. Information was collected through questionnaires, interviews, consultative meetings, field visits and workshops in order to profile the sector. The baseline study results were used in developing interventions for improving artisanal and small scale mining operations. The main challenges for the Namibian semi-precious sector were identified as: factual information about raw material resources and its beneficiation are insufficient or not available, lack of skills, lack of education and access to finances, rudimentary exploration and mining practices, trading and logistics that are not functioning effectively and inadequate sector governance. One key finding of this study was that Namibia is not benefiting through value addition due partly to illicit flows of the uncut stones and to the fact that lapidary is not much pronounced to a greater extent. The following strategic interventions were identified as key in ensuring the sustainability of the small mining sector in Namibia: conducting geological assessment to identify new deposits and quantify the existing ones, improving exploration and mining practices, investing in education and training, creating an enabling environment and improving the sector governance and strengthening the sector organization and supporting the infrastructure.

Jan 1, 2017

Room-and-pillar mining at White Pine started in 1953 from a sub-outcropping orebody that gently dips to 1000 m depths in a distance of about 6 km. High horizontal stresses were recognized in the mid-1960s which had obvious stability impacts when viewed in combination with the increased overburden stresses. Modifications in conventional room-and-pillar design were introduced through the years on a trial-and-error basis to help overcome stability and resource recovery problems. These modifications were based on pressure arch concepts using pillar yielding and/or pillar recovery, and on mine layout orientation to minimize stress impacts. While some of these modifications were successfully applied in some areas, they failed in others. Through the years, visual observations played a major role in panel design with contributions from stress measurements and analyses. However, the down slide in the copper economy during the 1970s and early 1980s resulted in a loss of interest in the application of these concepts. This paper reviews ground control problems and presents the results of recent stress measurements and computer analyses. They shed light on the importance of using yield pillars and mine layout orientation to control stresses at depth.

Jan 1, 1993

By Norman A. Nadel

Those of us who have directed our efforts toward the construction of tunnels have long maintained that tunnel construction is more closely an art than it is a science. We have spent time underground with hard-bitten, tobacco chewing shift bosses and superintendents who have made seat-of-the-pants decisions at the face which have been based upon their long experience underground coupled with uncanny intuition. The courage and skill of these men in the performance of their art is legendary. Without question, they have constituted the backbone of the tunnel construction industry. But just as John Henry, the steel driving man, despite his stout heart and dedication to his task, was supplanted by the steam drill, I fear that our tunnel stiff, at least as we have known him, will become an endangered if not extinct species. The reason for this is clearly that tunnel construction is slowly but inexorably making the transition from being an art into being a science, and more and more its performance is requiring the services of scientists as opposed to artists. The tunneling art has been undergoing change for many years, and yet until recently the changes have not been basic. We have improved the way we do the same old things. For example, John Henry would be flabbergasted if he saw the rock drills we use today. He would not have engaged in the legendary drilling contest with one of our modern drills, He would have simply conceded defeat.

Jan 1, 1970

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997