Search Documents

By . A. J. Erickson

The Park City District, one of three major mining districts in Utah, is located approximately 20 miles southeast of Salt Lake City on the eastern slope of the Wasatch Mountains. The district has been in near continuous production since 1869. Production has been sustained from exceptionally long bedded replacement ore bodies in the Thaynes, Park City, and Humbug formations and also from several major veins. District production is summarized below. TABLE NO. 1 Park City District, Total Production, 1869 thru 1968 (Source r Various Company Records) [ ]

Jan 1, 1970

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By J. S. Ross

The significance and role of industrial minerals in Canada differ from those in the United States, The smaller Canadian industry has recently become well diversified and self-sufficient in most commodities, However, it depends on exports, principally to the United States, for much of its market, Imports are small, but imports of several basic products manufactured from industrial minerals are large. This nation is a leading world producer of asbestos, gypsum, sulphur, nepheline syenite, titania slag, potash and barite. It has reserves in asbestos for at least 30 years enough potash to supply the current world's needs for 2,000 years and sulphur reserves for 40 years of current world demand, One of the ilmenite deposits contains enough titania to supply the current world demand for at least, 25 years.

Jan 1, 1964

By P. Zhang

Previous studies have shown that separation of clay minerals from non-clay minerals is the key to economic recovery of the phosphate from the waste phosphatic clays (slime) which represent about 20- 300/0 of the phosphate mined. Small hydrocyclones of different sizes (4" and 6") were tested for sizing the slime at +10 microns in order to remove most of the clay minerals. The effect of design variables and operating parameters were evaluated. Multi-stage cycloning and the effect of dispersant were also investigated. Chemical and mineralogical analyses of different size fractions of both the underflow and overflow samples indicated satisfactorily separation efficiency.

Jan 1, 1998

By F. Dingwu

The latest technology and novel equipments in kaolin processing industry in China are described in this paper. Some typical experimental results are presented, which include laboratory-, pilot-or commercial-scale tests. The characteristics of kaolin processing technology are summarized, and the developing trends are indicated.

Jan 1, 1995

By D. Rucker

Flow models are used to predict the extraction efficiency of metals in rock piles. These models typically use hydraulic parameters obtained through column studies, which assume that the material in the column wholly represents the entire pile and the parameters can be upscaled several orders of magnitude for model evaluation. This assumption fails for parameters that are spatially variable or scale dependent. To overcome these issues, measurements made directly on the heap at the appropriate model scale can be made with the electrical resistivity method. The method aims to map the variations in the electrical resistivity, which can be associated with moisture content, degree of fines, metal content, and leachate concentration. We present an example of calibrating the resistivity with borehole measurements of moisture using geostatistics to show how the resistivity method can be used to obtain a spatial moisture distribution. It was shown that cokriging the resistivity and moisture together gives a more reliable distribution.

Jan 1, 2010

By Sam M. Pickering

Most high, purity silica is produced from crystalline quartz-generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found which is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies - Illinois Minerals Co. and Tammsco, Inc. - mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, Illinois. Both companies mine from various locations within a ten mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Company mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, Arkansas.

Jan 1, 1985

By Walter E. Heinrichs

To many, petroleum exploration and successful geophysics , are partly synonomous, This is not because natural petroleum is usually concentrated as a liquid, nor certainly not because oil can be detected directly. The reason is Chat geophysics helps to at least better understand and sometimes, to even explain the essential geology involved. That groundwater is similarly a liquid with all but a few of its basic geologic relationships practically identical to petroleum, seems to have escaped many of those most interested and responsible for complete geo-hydrologic knowledge. The paramount need to use every means at our disposal for maintaining and expanding our crustal resources reserves are generally obvious, However, in view of the rapidly mounting requirements, continual re-emphasis is worthwhile.

