Search Documents

By J. M. Richardson, A. L. Mular

Metallurgical balances are fundamental to the successful design and operation of concentration and dewatering circuits. With computerized balance techniques gaining prominence in recent years, it is essential that engineers understand the basic principles that underlie the new methods, as well as the various applications for design of new plants and analysis of existing operations. This chapter discusses two important types of metallurgical balance: (1) steady-state design (2) operating data adjustment Application of computerized steady- state design balancing is demonstrated through the example of a typical copper concentrator flowsheet. Operating data adjustment to achieve a consistent balance is demonstrated for a typical concentrator operation.

Jan 1, 1986

By J. Fuller, L. Marsden

Windborne dust from alkaline salt flats and mining-related tailings ponds is especially prone to threaten applicable ambient air quality standards. Sodium carbonate crystals, typically present, weather to an exceedingly fine, non-cohesive dust, causing air quality problems for miles downwind. Recently developed specialized polymers react with alkaline dust to form sturdy, wind-resistant crusts with good longevity. An on-going demonstration project at a major trona facility has developed techniques for cost-effective application of these polymers over large areas of soft tailings or sediments in a wide variety of situations. Recently treated areas on the order of 80 acres show effective suppression of dust.

Jan 1, 2004

By M. Poulton

Backpropagation, learning vector quantization, counterpropagation, functional link, probabilistic, and. self -organizing map are among the most popular neural network classification paradigms. Each paradigm finds a unique set of weights that will map the input pixels into their respective output classes. The usefulness of each network depends on its overall accuracy, ease of use, speed and scaling. The fastest and most accurate networks in this study were the functional link and counterpropagation. These networks, however, do not scale well to large input vectors or large training sets. A better choice is the LVQ network which achieves high accuracy, is fast, requires a minimum number of input parameters and presents fewer scaling problems.

Jan 1, 1992

By D. Wright, J. Samborski

DuPont’s Florida Plant has been mining in northeast Florida and supplying titanium-bearing minerals, zircon and staurolite for over 50years.The site has successfully implemented and “sustained” a land reclamation/habitat enhancement program that goes beyond regulatory requirements and standard industry practices. However, the term sustainability has been used by so many organizations, many with divergent viewpoints, that it is important for a mine to develop its over-all concept and approach to sustainable operation. As a foundation, the outstanding reclamation efforts at DuPont’s mine will be presented followed by a broader look at the overall sustainability strategies and tactics used at the site.

Jan 1, 2004

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By Leon J. Jacobs, Kyle R. Ott

This paper discusses design and construction aspects of the tunnel, shaft and station for the Weehawken Tunnel and Bergen line Avenue Station. The project consists of a 1,269 m (4,156 ft) long existing railroad tunnel, which will be enlarged and equipped with a two-track light rail system. The project also includes construction of a deep underground station, with a large shaft connecting the surface station to the below ground station for access and ventilation purposes. Vibration and noise from blasting is a critical community issue and blasting adjacent to two 230-kV duct banks located in the tunnel invert required special blasting procedures.

Jan 1, 2003

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By H. P. Ehrlinger

The Illinois State Geological Survey added Minerals Processing to its capabilities in 1966. Subsequently, the Minerals Processing Team and several Geologists collectively thought what neither would have thought of separately. The results included a number of projects. discussed here are: 1) The Utilization of the Fines from Kitty Litter as a Bonding Agent for Iron Ore Pellets; 2) Separating Plant Waste from a Commercial Silica Sand Producer into two marketable products, including a closely sized Silica Sand; 3) Marketable Feldspar Sand and Silica Sand from Dune Sands near the Kankakee River; and 4) A Method for Making Metallurgical Grade Fluorspar more desirable as Blast Furnace (Steel) Feed.

Jan 1, 2003

By Joseph M. Hans

INTRODUCTION The decontamination of a uranium mill site is principally an earth moving task. The task can be completed effectively and efficiently by selecting the proper earth moving equipment and using that equipment within its particular constraints for decontamination work. A considerable backlog of experience concerning earth moving equipment selection and use was acquired during the decontamination work conducted at the former Shiprock, New Mexico, uranium mill site. This experience was acquired by trial and error while decontaminating over a wide range of depths and different types of terrain. Many different types of excavation equipment were available to the Shiprock decontamination project because the Navajo Engineering and Construction Authority (NECA) heavy equipment operator's school was doing the decontamination work and a variety of equipment was needed for training. The equipment is described and its general use for decontamination is discussed. Its on-the-job use for decontaminating the Shiprock millsite is presented. [EARTH MOVING/ANCILLARY EQUIPMENT DESCRIPTION AND DECONTAMINATION CONSTRAINTS] Tractor-Scrapers The most commonly used scraper is the bottom-dump type because it is highly mobile and can dig, carry, and spread loads. In this type a tractor is connected with a yoke to a scraper bowl (Figure 1). The bowl is essentially a rigid box that pivots around the rear axle, opening to the front. A hardened steel knife, or bit, is attached to the leading edge of the bowl. When scraping, the bit penetrates and forces the earth overlying the bit edge into the scraper bowl as the scraper moves forward. When the bowl is full, it is closed by lowering a closure or apron against the cutting bit. The load is dumped while moving, by raising the apron and forcing the load from the bowl with a crowd, or ejector. The height of the dumped load is controlled by adjusting the bit height when dumping. Scrapers of this type generally do not have enough power to scrape up loads unassisted. Loading assistance is generally provided by a crawler tractor that pushes from the rear against the scraper's push block. Some scrapers are made self-loading by adding an additional engine for the extra power needed for the load pick up. Another commonly used self-loading scraper uses a loading elevator (Figure 2). The elevator consists of two roller chains carrying crossbars. The elevator is rotated when scraping and the crossbars cut the earth above or in front of the bowl bit, forcing the load into the scraper bowl. No apron is used on elevating scrapers. The load is dumped by partially retracting the bowl floor and pushing with an ejector. Scrapers have some undesirable characteristics when used for decontamination work. One characteristic is that a clearance space exists around the apron when it is in its closed position. Part of the load (especially sandy soils) dribbles through the

