Search Documents

By F. Breu, R. Fraser, R. Lawrie

Diesel-powered underground mining equipment is generally accepted as the most productive, safest, and most efficient equipment used in underground mining operations. Widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel emissions with particulate traps and filters.

Jan 1, 1988

By St. E. Deák

Mining activities involve excavation from underground to the surface of large quantities of ore (e.g. uranium and its disintegration products) (Dumitrescu, 2002, 2007). Material with limited content of uranium, deemed as sterile or low-radioactive is mainly stored on the surface. These wastes modify the configuration of the disposal areas and affect the quality of the environment and the landscape. This paper presents both analytical and numerical models related to stability assessment of uranium mining waste dumps. It is focused on the calibration procedure of the numerical models, in order to minimize risk error during stability prediction and avoid long term environment pollution.

Jan 1, 2008

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.

Jan 1, 1987

By S. K. Kawatra, T. C. Eisele

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20% if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1992

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991

By W. Z. “Ben” Wu

The investigation provides a method of efficiency evaluation among several kinds of tools employed to cut different types of rocks. A ballistic test stand incorporated with a modified Hopkinson bar was used to simulate a percussive drilling tool. An Apple IIe microcomputer was employed for high speed data acquisition and numerical analysis. A newly developed method for remote monitoring the rock-tool interaction, including contact force, bit penetration and energy transmission,is presented in the paper. Theoretical predictions and experimental results appear in faily good agreement

Jan 1, 1986

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By Joy Sandberg

The 1989 mining industry compensation survey done annually by the Denver-based Mountain States Employers Council shows the "average" or "typical" employee in the mining industry is projected to receive an increase of 3.9% to base pay in 1990, compared to a projection of 4.1 % for 1989. According to MSEC, the actual percentage increase to base pay has continued to decline since 1980. A review of pay increases since 1980 shows the highest average increase was 11%, granted in 1981. Since 1981, there has been a steady deceleration through the decade. While 1989 final figures are not available, 1988 numbers might indicate a reversal of this trend. In 1988, the average employee actual increase was 3.8%. That was 0.7% higher than the 3.1% projection. This may be significant as actual increases have been lower than projections since 1982. Chart A shows the pattern of projected vs. actual percent increases in pay since 1980.

Jan 1, 1990

By D. S. Young

The random variable transformation technique was introduced to make probabilistic structural analysis simple for such structures as slopes, dams, foundations, or retaining walls, where two shear strength parameters are required to analyze their stability by deterministic engineering methods. The Gaussian transformation was performed by using the Hermite orthogonal polynomial function. This transforms the experimental histogram into the standard normal distribution, whose mean is zero with a variance of one. Then, the transformed standard Gaussian variable was used for the bivariate normal probability analysis on the structure. The Gaussian transformation technique and the Hermite polynomial functions were chosen because the bivariate joint normal distribution is well-known and easily available for engineers. The binormal probability analysis was made on the probability region of a certain confidence level by superposing the critical line on the same probability region that divides the region into two zones: stable and unstable zones. The critical line was determined from the back calculation of the deterministic engineering method of the structural design. Finally, the probability of structural failure at a desired confidence level was calculated by simply integrating the volume of the binormal density surface above the unstable zone in the probability region. A simple case of slope analysis is introduced to illustrate this probabilistic approach, and its effectiveness and simplicity is demonstrated.

Jan 1, 1987

By Y. P. Chugh

A novel dry and wet air dust filter concept was conceived and demonstrated successfully at two mines. A steel-wool and a fiberglass filter, suitable for underground use were identified through laboratory testing and demonstrated in the mine. The steel wool filter was operated with and without water sprays while the fiberglass filter was only operated in the dry mode. The dry steel wool filter provided a dust capture of 37% at a negligible pressure drop. When fine misting water sprays were used on the steel wool filter, the dust capture increased to 51% again with a negligible pressure drop. The filter screen also remained clean and no change in air flow characteristics was observed as a function of time. The dry fiberglass filter however did not perform as well achieving only 11% dust capture while introducing a significant resistance to air flow. This technology is seen to have several applications in underground coal mines.

Jan 1, 2009

By J. Keng, S. T. Chen, T. M. Shih

Kwanyin Tunnel is presently the longest (7.7 km) railway tunnel in Taiwan. Due to heavy railway traffic, a pass-by station will be built inside the tunnel to increase the traffic flow. Since the concentration of toxic gases released by the locomotives may reach dangerous levels, a research program was conducted for the purpose of designing a ventilation system which could dilute and/or remove the toxic gases to maintain an acceptable pollutant level. The program consisted of two parts. The first part was field measurement during which the concentrations of pollutants and wind velocities were measured at various points inside the tunnel to acquire basic data regarding ambient air quality, piston effects for the different types of trains, and existing ventilation conditions. Weather data (temperature, humidity, atmospheric pressure, wind direction and velocity) were gathered at many stations, both on the surface and inside the tunnel. The amount of pollutants released by each type of locomotive for various conditions were also measured. The second part of this study involved establishing mathematical models for predicting the air quality of the various proposed ventilation systems. Three different models were used for this work. The first one is a piston effect model which assumes that the gases and air undergo immediate mixing inside the tunnel. The second one is also a piston effect model which assumes that the diffusion ability of the gases is zero. The third one is a conventional ventilation model which was used for natural and mechanical ventilation conditions. From the result of field measurement and mathematical model studies, a ventilation system was chosen with consideration of both ventilation effects and construction costs.