Jan 1, 1963

By Otis M. Clarke

The purpose of geochemical research in the Alabama copper belt is to re-evaluate geochemical prospecting methods as related to igneous and metamorphic rocks in a humid climate. It is also a correlation of laboratory research on copper mineral solubility with geochemical anomalies over known mineral deposits. Geochemical prospecting in warm humid climates involves different problems and conditions than geochemical prospecting in semiarid areas. Stems and others (1972) reported soil surveys in a humid tropical environment in Bahia, Brazil, were not effective in outlining areas of copper mineralization. Clarke (1971) reported false anomalies in lateritic soils in Alabama over mafic rocks. Bjorklund (1971) reported biogeochemical sampling in Finland was ineffective in detailed work outlining potential mineralized areas, although it may serve to indicate regional areas of high mineral potential. During this investigation, water, stream sediments, residual soil, and organic matter, mainly twigs, were collected from three known copper-mineralized areas. Samples were selected so as to cross mineralized outcrops and results were correlated with copper stability charts as reported by Silman (1958) and Schmitt (1962). The geochemical research performed in Alabama should be applicable to other humid areas. Geologic, Climatic, and Pedologic Setting The area of investigation is in the southern end of the Appalachian eugosyncline in eastern Alabama. It includes the Hatchet Creek prospect, Pyriton mining district, and Stone Hill copper mine. The copper mineralization is in calcium-rich metasediments that lie along the western flank of a high rank metamorphic belt. All three deposits are in the uplands of the Ashland Plateau section of the Piedmont physiographic province. The Hatchet Creek copper prospect (Clarke, 1963; 1971) consists of three mineralized areas that contain pyrrhotite, pyrite, and chalcopyrite in small crisscrossing veinlets.

Jan 1, 1972

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993

By Michael J. Mujadin

Since the late 60's, planners at American Natural have known that natural gas supplies from traditional sources will be insufficient to maintain a consistently high level of service in the near future. This dwindling of traditional gas reserves will force American Natural and other gas companies to seek new and more exotic sources of supply. In recent years a number of alternative supply sources were considered, including arctic gas, LNG, and SNG based on naptha, LPG and coal feedstocks. Several combinations, all of which included SNG from coal were selected as the most suitable alternative sources of gas supply for American Natural, and thus our company embarked on the formation of a coal gasification project in the early 70's. Work began with the evaluation of available coal supplies in the United States in late 1970. Western North Dakota was selected for several reasons: large contiguous reserves of lignite were available near the surface, similar to German brown coal for which the Lurgi gasification process was originally developed; the conditions for land reclamation in the area are favorable; and the people in the area have a positive attitude toward well ordered development.

Jan 1, 1977

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By A. A. Campoli

The U. S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By K. J. Stanaway

Concentrations of minerals between 3.5 and 5 specific gravity such as ilmenite, rutile and zircon in large accumulations of sand constitute "heavy mineral" placers. Two fundamentally different modes of formation characterize "trap" and "bed" placer variants. Smaller and generally higher grade trap placers form during sediment erosion or reworking. Because of their smaller size, they rarely yield economic heavy mineral deposits. They become economic, either if they contain more valuable "heavies" such as gold, or, if they occur within or near much larger but lower grade bed placers. Bed placers form during sediment accumulation episodes in any environment and lithofacies where mineral supply and fluid dynamics are favorable. Three heavy mineral deposits are discussed to illustrate bed placer geology and how trap placers occur with and relate to them.

Jan 1, 1991

By Sidney A. Suhler

The persistent requirement for methods and equipment capable of detecting hazardous anomalies in advance of underground mining has led to the development by the U.S. Bureau of Mines of a directional radar probe. The probe operates from boreholes drilled from the surface into the underground region to be mined. The engineering model radar was completed in early 1982 and field demonstration tests were performed in May of that year at a selected coal mine. Preliminary in-situ electromagnetic tests were performed at several candidate coal mines to evaluate the radio-frequency characteristics of the coal. A coal mine in New Mexico was selected on the basis of low EM propagation losses in the coal and the presence of an extensive coal seam displacing fault as a radar target. The borehole radar was operated in two vertical boreholes which intersected the coal seam at approximately 25 and 40 feet from the fault interface. Radar reflections from the coal/ rock interface were detected in both tests. Underground tests in a horizontal borehole in the coal were less successful because of interfering reflections. Additional borehole-to-borehole tests were performed with a separate ground penetrating electromagnetic system to obtain radar range calibration data. The coal was found to be bounded by very lossy roof and floor sandstone and shale while propagation through the coal seam was obtained at distances up to 175 feet between test boreholes. Coal seam continuity was indicated by the hole-to-hole experiments through a section of the seam previously thought to be completely cut off by the fault.

