Search Documents

By Collin L. Stewart

A summary of the results of a limited subsidence monitoring program at Cyprus Amax Coal Company's Shoshone Mine No. 1 in the Hanna Basin of south central Wyoming is presented. The monitoring program was designed to meet regulatory requirements for confirmation of subsidence predictions made in the mining permit. The longwall panels were 380 ft to 600-ft wide. Mining heights varied from 11 ft to 13.5 ft. Gate road development included three-entry and two-entry head and tail gates. Overburden depth varied from 150 to 945 ft. The coal seam and overburden dip at approximately 11 degrees. The overburden is very low to low strength mudstone and carbonaceous shale with low to moderate strength, silty sandstone interbeds. Panel W/h ratios varied from subcritical to supercritical. Smax was 0.9 of the mining height. The subsidence ratio was about 0.6 for subcritical width. The draw angle on the up-dip side averaged 20 deg. The draw angle on the down-dip side averaged 12 deg.

Jan 1, 1995

By Denise Y. Dizon

The objectives of this study were to document the hydrologic impacts of longwall mining on streams, identify the factors affecting the extent of stream dewatering, and develop empirical trends to predict the extent of dewatering and recovery of streams in advance of mining. This study on stream impacts is a companion to a stud; conducted on ground water impacts from longwall mining, which was done as part of the same research project at the' same locations and times. The study areas are three mine sites in north- central West Virginia. Mine A, located in Upshur County, has relatively thin mine overburden under the valley streams (105-115 feet). Stream monitoring there continued the earlier work of Cifelli and Rauch (1). Stream dewatering was severe with streams often going dry over the longwall panels during baseflow conditions. The lost water was probably flowing to the mine. Dewatering began in streams over the mine entry areas adjacent to the panels and as much as 380 feet from the nearest panel edge. The angles of dewatering influence ranged 22 to 72 degrees with respect to the nearest mined panel edge. Discharge then typically increased as the streams- flowed across the panel edge, but then decreased again over the panels. These streams were often ponded by local reversals in hydraulic gradient caused by land subsidence, and often dried up after flowing a few hundred feet across the panels. This occurred over panels that were previously mined up to eight months before. Mine B, located in Monongalia County, has relatively thick mine overburden (475-485 - feet) under the major stream. Stream dewatering was severe there during warm season baseflows, with complete dewatering occurring then over the longwall panels. This dewatering occurred over mined panels up to five years old, probably in response to a major anticlinal axis lineament and fracture zone in the stream valley. Mine C. located on the West Virginia -Pennsylvania border, has relatively thick mine overburden (about 585-630 feet) under the monitored streams there. stream dewatering was only partial, and these streams typically recovered their lost discharge downstream of the mine, indicating that lost water was not recharging to the mine. Only longwall panels less than one year old were associated with stream dewatering.

Jan 1, 1990

By Nikolaos Polysos

For the planning and driving of gateroads supported by roof bolts a practical concept has been developed in order to determine the geological and rock mechanical parameters derived from exploration drillholes. Based on this, an assessment scheme for the design of roof bolting has been established. The new methods of investigation comprise of geotechnical logging of drill cores for the determination of structural-geological rock characteristics and complementary geophysical well-logging which enables the evaluation of petro-physical and rock mechanical properties. The tools and their measurements will be briefly presented. The relationship between the geophysical log readings and the geotechnical parameters will be illustrated. The aim of the data acquisition is to improve roof bolting design which is based on the assessment scheme. This will be adjusted to the prevailing rock mechanical conditions and stands up to the required stability of the gate roads. In order to ensure consistent data acquisition, a method of core logging has been standardized for the respective demands. To achieve this it was necessary to introduce specific parameters and new methods. For the recording of linear and planar structural elements at the drill core, a special system for the documentation of the angles in relation to each other has been set up. The rock mechanical parameters and their acquisition will be explained. In order to carry out an objective analysis as fast as possible, software has been developed for the acquisition, management and presentation of the data. These programs and their functions will also be presented. The software is characterized by being user-friendly and the flexibility of its interfaces, Different options for the combined presentation of input and evaluated data give a more objective basis for the planning of roof bolt design. Examples will illustrate the operational implementation of the results during the planning and driving phases.