Jan 1, 1987

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

By M. Stefanakis, M. Errington, A. Kontopoulos, J. M. Prevosteau, K. Adam

The Olympias arsenical pyrite concentrate assaying 25 g/t Au, 40% S, 40% Fe and 12% As is highly refractory in nature; an oxidation pretreatment step is required to liberate gold and render it amenable to cyanidation. In the present study mineralogical analysis techniques including Image Analysis, SEM, EPMA, SIMS, Mossbauer, ICP/MS, etc., have been employed in order to investigate the mode of gold occurrence within the Olympias pyrites. Bacterial oxidation was used as a case pretreatment route and bacterially leached products were examined under SEM. The mineralogical observations and the relevant metallurgical and cyanidation test data were combined to establish a correlation between the mineralogical characteristics of the raw and oxidised products and conditions prevailing over the oxidative pretreatment step and the gold liberation achieved.

Jan 1, 1990

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987

By C. J. Bise

Safety training requirements differ from mine to mine due to changes in the demographic characteristics of the workers or changes in job and organizational characteristics. Accordingly, a microcomputer-based procedure has been developed to assist mine trainers is determining if undesired worksite performances result from lack of knowledge or skill, which are trainable categories, or from categories that are considered to be non-trainable (such as equipment limitations or management procedures). A special effort was made to understand the psychology of worker behavior by analyzing worker reactions to various organizational and job characteristics.

Jan 1, 1995

By J. Shibata

Separation of rare earth, especially Nd and Sm, was investigated by batch and column methods with a solvent impregnated resin. The solvent impregnated resin was prepared by impregnation of organo- phosphorous extractant whose trade name was PC-88A into a macro porous resin. The adsorption behavior of rare earth with a solvent impregnated resin in a batch method is the same as that with solvent extraction. In a column method to separate Nd and Sm, the effective separation in both adsorption and elution processes can be attained by setting suitable conditions, such as bed height, flow rate and concentration of eluent. Neodymium which is a lighter rare earth is separated from Sm an adsorption step, while Sm in which is a heavier rare earth is recovered in an elution step. From the integration of breakthrough and elution curves, yield of Nd and Sm is calculated in the condition of 100% purity. It was found from the results of life test of the resin that the solvent impregnated resin can be repeatedly utilized at least 20 times.

Jan 1, 1995

By Robert D. Gibson, E. Donald McKay, Paul B. DuMontelle

Subsidence of the land surface in some parts of Illinois is caused by underground coal mining. The U.S. Bureau of Mines is backfilling abandoned mines at selected sites in southwestern Illinois in an attempt to support failing mine openings. The Illinois State Geological Survey assists the Bureau by developing geologic and engineering information. As part of this investigation, television probes of fifteen injection borings in Belleville augmented conventional methods of study. The television probes of uncased sections of borings revealed several phenomena. Water erosion caused shale beds to slough, which partially filled some borings. Fractures caused by subsidence were identified, and excellent views of underground mine workings provided documentation of the mining method. The condition of mine timber was evaluated. Pack walls supported some openings. Both floor heave and roof fall were observed to be causes of failure in the mines.

Jan 1, 1982

By A. de Ferran

Is the Brazilian gold rush over? Judging from the situation in Brazil over the past few decades, the answer is almost certainly yes. The picture of swarms of Brazilian prospectors or "Garimpeiros" crowding or, more correctly, overcrowding the gold regions of the Amazon jungle using the time-aged empirical approach to gold exploration has finally run its course. There are two fallacies that have lead to a reduction in the discovery of new gold fields in Brazil. The first fallacy is that "Brazil's geology is largely unknown." The extreme depth of weathering and the general lack of understanding of the shield deposits are at the origin of this misconception. The second fallacy is that "Brazilian prospectors (`garimpeiros') are very naive, have very little technical knowledge and can only produce gold at very low recovery rates." This is more of a result of wishful thinking for the purpose of justifying limiting exploration programs than it is a real consideration. In this paper, the author takes a methodical heuristic approach to gold exploration in Brazil and offers this as an alternative to the empirical approach of the garimpeiros.

Jan 1, 1997

By John C. Balla

The Spar Lake deposit is located in northwestern Montana, approximately 27 km (17 miles) south of Troy, MT, under Mt. Vernon. The deposit is a stratiform, stratabound copper-silver deposit occurring in the Revett Formation of the Proterozoic Belt Supergroup. Distribution of known sandstone-type deposits in the Revett Formation is shown in Fig. 1.

Jan 1, 1991