Jan 1, 1983

By T. H. Ueng

Solving ventilation networks of natural air splitting is a classical problem in mine ventilation. A common approach to this problem is to formulate it based on Kirchhoff's voltage and current laws and obtain the solution by an iterative technique known as the Hardy Cross method. In this paper, it is shown that the problem can be formulated and analyzed as an unconstrained optimization (minimization) problem. The computational experience with the method of conjugate gradients is also discussed.

Jan 1, 1984

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

By Simon Strong, Tim Brown, Luis Ignacio Sanz Vivanco

"One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the pre-stressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels. An essential part of the tunnel ventilation system, the smoke duct, extends the full length of the 4.6km long twin, two lane tunnels. The vast majority of the tunnels (approx. 4.3km) were constructed using two 12.4m diameter double shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit out challenges. A key component of the civil fit out of the tunnels was constructing the smoke duct in the TBM tunnels which was designed as a precast solution. The slabs which each measure 8.62m long by 2.0m wide by 200mm thick and weigh close to 9 tonne need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100mm. This paper details the events of how the Transcity JV tunnel fit out team, comprising some of Europe and Australia’s leading tunnel construction specialists, drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system to solve this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began."

Jan 1, 2016

Water and wind erosion of toxic zinc and lead smelter waste is one of the most urgent environmental problems to be solved in the Silesia region of Poland. Over 87 x 106 Mg of various mining wastes were disposed of in uncontrolled piles leading to soil, water, and air pollution in highly populated areas. Welz and Doerschel process Pb/Zn smelter wastes were stabilized in the summer of 1994 by application of heavy loads of CaCO3 (30 Mg/ha), CaO (1.5 -15 Mg/ha), and municipal biosolids (150 -300 Mg/ha), followed by seeding with a mixture of acid-and salt-tolerant grass species selected in a pot experiment. Vegetation was successfully established on 85% of the Welz material demonstration plot area (0.5 ha), even though it was initially high in water-soluble Zn, Pb, and Cd ranging from 0.4 to 1311,0.1 to 5.8, and 0.05 to 55 mg/kg, respectively. Standing biomass averaged 3.3 Mg/ha on the stabilized Welz waste zone by the end of the third growing season (1997). The revegetation of much of the Doerschel material area failed initially because of extremely high salinity (16 dS m-1), high content of water soluble metals (Cd in particular), and heavy compaction. The area was capped (15 cm) with waste lime and retreated with bio-solids (300 Mg/ha) in 1995, and standing biomass averaged 2.9 Mg/ha in the fall of 1997. The observed plant response to bio-solids and lime indicates this approach to be an environmentally beneficial technology as compared to the traditional methods utilizing topsoil covers.

Jan 1, 1999

By B. Tolwinski

Long-Term Open Pit Scheduler or L-TOPS is a new software package for evaluating, planning, and design of open pit mines. L-TOPS transforms geological, economic, and technical information about a mineral deposit into a detailed mining schedule that maximizes economic efficiency without neglecting the practical requirements of mining operations. L-TOPS has been customized for integration with Placer Dome Inc.'s existing in-house resource/reserve optimization software to function as a primary tool for property acquisition studies and for the designing of mines for feasibility studies. This pa-per presents an overview of L-TOPS and reports on its application to Placer Pacific's (Placer Dome's Australian affiliate) Mt. Rawdon project.

Jan 1, 1996