Search Documents

By Fred H. Seymour

In spite of the progress made by geostatistical theory over the years, evaluation of low grade open pit gold deposits continues to be challenging. Many Carlin type deposits are modelled from exploration drilling spaced on 10C foot centers. From these drill holes, 50 by 50 by 20 foot blocks containing about 4000 tons of material are estimated. The block size is a compromise between being large enough for a good geostatistical estimation and being small enough for practical pit limit analysis and mine planning. Most of these gold deposits are highly variable and include ore and waste zones that are too small to be properly defined from exploration drilling information. Because of this, selective mining is controlled by sampling closely spaced blast holes where the density can be as high as 50 blast holes per exploration drill hole intercept. Figure 1 illustrates an example of the ore/waste contact definition before and after blast hole sampling. With exploration information only, a tentative ore/waste contact can be drawn between the exploration blocks.

Jan 1, 1989

By Michael Traylor, Michael Jatczak, Brett Robinson

The Detroit River Outfall No. 2. is an effluent water conveyance system linking the Detroit Metropolitan Wastewater Treatment Plant to the Detroit River. The 6.4m (21ft) finished diameter tunnel extends 1,890m (6,200ft) east from the bottom of a 91m(300ft) deep, 9.2m (30ft) diameter drop shaft. At the eastern terminus of the tunnel, six Riser Shafts connect the tunnel to diffuser heads on the riverbed. The tunnel runs through a highly fractured Limestone formation capable of producing high levels of groundwater in?ows and Hydrogen Sul?de gas. Control of this water and gas was a theme which ran through the entire Project’s design and construction. This paper will provide an overview of each portion of the Project’s construction, including the Entrance Shaft, Precast Concrete Segments, TBM Tunnel, Pre-Excavation Grouting Methods, and the Riser Shafts.

Jan 1, 2003

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By Lynne Chastain

The Eastern Shoshone and Northern Arapaho tribes of the Wind River Indian Reservation, Wyoming are interested in developing their industrial mineral resources. The U.S. Bureau of Indian Affairs (BIA), Division of Energy and Mineral Resources (DEMR) is assisting the tribes in evaluating the potential of their industrial mineral prospects for development. Gypsum occurs on both sides of the Owl Creek Mountains in the basal portion of the Jurassic Gypsum Springs Formation. The gypsum resources that are being evaluated crop out along the northern flank of the Owl Creek Mountains in the Sweetwater basin, a small topographic sub-basin of the Big Horn Basin. From October 1998, to April 1999, DEMR personnel mapped, sampled, and drilled the southcentral butte within the Sweetwater basin. Samples were analyzed for free and combined water, and major mineral oxides to determine gypsum purity. Gypsum purity averaged 93.6 percent for surface samples and 95.1 percent for drill core samples. The basal portion of the Gypsum Springs Formation is comprised of several beds of gypsum up to 9 feet (2.7 m) thick separated by 0.5 to 2.0 foot (0.15 to 0.61 m) thick lenses of siltstone and limestone. Overall gypsum in the formation ranges from 35 to 90 feet (11 to 27 m) in thickness. A resource of approximately 7 million short tons (st) (6.4 million metric tons [mt]) has been identified.

Jan 1, 2001

By J. R. Blair, D. P. Lindroth, W. R. Berglund, R. J. Morrell

The objective of this US Bureau of Mines (Bureau) research was to determine the technical feasibility, principles and effectiveness of a combination energy method for drilling and cutting hard rocks. Experimental test results of microwave heating and drilling in basalt and granodiorite are given. The experiments were performed with pilot-scale, commercially available equipment employing microwave energy at a standard industrial frequency of 2.45 GHz. The data indicate that penetration rates, well in excess of the state of the art, are possible.

Jan 1, 1993

By G. Davey

High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. The operating experience of two existing copper operations will be covered to show the effect of the introduction of the Metso Stirred Media Detritor (SMD) a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from the introduction of this new technology. The benefits and process difficulties are covered and explained.

