Search Documents

By L. A. Wasselle

The Israel Mining Industries Institute for Research and Development has developed, during recent years, a number of new processes for fertilizer materials. Their phosphoric acid processes, however, are capable of producing an acid of far higher quality than that normally associated with fertilizer grade acid. This paper will discuss two of these processes showing the quality attainable and the capital and operating costs for, U. S. conditions. The Standard IMI Process is based on the acidulation of phosphate rock with hydrochloric acid and involves solvent extraction for the separation of high quality, phosphoric acid from the resulting solution. The IMI Purification Process applies the same solvent extraction technique to the purification of a wet process phosphoric acid from sulfuric acidulated rock. IMI has built and operated a semi-works scale demonstration plant for the standard process. The first commercial plant was started up in; Japan in 1962. This small seven metric ton per day plant is currently producing a furnace quality acid. A larger 50 metric ton per day plant is nearing completion in Brazil. Another 50 metric ton per day plant is under design while a large plant with a capacity in excess of 150 metric ton per day is in the planning stage. Both of the latter facilities are for Israel.

Jan 1, 1966

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By Jue Kou, Lei Yu, Bern Klein, Lusheng Zhou, Chunbao Sun, Genzhuang Li, Reem Roufail, Amit Kumar

Magnetic liners can improve the performance of ball mills by increasing grinding efficiency, extending service life, and reducing maintenance costs. Despite their importance, the fundamental understanding and the quantitative investigation on the effects of the magnetic liners has not been addressed in the literature. This paper addresses this gap by studying charge motion, and how the use of a magnetic liner affects the breakage mechanism of the mill, using discrete element method (DEM) modeling and the Hertz-Mindlin contact model with relative velocity dependent (RVD) rolling friction. Charge motion was modeled under different mill speeds. Compared to conventional steel and rubber liners, the charge motion in the magnetic liner mill was predominantly cascading. Quantitative analysis of the energy dissipation within the mill was conducted to investigate mill breakage. Regardless of speed, over 50% of the total energy dissipation in the magnetic liner mill was in the form of abrasion and attrition. The results highlighted the appeal of magnetic liners in secondary and regrinding application, where abrasion and attrition are considered more efficient in the fine material breakage, and where impact is ideally minimized to reduce mill wear. A number of experiments were conducted to assess the effect of different model parameters on the performance of the magnetic liner mill. The highest abrasion/attrition intensity was observed with high values of the model parameters namely the restitution coefficient, static friction coefficient, and rolling friction coefficient.

By A. J. Hendron, G. Mesri, R. M. Semple

Squeezing ground conditions in hard-rock tunneling are associated with fault zones containing brecciated rock and gouge. Gouge is a stiff clay-like soil that exhibits a propensity to creep. The ground loads applied to tunnel supports in squeezing ground are known to be significantly time dependent. Accordingly, an experimental and analytical study is presented that deals with soil creep and its application to the prediction of tunnel support requirements in squeezing ground conditions. Relatively undisturbed samples of fault gouge obtained from Straight Creek tunnel in Colorado and Pacheco tunnel in California are classified as very stiff to hard clays of low plasticity. Constant-load undrained triaxial compression tests are performed on these materials. A simple, three-parameter creep equation is developed that adequately describes the observed deformation of fault gouge with respect to applied stress and time. The equation is shown to fit existing creep data of various soil types. The creep equation is used to modify an existing continuum-mechanics solution to the time-dependent behavior of unlined and lined cylindrical openings in a creepsensitive medium under a hydrostatic state of stress. Assuming properties for the medium that are representative of the fault gouge materials tested, parameter studies are performed for unsupported and supported tunnels in squeezing ground. The analyses permit estimates to be made of the steel set supports required for tunnels at different depths in various squeezing ground conditions.

Jan 1, 1974

By Keith S. Liddell

Gold in many ores occurs in sulphides, which, if the gold is finely disseminated, renders the ore refractory and therefore not amenable to the simple process of milling and cyanidation. Traditional methods of treatment of these refractory ores is to produce a sulphidic flotation concentrate which is roasted to form a porous calcine from which the gold is recovered by cyanidation. The roasting process imposes a constraint of a minimum sulphur grade of the concentrate on the flotation plant, which may lead to a lower gold recovery being achieved in the flotation section. Thermal decomposition of the concentrate by roasting means that the sulphur contained therein has to be treated and disposed of in an environmentally acceptable manner; and, if arsenopyrite is present in the concentrate the environ- mental aspects will be worsened. It has long been recognized that finer milling of gold-bearing materials improves the liberation of gold, especially when the gold particles are very fine. After extensive laboratory and pilot plant investigations (Liddell, Patents), a suitable mill has been developed for the mining industry by Metprotech, which is capable of producing very fine grinds (down to 90 percent passing one m if necessary). In the course of the investigations it has been found that a large number of gold-bearing materials are amenable to fine milling. A specific advantage that fine milling of sulphidic materials has over oxidative processes such as roasting and bacterial leaching is that the sulphides are not decomposed and there is therefore not a sulphur disposal problem. Furthermore, the milled sulphides can become a future sulphur feed source, and can be reclaimed if necessary. A further feature of the Metprotech process is that it is possible to add cyanide to the mill feed

