Search Documents

By William S. Hallager

Banded ironstone and associated fine-grained carbonaceous sediments near Jardine, Montana, are enriched in gold, arsenic, and tungsten. The mineralized sediments lie within a thick sequence of quartz-mica schists cut by a 2.6 b.y, granite. Surface, underground, and drill hole mapping are used to construct structure contour maps of individual ironstone lenses. Each lens is then unfolded by triangulation of minimum surface path distances between drill hole penetration points. Major and minor element abundances in composite ironstone samples are interrelated through R-mode factor analysis. Results indicate five significant element groupings thought to reflect coarse detrital, fine detrital, sulfide-rich chemical, iron-rich chemical, and epiclastic ultramafic sediment. Ultramafic factor scores are highest in a previously undefined rock type rich in cummingtonite, biotite, and chlorite; lacking in quartz; and closely associated with at least one ore horizon. Detrital dilution of ironstone, calculated from chromium and nickel content, drops off significantly as ore-bearing ironstone is approached. This observation may indicate that centers of gold precipitation have protected themselves, either topographically or by rapid deposition, from detrital contamination. Gold mineralization correlates most strongly with the sulfide- rich factor. Gold may have been introduced through hotspring activity as a bisulfide complex.

Jan 1, 2013

By Charles E. Mauk

In 1970, recognizing the great need for an economical, high capacity chemical oxidation process for wastewater treatment, Houston Research began a fundamental study of the available technology, Included was waste characterization; oxidation chemistry for molecular oxygen, ozone and catalyst initiators; kinetics of reaction; gas-liquid contacting methods; and optimization of staged reactors for mixed wastes. Although ozone is the most powerful oxidizer available, the literature contains contradictory reports of its speed and effectiveness. It is now felt to be most likely that many of these early investigations were limited by the ineffectual transfer of ozone from the gas phase into the liquid, and so the investigators were really observing the effects of mass transfer and erroneously trying to interpret the results as if they were chemical reaction data. HR's work considered the cost and effectiveness of gas-liquid contacting in a packed tower, gas sparged contactor, ejector with hold-up tank, and a completely mixed, sparged contactor. The sparged, mixed contactor was found to be most effective and least expensive, and a later investigation settled on the reactor configuration shown in Figure 1 because of its effectiveness of mass transfer and because it lends itself to direct scale-up techniques using laboratory data to design larger reactors.

Jan 1, 1975

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL

The steepness of an openpit mine’s slopes has a substantial influence on the mine’s financial return. This paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross section within each rock layer: that is, the profile inclination across each layer tends to be constant. Here, instead, a new geotechnical software, OptimalSlope, is used to determine optimal pitwall profiles of depth-varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and factor of safety (FoS).

By Thomas V. Falkie

Of the various critics of federal energy and minerals policy we are hearing these days--and they are legion--few make their points more vividly than our fellow SME member and eloquent spokesman for the mineral industry. Mr. Eugene Guccione. In a moment of comparative mellowness. Mr. Guccione recently characterized Washington's time-honored legislative and bureaucratic machinery as a case of "...scientific illiterates asking the incompetents to do the unnecessary." I hope the prevailing industry view of government is not quite that harsh, and yet one cannot deny that government intervention is indeed pressing in on the mineral industry with increasing force. What is happening today in Washington and in state capitols will have enormous impact--both short and long term--on the future of coal and mineral production in the United States. Symptoms of this trend are everywhere. In the first place, there is a sentiment, widely held and still spreading, that the government must become involved-- that no matter what the problem, the solution lies in more government intervention. Free enterprise versus statist, reflex reaction organizations. When it cones to regulation in the resource field, there is too often a tendency to start out by assuming guilt on the part of the mineral industry. This can lead to laws governing mineral recovery that are more punitive than constructive...laws drawn up with little research into the scientific or economic considerations involved.

Jan 1, 1975

By D. Castillo

The effectiveness of a flotation column is due principally to the addition of wash water to the froth phase. The wash water flow rate can be significant, especially so for systems yielding a high weight recovery of fine solids, e.g. zinc sulfide flotation. Therefore, it is critical to recognize and assess the impact of the water addition upon upstream separation stages. This paper examines column flotation circuit configurations using data from a portable 2 t/day pilot plant. The objective is to provide an improved basis for column design, either as a retrofit or as part of a new circuit.

