Search Documents

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

By David W. Wisecarver

Kennecott Copper Corporation and the U. S. Bureau of Mines cooperated in a full-scale slope stability research project at the Kimbley Pit near Ely, Nevada. The west wall of the Kimbley Pit was mined from an over-all slope angle of 45° to an over-all slope angle of 57° and the pit was deepened nearly 50 feet. Mining was begun February 10, 1966, and completed October 30, 1966. Approximately 2.55 million tons of ore and waste were mined. The project was designed and carried out to learn more about the behavior of a pit wall as its slope angle is steepened and to obtain a possible insight into engineering parameters for use in design of future slopes. Data from this project are presented as obtained from (1) instruments installed in two adits for deformation and displacement measurements, (2) a subsidence network installed on the surface above the steepened wall, (3) pre- and post-mining observations of stress in rock, (4) sonic-velocity measurements, and (5) seismic and microseismic investigations. Changes occurred in measured quantities as the slope was steepened but stopped when mining was completed. Agreement was noted between the measured changes and predicted changes obtained from calculations using the finite element technique. Subsidence surveys and microseismic studies show the steepened pit wall to be stable.

Jan 1, 1968

By G. Roberts, S. S. Klima, W. R. Reed, J. Deluzio, G. Ross, A. Mazzella

The abstract discusses the problem of silicosis among roof bolter operators in coal mines due to respirable quartz dust (RCS) exposure. It presents a study comparing a new wet box collection system to the traditional dry box system. The wet box system uses water to saturate collected material, reducing RCS exposure during cleaning. The study found that the wet box system significantly reduced RCS exposures and quartz content in samples compared to the dry box system.

May 11, 2022

By William F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test methods used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1982

By A. W. Randall

Geological Aspects of Ore Reserve Estimates of Pine Point District Zinc- Lead Deposits, N.W.T. Zinc-lead ores of the Pine Point District, Northwest Territories, Canada are hosted in paleokarst cavities within a Middle Devonian carbonate barrier complex. Of the nearly 100 deposits found, most are irregularly distributed along two main regional stratigraphically controlled trends. The ores, which occur predominantly as open space filling, form deposits most of which average one million tonnes in size with an average grade of 10% combined zinc plus lead. Geological features related to karsting control not only distribution of deposits but also their shape, size and grade. The higher grade ore in these deposits generally occurs in a relatively small core area. Consequently, accuracy of reserve estimation is dependent on drill hole density and understanding of karst geometry. Several case examples will be reviewed to demonstrate the relationship between shape, size and grade of deposit, geological reserves and drill hole density, along with a discussion of geological ore reserve estimation methods.

