Search Documents

St. Peter sandstone is an arenaceous sheet that covers large area in North America. The interest for St. Peter sandstone has been increasing due to the upward trend for hydrofracturing and the consequent need for fracking sand. This material is possesses very unique mechanical properties. On the one hand, it is brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The underground mines that are working under this condition are lacking the ground control techniques for this particular mining environment. The geotechnical properties of the St. Peter sandstone were examined using uniaxial test, triaxial test, porosity test, flexural strength test. This paper aims to investigate the effect of microstructure on strength properties, utilizing microscopic studies, index test (porosity, size distribution).

Feb 23, 2014

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modeled with conditional simulation, which generates multiple possible realizations of grade that are equally probable (or improbable). M ethods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time-consuming. This paper proposes a simple and efficient modeling approach to incorporating conditional simulation into pit optimization, which would be able to be applied in currently commercially available software. An example for R esolute M ining Ltd.?s Syama gold project in M ali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Jan 1, 2013

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

By Allan Rocas, Aswathy Sivaram, Daniel Cressman, Tatiana Chiesa

The City of Toronto plans to construct a 1,350 mm consolidation sewer along the East Don Roadway (EDR). The project includes installation of approximately 260 meter of 1,350 mm diameter concrete pressure pipe through microtunneling methods. The sewer alignment crosses underneath a busy 5-lane arterial road and then follows the very narrow East Don Roadway road allowance. This paper discusses the significant challenges overcome to design the Don Roadway sewer using slurry microtunneling methods through mixed face conditions below the groundwater table in a congested road allowance. A curved microtunnel was ultimately required to avoid conflicts with existing utilities, condominium tiebacks and a bridge structure.

Jun 13, 2023

By Kate Willa Brown Requist, Eric Lutz, Moe Momayez

As air quality sensor networks become increasingly popular in underground coal mines, it is important to generate paradigms for the application of the collected data. To date, air quality sensing has been primarily used as an early warning system for hazardous air conditions. Using data collected from a network of sensors in a US underground coal mine, we have created multiple visualization methods to show the interactions of carbon monoxide evolution with ventilation airflow. These visualization methods can allow for further analysis of the source of contaminant, as well as better data resolution across the area of concern within the mine. By utilizing univariate spatial interpolations, we present methods for identifying the movement of carbon monoxide at one-minute intervals. The resulting visualizations display the evolution of carbon monoxide concentration across a sizeable study area over a period of 14 minutes.

Jun 25, 2023

By Kadri Dağdelen, Matthew Deutsch, Thys Johnson

Nested pit analysis in open-pit long range mine planning is used to define approximate ultimate pit limits and an initial high-level schedule in the early stages of a project. Modern ultimate pit optimizers can solve for dozens, or even hundreds, of nested pits however often a smaller subset of pits which are evenly spaced with respect to contained tonnage are desired for downstream analysis. In situations where that pushback selection process must be automated, such as when performing sensitivity analysis, or when the best subset of pushbacks is required; an optimization procedure is warranted. This paper describes a dynamic programming algorithm for selecting pushbacks following nested pit analysis, which is performant and addresses a long-standing inconvenience faced by long range open-pit mine planners.

Jun 25, 2023

By A. G. Belova

With the federal climate change legislation in progress, there is a need for demonstration-stage technologies aimed at providing clean energy from coal. Our research aims to experimentally illustrate the feasibility of capturing CO2 on a novel sorbent system from a gaseous stream. The gas is then released resulting in a regenerated sorbent and a pressurized stream of pure CO2 to be used for storage. The proposed sorbent is a ceramic honey-comb structured monolith coated with CaO supported on a high-surface area alumina. CaO is a natural acceptor of CO2 and our design ensures the physical stability and chemical reactivity of CaO over a large number of CO2 capture/release cycles. Furthermore, the use of the monolith ensures a uniform flow through the reactor, minimizes pressure drop across the reactor, and maximizes the surface reactive area. In this paper, we will present the results from a flow-through laboratory-scale reactor that establishes the efficiency of the proposed system to capture CO2. Future applications of the reactor include integration within the new-generation coal gasification power plants, such as IGGC, as means of providing decarbonized electricity.