Jan 1, 1990

By K. C. Corin, B. McFadzean, J. G. Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene and plagioclase feldspar which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals and reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilize the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. In summary due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible. Chromite recoveries can be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. INTRODUCTION The Bushveld Complex located in the north of South Africa contains the world’s largest deposit of Platinum Group Minerals (PGMs) (1). The so-called upper Critical Zone of the Complex hosts the largest concentration of platinum group elements (PGEs) in the world. The Zone hosts the Upper Group Chromitite No.2 (UG2) reef and Merensky Reef as well as the Platreef mineralization of the northern limb of the Bushveld Complex. The Merensky pegmatoid Zone contains the base metal sulphide grains and associated PGMs. Of particular importance to the topic of this paper is the occurrence in these reefs of various gangue minerals. The Merensky Reef consists predominantly of orthopyroxene (~60%), plagioclase feldspar (~20%), pyroxene (~15%), phlogopite (5%) and occasional olivine. Secondary minerals such as talc, serpentine, chlorite and magnetite have widespread occurrence. Of these, talc is the only mineral to show significant natural floatability (2,3). Although present in small amounts talc is closely associated with pyroxene and imparts significant floatablity to the high concentrations of pyroxene present in these ores (4). The base metal sulphides consist predominantly of pyrrohtite (~40%), pentlandite (~30%) and chalcopyrite (~15%). The major platinum group minerals are cooperite (PtS), braggite [(Pt,Pd)NiS], sperrylite (PtAs2) and PGE alloys. The UG2 consists predominantly of chromite (between 60 – 90% by volume) with lesser silicate minerals (5 – 30% pyroxene and 1 – 10% plagioclase). Other minerals present in minor concentrations, can include silicates, oxides and base metal sulphides. Total PGE varies by locality but on average range between 4 and 7 g/t. The PGMs present in the UG2 Reef are highly variable, but generally the UG2 is characterised by PGE sulphides such as laurite (RuS2), cooperite (PtS) and braggite [(Pt,Pd)NiS. The base metal sulphides consist predominantly of chalcopyrite, pentlandite and pyrrhotite. The Platreef is located in the northern limb of the Bushveld Complex. This reef consists of a complex assemblage of rock types, with pyroxenites, serpentinites and calc-silicates being the most abundant. Base metal mineralization and platinum group element (PGE) concentrations are found to be highly irregular, both in value as well as in distribution. The predominant platinum group minerals (PGM) in the mined area of the Platreef are the PGE tellurides, alloys, arsenides and sulphides. T

Jan 1, 2019

By E. J. Wade

My subject is gold price forecasting and monitoring as an important aspect of gold marketing. While I 'm specifically addressing gold, it is understandable that many other commodities could be readily substituted. Gold marketing must be studied as three distinct processes, and it is my intention to cover each of these processes in turn. First I?ll cover the process of gold price monitoring and forecasting in some detail. In order to select a method, or combination of methods, to be used to sell gold a determination of the future price profile is essential. The profitability of the sales effort will be determined, to a large extent, by how accurately the future price behavior of the gold market has been forecast.

Jan 1, 1985

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By R. Wisniewski, S. Schafrik

Every underground coal mine in the United States must deploy and operate a wireless communication and electronic tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. This paper assumes that the tracking system uses the communication system to perform its operation. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 24 hours, and the requirements in the MINER Act for the tracking systems to be “functional, reliable and calculated to be serviceable” and the communications systems “redundancy.” These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using tools that are available to and commonly used by the reliability, maintainability and availability community.

Jan 1, 2014

By Steve J. Czehura

The Butte quartz monzonite is the host rock for early porphyry copper style mineralization and subsequent mesothermal-epithermal, enargite-gold style veining that transects the district. The east-west Anaconda system veins sustained mining for over a century. They include the Emma, Anaconda-Original, Syndicate, Badger-State and Alice-Rainbow veins, each with strike lengths of more than 3,660-m (12,000-ft) and vertical continuity in excess of 1,370-m (4,500-ft) with mining widths from 1.5- to 15-m (5- to 50-ft). These characteristics are unique to Butte. The incredible dimensions and tenor of these veins have yet to be surpassed and Butte is still touted as being the “Richest Hill on Earth.” The Anaconda Company was formed in 1895 to develop underground copper reserves in the district. It eventually consolidated all operations under one company. Production from underground mining continued through the mid-1970s. Openpit mining in the Berkeley pit began in 1955 with the extraction of supergene ores, along with the remnants of deeper horsetail zones inaccessible to the underground mines.