Jan 1, 1985

By R. A. Metz, William H. Breeding

The remarks that follow are based substantially on experience covering 45 years, 80% of which has been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1-1/2%. The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present. Most of the rich, readily accessible placers were mined by our forefathers. Current opportunities exist: (1) in remote areas where infrastructure has been absent in the past, or development has been prohibited by adverse ownership - political or commercial; (2) in deposits that could not be mined by equipment available to our forefathers; (3) in deposits unidentified by our forefathers; (4) where the-price-of-product/cost ratio is substantially better than in earlier years; or (5) a combination of those factors. When I entered the placer business in the late 1930s, and subsequently, a prevailing opinion believed that glacial deposits should be avoided as irregular in mineral content and composition, and unrewarding to explore and develop; yet an operator has been mining a fluvio-glacial deposit profitably for the past 17 years. Rich buried placer channels, often called paleo-channels were worked in the last century, generally by hand methods, and under conditions that would be unacceptable today. Exploration and mining equipment now available make some of these channels attractive targets. Well-known examples are in California and Australia. The formation of a commercial placer requires a source of valuable minerals. Above primary deposits, there may be eluvial deposits formed by the erosion of gangue minerals and the concentration "in situ" of valuable minerals. Down slope from these deposits are the hillside or colluvial deposits, and below them are the alluvial deposits of redeposited material. Most of the great placer fields of the world are the result of several generations of erosion and deposition. Well-known examples are in California and Colombia. Gold is a very resistant and malleable material, and gold placers may extend for 64 or 80 km (40 or 50 miles) along a river system. Platinum is less malleable, but is very resistant to disintegration. Diamonds are extremely hard, and (especially gem diamonds) may be found over great lengths of a river system. Cassiterite is less resistant to disintegration, and tin placers seldom extend over two miles without resupply from an additional source or sources of mineralizaton. Tungsten minerals are generally more friable, and within a few hundred yards of the source disintegrate to the point that they are uneconomical to recover. Rutile, ilmenite and zircon placers generally result from the weathering of massive deposits, and may be encountered over extensive areas; most are fine grained and durable. What does a geologist or mining engineer look for in placer exploration? The old adage to look for a mine near an existing mine is still valid. You need a source of valuable mineral. Then you require conditions for concentration, which means a satisfactory gradient and/or other conditions that will permit heavy minerals to settle. Nicely riffled gravel, often called a shingling of the bars, is conducive to placer formation. Coarser gravel is logically associated with coarser gold. Excessive clay and/or high stream velocities in narrow channels can carry gold far downstream and distribute it uncommercially over a large area. When material is extremely fine, in situ weathering and concentration become more important. Placers frequently occur distant from lode mines, and one must remember that in a larger watershed the exceptional floods that occur once in a hundred or a thousand years can move great quantities of material long distances. The carrying power of water is said to vary with the fifth or sixth power of its velocity. I am not ready to disagree with Waldemar Lindgren and accept that many commercial placers are substantially enriched by the chemical deposition of gold from solutions; however, I have seen crystalline gold in clayey material quite distant from known sources of primary gold that is dif-

Jan 1, 1992

By John H. White

As production of ground limestone increased our Company found it had an enviromental problem with limestone dust from our hammer mills. With the quarry and processing plant situated within 1 klm of a small township of 5000 people dust collection became essential. Regulations under the Clean Air Act 1972 also had to be complied with. Prior to this any demand for lime flour had been met by the use of a small drier and ball mill. Both expensive to operate. Dust emitting from the mills would amount to over 4000 tonnes per year. The cost savings were obvious. We had a better product which was essentially a by-product. Faced with a surplus of a very useful, but difficult product to handle we considered the possibility of disposing of it on the agricultural market.

Jan 1, 1982

By S. A. K. Forson, Newton A. Amegbey

In order to investigate production decline in Tarkwa Goldfields Ltd., located in a tropical rain forest, amongst other areas, a health survey was conducted with the aim to see 1. The health status of the workers. 2. Which parameters carry the most information about the health situation and which of them can be applied easily during screening programmes. 3. What steps could be taken to improve the situation. In all 249 workers were investigated. A non-invasive method involving taking of body weight and arterial blood pressure was used. All subjects were required to answer a questionaire. Emphasis was placed on the history of malaria and diarrhoea within the last six months. Both management and workers co-operated fully. Another set of 110 workers from a neighbouring tyre factory were also investigated for control. Among the underground workers, the percentage body weight loss during a shift increased with decreasing body weight. Dehydration levels could be as much as 4 to 5% of body weight. This could be attributed to the fact that workers took insufficient or no water during the shift. The health status of the mine workers was generally poor and in our opinion malnutrition combined with malaria severely threatens the health and well-being of the workers. Hypertension is also a problem. An improvement in production is intimately linked with the well-being of the workers.

