Search Documents

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By James Whitlock, Michael Robert Wilcox

The volume of recently published material in praise of various refractory gold ore treatment methods is impressive. The authors are unfailingly bright, focused and thorough, and as each paper concludes, the reader is tempted to abandon other methods and embrace this truly better way. But there are many "better ways," many different ores, many different environmental requirements and many differ­ent economic circumstances. As we approach each set of cir­cumstances, it would be useful to have an objective way of comparing various methods in order to identify the most promising approaches. This discussion attempts to provide that.

Jan 1, 1991

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

Jan 1, 1997

By Regina N. Tempel, Laurie S. Balistrieri, Lisa L. Stillings, Maggy F. Lengke

The Dexter pit lake, within the Tuscarora volcanic field in Elko County, Nevada, formed after closure of the Dexter mine. Mineralogy at the Dexter mine is related to widespread feldspar, silica, and chlorite alteration. Major mineralogy includes quartz, alkali feldspar, albite, phlogopite-biotite, hornblende, iron-titanium oxide, chlorite, kaolinite, smectite, illite, and sericite, with lesser amounts of calcite, zircon, apatite, and rutile. Trace element geochemistry is characterized by high levels of As, Ba. Cr, Cu, V, Zn, B, Zr, Li, and U. Detailed mineralogy and geochemistry are required for geochemical models to accurately predict trace element concentrations in pit lake waters.

Jan 1, 2000

By T. Vandergrift, J. Sturgill, W. Gerhard, J. Carrick

As surface minable coal is depleted, many operators look to high-wall mining to extend reserve life. Recent advances in highwall mining equipment have greatly improved productivity, clean coal recovery, and attainable penetration beneath the highwall. Somewhat lagging have been systematic design approaches for ensuring web pillar and overall highwall stability. This paper presents an overview of the design, planning, and field performance of a multiple-seam highwall mining application in southwest Wyoming. The safety and efficiency obtained to date is attributable to the careful geotechnical and operational planning described herein. Field confirmation of performance and suggestions for improvement are also discussed.

Jan 1, 2004

By P. E. Sarquis, R. Lenzo

The concentration of barite by gravity separation generates substantial quantities of fine particle wastes, and it is estimated that =40% of the contained barite is lost to these waste streams. In this study, froth flotation was examined as a potential method for the recovery of fine-barite particles. The study included the use of kinetic equations to estimate the variables affecting flotation, batch-scale rougher flotation tests to study the flotation variables and an examination of alternatives for the cleaning of the rougher concentrate. Results indicated that a concentrate grade of 96.5% could be achieved with a recovery of 77.5%. Although barite flotation from industrial wastes is more difficult than direct barite flotation, the process has considerable economic potential.

Jan 1, 1996

By M. Karmis

According to international projections and future energy scenarios, coal will continue to be a prominent fuel for the next 25 years. In fact, in many regions around the world, coal is expected to dominate the electricity sector until the year 2030. At the same time, with instability and volatility of oil prices, coal is also positioned as an alternative feed stock for conversion into liquid fuels. Energy economists maintain that coal liquefaction is viable at crude oil prices of $35 or more per barrel. Depending on technology and coal composition, 1 ton of coal can produce 1 to 4 barrels of oil. Increased coal production and the expanded utilization of coal also raise environmental concerns regarding greenhouse gases and the problem of handling CO2. Carbon sequestration research, currently conducted in many parts of the world, has demonstrated considerable potential for C-storage in unminable coal seams. Such geologic storage, when possible, can also be integrated into an enhanced coal bed methane recovery process Can coal fuel power plants and industrial facilities, provide diesel and other liquids and, at the same, also be used as a medium for permanently storing CO2? This presentation will provide a global perspective on these questions and stress on the need to reconsider, or even redefine, coal as the fuel for the future.

