Search Documents

By Yi Luo, Jeremy Slagley, Arunkumar Rai, Steve Guffey, Syd S. Peng

Research was conducted to study the characteristics of longwall mining machine noises and to develop engineering controls for the reduction of noise exposure at longwall faces. Time-motion noise dosimeter data was analyzed and compared with existing databases. Experiments were conducted above ground on a stage loader/crusher to explore the potential of using active noise control (noise cancellation) in reducing the noise levels. A 5-7 dBA reduction in recorded stage loader noise was achieved. This paper presents the equipment, procedure and results of the noise surveys, as well as the active noise control experiments.

Jan 1, 2005

By W. J. Schlitt

The development of forced aeration as an approach to enhancing copper sulfide leaching is traced from its earliest development up to present day operations using this technology. Both large-scale field tests and commercial operations are covered. The historical portion is preceded by an introductory discussion of the role of air (oxygen) in sulfide leaching. Sufficient aeration may be achieved via naturally induced convective airflow. However, cases are identified where this is insufficient, leading to retardation of the sulfide leach rate. For these situations, forced aeration may be beneficial. The historical portion of the paper focuses on the major field tests that have been conducted in Montana, Nevada and Utah, along with commercial operations in the United States, Australia, Chile and Peru. The paper concludes with some general comments about the applicability of forced aeration, which are based on the information developed to-date.

Jan 1, 2006

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

By M. P. Valoski

Mine fires and/or explosions continue to occur. While these are unusual events, they comprise emergency situations. Whenever one of these events occurs, the Mine Safety and Health Administration (MSHA) responds with specially trained teams, mine fire experts, sophisticated scientific instrumentation, and trained instrument operators. In order to analyze mine air samples on-site, because time is of the essence, MSHA has a Mobile Gas Laboratory. The laboratory, which is stored near Pittsburgh, is totally self-contained. Sending air samples to a laboratory would take too long. Mine fire experts need the results of the latest analyses as soon as they are finished. The mobile laboratory is housed in the box of a diesel truck. Benches line both sides of the laboratory. Gas chromatographs are mounted on the benches. There is sufficient bench space for multiple bench top gas chromatographs. These instruments and their controllers are shock and vibration isolated to protect them during transit. The mobile laboratory can operate using on board diesel generators or line power. An uninterrupted power supply (UPS) supplies power to the instruments while switching from generator to line power or visa versa. Therefore, analysis of samples can proceed without interruption if a power failure would occur. In the rear of the mobile laboratory are racks that hold compressed gas cylinders. These cylinders contain carrier gas and compressed air. An air compressor is housed under the laboratory to operate the gas chromatograph actuators. Within several hours after arriving at a mine the instruments have stabilized and have been calibrated. The mobile laboratory is ready to begin analyzing air samples. The mobile laboratory has proved itself at many mine fires and explosions since its purchase.

Jan 1, 2009

By Marina Carreiro-Silva, Cátia Cardoso, Bruce Shillito, Lisa Mevenkamp, Alastair Brown, Maria J. Bebianno, Juliette Ravaux, Inês Martins, Nélia C. Mestre, S. Sousa Vânia

Mineral extraction activities in the deep sea will expose the local fauna to potentially toxic compounds. However, very few data are currently available on the complex ecotoxicological risks to deep-sea fauna from the potential release of heavy metals, trace metals and Rare Earth Elements (REEs). Nonetheless, this is key information essential to support the regulation of industrial activities in the deep sea. One of the fundamental issues that the MIDAS project will address consists in exploring the concept of whether the existing toxicity test protocols and limits established in shallow-water species are applicable to deep-sea mining. We will detail the specific challenges to recommending exposure limits within the deep sea and show preliminary results of comparative toxicity tests in the shallow-water and in the deep-sea environment.