Jan 1, 2001

By George Gardner

The rapid growth of highwall mining in the Appalachian coalfields has resulted in unique safety concerns. Due to the concentration of activity at the base of the highwall and the potentially destabilizing influence of the mining process, proper mine planning and continual monitoring of the ground conditions is essential to ensure a safe and productive operation. This will also help to minimize the need to recover equipment that has become entrapped underground, and the subsequent hazards associated with a recovery operation. Adequate geotechnical site investigation and rational design methods should enable mine planners to properly account for the site-specific conditions that influence web and abutment pillar, roof, floor, and highwall stability. This paper examines the growth of highwall mining, provides a general overview of the various safety concerns, and reviews the modes of highwall failure as they relate to a highwall mining operation. Gcotechnical considerations that should be taken into account before and throughout the mining operation are emphasized. The importance of closely examining and monitoring highwall conditions for subtle signs of highwall instability will be discussed.

Jan 1, 2002

By A. G. Pasamehmetoglu

The swelling process is an important problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from pedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the pedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By Stephen C. Tadolini

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that arc easy to handle/install under temporary or previously supported roof.

Jan 1, 2001

By J. D. Cole

In order to reduce the number of longwall face moves and to increase the rate of gateroad construction, super longwall panels, 1000 feet wide and 12000 to 14000 feet long, are planned for Wolf Creek Collieries No. 4 mine. The development of the longwall panels at the mine has evolved from 5-entry, to 4-entry, to 3-entry systems. A three-entry system including pillar size and entry supporting method for the super longwall panels was designed for long-term stability. The design procedures included field observation and studies, laboratory properties tests, in-situ stress measurement, and computer analysis. Three pillar design methods consisting of PILLAR, ALPS, and the Wilson Method, and one entry supporting method, ROOFBOLT, were adopted in this study. The procedures, methods, and results are discussed in detail.

Jan 1, 1990

By Greg Hendon

Longwall developments in the UK have historically consisted of single entry gate roads. Adjacent developments were separated from existing panels by large barrier pillars (designed of sufficient width to get away from the longwall abutments of the previous panel) or by small barriers driven in the shadow, or de-stressed zone, of the previous panel. Some 2nd panel tailgates were also driven skin to skin leaving no coal barrier between the newly driven entry and the heavily supported existing gateroad. With the developement and wide acceptance of fully bolted entries and the pressure to reduce production costs, alternatives to single entry drivage, particularly yield pillar developments, were examined. Through the Rock Mechanics Branch of British Coal, a cooperative study was begun with Jim Walter Resources, Inc., USA, (JWR) to look at the yield pillar alternative in detail. This study was to determine the feasibility of utilizing yield pillars in the UK and to determine, through monitoring, the possibility of reducing stable pillar widths at JWR. The study has included extensive monitoring of the yield-stable-yield pillar system at JWR No. 7 Mine and an underground trial of a two entry yield pillar test area at Welbeck Colliery in the UK. This paper describes results from the JWR study and the subsequent results of the first advancing yield pillar development in the UK at Welbeck Colliery.

Jan 1, 1995

By Vasundhara

Underground coal mining in soft floor environments has often led to strata control problems ranging from small scale issues such as floor heave which disrupts traffic and ventilation, rib spalling and induced fractures in pillars, through to large scale instability and long term subsidence. Past investigations of the problems encountered in Newcastle Coalfields of New South Wales, Australia, have revealed that the soft floor unit comprises of claystone which is very sensitive to moisture. It is prone to swelling, reduction in stiffness and loss of strength in the presence of moisture. Long term stability of mine panels in such an environment is governed by the extent of deterioration of the floor strata. The paper reports the field investigations conducted at Cooranbong Colliery to assess the extent of softened floor zone in the roadway and under a pillar.

Jan 1, 2001

By James Arthur

In deep coal mining the support of the underground roadway is fundamental and without knowledge of the mechanics of ground control a mine is unlikely to be operating safely and efficiently. It is therefore important for the support system to be designed sat¬isfactorily for the size of the excavation required and to do so an understanding of the behaviour of the surrounding strata is re¬quired. Over the last 15 years there has been a major change in the industry and the support systems adopted. The industry has been privatised, legislation has been updated, a comprehensive research programme has been carried out and guidance docu¬ments produced. The paper will show how privatisation has not allowed support standards to deteriorate, highlight research, the legislation and guidance documents updated and how this has led to a reduction in accidents and falls of ground..

Jan 1, 2002

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By David Bigby

The paper describes research undertaken on an ECSC/K HSE project which investigated several potential physical principles which might be harnessed to provide a non-intrusive means of determining the extent of failure in the near roof of mine roadways and tested the most promising in the laboratory and in the field. It was concluded that the principles which warranted further development were thermal response and laser vibration measurement. In the latter case there is a need to develop an efficient means of imparting energy to the seam to induce sufficient vibration. A new, SIMRAC funded Project will progress work in the field of thermal response.

