Search Documents

By Wenbing Guo

Surface subsidence for fully mechanized thick seam top coal caving was measured, and surface subsidence characteristics were then analyzed. The subsidence initiation distance from the set-up room and the advance influence distance ahead of the advancing longwall face were studied. The maximum surface subsidence velocity and the delay angle of the maximum subsidence velocity were determined. The results indicated that surface movement was intensive, the surface subsidence velocity was very high, the ground surface was badly damaged, and the subsidence initiation distance from the set-up room was smaller than that in general geological and mining condition.

Jan 1, 2011

By Clare Offner

In 1998, the Australian Coal Association Research Program (ACARP) awarded funding to the School of Mining Engineering at the University of New South Wales to establish a rockbolt testing facility to research anchorage mechanisms associated with fully encapsulated rock bolts and to develop standardised testing procedures for rockbolts. This facility is still under development but has already been used to evaluate the effect of bolt profile and confinement on the load transfer characteristics of a resin encapsulated rock bolt. This paper describes the test facility and presents some of the results of development testing to date.

Jan 1, 2000

By Leigh J. Wardle

Significant coal reserves in New South Wales lie under areas with steep topography such as valley slopes and cliffs. Subsidence predictions are difficult to make for these locations as existing empirical databases cannot cover all permutations of topography and mining geometry. Two dimensional numerical model alternatives are of limited applicability. Consequently a novel three-dimensional numerical model is developed including the detailed panel layout, realistic rock mass properties including the full stratigraphy, goat behaviour and actual surface topography. Model results show the same trends as subsidence measurements from Baal Bone Colliery in the Western Coalfield of New South Wales

Jan 1, 1992

By Deren Zhu

Based on the results of field observation and physical model analyses, a computer simulation method, FEAEBP, has been developed for simulating the breakage of the main roof by considering it as a Kirchhoff plate on Winkler elastic foundation. By this method various parameters of rock property, different boundary conditions of the working face and the initiation, development and results of the breaking process of the main roof with different geometric dimensions can be effectively simulated. Since the main and immediate roofs, and the coal seams are treated as an integrated mechanical system, the interaction among them can be studied in detail.

Jan 1, 1988

By A. Bortolussi

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables an tool performance (cutting rate and bead wear) has been elucidated.

Jan 1, 1992

By G. P. Neobutov

The near surface inclined gold ore deposit is mined out at freezing temperature. The replacement of ore pillars by artificial freezing rocks during the rock pressures control in this conditions presented no difficulties. At the present, the mining operations are maintained at a depth of more than 300 meters. The exploration of mining conditions showed partial warming of rock mass and unstable ground conditions. Analytical calculations using a mathematical model of heat exchange predicted undesirable duration of freezing of artificial pillars. Practical techniques and recommendations for mining with ice pillars as an artificial support system using a new freezing method are discussed.

Jan 1, 1996

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

Researchers from the National Institute for Occupational Safety and Health's Spokane Research Laboratory installed Split-Set rock bolts instrumented with strain gauges to document the mechanical load response of the bolts in weak ground. Short-term monitoring of the bolts immediately after installation showed that some of the gauges went into tension. It was felt that the force exerted on the bolts to drive them into the hole should have caused the gauges to show compression. The tension probably resulted from the holes having crooked sections. Long-term monitoring over the course of a year also showed that the bolts were bending at some locations and that loads as high as 98 kN (22,000 Ib) were recorded along sections of the bolts. Load cells were placed on the head end of the bolts to determine head loads. Head loads up to 14.7 kN (3,300 Ib) were generated during bolt installation. In addition, closure readings were taken across the drift to determine the convergence rate responsible for bolt loading. A Rock Mass Rating (RMR) was calculated at the site to compare with bolt response. The bolts were installed as part of the rebolting process in an area being repaired because the near-vertical beds in the walls were buckling and causing the wall to fail. The instrumented Split-Set rock bolts will provide data that will lead to greater understanding of the behavior of the rocklbolt support mechanism. It may also be possible to explain the overall performance of the bolts in situ in terms of their design effectiveness. This work showed that load at the head of a Split-Set rock bolt was less than load along the interior of the bolt.