Jan 1, 2006

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By E. V. Bowman

This paper is intended to deal with the material handling aspects of fine coal cleaning as applied to a recently built plaint in: southern West Virginia. This plant is processing 160 tons per hour of 1/4" x.0 coal on a two shift basis. Past experience with this very friable low volatile metallurgical coal indicated that its plastometer readings, varied directly with the size and length of time elapsing between mining' and ultimate consumption. Due to the mines location with, respect to its consumers, little could be done to decrease the time element. Studies indicated that the plastometer readings are considerably less in the minus 60 mesh range than that experienced in the plus 60 mesh sizes. Therefore, handling the coal in such a manner as to have the least amount of degradation became extremely important.

Jan 1, 1961

By E. Sarris

Tailings dams are large-scale earth-fill embankments that are designed to contain mining wastes from ore dressing plants. Most commonly tailings dams are constructed in stages in order to keep up with the increasing volume of mine tailings. Staged construction using various methods (like up-stream, down-stream, and centerline) is generally considered as a very effective way to construct this kind of embankments. The present study is devoted to the investigation of the behavior and the stability of these geostructures under static conditions. In order to accomplish this task, elaborate two-dimensional numerical models are examined, utilizing the geotechnical finite-element code PLAXIS. Numerical analyses are conducted for all three types of tailings dams in order to obtain the potential modes of failure, while the corresponding factors of safety are determined by the shear strength reduction technique.

Jan 1, 2005

By J. P. Morgan

The Vesta Preparation Plant of the Jones & Laughlin Steel Corporation is located on the Monongahela River, eight miles south of Brownsville, Pennsylvania. This plant is capable of cleaning 2400 NT/hr of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables. handle the -1/4" fraction of the raw coal feed. Cleaned -coal goes to boot classifiers where the +48 mesh material settles and is removed by bucket elevators. This 1/4 x 48 mesh material is then sent to centrifugal driers for dewatering. As designed, the minus 48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and dewatered by filtration. The-products of the heavy media circuit, the launder-table-boot-drier circuit and the cyclone-thickener-filter circuit are combined to constitute the shipped metallurgical coal. This Vesta-Shannopin mix is combined at J&L's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke.

Jan 1, 1962

By M. K. Gangal, E. D. Dainty

The paper describes the capabilities of a micro-computer-based real time data acquisition system for monitoring and control of mine environments. Applications of such a system for monitoring the ventilation and air quality of a mine is outlined. The paper discusses the results of running a monitoring system with various environmental sensors in a simulated mine environment. The sensors used in this study are: carbon monoxide (CO), carbon dioxide (C02), nitric oxide (NO), nitrogen dioxide (NO2), sulphur dioxide (SO2 ), methane (CH4 ), air flow, absolute pressure, temperature and relative humidity. A performance evaluation of the monitoring system and sensors is presented.

Jan 1, 1987

By Howard J. Haselhuhn

"The effectiveness of reagent adsorption onto hematite ore particle surfaces is critical during beneficiation to promote effective selective flocculation and dispersion and increase iron oxide recovery. The relationship between aqueous calcium in the process water and the effectiveness of common iron ore dispersants has never before been studied. The nature of common dispersants was studied in the presence and absence of calcium in the process water. The settling behavior of hematite-rich iron ore at pH 11 was assessed in the presence of calcium and inorganic dispersants: sodium silicate, sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP) and organic dispersant ethylenediamenetetraacetic acid (EDTA). It was found that inorganic dispersants are ineffective at a pH of 11 without activating the surface sites of the ore particles with calcium. Organic dispersants, however, were found to be effective with and without surface site activation.IntroductionThe United States produced 54 million metric tons of concentrated iron ore in 2011 (Jorgenson, 2013). Over 8 Mt were produced using a process known as selective flocculation and dispersion (CCI, 2011). The grade of this ore is slowly depleting, making it imperative that processing efficiency improves. To increase processing efficiency, a complete understanding of the effects of chemical reagents in the process must be acquired. This process relies heavily on dispersants to disperse iron oxides from gangue minerals in settling processes. The mechanism that these dispersants use to disperse the ore and its relationship to calcium in the process water has never been studied. The following extended abstract summarizes the relationship between aqueous calcium in process water and the effectiveness of common iron ore dispersants at dispersing hydrated hematite ore. These tests were carried out at a pH of 11, as this is a typical pH used to ensure dispersion in selective flocculation and dispersion processes."