Jan 1, 1988

By D. Akers, R. Dospoy

Introduction The geological processes that form coal can also concentrate trace elements in the coal. For example, the average concentration of arsenic in bituminous coal (20 ppm) is ten times the average concentration found in all the other rocks that make up the earth's crust (2 ppm). Similarly, other elements, such as antimony, cadmium, mercury and selenium, are more concentrated in coal than in the earth's crust. When coal is burned, trace elements can be further concentrated. Although no new constraints on trace clement emissions were placed on the power generation industry under the 1990 Clean Air Act Amendments, the act does mandate a three-year study of air toxics. Any new regulations aimed at electric utilities as a result of this Federally-mandated study will almost assuredly be very costly-an estimated $1 billion per year. Many trace elements in coal are associated with mineral matter. For example, arsenic is commonly associated with pyrite, cadmium with sphalerite, chromium with clay minerals, mercury with pyrite and cinnabar, nickel with millerite, pyrite and other sulfides, and selenium with lead selenide, pyrite and other sulfides (Finkelman, 1980). There are also cases in which some of these elements are organically bound. Just as both organic and pyritic sulfur can be found in the same coal, the same trace element may be both organically bound and present as part of a mineral in the sane coal. Physical coal cleaning techniques are effective in removing mineral matter from coal and can potentially remove at least some of the trace elements associated with specific minerals, thereby reducing the release of these elements into the atmosphere. Conventional coal cleaning to remove trace elements As part of a project funded by the Electric Power Research Institute, CQ Inc., a wholly-owned EPRI subsidiary located in western Pennsylvania, has demonstrated that large reductions in the concentration of many trace elements are possible if conventional coal cleaning techniques are properly applied. Four examples are given in Tables 1 to 4. In each example, the results shown were generated by cleaning the coal at CQ Inc.'s commercial-scale cleaning test facility. Cleaning results for Upper Freeport Seam coal from Northern Appalachia are provided in Table 1. Data are presented in the table in two ways: as a weight-based concentration (parts per million) and as a concentration per heat unit (grams per billion Btu). Grams per billion Btu is analogous to pounds per million Btu, but avoids the use of numbers with many decimal places. The heat-based concentration provides a better measure of boiler impacts, because the increased heating value obtained through coal cleaning reduces the number of tons that must be burned to produce a given thermal output. Reducing the quantity of coal burned reduces the quantity of trace elements entering the boiler. This raw coal is relatively high in several trace elements of environmental concern, including arsenic, cadmium and chromium. Cleaning provided large reductions in the quantity of arsenic, barium, cadmium, chromium, fluorine, lead, mercury, nickel, silver and zinc. The results for tests with a Powder River Basin coal, Rosebud/McKay, are presented in Table 2. Large reductions in arsenic, barium, cadmium, fluorine, mercury, nickel, selenium and zinc were observed with cleaning. The concentration of chromium increased with cleaning, while lead concentration increased in one test and decreased in another. Table 3 presents test results for Croweburg Seam coal from Oklahoma. Large reductions in arsenic, barium, cadmium, chromium and zinc were obtained with cleaning. Smaller reductions were obtained with lead and nickel, while chromium, fluorine and mercury increased in at least one of the tests. Table 4 presents cleaning test data for Kentucky No.11 Seam coal. In this case, large reductions were obtained with all elements measured. In general, these data indicate that physical coal cleaning is effective in reducing the concentration of many trace elements, especially if they are present in the coal at relatively high concentrations. The degree of reduction achieved is coal-specific, relating in part to the degree of mineral association of the specific trace element and the degree of liberation of the trace element-bearing mineral. The extent of trace element removal also depends on the method of cleaning the coal. Figure 1 is a washability plot, by size fraction, of arsenic vs. ash content for Upper Freeport

Jan 1, 1994

By S. J. Knoll, D. F. Scott, T. J. Williams

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep under-ground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By D. W. Fohlen, B. A. Filas