Jan 1, 1989

By Paul Bartos

Operations at the Sweet Home Mine transformed the mineral specimen industry, not only in the development of new innovative extraction techniques, but also in the fields of sample preparation and marketing. Principally as a result of the activities at the Sweet Home Mine, there is now a better appreciation of minerals and the market they encompass. Individual Sweet Home rhodochrosite specimens have been sold for more than $1 million, with many more in the five- and six-figure dollar range. This article is a review of the Sweet Home operation, with emphasis on its extraction techniques. District history The Sweet Home Mine is located within the Alma mining district in the Mosquito Range of central Colorado, approximately 6 km (3.7 mile) northwest of the town of Alma at the base of the Red Amphitheatre in Buckskin Gulch at an elevation of 3,440 m (11,286 ft). Other nearby mining districts include Climax, Leadville, Breckenridge and London. All are considered part of central portion of the Colorado Mineral Belt (Fig. 1).

Jan 1, 2007

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By Walter R. Curtner

Many, if not most, of today's pollution liability claims are related to events ("occurrences") that happened in the past. This fact creates an opportunity to obtain a large amount of insurance coverage at essentially no cost. Furthermore, in many cases, this insurance coverage is readily available. Scenario #1 For some 15 years, an underground gas tank has had a slow leak. The leak has now been discovered because the gas has contaminated nearby wells. As a result, an expensive $1 million cleanup is required. In addition, a liability suit has been filed for damages due to the contamination of nearby wells. Consequently, legal expenses are being incurred. Are all of these actual and potential costs insured? Obviously, if you have a pollution liability policy in place, the above costs will probably be insured. I say probably because business liability policies are not uniform. But, what if you don't have a pollution liability policy and what if your current general liability policy excludes all pollution liability (as most of them do today)? Under these circumstances, it first appears there is no insurance for this $1 million cleanup and liability suit. But this is probably not the case. You may well have insurance coverage, and you may well have much more insurance coverage than you ever expected. And, the insurance that I'm referring to is already in place. You simply need to find it and learn how to use this insurance - I'm referring to your old policies. In many cases, old liability insurance policies provide coverage for claims made today, because these policies were written on an "occurrence" basis of coverage. In fact, most still are written this way. This means that the insurance policy covers bodily injury or property damage liabilities (as defined in the policy) arising out of' "occurrences" or accidents that happen during the policy period regardless of' when the claim for damages is made. Therefore, for insurance purposes, the key question is: when did the "occurrence" take place? If someone falls and breaks a leg, that is clearly an "occurrence." The broken leg occurrence is, therefore, insured by the liability policy that was in existence at the time of the fall - regardless of when the claim or suit is filed, if ever. However, the answer to this question is seldom an easy one when you are looking at a pollution claim. In our scenario, the tank had a slow leak over 15 years, but property damage was not discovered until now. The question of when the "occurrence" (as defined in the insurance policy) took place has been litigated and continues to be litigated in many courts across the country. But, most often the answer has been that, for insurance purposes, the "occurrence" is the entire period that the tank was leaking (15 years), even though the contamination to the water was not discovered until 1987. This means that the person or company that is insured can potentially use all of its general liability policies (if they are "occurrence" policies, and most were), which were purchased during the 15 years from 1972 until 1987. And, these policies will potentially insure all of the claims and related exposures that arise out of this leaky underground gas tank. Scenario #2 In our first scenario, the claims and expenses were insured by past general liability policies because the claims arose out of events in the past, which, in turn, caused damage. Let's look at another example. In this scenario, Company XYZ has received a request to help clean up a landfill site because 10 years ago, XYZ dumped some toxic substances at the site, which was totally legal at the time. XYZ has not dumped anything at the site since this time. Nevertheless, XYZ is now being required to contribute $2 million to the cleanup of this site. In this scenario, if you had purchased "occurrence" general liability policies 10 years ago, these 1977 policies would (potentially) apply to the current $2 million cleanup claim. And, the reason is that the "occurrence" leading to the 1987 claim took place in 1977.