Jan 1, 1981

By J.N. Kohmuench

Teeter-bed (i.e., hindered-bed) separators are used throughout the mineral processing industry for both classification and density separation. The high capacity and sizing characteristics of these units make them ideal for feed preparation prior to coarse flotation (+0.100 mm) circuits. Teeter-bed separators are typically easy to control with two basic operating parameters, including fluidization water rate and bed level. However, data show that these two parameters greatly interact with one another. Given this finding, a high-level automatic control scheme was developed and implemented on a full-scale separator. In addition, dialogue with plant operators has led to several simple changes to an already established design that improves operational and maintenance characteristics.

Jan 1, 2010

Teeter-bed (i.e., hindered-bed) separators are used throughout the mineral processing industry for both classification and density separation. The high capacity and sizing characteristics of these units make them ideal for feed preparation prior to coarse flotation (+0.100 mm) circuits. Teeter-bed separators are typically easy to control with two basic operating parameters including fluidization water rate and bed level. However, data show that these two parameters greatly interact with one another. Given this finding, a high-level automatic control scheme was developed and implemented on a full-scale separator. In addition, dialogue with plant operators has led to several simple changes to an already established design that improves operational and maintenance characteristics.

Jan 1, 2010

By Donald C. Strimbeck

The Bureau of Mines, U.S. Department of the Interior, is conducting research and development on a coal-burning gas turbine. This work includes the development of (1) turbine blades resistant to coal ash erosion, (2) equipment to feed coal under pressure to a turbine, (3) an efficient combustion system, and (4) equipment to remove coal ash from the gases that drive the turbine. Initial emphasis is being placed on testing the first turbine ever equipped with blades designed specifically for use with coal as the fuel. Operating tests with this turbine are now in progress. This paper describes the Bureau's coal-burning gas turbine development program and progress on this operating test.

Jan 1, 1964

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By Brendan Demich, Linda L. Chasko, Brendan Macdonald, Timothy J. Orr, Jessie J. Mechling, Cassandra Hoebbel, Jason Navoyski, William Helfrich, Jessica Cohen, Paul E. Schmidt, Jennica L. Bellanca

The National Institute for Occupational Safety and Health (NIOSH) in partnership with the Mine Safety and Health Administration (MSHA) developed VR Mine Rescue Training (VR-MRT). It is a training platform that allows mine rescue team members to explore virtual emergency scenarios collaboratively. Team members use a head-mounted display to visualize and interact together with equipment, hazards, and dynamic ventilation. All player actions are recorded and displayed for debriefing. Researchers at NIOSH demonstrated the training platform at various mine rescue competitions, including the International Mine Rescue Competition, and collected feedback. Participants’ responses were overwhelmingly positive. This paper describes the development of the software platform and the results of the usability surveys and interviews.

Jun 25, 2023

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By G. D. MacDonald

The Grasberg porphyry copper-gold deposit of P.T. Freeport Indonesia, Co. is located in the Jayawijaya Mountains of Irian Jaya, Indonesia approximately six km west northwest of Puncak Jaya, the highest point on the island of New Guinea. Disseminated mineralization is confined to the Grasberg intrusive complex, a multiphase intrusion of dioritic to monzonitic composition which intruded tightly folded carbonate rocks of the Tertiary Faumai and Ainod formations. The high tonnage and grade of the deposit (1 X 109 tonnes at 1.4 % copper and 1. 8 ppm gold) appear to result from a succession of coincident intrusive and mineralizing events about three million years ago. This paper will focus on the history and character of these events.

Jan 1, 1993

By R. Asamoah, K. B. Owusu, G. Abaka-Wood, W. Skinner

The hostile nature of industrial autogenous (AG)/semi-autogenous (SAG) mill operation necessitates the need for robust and reliable online measurements. Mill slurry density is regarded as a critical variable and requires a suitable range for grinding efficiency. In this work, mill acoustic sensing of five different slurry densities (50, 60, 70, 80 and 90 wt.% solids) was investigated using a laboratory-based AG/SAG mill. The results showed that slurry density of 70-80 wt.% solids gave the highest mass of -75μm particles and similar acoustic intensity. The mill acoustical level increased continuously coupled with energy reduction as a function of increasing slurry density, an indication of potential realtime measurement.

Mar 2, 2022

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step-function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step-function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another is-sue is how they compare to peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1997

By M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow the flow of leakage currents into the mine roof and ultimately result in combustion of the local roof material. The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), has devised a passive means to detect overheating insulators on direct current systems. The detector consists of a spring-loaded cartridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can be easily installed over the outer metallic shell of an existing trolley line insulator. If an insulator overheats due to ground leakage currents, the visible streamer alerts mine personnel traveling on the haulageway.

Jan 1, 1998

By Larry L. Snyder

A compact 4.87 m (16 ft) diameter tunnel boring machine (TBM) is capable of boring a 12.2 m (40 ft) radius curve while gripping horizontally, or vertically, as may be required for the excavation of turnouts. The machine's 5.0 m (16.5 ft) length and a patented machine structure allows steering while boring without causing harmful eccentric loads. An extremely stiff thrust system, rigid front and rear grippers, and the torsional stiffness of a front end electric cutterhead drive combine to create superior machine stability and boring efficiency. A 2.2 m (7.2 ft) diameter prototype, complete with a soft ground shield attachment, was used successfully on a tunnel project in Scotland.

Jan 1, 1989