The International Finance Corporation (IFC), the private investment arm of the World Bank Group (WBG), requires all IFC-financed projects to comply with its environmental and social policies and guidelines. IFC's review process involves an environmental and social assessment and the implementation of an Environmental Action Plan (EAP) that will set forth the necessary actions to bring the operation into compliance. This paper provides an overview of the environmental and social policies and guidelines that apply to mining projects and examines how WBG/IFC policies and guidelines are applied to mining projects in developing countries. In addition, it includes a review of the increased emphasis IFC is giving to social issues over the past several years based on the existing WBG policies. IFC’s process for the environmental and social review of proposed investments is briefly discussed. The paper focuses on how IFC emphasis has shifted from the traditional environmental and impact mitigation analyses of a few years ago to the integrated social and environmental awareness, action (EAP), and implementation programs (social plans) required today. Today, IFC's focus is to promote sustainable development by investing in projects that directly benefit local communities and the environment. Examples of these changes will be highlighted by a review of recent investments located in West Africa. The goalposts have not moved, but the rules of the game have become tougher.

Jan 1, 2001

By J. W. Markham, M. Atiemo, K. Yoshida

INTRODUCTION In open-pit mining of high grade ores, operators of mining equipment in a pressurized cab are protected from inhaling radioactive aerosols by the use of filtered air through a pre-impactor and a HEPA (high efficiency particulate air) filter. At present, a limited amount of scientific information is available on the worker exposure to airborne alpha emitters in the mining of high-grade ores. (Miller, 1977, Nielson, et al, 1979). Factors affecting the worker exposure to alpha radiation are: the grade of uranium containing ores, the environmental conditions inside the mine pit, the protection factor of the cab filter system, the workers' attitude towards the hazards of radioactivity and the adopted contamination control in the cabs. Four series of field samplings were conducted during the fall of 1980 and the summer of 1981 at a mining site in northern Saskatchewan to investigate the extent of protection an equipment operator has against cab internal exposure to airborne alpha emitters with short and long half-life radionuclides. The variation in the breathing zone concentrationnof aerosols as a result of resuspension is discussed, however no attempt was made to isolate and investigate the factors and the associated parameters of the aerosol resuspension phenomenon. AEROSOL RESUSPENSION IN A CAB Mechanisms of Resuspension [Sources]: The presence of radioactive aerosols inside a cab and in the breathing zone of an operator may be due to initial concentration inside [(CO)], concentration in the filtered (HEPA) air (CC, at the flow rate [QC]), the concentration of the aerosol through resuspension ([CR]), the aerosol concentration in the air outside the cab ([CE]) and the concentration of the aerosol in the leaking air [(CL)], at the flow rate of [(QL)]. [Volumetric Equilibrium]: Assuming a uniform concentration of the aerosol in the cab, the aerosol concentration in the breathing zone[ (CBZ)] may be expressed as, [CBZ+CO+CC+CR-CL] If [QC] remains greater than [QL], there is pressurization in the cab. There is particle loss as a result of the leaking air from the tight cab, however the condition of adequate pressurization ensures that [CL ~ CC]. Also for dust particles filtered through HEPA [CC – 0] thus [CBZ + CO + CR] For the radioactive gases, [CBZ - CO + CC] Over long periods,[ CBZ – CE] but if [CBZ] exceeds the value of CE then the aerosol build-up in the cab has, occurred. [Resuspension]: Turbulent bursts are generated within the core region of a cab confinement, such that the down sweeps and the up sweeps of the air bursts cause resuspension of dust from the surfaces. Particles initiate resuspension by four major modes: namely, sliding, rocking, rolling, bouncing or sudden ejection or by combinations of these. Nevertheless the adhesion force between the particles and the surface must be overcome by ejection forces before ejection takes place (Kline et al, 1967, Corino and Bradkey 1969, Kim et al 1971). The phenomenon of particle resuspension from a surface may be expressed in a generalized form as: CR =f (Uz . R . D . H) where CR = Rate of particle resuspension UZ = Surface shear velocity R = Surface roughness parameter D = Aerodynamic diameter of particle H = Frequency of surface airburst A detailed discussion of the individual parameters was attempted for the case of farm tractor cabs by Atiemo (1981), such a treatment is out of the scope of this study. Only the effects of the properties of surface roughness will be discussed. Effect of Surface Properties The roughness of the surface from which dust particles are ejected plays a significant role in the deposition and resuspension of the dust. The roughness or the amount of protrusions greatly influence the intensity of air turbulence in the immediate vicinity of the surface (Schmel 1976). For most roughened surfaces therefore, larger particles may be dislodged in greater quantities than smaller particles. The deposition and the resuspension of dust particles from different surface materials of glass, cloth, metal and rubber have been studied in a wind tunnel (Atiemo, 1981). Field Conditions Mining equipments used are: a backhoe, a bulldozer with ripper attachment and two dumptrucks for high-grade ore operations; a payloader and two dumptrucks for waste handling; and a jumbo drill which drills dynamite holes for ore blasting. All this

Jan 1, 1981

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By B. Moudgil, M. Bogan

A bench-top centrifuge was used to study the consolidation behavior of phosphatic clays. A mathematical model (based on, first-order kinetics) was developed to describe the relationship between the void ratio (at any time) and the effective stress. The permeability of the sediment as a function of the void ratio is also described. The results of this analysis are then compared to data obtained by other consolidation testing methods. The centrifuge results indicate that consolidation data may be developed in a short period of time (hours) as compared to days or weeks when other techniques are used.