Jan 1, 2010

By M. K. McCarter

In 1963, a major expansion program at Kennecott's Bingham Canyon mine converted rail operation in the upper portion of the pit to truck haulage. Since that time truck-haulage capacity has increased to about 272 000 Mg (300,000 tons) per day. The majority of this production is waste material which is deposited in monolithic dumps located on the eastern slopes of the Oquirrh Mountains. The largest of these dumps, referred to as Copper Notch and Keystone, measures approximately 1830 m (6000 ft) in length, from 180 to 300 m (600 to 1000 ft) in height, and contains some 430 Tg (470 mil lion tons) of waste. The height, structure, rapid rate of growth, and anticipated leaching suggested the possibility of dump failure. In order to evaluate this possibility, an outside consulting firm was retained in 1966 to investigate the stability of the growing dumps. Their investigation indicated that, other than superficial movement, the waste dumps would be stable under static loading, and that soil distribution was not continuous enough to sustain massive foundation failure. Since this investigation, however, several failure processes have been observed. Crest settlement occurs frequently in response to compaction and over-steepening in the upper portion of the dump surface. Over-steepening results from accumulation of fines near the crest caused by natural segregation. Normally, coarse material, near the base of the dump, exhibits an angle of repose near 0.65 rad (37"). The fine material, however, stands as steep as 0.75 rad (40"). Periodic equilibrium adjustments cause stepwise settlement (Figure 1) of the dump surface and occasional sloughing of the protective berm. Routine surface preparation by dozers and graders and frequent inspections by supervisory personnel have proven adequate in preventing problems associated with this form of crest instability.

Jan 1, 1976

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974

By Sebastian Avalos, Julian M. Ortiz, Willy Kracht

Semi-autogenous grinding mills play a critical role in the processing stage of many mining operations. They are also one of the most intensive energy consumers of the entire process. Current forecasting techniques of energy consumption base their inferences on feeding ore mineralogical features, SAG dimensions, and operational variables. Experts recognize their capabilities to provide adequate guidelines but also their lack of accuracy when real-time forecasting is desired. As an alternative, we propose the use of real-time operational variables (feed tonnage, bearing pressure, and spindle speed) to forecast the upcoming energy consumption via machine learning and deep learning techniques. Several predictive methods were studied: polynomial regression, k-nearest neighbor, support vector machine, multilayer perceptron, long short-term memory, and gated recurrent units. A step-by-step workflow on how to deal with real datasets, and how to find optimum models and final model selection is presented. In particular, recurrent neural networks achieved the best forecasting metrics in the energy consumption prediction task. The workflow has the potential of being extended to any other temporal and multivariate mineral processing datasets.

Jun 16, 2020

By Lawrence K. Nordell

The selection of belt conveyor drive systems (*) is the subject of ongoing investigation. Frequently this choice has been governed by an incomplete perspective on the major considerations. A more comprehensive and objective approach is desirable. This paper presents additional factors which hopefully will broaden this perspective. BACKGROUND Conventional belt conveyors are powered by electric or electro-mechanical drives(*) mounted at the conveyor's head, tail, intermediate return span, or a combination of these (Fig. 1). A list of the drives reviewed is given in Table I. The following are main elements influencing the selection of the drive system: 1) dynamic characteristics, 2) economic factors such as capital cost, plant spares compatibility, reliability, availability, maintainability, and 3) environmental constraints. The principal dynamic characteristics of concern are the reactions of belt forces generated by the drive system during starting of the conveyor. Another attribute for consideration is the application of multiple driven pulleys used to 1) lower the conveyor's belt tension requirements, 2) increase the expected tonnage throughput, allowing for possible drive component failures, and 3) increase the plant spares flexibility related to the drive assembly.