Jan 1, 2006

By John H. Raymer

The accuracy of inflow estimates depends largely on how well permeability is characterized. Permeability is best evaluated as a statistical distribution. For the Chattahoochee Tunnel, this distribution was obtained with a large number of packer tests performed in 50 boreholes along the alignment. The distribution of packer-test data may not accurately reflect permeability, however, due to the limits of the test method and the luck of the field investigation. These discrepancies may be overcome by using log-normal plots of the data to develop a permeability model that will be use din lieu of the data to calculate inflow.

Jan 1, 2001

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

By J. Castaneda, J. Schmidt

"INTRODUCTION Chino is an open-pit copper mining complex faced with intricate material routing requirements. Historically, this was challenging at the mine, in part because the shovel dig plan, haul plan, and dump plan were prepared completely separately. The mine now uses an integrated workflow for faster evaluation of schedules, which facilitates preparing balanced cutoff grade-to-equipment requirements, supports better mineral production, and improves schedule viability, while considering operational implications. Located in the state of New Mexico, Chino is one of nine Freeport-McMoRan mining operations in North America. This presentation discusses the benefits of implementing an integrated approach to tactical mine planning, and shares practical examples that were learned as Chino implemented an integrated tactical planning method. This includes improvements in completion time for preparing a schedule, minimal risk from manipulating Excel macros, data integration required to make short-term planning decisions, and better understanding of the mine plan’s effect in relation to the business’s key performance indicators. Ultimately, the integrated approach to tactical mine planning at Chino has led to production forecasts which are more achievable and reduced planning and execution variance. PROJECT OVERVIEW Chino mine is a porphyry copper deposit wholly owned by Freeport-McMoRan, the largest publicly traded copper producer in the world. Chino mine is located in Grant County, New Mexico, a short distance east of Silver City. Ore material mined from the pit today includes oxides, primary sulfides, and secondary sulfides. The mineralized material is sent to a mill, with a rated throughput of 42,000 tons per day, or to ROM leach pads with variable dumping capacities. At Chino, the short-range objective is to maximize total copper pounds sent to the mill, but no fixed cutoff grade accomplishes this for all periods. Instead, 12 different material classifications, including four sulfide classes that can feed either the mill or other destinations, and 38 cutoff bins, are aligned with the needs from operations, leaching, and the concentrator to create a schedule. Cutoffs vary from one week to another to cope with a highly intermittent ore body."

Jan 1, 2018

By Sakshi Hazuria Anderson, Angela Binder, Oscar Jaime Restrepo Baena, Simit Raval, Sandra Nowosad

As the mining industry faces times of change, new challenges arise to ensure raw material supply for the younger and future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net zero requirements for improving long-term operation performance, technological advancements such as automation and digitalization, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields leaving mining engineering as one of the less preferred career options between the younger generations. Nonetheless, it is essential to continue addressing and supplying the skill sets that are suited to the contemporary and future mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, up skilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more. In countries like Australia, where mining plays a crucial role in the economy, the need for curriculum updates is more pressing than ever. As the mining industry evolves with new technologies and sustainable practices, there is a growing demand for a workforce skilled in these modern approaches. Recognizing this necessity, universities such as the University of New South Wales and Curtin University have taken significant steps to revamp their educational programs. By updating their academic offerings, both universities aim to equip graduates with the necessary skills to drive innovation and sustainability in mining, supporting Australia’s development as a leader in this critical sector. Moreover, the selection of topics that drive curricula update and the focus of the research institutions in mining engineering must extend beyond mere technological and technical aspects to include social and ethical dimensions. In this context, the Universidad Nacional de Colombia, in association with the Colorado School of Mines, has introduced the topic of Humanitarian Engineering (HE) in 2020. HE is a socio-technical approach that focuses on developing engineering solutions that promote the sustainable development of communities addressing their basic needs and aiming to improve their quality of life (10, 18). By focusing on sustainable development, community engagement, and equitable resource distribution, HE helps the industry build positive relationships with stakeholders, reduce conflicts, and foster social license to operate. As the mining industry seeks sustainable and socially responsible practices, future engineers require training in this area to understand the broader impacts of their work, fostering a mindset that prioritizes community well-being and environmental stewardship alongside technical proficiency.