Jan 1, 2003

By Terence G. McCusker, Bruno Dietl

The only previous attempt to use a tunnel boring machine in the rock formations encountered in New York City was unsuccessful. However, technology has been developed since then which made a new attempt a practical proposition. Nine thousand feet each of 8'6" and 11'0" diameter tunnels were driven in Manhattan schist using Jarva TBM's together with 1100 ft. of the smaller diameter driven conventionally in Inwood marble and earth. (1) The selection of tunneling method was largely based on the need to avoid community reaction and hazardous tunneling conditions where the larger diameter tunnel passed beneath residential structures in poor condition in seamy and blocky rock. Experimentation with cutters and cutter mountings indicate that good cutter life and ease of change are available. It was found practical to use unusually large muck cars for an efficient muck disposal system. Conventional tunneling was successfully executed beneath a subway station whose invert was less than seven feet above the crown of the tunnel. Attempts at chemical consolidation and dewatering were unsuccessful in the earth section which was completed under compressed air.

Jan 1, 1974

By M. G. Ayat

A novel tracing technique employing specifically prepared trace particles has been applied to coal preparation separatory systems. The technique employs individually prepared trace particles representing specific known sizes and densities of coal particles. These trace particles are injected into the feed, to the processing circuit, and are then detected at locations in the coal product and refuse streams. It is anticipated that on-line input of the generated partition data will be linked with computer technology to provide rapid analysis of the processing efficiency, and to allow for process control. This tracing technique can revolutionize many processing operations from the diagnostic viewpoint as well as from the coal processing standpoint.

Jan 1, 1986

By J. Routh

Analysis of AI, As, Ba, Be, Ca, Cd, Co, Cu, Fe, K,. Mg, Mn, Mo, Na, Ni, Pb, Sb, Se, Sr, 11, V and Zn in various types of samples collected at Van Stone mine (a Pb-Zn deposit in Washington) and surrounding areas indicates that the concentrations of several elements in water, soil and sediment are higher than their background. values. Concentrations of metals in water decrease sharply downstream and are below the maximum contaminant levels specified for drinking water. Under present physico-chemical conditions, contamination of water is insignificant but the enrichment of heavy metals is found in soil and sediment.

Jan 1, 1994

By Michael E. Kelahan, Glenn A. Gruber

A review of recent phosphate beneficiation developments shows that Flotaire cells, ranging from 0.20 m to 2.44 m in diameter, have been examined in pilot scale and commercial plants. Applications of the column cells have included sized feed fractions using anionic and cationic reagent systems. In plants where the Flotaire was installed as a test unit or as an optional circuit, its use has been largely discontinued. On the other hand, when management committed to installing the Flotaire as an integral part of the flowsheet, the performance expectations were met or exceeded.

Jan 1, 1988

By G. Miller

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixers. Recent experience with both large and small plants has shown that this is not the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers. Both of these lead to either reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Further, changes to the method of specification and selection of both primary and secondary mixers have been made to eliminate the onset of partial separation during operation. Observation of settler operation has shown that it is also a dynamic process, even under ‘steady state’ conditions. Four different transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze, and erratic and high entrainment levels in the discharges. A first approximation analysis has shown that there are significant pressure differentials within settlers and these change along the length and with phase separation rates. A technique to control the effects of these transients has been developed which allows plant performance to be improved beyond ‘standard’ expectations. The design and selection of the settler internals is described.

Jan 1, 2001

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

By Ricardo D. Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Russell C. Babcock, William L. Gunter, Thomas R. Gibson, Douglas N. Halbe, Jay W. Hammitt