Jan 1, 1977

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous 'C' coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By Werner Wenzel

Methods to increase the gas penetration through sinter layers. In the field of agglomeration, sintering has gained importance, specially in Europe; in Best-Europe this trend will continue till the year 1980, since it is quite probable that in the blast furnace burdens with 50-60 sinter, 10-20 % pellets and 20-25 % ore lumps will be employed. In order to meet this demand for sinter, new sinter bands with reaction areas between 300-400 m2 will be constructed. Chemical and physical phenomena during the Suction-Draught-sinter process. Iron ore sintering is generally considered as a burning process where the material contains 90-95 % ash i.e. non-combustible ingredients. Sintering represents a heterogeneous exothermic reaction in which the chemical phenomena as combustion, calcination, hydration, reduction and oxydation are superposed by physical phenomena. The physical phenomena are devided into material transport and simultaniously occurring heat transport processes. The velocity of these combined physico-chemical reactions i.e. the change in the reaction site per unit time determine the efficiency of the sinter process. The gas permeability as an important criterion of heat transport during the Suction-Draught sinter process.

Jan 1, 1971

By Shosei Serata

Salt cavities have been proven to be a suitable structure for underground storage of various matters in gas, liquid or solid form. Since the technique of underground storage was developed mainly through field experiences in solution mining, a wider use of solution cavities for storage of gaseous and solid matters requires evaluation of three basic rock mechanics problems; cavity instability, boundary rock failure and surface subsidence. Cavity instability is due to the non-linear long-term creep properties of the surrounding ground media which are sensitive to cavity pressure changes associated with the storage. The cavity boundary rock failure is caused by the loss of effective confining pressure to the boundary rock media in the process of storage of gaseous and solid matters. Surface subsidence is the final outcome of the stress envelope originated around a cavity, eventually reaching the ground surface. The rock mechanics processes of instability, failure and surface subsidence are explained by using various field examples in salt domes and bedded formations. Methods of solving the problems are discussed including stress relief, stress control and computer optimization of design.

Jan 1, 1973

By D. E. Ranta, William B. Ryan, Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1992

By Angelus S. C. Owili-Eger

Although the foundation of a unified treatment of fluid flow in variably saturated porous media was established more than seventy years ago, no serious attempt was made to develop it until the early 1970's. Ever since, a number of unsaturated-saturated numerical models have been reported in the literature. However, none of these models have treated multidimensional, multiphase flow in deforming media, parts of which may undergo extensive secondary fracturing. A situation such as this is not uncommon in coal mining operations in which the longwall method of extraction is employed. The present model has been structured to handle such physical systems. This paper presents the mathematical formulation, the numerical algorithm, and a further validation and evaluation of the modified model. The model treats a multiphase flow in a three- dimensional regime and handles mining excavations of complex and changing configurations.

Jan 1, 1980

By Oscar Cabello, Luis Mendieta, Maribel Guzman

Mineral flotation processes generate large volumes of tailings, which must be disposed of efficiently and safely. In addition to dry stack disposal, the possibility of reusing these tailings as aggregates in shotcrete is an interesting alternative. Tailings samples from a mining operation in southern Peru were characterized by granulometric analysis, X-ray diffraction and Scanning Electron Microscopy. Concrete samples were obtained with different tailings formulations. The samples were subsequently subjected to geomechanical testing. The results showed that replacing 20% to 30% of the tailings with aggregates in shotcrete production achieved compressive strengths exceeding 30 MPa after 28 days of curing, with an energy absorption capacity of 500 joules. Results show that this shotcrete can be used in the support stage of the mining cycle in underground mining.

Feb 22, 2026

By Robert L. Marovelli

Organizational development that attempts to simultaneously deal both with training and with job design parameters as they relate to mine health and safety, productivity, and quality of life is one of several areas of research that the Bureau of Mines is pursuing. The Bureau sees potential in this particular effort for reducing accidents and injuries, improving worker satisfaction and health, and increasing productivity.