Sep 1, 2014

By Robert D. Coyle, David L. Emmons

Introduction The Cove gold-silver deposit is located in Lander County, NV about 50 km (30 miles) southwest of Battle Mountain, NV (Fig. 1). The deposit is in the north-central part of the Fish Creek Mountains within the McCoy mining district. Gold was first discovered in the McCoy district in 1914 by Joseph H. McCoy (Vanderburg, 1939). From 1928 to the early 1930s, minor production occurred from shallow underground workings. Total gold production was less than 311 kg (10,000 oz; Stager, 1977). The district was inactive until the mid-1960s when it was explored by Bear Creek Mining, Summa Corp., Houston Oil and Minerals Corp., Gold Fields, and Tenneco Minerals. Tenneco began a detailed reevaluation of the McCoy deposit in the fall of 1984. Tenneco's decision to place the deposit into production was based on a geological reserve of 8.7 t (280,000 oz) of gold (Kuyper, 1987). Subsequent exploration and development drilling of the McCoy skarn deposit has more than doubled the mineable skarn reserves to 19 t (615,000 oz) of gold. In September 1985, Tenneco began development work on the McCoy gold-skarn deposit. The project is an open-pit, heap leach mine. The first gold was poured in April 1986. Echo Bay Mines acquired Tenneco's precious metals properties in October 1986. The mining operation and district exploration started by Tenneco is continuing under the Echo Bay's ownership. The Cove deposit was discovered in January 1987 and production began in February 1988. The deposit will begin as an open-pit, heap leach operation. It will be converted into an open-pit and underground mine with a 9-kt (10,000-stpd) mill. Geologic setting The Cove gold-silver deposit is situated on the east flank of the Fish Creek Range. Surface elevations range from 1460 to 1680 m (4800 to 5500 ft). The deposit is 1.6 km (1 mile) northeast of the McCoy gold-skarn deposit. The Cove deposit is hosted by the Augusta Sequence of Triassic age. Three formations of the sequence are mineralized at the Cove. In ascending order they are the Favret, Panther Canyon, and Augusta Mountain formations. The Favret formation is a gray, locally silty limestone that is commonly fossiliferous. The base of the formation is not exposed. Exposed and drilled intervals are more than 60 m (200 ft) thick. Conformably overlying the Favret formation is the Panther Canyon formation. This formation is 215 m (700 ft) thick and consists of a siliclastic and carbonate sequence of conglomerate, quartzite (sandstone), mudstone, limestone, and dolomite. It is a distinctly coarsening-upward sequence of rocks. The top of the unit is conglomerate with chert and quartzite clasts up to 150 mm-diam (6 in.-diam). The Augusta Mountain forma-

Jan 8, 1988

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By Richard B. Stein

Section 25 has been assembled to give the geological, mining, or metallurgical engineer an overview of some of the important downstream operations that typically follow mining activities. This subject is obviously too broad and complex to be covered in detail within this Handbook. However, the engineer will be interested to learn about the basic fundamentals, and especially how they might affect the economics of the total project from prospecting and mining through to metals recovery and marketing. In this way, it is hoped that the engineer will have a better overall appreciation for the technical and commercial prospects of a mining and metal-producing project.

Jan 1, 2008

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By M. Gouet-Kaplan, J. A. Finch, S. Gélinas

Methylisobutyl carbinol (MIBC) and methoxy polypropylene glycol (Dowfroth 250) bubble thin films were characterized by composition and thickness determinations, using FT-IR spectroscopy and UV-Visible spectrophotometry, respectively. The infrared investigation indicates that the role of frother molecules in creating bubble thin films is based on their effectiveness in inducing H-bonding reorganization of the surrounding free water molecules into a coherent network. From UV-Visible interference patterns, it is found that MIBC forms films with a measured critical end thickness of less than 160 nm, compared to 612 ± 30 nm for Dowfroth 250. The observed values of the free water layer thickness are comparable at 5.65 ± 0.28 µm for MIBC and 6.75 ± 0.34 µm for Dowfroth 250. A higher stability of an MIBC bubble over a Dowfroth 250 bubble is related to the different polarization and orientation of the molecules sustaining the boundary surface water network. The findings are used to explain the different action and associated froth characteristics of the two common industrial frothing agents.

Jan 1, 2006

By Tom Ireland, Tony Rock

The proposed 1.83km long twin bore A3 Hindhead road tunnel planned for contruction in 2008 is being delivered under a Highways Agency Early Contractor Involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunneling medium is a ‘soft rock’ sandstone for which there was little previous tunneling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240m long portal section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels, and the innovation included in the ‘permanent’ primary lining design.

Jan 1, 2007

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines is completing a Feasibility Study for a new open pit gold mine in north central NV. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing open pit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled, and unscheduled random events during the period under analysis.