Jan 1, 2005

By Russell Frith

Probably the most expensive but least well understood roof falls in underground coal mining, are those that occur ahead of the powered supports in the centre of longwall face. Even small roof cavities result in the dilution of the ROM product and large cavities can stop the face for days if not weeks and the incurred cash flow losses can be catastrophic. Expensive and time-consuming remedial measures (e.g. PUR, cavity filling, removal of stone from the AFC by hand) are required and equipment wear and damage can be significant when the need to blast and convey stone is also considered. Through four major research projects within the Australian coal industry and numerous consulting assignments, the author has spent the best part of fifteen years attempting to identify and defme the various geotechnical and operational factors that determine whether a major roof cavity occurs ahead of the powered supports or a normal goaf fall occurs just behind them, the difference in operational outcome being enormous. The paper presents a condensed summary of the overall technical findings covering such issues as roof fall mechanisms, the measured influence of cover depth, periodic weighting of massive strata units and its quantification, the role of cut-throughs in chain pillars, face width and height, the role of the powered support and the influence (both positive and negative) of mine site operations. The big picture outcome is the view that high production longwall extraction is well-suited to certain geotechnical environments, is marginal in others and under certain conditions is fatally flawed and beyond the control of mine operators, although fortunately the latter category is a relatively rare situation. Various risk-based research findings in this regard will be given as a basis for future discussion.

Jan 1, 2005

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By Bruce K. Hebblewhite

Tower Colliery is a longwall mine operated by BHP Coal Illawarra Collieries, Southwest of Sydney, Australia It mines the Bulli Seam at a depth of approximately 450m. The surface topography overlying the mine consists of several steep-sided river gorges, up to 68m in depth, which run at oblique angles across a sloping terrain Apart from some light rural development, the surface land is essentially natural bushland, but is traversed by a major freeway. This crosses one of the gorges on twin, six-span, box-girder bridges, with bridge piers up to 55m in height. Consequently, a major surface subsidence monitoring program has been in place for several years now, including intensive conventional, GPS and E DM surveying, plus real-time monitoring of critical components of the bridge structure. Although the bridge and freeway are outside the conventional angle of draw' subsidence influence criteria, and have seen only negligible vertical deformation as a result of mining, there has been widespread evidence of regional horizontal deformation of the land surface, large distances away from the mining area The effect at the bridge has been well within acceptable tolerances, primarily because of the regional nature of the movements, with very little differential movement observed at the bridge piers Gorge closure and evidence of large headlands of land moving `en masse' have been observed. Horizontal movements of hundreds of millimetres have been recorded in some locations where gorge closure has been monitored. Possible explanations of these movements include one or a combination of mechanisms such as pre-mining stress relaxation. valley notch effects, valley bulging, regional joint patterns, movement toward active goaf areas, vertical gorge shearing' and shear failure of horizontal bedding planes below the surface This paper presents a case study of the regional horizontal ?subsidence displacements? measured during mining. and a discussion of the possible explanations for these phenomena