Jan 1, 1981

By D. Tao

Reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In this process, quartz is often floated with ether amines (R?(OCH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of quartz does not work well if a certain amount of slime is present in the ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the efficiency of iron ore flotation by the use of a new type of depressant for clay and iron minerals, Georgia Pacific (GP) clay binder. The GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It also helps depress hematite flotation due to its unique chelating action on iron ions. The results from this study show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing iron recovery to 78.15%, while the concentrate grade remained stable at 67.08%. Keywords: Georgia Pacific clay binder, Iron ore flotation, Flotation efficiency

Jan 1, 2010

By P. R. Taylor

The ability to process complex precious metal sulfide concentrates containing antimony and arsenic in an economic and environmentally safe manner is an important problem facing the mining industry in the United States. Preliminary experiments have been performed to evaluate the possibility of treating a complex sulfide concentrate to recover antimony and precious metals while fixing the arsenic and sulfur as calcium arsenate and calcium sulfate. The process involves: • the oxidation of the antimony and arsenic minerals in the presence of soda ash (to collect the sulfur dioxide and to keep the antimony and arsenic from forming volatile compounds), •the selective leaching of the arsenic from the roast calcine with a heated caustic solution, •the precipitation of the arsenic and sulfate with calcium hydroxide and/or calcium chloride, •the reduction of the residual antimony (collecting the precious metals), •fuming of the metal to form a marketable antimony oxide, and •crucible reduction of the residue to obtain a gold and silver dore. Batch experiments, using synthetic concentrates of stibnite and arsenopyrite, were performed to evaluate the first stage of this process. Variables studied included mixture weight fractions, temperature, gas flow rate, oxygen partial pressure, and time. All of the off gas dust and sulfur containing gases were collected and analyzed. The roast solid residues were subjected to arsenic leach tests, and the leach solutions were subjected to arsenic and sulfate precipitation tests. Introduction The ability to treat a precious metal ore containing appreciable amounts of antimony and arsenic is dependent upon the characteristics of the ore. For some ores, selective flotation can be used to separate the antimony and arsenic minerals, which are then treated separately. Unfortunately, many ores are not treatable in this way, and the concentrates obtained may contain appreciable contamination (which limits the ability to make acceptable grade antimony products). If we consider the added value of the precious metals in the concentrate, then it is worthwhile to evaluate the potential for new methods to treat these types of concentrates. In addition, the environmental difficulties associated with arsenic disposal must be taken into account in any proposed process. If there is appreciable arsenic present, then it must be either recovered as a marketable product or placed in an insoluble form. The problem addressed in this research program has become increasingly important as the precious metals mining industry is encountering more ores of this type. A large deposit of this type exists in Idaho where the antimony occurs primarily as stibnite, with minor amounts of kermesite and tetrahedrite (Cooper, 1951). The gold appears in association with arsenopyrite with minor amounts of other arsenic minerals. Flotation has been used to obtain an antimony concentrate. The concentrate, however, is contaminated with appreciable amounts of arsenic and also contains precious metals. If the ore or concentrate contains appreciable amounts of base metals, then the recovery process becomes much more difficult. There are a number of other known deposits of this type in Alaska, Canada, Montana and elsewhere. The objective of this research program was to develop a fundamental understanding of the oxidation and leaching chemistry of the arsenic and antimony minerals so that technology may be developed to treat these ores in an economic and environmentally safe manner. Wendt (1949) and Koster and Royer (1940) discussed the possibilities of oxidative roasting of stibnite concentrates containing arsenic. Wendt describes a process used at a smelter in Czechoslovakia (in the 1930s) where roasting was carried out in rotary furnaces at 723° K (500° C). Most of the arsenic was removed as fume, as well as 25% of the antimony. No sulfur dioxide containment was described. The oxide fume from the furnace went to a heated caustic water leach, where the arsenic was preferentially dissolved and then precipitated with calcium chloride as calcium arsenate following solid-liquid separation. The antimony oxide was sold, and the solid oxide discharge from the rotary furnace was sent to a blast furnace where the antimony metal, containing the precious metals, was recovered. The metal was fumed to obtain antimony oxide, and the precious metals were left in the residue and collected with copper. The copper

Jan 1, 1994