The Barneys Canyon orebody is a sediment-hosted disseminated gold deposit located 8 km (5 miles) north of the Bingham Canyon porphyry copper mine. Mineable oxide reserves are 8.6 million tonnes (9.5 million short tons) grading 1.64 g/tonne (0.048 oz/ton) gold. Host lithologies are carbonates and siliciclastics of the Park City and Kirkman-Diamond Creek Formations of Lower Permian age. Gold distributions are controlled by favorable stratigraphic units and associated alteration, and structures. Dominant alteration is decalcification and bleaching of carbonates, and argillization and bleaching of sandstones. Gold to silver ratios are greater than 1:1. Anomalous trace metals include arsenic, antimony, mercury and thallium. The Melco deposit lies 2.4 km (1.5 miles) southwest of the Barneys Canyon deposit. It is spatially associated with a steeply northwest-dipping siliciclastic breccia in the Kirkman-Diamond Creek Formation at the contact with underlying orthoquartzites of the Freeman Peak Formation. Both gold-bearing oxidized and sulfide lithologies are present, often in sharp contact. Mineable oxide reserves are 2.8 million tonnes (3.1 million short tons) grading 2.40 g/tonne (0.07 oz/ton) gold. Anomolous trace metals include arsenic, antimony, mercury and thallium, which are generally present in concentrations greater than those at Barneys Canyon, particularly in sulfide-bearing material. A spatial, temporal and genetic relationship is proposed between the Melco deposit and late-stage gold mineralization at Bingham Canyon, although both the Melco and Barneys Canyon deposits have many similarities to Carlin-type gold deposits.

Jan 1, 1990

By D. S. Choi

This paper presents the results of geomechanics work applied to the longwall operation. The mining method was successfully adapted to US mining conditions resulting in an improvement in safety and productivity. The paper deals with various geomechanics problems associated with geologic and mining conditions.

Jan 1, 1987

By Xinchun Li, Youdi Zhang

AI is one of the computing methods, artificial intelligence performs its calculation by simulating the intelligent behavior of human beings. It is regarded as one of the most important scientific achievements in the 20th century, A1 has been developed rapidly in recent years with the development of the computer technique .The application of AI in the mineral industry has also obtained rapid progress sine AI has been used in early 1980's, such as evaluation of resource, underground mining, surface mining and mine safety etc. It has played an important role for increasing mining efficiency, improving mining management and ensuring the safety of the miner. An integrated A1 system has been developed for coalmines environment management in this paper.

Jan 1, 2002

By Yongjun Xian

The release of fluid inclusions has a strong potential for the unintentional activation of pyrite during flotation. The present study aims to characterize fluid inclusions in a natural pure pyrite. The results indicate that a certain amount of fluid inclusions exist in the pyrite. The fluid inclusions assume a variety of shapes, including long strips, oval shapes and irregular shapes, with sizes that range from a few microns to dozens of microns. From the EDS results of hollow positions that resulted from the fracture of the fluid inclusions on the pyrite surface, certain amounts of Al, Cr, C, O, Ag and Cu were clearly detected; these elements were not detected in FeS2 pyrite itself. The contents of the inclusions were released into solution when the sample was subjected to a grinding process. Under experimental conditions of 2 g of pyrite cleaned in 40 mL of pure deionized water under an inert atmosphere, the concentrations of Cu, Fe, Cl- and SO4 2- released from the inclusions reached concentrations of 3.29 × 10-6, 32.52 × 10-6, 51.57 × 10-6 and 75.90 × 10-6 mol/L, respectively. These values are significantly greater than those from the experimental nonoxidative and oxidative dissolution of the pyrite. The fluid inclusions of pyrite were, therefore, concluded to represent the dominant sources of Cu, Fe, Cl- and SO4 2- in the aqueous solution. The present investigation provides a new understanding of the source of the unavoidable metal ions in the pulp and may benefit understanding of the flotation theory and environmental geochemistry.

By S. Chander, A. Briceno

The effect of sample storage in argon and in air on the kinetics of oxidation of pyrite from a coal source was studied using accelerated-weathering tests that were performed in laboratory columns. Prior to the weathering tests, the samples were crushed, ground and stored for various periods of time in either argon or air. The test results showed a dramatic difference in the rate of oxidation of the aged samples. The interpretation of the differences was based on the hypothesis that the aging of pyrite led to the formation of surface coatings that changed with time. "Dry" oxidation produced surface coatings that had properties different from those produced by "wet" oxidation. The significance of these results to pyrite/reagent interactions during flotation and in evaluating the acid-mine-drainage potential of pyritic waste materials is discussed.