Jan 1, 2015

By P. Kawahata

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on-site facilities depending on ore type and grade. Processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off-site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and complexity of the operation, there are unique challenges in optimizing life-of-mine production scheduling. This paper describes those challenges and methods developed to take advantage of different scheduling software to effectively compensate each other and result in reasonable guidance. This paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Jun 1, 2013

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

4.1 INTRODUCTION There have been numerous methods developed for predicting the final subsidence and final displacement profiles (Voight and Pariseau, 1970; Brauner, 1973a; Kratzsch, 1983). But for discus- sion purposes, they can be classified into six categories: theoretical, profile function, influence function, graphical, physical, and numerical modeling. The theoretical method employs mainly continuum mechanics theories and attempts to explain the mechanisms that lead to sur- face subsidence. Many models using nearly all kinds of material behavior have been developed. These include elastic (Salmon, 1963; Berry, 1964), plastic (Pariseau, 1968), viscoelastic (Iman, 1965), and elastoplastic (Dahl, 1969). The Profile Function Method is essentially a method of curve-fitting against the measured subsidence profiles in a particular mine or region. There are more than 20 profile functions developed empirically for nearly all major coalfields in the world. These include, to name just a few representative ones: Hungary (Martos, 1958), Japan (Hiramatsu and Oka, 1968), Russia (Avershin, 1947), United Kingdom (Wardell, 1965), and USA (Peng and Chen, 1981; Karmis et al., 1984). The NCB's graphical method in the subsidence Engineers' Handbook (1975) also belongs to the profile function method. The influence function method was first proposed by Bals (1931/1932). It was further developed in various periods and stages by Knothe (1957), Liu and Liao (1965), Brauner (1973a) and Marr (1975). This method is now widely used in various parts of the world. The physical models include sand (Litwiniszyn, 1959; Pariseau and Dahl, 1968) and gelatin (King and Whetton, 1958; Khair et al., 1986). They are used mainly to study the parameters that control subsidence behavior. The most popular numerical method is the finite element technique. It can simulate nearly every conceivable material behavior, inhomogeneity, bedding planes, anisotropy, and various boundary conditions. This versatility is absolutely necessary considering the ever-changing geologic and mining conditions encountered. In the following sections, only those methods that have been applied to US coalfields will be discussed. Furthermore, the methods for prediction of several key parameters such as maximum subsidence, maximum possible subsidence, and maximum displacement are discussed first, because they are the key parameters to be used in the profile function, influence function, and graphical methods.

Jan 1, 1992

By R. Bouzaiene

In the paper presented by F.W. Brackebusch on the “Basics of paste backfill systems,” paste fill was presented as a backfill process that offers many advantages over other alternatives such as hydraulic fill and rockfill. It was observed, however, that the mechanics of paste-fill transportation in pipelines is not fully understood and that the success of its implementation in practice depends on the precise control of the proportions of fines, aggregates and water in the mixture. The author emphasized the necessity for laboratory and full-scale testing to determine the suitability of a material to be used as paste fill. Although experimental testing is definitely an important operation in the design of a reliable paste fill, advances in the understanding of the fundamental laws that govern paste flow in pipelines are equally relevant. Ideally, the results of such efforts would provide predictive models for the rheology of the paste and the corresponding pumping-energy requirements. In an attempt to achieve this objective, an ongoing research program has been active at McGill University’s Department of Mining and Metallurgical Engineering.