Jan 1, 2000

By Clarence O. Babcock

Since Vicat in 1833, the width to height ratio of a mine pillar has been taken as the fundamental variable in pillar design. From work in the laboratory by many investigators testing rock, Coal and concrete samples, it has been concluded by some that pillars with a width to height ratio of 10 to 1 are indestructible. It has also been concluded that a constrained core exists within the pillar which increases the pillar strength. The role of the roof and floor, if mentioned at all, is often noted in an incidental way. In the present work on laboratory testing of model pillars on concrete, coal, and rock instrumented with special strain gages, it was concluded that the end constraint and not the width to height ratio is the significant variable in determining the pillar strength. In tests where the end constraint is steel, a large compressive stress is produced on the horizontal plane of the pillar, and this effect increases as the width to height ratio is increased, resulting in an increase in pillar strength. If the end constraint is not steel but something with a small Young's modulus, the state of stress in the horizontal plane may be tensile, increasing as the width to height ratio increases, resulting in a decrease in pillar strength. Related to mining, the results are that a large width to height ratio pillar is strong for strong roof and floor and weak for weak roof and floor. That is, the roof and floor and not the width to height ratio determine the pillar strength. The confined core condition should be verified by testing if large pillars are to be used. If there is no confined core or the pillar is in tension, smaller pillar sizes should be used. The final conclusion is that the geometry alone is meaningless in pillar design.

Jan 1, 1984

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory are developing a borehole profilometer to dynamically measure the roughness pro-file of boreholes used to install roof bolts fully encapsulated with resin. Numerical measures of roughness were calculated from profiles of borehole surface roughness to determine potential roof bolt anchorage capacity. The concept of dynamically profiling was proven through the following series of laboratory tests: a sensitiv-ity test using various grits of sandpaper, a known-profile test along a section of a concrete hole, and a simulated borehole test in a pipe with machined grooves. Two profilometer prototypes were devel-oped that measure slight changes in the radius of a borehole using either strain-gauged, spring-steel arms or rigid, steel arms attached to a spring-loaded cone and a linear potentiometer. Both instruments performed reasonably well in the laboratory and were subsequently tested in boreholes drilled in two concrete blocks using different drilling techniques to obtain three different borehole surface roughnesses. A Z2 roughness parameter was calculated with data from the first profilometer, and an average radial increment was calculated from the test results of the second profilometer. Although both instruments were able to readily distinguish the difference between smooth and rough boreholes, the correlation coefficient (r2) for a linear relationship between Z2 and average radial increment was 0.577. Pull tests were conducted with resin bolts installed in the concrete blocks, but maximum pull-out strength could not be correlated to borehole roughness because in each of these tests, failure occurred at the resin-bolt interface. A more sophisticated prototype has been designed to measure surface roughness and also accurately determine the location and tilt of the instrument in the borehole. However, this instrument has not yet been fabricated or tested.

Jan 1, 2007

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By Anton Sroka

The dimensioning of shaft safety zones is a substantial task of mining subsidence engineering. On the one hand, the coal reserves in shaft proximity are to be mined as complete as possible, because they can be made accessible economically. On the other hand, the maintenance of the shaft operation is to be ensured at each time, since shafts represent the most important link between underground and aboveground. Regarding these two criteria, this publication presents a model for the optimization of shaft safety zones. Beyond that, extraction methods in shaft safety zones are described, in particular with consideration of minimized mining influences on the shaft.

Jan 1, 2005

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By Hani S. Mitri

The behaviour of grouted cable bolts used for rock reinforcement as a means of ground control in hard rock mining is investigated. The study utilizes an analytical model which is based on the variational principle to calculate the shear bond stress distribution along the embedded length of cable bolt. In this paper, a comprehensive parametric study which covers both geometric and mechanical design parameters involved is presented. Special emphasis is placed on studying the characteristics of the grout model represented by Winkler springs. This involved varying the maximum shear strength of the grout, its residual strength and the slip occurring between the cable and the borehole wall.

Jan 1, 1990

By Thomas Lautsch

After a short description of geology and gateroad roof support technology in the German coalfields the development of roof bolting as primary roof support is presented. Based on geotechnical parameters, different strategies used for roof support at depths of 3,300-4,600 ft. are explained. Strict quality management and a strict monitoring program are part of the entry development. A number of recently finished developments are described such as the introduction of standardized bolts and accelerated resin systems. An outlook of future goals is presented. The paper concludes with a comparison of roof control systems at RAG's mines in the US and Germany.

Jan 1, 2000