Jan 10, 1987

By G. B. J. Leon, M. Karmis, C. Newman

"The prediction of surface deformations due to underground mining operations has been a long recognized practice with case studies documented as far back as 1556 in Georgius Agricola's De Re Metallica (Latin for On the Nature of Minerals). There is currently increased public awareness and regulatory scrutiny on the potential impacts of underground longwall and second mining operations, but this time the focus is placed on environmental impacts to overlaying bodies of water such as streams, rivers, wetlands, lakes, etc. (Karmis and Agioutantis, 2015). Community residents and environmental groups, as well as federal and state regulatory agencies, have often cited adverse stream impacts and demanded stronger measures and scrutiny in issuing mining and reclamation permits (Booth, 2006). Mining companies are required to focus on the protection of sensitive bodies of water through the monitoring of stream flow and water quality, management and rehabilitation techniques, as well as the adoption of ""no mining zones,"" which potentially sterilize large portions of minable coal reserves. This paper examines the use of an empirical modeling approach for the protection of surface streams based on evaluation of ground strain magnitudes. Utilizing enhanced features of the Surface Deformation Prediction Software (SDPS), ground movements can be predicted accurately in the vicinity of surface bodies of water. The modeling of ground movements can aid in establishing optimum extraction sequences, while the magnitudes of anticipated subsidence can be used in the evaluation of mitigation plans when undermining surface bodies of water. INTRODUCTION When utilizing high recovery underground mining methods, such as longwall or room-and-pillar mining, the movement and deformation of the overburden propagates toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope, and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidence initiated changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, subsidence induced strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed, ""ruptures,"" upward blocking stream flow or having the stream diverted into the facture zone at the base (Iannacchione, et. al., 2010)"

Jan 1, 2016

By Jean Rainville

Gold was first discovered in the central region of French Guiana in the mid 1860's. Production was based strictly from placer mining of the various rivers in the region. At the moment, a number of companies are actively engaged in hard rock gold exploration, concentrated in the northern and central regions of the country. The Franc-Or/BRGM joint venture in the Sophie-Repentir region of Central French Guiana offers an exceptional opportu­nity for the discovery of one or more million-plus ounce deposits of gold owing to a highly favorable structural setting in Precam­brian greenstones that host several known vein gold occurrences, some of which appear to occur near the border of a potassic granitoid intrusion. At this point in time, based mostly on predecessors' work, mineable reserves could be estimated to be in the 500,000 ounces range over the length of the property. The exploration campaign under way has the objective to delineate probable reserves of at least 2 million ounces that could be mined by open pit mining methods in the area. The program should be completed in the next 18-24 months. In order to efficiently and effectively evaluate this very large property area, all of the necessary camp, mechanical and drilling equipment has been purchased and is being transported to the property. Most of that equipment was purchased in Canada. The first drill target is the Repentir sector because of its access and the amount of detailed work that has been done by BRGM on that concession, but geological evidence suggests that many areas on the property could offer even more potential.