Jan 1, 1997

In conjunction with steady increases in production levels, long-wall operators have applied greater quantities of ventilating air to control respirable dust and methane gas. As a result, air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high-velocities, especially during shield advance as dust falls from the shield canopy directly into theair stream. Laboratory tests to simulate dust liberation by shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH in a wind tunnel designed to study dust entrainment in high-velocity airstreams. Dust was introduced into the tunnel to determine dust concentration as it relates to entrainment, dilution, air velocity, and particle adhesion. Airborne dust samples were obtained by iso-kinetic sampling using BGI cyclones to quantify respirable dust concentration at the various air velocities. Laboratory tests were con-ducted at velocities ranging from 2.0 to 10.1 m/s (400 to 2000 fpm),and significant differences in airborne respirable dust levels were measured. This research is being conducted to provide fundamental information on the entrainment characteristics of respirable dust at high air velocities, which will subsequently lead to solutions for shield dust control. A discussion of the test procedures and results are presented.

Jan 1, 2004

By M. S. Riyazulla

The Hutti greenstone belt comprising predominantly of low-potassium tholeitic basalt has undergone regional metamorphism of a transition zone between greenchist to amphibolite facies. The important mineral constituents of the volcanic suite are amphibole and plagioclase which appear to be the product of regional metamorphism. These minerals have been recognized as the main indicators of metamorphic temperature and pressure. With a view to understand the P-T conditions of metamorphism of the belt, electron microprobe studies were carried out on amphibole and plagioclase and the chemical data was used to decipher the metamorphic conditions. The results obtained indicated a metamorphic temperature of about 6000 c and pressure of 5 kbs. for the Hutti greenstone belt.

Jan 1, 1996

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

In this study, various rib bolting scenarios were investigated to better understand the effectiveness of the support systems. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid banded bright coal were considered. Different scenarios such as rib bolt length and number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength-reduction method in DEM code with the coal-mass model can aid in the development of practical primary sup- port charts, which can help in the rib support design process.

Feb 1, 2024

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

By Goran Mathisson

PLASMARED is a process in which one well established and one new advanced technology have been merged into a practical tool for production of high quality direct reduced iron at lowest energy consumption and costs. Before describing the process, we have to reiterate the simple fundamentals of making metallized iron from iron ores: The main components necessary are: - Iron oxide - Carbon and/or hydrogen - Heat

Jan 1, 1982

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

By Subash Chander, B. Arnold

Many developments have occurred in coal flotation with regard to increasing recovery from the flotation circuit and its impact on overall coal preparation plant recovery. This includes innovative design of flotation circuits, equipment modification and development, methods of enhancing the use of reagents, effect of slimes, and recognizing the effect of water chemistry. This paper will review recent advances and present some guidelines to improve process efficiency.

Jan 1, 2005

By C. D. Anderson

"IntroductionTungsten carbide is a valuable material used in a variety of different applications, including the manufacturing of cutting tools, bearings and as a cost-efficient alternative to industrial diamonds. Both the high hardness value (Mohs 9) and scratch resistance of this material make it a valuable commodity for use in the mining industry.Usually, the production of tungsten carbide is a multistep process involving one or more of the following unit operations: hydrometallurgical digestion, solution purification, crystallization (as ammonium paratungstate), calcination, hydrogen reduction and carbon synthesis. The proposed three-step process eliminates three of these steps (crystallization, calcination and hydrogen reduction) by implementing a combination of hydro/pyrometallurgical techniques. These include alkaline pressure leaching, carbon adsorption and carburization roasting. By eliminating some of the intermediate processing steps, there is potential to reduce energy consumption and decrease overall operating costs.Methods and resultsInitially, alkaline pressure leaching with sodium carbonate (Na2CO3) was employed to selectively leach tungsten, as tungstate (WO4 2-), from an industrial Scheelite (CaWO4) flotation concentrate. Experimental variables included lixiviant (Na2CO3) concentration, temperature and residence time. Experimental constants, based on previous work, were percent solids at 13 wt% and agitation at 400 rpm (Queneau and Strathmore, 1969). Leaching results showed it was possible to extract 97% of the tungsten present. The most favorable conditions for leaching were determined: 2M Na2CO3, temperature of 180° C and a residence time of 30 minutes."

Jan 1, 2015