Jan 1, 1995

By Scott D. Thayer, George H. Milly

INTRODUCTION Ambient concentrations of radon and its daughter products have been measured and analyzed by a number of investigators for a variety of purposes. Principal among these purposes have been: (1) descriptive, to characterize the distribution and changes in concentrations under various conditions; (2) research in the use of radon as a tracer gas in the study of atmospheric characteristics and motions, such as eddy mass transfer, diffusivity profiles, large scale circulations, and the like; and (3) the use of radon as an atmospheric tracer in exploration for uranium deposits.* This information forms the basic data for this paper and for its placing the ambient natural, or non-anthropogenic, radon concentrations into the perspective of ambient radon health standards and lung cancer risk calculations. To enable better understanding of some aspects of the ambient radon data, review and analysis is also performed on selected measurements of radon emanation or flux from the surface of the earth into the atmosphere. These measurements have generally been made for purposes similar to those for ambient radon, i.e., (1) description of radon emanation characteristics; or (2) to support and justify the use of ambient concentration measurements in atmospheric research; or (3) in exploration for uranium. Interest is also developing in the use of such measurements for earthquake prediction. In addition, to complete the perspective, brief examination is given to anthropogenic ambient and flux radon measurements related to the mining and milling of uranium, so that comparison can he made with the values from natural sources. As a frame of reference we cite here previous summaries of studies which have presented representative values and ranges of ambient concentrations and emanation rates. H. Israel, in the Compendium of Meterorology (1951), cites eight studies of ambient radon concentrations which we have selected as representative of non-anomalous continental values. Their means generally range from [0.06 to 0.15 pCi lit-1 with the smallest reported minimum of zero and the largest maximum 0.53 pCi lit-1. The overall mean is 0.10 with a standard deviation of 0.03 pCi lit-1. Means over oceans are much smaller, and the data scarcer, with only three values ranging from 0.0004 to 0.003 pCi lit-1 and a mean of 0.0016 pCi lit-1.] Thirteen studies from Israel's list were selected as representative of mountainous terrain. These data, except for the cases of higher elevations, frequently show significantly higher values than the average cases in non-mountainous terrain described-above. The averages range from 0.10 to 0.59 pCi lit-l; the smallest minimum is zero and the largest maximum is 9.2 pCi lit-1. The overall mean is 0.30 with a standard deviation of 0.17 pCi lit-1. Israel also cites five studies of radon emanation (flux) from the earth's surface. These show a mean of 0.40 pCi-2m-2 sec-1 and a range of from 0.21 to 0.74 pCi m-2 sec-1. Data on flux are naturally scarcer in the literature than data on ambient concentrations, because of the greater interest in and utility of the ambient information. In this paper we also give special consideration to observations of the variability in time and space of radon flux rates, and to the impact of these phenomena on the use of such data for a variety of purposes. NATURAL(NON-ANTHROPOGENIC)AMBIENT RADON CONCENTRATIONS We have examined the following reports for the data selected for this category; these studies were generally intended to describe radon characteristics in the atmosphere. Jonassen and Wilkening (1970); Bradley and Pearson (1970); Wilkening (1970); Lambert, et al (1970); Pearson and Moses (1966); and DickPeddie, et al (1974). Another set of studies which was reviewed was selected because the investigators made ambient radon measurements in the course of examining the use of radon as a tracer in atmospheric research. This set consists of: Israel and Horbert (1970); Carlson and Prospero (1972); Subramanian, et al (1977); Larson (1978); Cohen, et al (1972); Hosler (1966); and Shaffer and Cohen (1972). Finally, unpublished data from uranium exploration activities (Milly and Thayer, 1976) was analyzed. [Treating the ocean cases first, the mean values are generally consistent with those quoted earlier from Israel (0.0004 to 0.003 pCi lit-1); they range from 0.001 to 0.011 pCi lit-1, with 0.003 the most frequently reported value. Continental values, from eight studies, range in means from 0.07 to 0.41 pCi lit-1 (not including mineralized areas, or "uranium country", discussed later), with maxima as high as 2.4 pCi lit -l. For comparison, the means from Israel are 0.06 to 0.15 pCi lit-1, with a maximum of 0.53 pCi lit-1. Some of these studies also present the typical decrease of-1 concentration with height to 0.01 to 0.04 pCi lit at 5 to 7 km. The vast numbers of uranium prospecting radon data of]

Jan 1, 1981