Jan 1, 1995

By A. H. Leuschner, P. J. Kruger, J. Kruger

INTRODUCTION This paper deals with some practical aspects of the use and interpretation of dosimetric methods for assessing the exposure of workers to natural uranium. Consideration must be given not only to the scientific value of the method of dosimetry, but also to the practicality of the method in the particular working environment. It is generally accepted (IAEA, 1976) that uranium does not present a hazard during the mining and extraction processes up to the final concentration stage, that is precipitation as ADU or calcining to the oxide. Further processing (e.g. conversion to oxides, fluorides, etc.) is generally associated with the nuclear industry. It is customary for uranium processing facilities to be managed according to industrial norms rather than according to those applied for the purpose of radiation protection. This is mainly because of the large quantity of material to be processed and the fact that uranium is considered to be of a low radiotoxicity. Although ventilation is used to some extent, provision is not made for the same level of protection as would be required in a radiochemical facility. It is typical in such a plant to find that the process itself may be enclosed and ventilated, but the ventilation is inadequate to cope with an accidental release of material. The working environment is poorly ventilated, sometimes only by natural ventilation, and one frequently finds areas with high airborne dust levels, designated as mandatory respirator areas. Protection of personnel is dependent on personal protective equipment. Radiation protection is not of prime concern and personnel are not specifically trained in this subject. It is in this type of environment that acceptable monitoring procedures and personnel dosimetry must be established. The effectiveness and practical application of the dosimetry must also be judged against this working environment. DOSIMETRIC TECHNIQUES The methods available for assessing personnel exposure, whether it be in terms of chemical or radiological hazard, include urinalysis, faecal analysis and [in vivo] monitoring. Faecal analysis does not present itself easily as a method for routine use. Techniques for [in vivo] monitoring have been developed recently and as expensive instrumentation is required, it is not generally available. That leaves urinalysis as a dosimetric technique for routine use, and it is probably for this reason that urinalysis is still widely used. Guidelines for the interpretation of urinalysis results, as originally provided by Neuman (Neuman, 1950), are still used in practice, even though it has become clear that this method has severe limitations as regards the assessment of the dose as a result of the intake of class W or class Y compounds (Alexander, 1974). Typically a level of 300 µg [U/C] urine can serve as an indicator of an acute exposure (above which chemical damage to the kidneys may occur) and a level of 100 µg [U/C ] urine can serve as an indicator for an investigation. Such levels are determined and are used in conjunction with several factors, such as mode of intake (ingestion or inhalation), solubility of compound (D, W or Y), means of intake (acute or chronic), environmental monitoring results and frequency of urine sampling. Since the ICRP concept for internal radiation limitation changed from that of the critical organ, i.e. the single organ of greatest significance under the circumstances, to that of effective dose equivalent, i.e. account being taken of the total risk due to the exposure of all tissue, the maximum permissible organ burden (MPOB) was replaced as secondary dose limit by the annual limit on intake (ALI) (ICRP, 1977). The ALI values are calculated from the committed dose equivalents of the various organs, and are used to determine organ burdens, which are then used to interpret the dosimetric results. Using the ICRP model (ICRP, 1979), a comprehensive calculation was made by Johnson (Johnson, 1980), giving organ burdens and excretion data in terms of intake for acute and chronic exposures for different categories of uranium compounds. The question arises as to what extent the direct measurement of intake can be utilised as a method of dosimetry. This will require a method of personal intake measurement for each individual worker, with both ingestion and inhalation being taken into account. A measurement of

Jan 1, 1981

By X. Zhu, L. Chen, R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study was to develop a suitable flowsheet to extract rare earth elements (REEs) from coal ash. Only the findings from the first part of this study is being reported at this time. A total of fourteen coal samples of different ranks were examined for REEs concentration. An anthracite coal sample, originating from Pennsylvania having more than 700 ppm (in the coal ash) was selected for the REE extraction tests. The experimental program completed so far included high temperature leaching using nitric acid, followed by the solvent extraction tests. A 4x2x2 experimental design was used to conduct a total of thirty two high temperature leaching tests by varying acid molarity (at 4 levels), solid content (at 2 level) and leaching time (at 2 level). The highest LREE (light REE) recovery of 90% and HREE (heavy REE) recovery of 94% were obtained from the most optimum leaching test condition while maintaining the impurity recovery to the leachate at less than 40%. Solvent extraction experiments were conducted to recover the REE’s from the above leachate solution using a variety of organic extractants including, TBP, Cyanex, D2EHPA and their combinations. D2EHPA was found to be the best extractant during this SX text series providing nearly 99% recovery of REEs. INTRODUCTION The demand for rare earth element and other strategic metals (REM) in the world is rapidly increasing due to their use in a variety of high technology applications. More than 100,000 tons of rare earth oxides (REO) are being used worldwide on an annual basis. However, we have less than 10% of the world reserve of rare earth element (REE) mineral deposits in the US. More than 60% of rare earth oxide (REO) was imported to the US from outside (mostly from China) in the year of 2013. However, China’s institution of export quota has significantly reduced the supply of REMs to the U.S. Hence, new ways of producing REM and/or finding substitutes for those metals for the high-tech applications need to be invented/discovered in a timely manner. Coal Combustion Byproducts (CCBs), which are discarded as waste materials in most cases, are known to contain REEs (in low concentration) that could be extracted using a suitable process flowsheet. This may be a worthwhile route to pursue considering the short supply of REMs and the abundance of coal ash in thousands of ash ponds in the US. On an annual basis, more than 110 million tons of Coal Combustion Byproducts (CCBs) are being produced while satisfying our nation’s need for electricity (ACAA, 2014). However, less than 50% of these CCBs are being successfully used in various applications and the remainder is being dumped as waste materials in the landfills and ash ponds."