Jan 1, 2006

By J. W. Davis

In the last few years major industrial companies have begun to realize the importance of Reliability as an enterprise strategy that, properly implemented, will improve financial performance. Typical results of an effective Enterprise Reliability Strategy include a 20% -50% reduction in maintenance cost accompanied by a 5% - 10%increase in real production capacity, with no capital investment in production equipment. One factor fueling the race to acquire and implement enterprise reliability is the pressure for companies to be increasingly cost-effective and competitive in global markets. In a recent study, Asset Productivity: The Next Wave, the Boston Consulting Group (BCG)stated that, “In order to compete for funds, companies must offer investor returns that are competitive with other opportunities. Alternative investments such as dot-com and others with non-traditional business models have raised the bar.” (APDF version of the study can be downloaded at www.bcg.com). BCG views asset productivity as the most powerful mechanism for increasing shareholder return. The author believes that the most effective way to increase Fixed Asset Productivity is to maximize asset utilization by increasing the Reliability of the Assets and the associated processes. Developing and implementing an ERS requires significant effort and knowledge. Most companies have difficulty finding a sufficient supply of these valuable commodities to implement an ERS Program internally. Many companies also struggle with figuring out how to get started and what direction to proceed.

Jan 1, 2003

By J. Egan

The recovery of gold by ore leaching is influenced by the size of the particles and the chemical environment. Within the experimental error associated to the testing of gold ore, results of a series of leaching tests conducted with natural ores rather than monosized samples confirm that gold dissolution increases with decreasing ore particle size. The tests also indicate that the dissolution of gold in the ore within a size interval is weakly affected by the intensity of the size reduction method.

Feb 27, 2013

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

By Willard C. Lacy

A mining operation begins with prospecting and exploration-stages with long periods of investment and high risk of failure. However, success in exploration ultimately determines survival of the mining industry. Prospecting and exploration may discover evidence of a mineral occurrence and outline its size and character, but ore deposits that support mining are "made" through the collective efforts of project geologists, geophysicists, geochemists, metallurgists, engineers, chemists, lawyers, and even politicians (Joralemon, 1975). Some deposits may go through multiple cycles of rejection and recommendation, discovery and development, decline and abandonment, rediscovery and development, etc., as economic, technological, or political conditions change or geologic understanding is improved. Peters (1987, p. 233) graphically illustrates the normal life cycle of a mine and the position of exploration in the cycle (Fig. 4.0.1). During the past fifty years, mineral exploration has evolved from comparing evidence of mineralization of prospects with that of known deposits to a more quantitative science employing many facets of geochemistry, geophysics, multispectral sensing from space, computer data storage, analysis, modeling, and most importantly, a better understanding of ore genesis. This modem approach to exploration began in the late 1940s and continues to develop. Exploration efforts peaked in the 1960s with emphasis upon the search for porphyry copper deposits, Mississippi Valley lead-zinc deposits, and volcanogenic massive sulfide copper-lead-zinc deposits. It peaked again in the middle and late 1980s with emphasis upon micron-size disseminated gold and epithermal and stratiform precious metal deposits.

Jan 1, 2008

By Jimmy Thompson

The Santa Clara Valley Transportation Authority is designing the Silicon Valley Rapid Transit Project in San Jose, California. The project includes 6.9 km (4.3 miles) of twin-bored tunnels to be constructed through downtown San Jose using two earth pressure balance machines (EPBMs). This paper begins with a project description and update of the project status followed by a description of the relationship between anticipated ground conditions and EPBM requirements. Topics addressed include soil conditioning, abrasion resistance, annulus grouting, face pressure estimation, additional pressure control devices and control measures to limit over-excavation and settlement.

Jan 1, 2008

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By Tim O’Neil

Dressed in black tie and Victorian attire, some 200 people came to Leadville, CO, for a September weekend featuring a National Mining Hall of Fame and Museum (NMHF&M) induction banquet and a scenic mountain train trip to Fremont Pass and the Climax Mine. The 18th annual induction banquet on Sept. 17 began with cocktails and a open house. It was a chance for visitors to tour the National Mining Museum including the new Hennebach Wing, opened in February. The new wing is named in honor of Ralph Hennebach, retired chairman of Asarco. Formerly Leadville Junior High School, the Hennebach Wing encompasses more than1,440 m2 (15,500 sq ft) of floor space in two stories. One prominent feature is a 1923 Wills Sainte Claire touring sedan. Climax Molybdenum donated this first all-molybdenum steel motorcar. Docents were available throughout the museum to give banquet attendees directions and answer questions.

Jan 1, 2005

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.