Feb 1, 2025

By David M. Parkes

The hydraulic movement of coal is here defined as the movement of all sizes of coal in pipes and open flumes, by gravity and against gravity. It is not restricted to coal which is in slurry form. In other words, it is not crushed to a size in the 8 to 20 mesh size range. The top size could be as high as 12 inches. The dewatering of coal which is transported hydraulically is carried out to restore the coal to a suitable form for further cleaning, or for transportation by other methods. The process involves complete separation of all the coal, wood and rock from the water so that the water can be recycled without undue damage to pumps, pipes and monitors.

Jan 1, 1976

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Underground mining environments bring occupational health and safety issues with some severe dangers such as mine disasters like explosions. During such events, miners might escape using main access openings, or find a safe haven like refuge alternatives (RAs) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is explained depending on the conditions and their abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification, resistance to the explosion, is discussed in particular, and the studies in the literature are examined in terms of structural deformation. The highest deformed zones, the beneficiation of reinforcing steel components such as stiffeners, and the simulation approaches are investigated through this review.

Sep 24, 2022

By Frank Cook

As in other areas of the country, surface coal mine productivity in the Central Coal Province--primarily Illinois, Indiana, and west Kentucky--has declined steadily since 1969 (figure 1). Productivity, as measured in tons of clean coal produced per man-shift, dropped 35 percent during the period 1969-1975. Unwelcome at any time, this phenomenon is particularly untimely now, when increased coal production is a national goal. The U.S. Bureau of Mines has been working with the coal industry to develop new operating methods and equipment to enable increased productivity and improved reclamation performance in surface coal mining. Several projects have involved identification and evaluation of existing overburden handling and reclamation practices, and development of means to improve operational procedures. Some results of one of those projects, as they apply to the Central Coal Province, are summarized in this paper.

Jan 1, 1977

By P. Dhar, H. R. Kota, M. Thornhill

A very high-grade calcite deposit located in northern Norway consists of CaCO3 ore with minor silicate and sulphide impurities. Cationic (Tallow-1,3-diaminopropane, Duomeen T) collector has been used in the purification of calcite by flotation with an aim of achieving calcite concentrate for its use in value-added products in a variety of industries. The feasibility of sulphide flotation from calcite by this cationic collector has been initially judged from Hallimond flotation and zeta potential on pure mineral systems and the results illustrate the removal of sulphide from calcite ore at neutral pH region. The adsorption mechanism of diamine on both the sulphide minerals was found to be the same by zeta potential studies. The variations in zeta potential are in good agreement with the adsorption of diamine molecular and ionic species as a function of pH. FTIR studies also showed the adsorption of diamine species in agreement with the zeta potential and Hallimond flotation results. Furthermore, the removal of sulphide impurities with selective flotation by diamine collector was performed in bench-scale flotation with the calcite ore and the results indeed showed that the calcite concentrate could meet the quality requirements for its use in the paper industry for coating and filler purposes.

By Carrie Smith

This fall, the Society for Mining, Metallurgy & Exploration (SME) will begin a new chapter by welcoming its new executive director and chief executive officer (CEO). Melissa Russell, a successful nonprofit executive with more than 30 years of experience in global association management, officially stepped into the role on Sept. 29, 2025. She succeeds longtime CEO Dave Kanagy, CAE, who is retiring in March 2026 after more than two decades of transformative leadership. “I am honored to begin this new chapter with SME and inspired by the vital role this community plays in shaping our world,” said Russell. “I look forward to listening, learning and working alongside this remarkable group of professionals to advance innovation, champion sustainability and create a brilliant future together.” Russell brings a deep portfolio of leadership experience in technical and industrial associations to SME. Most recently, she served as executive director of the Institute of Electrical and Electronics Engineers (IEEE) Computer Society, the largest of the IEEE’s 39 societies, with more than 50,000 members across 150 countries. During her tenure, she strengthened global engagement, advanced financial sustainability and launched strategic humanitarian initiatives.

Oct 1, 2025

By Harry Perry

Although the markets for coal in the United States have changed rapidly over the last three decades, the uses of coal, namely, to produce heat and power or coke have been left almost unchanged. The coke is used either as a chemical reducing agent alone or as a reducing agent and source of heat. Most of the heat and power markets for coal require no coal processing, although for more than 50 years, many proposals to skim the more valuable substances in coal before burning have been advanced. Thus, the only large tonnage market requiring processing of coal is high-temperature carbonization to make coke. At present, coal requires processing for some small markets, but for future potential large markets, such as gasification, conversion to liquid and gaseous fuels, and conversion to chemicals, coals will require more processing than is now being done.

Jan 1, 1962