Jan 1, 2017

By David E. Nicholas, Steven R. Dismuke, Paul F. Cicchini

The Buick mine, located 195 kilometers (120 miles) southwest of St. Louis in the Viburnum Trend, is owned and operated by Homestake Mining Company. The mine produces lead and zinc ore from a room and pillar mining method at a depth of approximately 335 m (1 100 ft). The Buick orebody typically averages 60 to 120 m (200 to 400 ft) in width with ore thicknesses ranging from 2.4 to 36.6 m (8 to 120 ft). The mine is divided in two; the halves are referred to as the North mine and South mine orebodies. The North mine orebody contains the higher grade ore; however, the developed reserves for the South mine orebody comprise about 60 percent of the total developed reserves for the Buick property. Existing pillars represent one-third of the total developed reserves.

Jan 1, 1986

By M. Gershon

The article is an excellent one, providing a basis for the conduct of the major tasks in underground mine planning and scheduling. I object to only one word. Since that word is featured in the title, it is a strong objection. The word used erroneously is optimization. There is no optimization performed in the article. By definition, an optimization is an approach that yields the best of all possible solutions. We can limit this definition to its narrowest sense, the optimization techniques of operations research such as linear programming, or broaden it to include less sophisticated search procedures that find the best mine plan or schedule. No such claim is made in the article. No optimization of any kind is performed. The major tool used is a simulation, which, in truth, is probably more appropriate for this problem than any optimization. But simulation does not optimize. It only allows for quick evaluation of many options, leading to the selection of the best plan "of those tried," not "of all possible plans." This article, of course, is not the first mining paper to make this error. It seems that the word optimization is used more to impress people than to refer to any act of optimizing. It is used in a way that implies "try to optimize" or "come close to optimize," but not to really do it. It is usually appropriate to quietly ignore this error. But when Dr. Chatterjee, who has done so much good work in true optimization projects and whose work I have come to admire, makes such an error, it is time to publicly dispute it. Having discussed this very point with him in the past, I am sure that he will agree. If he can support this position in his response, perhaps people will start to listen and we can reduce the number of false claims of optimization. This should be easy for him in this case since the approach he used, simulation, is the more appropriate one anyway.

Jan 1, 1987

By Ulises Deveze T.

The coal company Minerales Monclova, S.A. (MIMOSA), the owner of the Mimosa R Line, is a subsidiary company of Altos Hornos de Mexico, S.A., the largest steel plant in Mexico with an annual capacity of 2.5 million metric tons of steel ingots. The raw material's which are used in the steel plant are provided by the following companies: La Perla Minas de Fierro, S.A., iron ore; Cia. Minera de Guadalupe, S.A., Cia. Carbonera La Sauceda, S.A. Cia. Minera La Florida, S.A., and Minerales Monclova, S.A., which provide the coal used for coke, and altogether constitute the industrial group AHMSA. The coal property of Minerales Monclova, S.A. is located in the Sabinas coal area in the northwestern part of the Sabinas basin.