Jan 1, 1995

By D. J. Kennedy, A. W. Stokes, W. G. Klinowski

Sulphur hexafluoride (SF6) has become an accepted standard in the field of mine ventilation tracer gas studies. It has a wide variety of uses for defining mine ventilation flows that cannot be adequately described using conventional instruments such as anemometers and smoke tubes. The Cape Breton Coal Research Laboratory (CBCRL), Energy, Mines and Resources Canada, has been using SF for the past 4 years and has developed numerous release and sampling systems to increase its versatility. The CBCRL has also completed a successful field trial of an automated rapid sequential SF6 analyzer (which gives a pseudo real-time readout) that can be used underground. In doing this work, the authors recognised the potential of being able to use more than one tracer gas simultaneously in an underground study. Two alternative tracer gases (Freon-13B1 and Freon-12) have already been used by CBCRL in some of their underground work. These gases can be measured by gas chromatography utilising an electron capture detector in a similar manner to SF6. A description of these gases, the methods for 6' their handling, release and sampling are given in this paper together with a brief outline of the analytical system used to measure them. Their suitability to mining applications is compared with SF6. A study in which these three gases were used together is discussed and the results and conclusions given. Some of the additional uses for multiple tracer gases to assist the mine ventilation engineer in resolving problems and improving his day-to-day monitoring are discussed. Finally, a brief analysis of developments which can be expected in the near future is outlined.

Jan 1, 1987

By Gary Jobson

The Mt Todd Gold mine is situated near Katherine in the Northern Territory of Australia. Commissioning of an 8 Mtpa processing facility incorporating a four stage crushing circuit, ball mills, flotation, concentrate regrinding, high rate thickening and CIL processing was commenced during late 1996. A 4.5 M tonne /annum crushing and heap leach facility was commissioned during late 1994, and was subsequently upgraded to a nominal 6 M tonne / annum circuit during 1995. Processing equipment used included primary gyratory, secondary cone and tertiary Barmac VSI crushers. Some of the features of that crushing circuit and heap leach facility were presented at the Randol Perth 95 conference by myself. The location is described as sub tropical with average climatic conditions including 1100 millimetres annual rainfall, predominantly during the December. to March wet season, and 3000 millimetres evaporation and maximum temperatures ranging from around 26 to 46 °C. The main gold occurrence at the Mt Todd site is the Batman deposit, with current published Reserves of some 60 Mt@ 1.20 g Au / tonne ( 0.0425 oz Au / ton ). The primary ore from the Batman deposit is an extremely competent greywacke and is very hard at an average Bond Ball Mill Work Index of26.5 kWhrs/ tonne. Other indicators include a Bond Impact Crush Work Index of 20 kWhrs I tonne, an Abrasion Index of 0.15 and Ultimate Compressive Strength values of 100 - 200 MPa. The main gold occurrence is very finely disseminated free gold (at an average grain size of around 5 micron) within a combination of quartz and mixed sulphide. This gold bearing component is confined to largely parallel veins ranging from 0.5 to 25mm wide within a greywacke matrix. Although the gold is essentially non­refractory, there is a strong recovery versus grindsize relationship due mainly to the liberation characteristics and the relatively low permeability of the host greywacke rock.

Jan 1, 1997

By S. K. Kawatra, S. J. Ripke

During iron ore pellet production, bentonite clay is used as a binder. Typical pellet plants spend from $3 million to $5 million annually for the clay. If bentonite dosages could be reduced by using it more efficiently, a significant cost savings would result. If the binding mechanisms can be completely understood, procedures can be developed to use bentonite more efficiently. Classical bentonite bonding theory is based on the behavior of bentonite at low percent solids and high mixing shear rates. Under these conditions, bentonite was understood to expand, disperse into platelets, and dry into a bonding "film" or "gel." However, these are not the conditions that exist during pelletization, which is carried out at high percent solids and relatively low shear rates. In this paper SEM imaging was used to identify and explain the bonding mechanisms of bentonite on the surface of magnetite concentrate. It was determined that bentonite would form a fibrous network under the proper conditions and that the formation of these fibers corresponded with an increase in the bonding of particles by the bentonite.

Jan 1, 2000

By Todd R. Taubert, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) pioneered the development of disposable filters for reducing diesel particulate emissions from permissible mining machines. The USBM is now evaluating filter media that can withstand the high exhaust temperatures on nonpermissible machines. The goal of the evaluation is to find an inexpensive medium that can be cleaned or disposed of after use, and will reduce particulate emissions by 50 % or more. This report summarizes the results from screening tests of a lava rock and woven fiberglass filter media. The lava rock media exhibited low collection efficiencies, but with very low increases in exhaust back pressure. Preliminary results indicate a collection efficiency exceeding 80 % for the woven fiber media. Testing of both media is continuing.

Jan 1, 1995