Jan 1, 1974

By Greg Sanders, Michael Gilbert, James G. Shaughnessy

"A new raw water intake from the South Holston River to the Kingsport water treatment plant is under construction. The exploration for the 335 meter long horseshoe shaped tunnel design took advantage of the site topography along the alignment to better define the complex geology consisting of Knox Limestone and Sevier Shale formations separated by a fault zone. To assess the geological conditions and to determine the extent of the fault zone, a 183 meter long horizontal boring and geophysical investigation was performed along a portion of the tunnel’s horizontal alignment. Explorations defined the fault zone width at approximately 5 meters and packer testing along the alignment provided a means of estimating groundwater inflows. As the tunnel excavation advances, comparisons of exploratory data versus encountered conditions will be made. This paper provides details on the geotechnical investigation, lessons learned, and the influence of the geology on the tunnel design. PROJECT OVERVIEW The Kingsport WTP is supplied with raw water via the South Holston River. The City of Kingsport (City) owns and operates the Kingsport Water Treatment Plant (WTP). The existing raw water intake system, consisting of pumps, power supply, raw water piping and appurtenant facilities has been determined to be vulnerable to failure. The original Raw Water Pump Station (RWPS) was constructed in 1928 as part of the original Kingsport WTP project. The 1928 RWPS operated until 1970 when it was replaced by the existing RWPS. This existing system still utilizes the 1928 piping and piping tunnel. Improvements to the RWPS hydraulics and capacity are required to meet the City’s future water treatment needs. The system extracts water from the South Fork of the Holsten River and coveys it via three pressure pipelines to the WTP. The conveyance piping exits the RWPS, ascends approximately 23 m up a near vertical rock outcropping then enters a 120 m long tunnel. Upon exiting the tunnel the piping continues underground to the WTP. The drill and blast tunnel is horseshoe shaped and nominally 3.3 m high by 3.3 m wide. The easternmost 62.3 m of the tunnel is without any type of support. The remainder is lined with concrete. According to the City of Kingsport, the concrete lining was installed in the 1970’s as part of upgrades to the facility. An evaluation of the current facilities concluded that the conveyance piping was in poor condition and required replacement."

Jan 1, 2016

By Alfredo Valdivia, Jesus Schabib, Vojtech Gall, William Cao, Curt Cicileo, Andrew J. Thompson

"The East Side Access Project (ESA) involves the construction of geometrically complex underground structures including a large number of caverns and bifurcations. Initially conceived as dual lined structures with either traditional concrete or shotcrete final linings (SFL), construction economy, advances in concrete placement technology and scheduling among others led to a wide use of what is referred to as freeform or pneumatically applied concrete (PAC) for the construction of tunnel final linings. PAC is a method of applying concrete without using formwork, where a wet mix concrete is pneumatically installed to encase reinforcement to full lining thickness. PAC has been widely adopted at ESA well beyond initial expectations. The paper addresses the design and construction aspects of the PAC method and contrasts it to traditional SFL lining placement. The experience made provides guidance for future PAC and SFL applications. THE EAST SIDE ACCESS PROJECT AND USE OF FREEFORM CONCRETE The Long Island Rail Road (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodates New Jersey Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the New York City Transit (NYCT) Subway System and Metro North Rail Road. The construction includes mining and lining of new tunnels and facilities under Manhattan and Queens. The tunnels run from Queen’s Sunny Side Yard through the existing 63rd St. Tunnel, underneath Manhattan’s Park Avenue until termination at 37th Street. Differing types of tunneling methods and final lining systems are being used depending on the ground conditions, geometry and size of the excavation, site constraints and functional requirements. Mining of the Queens segment of the ESA Project involved soft ground tunneling by pressurized face tunnel boring machines, cut and cover construction, and conventional tunneling. The Manhattan segment of the ESA Project involves mining in hard rock by tunnel boring machines, drill and blast, and road header."

Jan 1, 2016