Jan 1, 2004

By Deren Zhu

The principle of roof control in longwall mining is to control main roof fractures so as to reduce roof weighting, plus reasonable and effective design of supports to reduce the convergence and premature caving of the immediate roof. This paper introduces a comprehensive test for better roof control based on the geological conditions of coal seam No. 16 in Zaozhuan Colliery, China.

Jan 1, 1990

By Shuangsuo Yang

Coal ribs can roughly be divided into three types: (1) roof and floor rocks are similar to ribs, (2) roof and floor rocks are stronger than ribs, and (3) roof and floor rocks are weaker than ribs. Different types of roof/floor and ribs will exhibit different types of ground pressure around an entry. Most coal mines belong to the 2" type with ribs fractured or even broken. In this case the mine ground pressure depends on the occurrence and development of deformation and fracture of the ribs. If it's not properly controlled, the following deteriorating process will follow: the roof bent downward > the ribs squeezed and broken > rib sloughing and collapse > rib support to the roof reduced > the roof bent downward further > the ribs broken further. In this paper rib instability is divided into four types: compression/shear sliding rib fall, gravity sliding rib fall, cross arch rib fall, and cleavage rib fall. Since failure in thin walls is largely of tension type whereas that of thick walls by compression or shear, a concept is proposed here to utilize a thick bolted rib to stabilize entry ribs, i.e. the thickness to height ratio of the thick bolted ribs

Jan 1, 2005

By T. N. Singh

With a view to producing increased target output every year, Indian coal mining industry is fast moving towards mechanisation but the present approach of mechanisation suffers from lack of standardisation, mainly due to nonavailability of the cutting data for various machine/rock combinations. The coal seams of the country are relatively hard in nature and the coaling machines are reported to be affecting production and productivity of the coal mine and the very trend of mechanisation. This paper presents the result of extensive study performed to visualise the cutting characteristics of coal seams of compressive strength ranging from 20 MPa to 65 MPa. In a specially designed drag bit type coal plough rig, continuous recording of cutting forces was done with the help of a microprocessor based data logger and the specific energy of cuttability was evaluated at different depth of cut and speed of cutting. The geomechanical properties such as compressive strength, orientation and frequency of cleats etc. and different indices of coal seams were measured in the laboratory and field and relationship was developed for easy determination of specific energy.

Jan 1, 1992

By Lawrence R. Artler

The North American Coal Corporation, its subsidiaries and other coal companies, have been mining the Pittsburgh #8 seam in Eastern Ohio for several decades. Underground mining by the "room and pillar" method, and more recently by longwall methods, have been practiced. This presentation deals with ground control problems and subsequent solutions to those problems for both mining methods. But first, let me briefly discuss some pertinent points about the geologic conditions of the coal seam near the southwest edge of the Pittsburgh Coal Basin. The Eastern Ohio region of the Pittsburgh Coal Basin is situated along the western edge of the unglaciated Allegheny Plateau. The local terrain is quite steep, with topographic relief of 430-500 feet being common. The coal thickness in the region ranges from 36"to 120", with the average being 60" in the areas being currently mined. Regional dip of the seam is toward the southeast in an amount of 10 to 40 feet per mile. A cross-section of the mineable seam generally consists of the main bench (60"), a rider coal (6"-12"), and a claystone parting (6"-12") for a total excavated height of 6-7 feet. Greater excavated height occurs where the fireclay floor is so soft and friable that movement of mechanical equipment breaks up the first 4-8 inches. Generally, the main bench and rider coal thin and become more variable toward the southwestern portion of the mining area. The rider coal also grades laterally into a coaly carbonaceous shale. In those areas where the roof coal can no longer be counted on to help support the immediate top, some of the main seam (6") is left to protect the overlying 8'-12' of mudstone/claystone strata. These strata are virtually non-bedded, highly slickensided units and are "hung in suspension" by roof bolts from a more competent limestone stratum above. These mudstone/claystone units are very susceptible to moisture and thus to the weathering cycles. The rider coal or 6" of the main bench is left in place to "seal" the mudstone/claystone units in Mains and Submains development. For many years, it was thought that the strength of the limestone member was detrimental in attempts to fully extract the seam by conventional means; however, longwall methods that have been more recently employed have broken the "myth" that the Redstone Limestone prevents full extraction of pillars.

Jan 1, 1984

By David C. Johnson

Coal mining in Illinois has resulted in many structures being exposed to subsidence damage. Damage mitigation techniques (DMT) applied in the foundation design/construction have proven successful in minimizing damage in several test cases. To determine the practicality of these techniques, the Costs of their application are investigated. The AMT costs are compared to foundation and total house costs for various classes and sizes of houses. An economical and effective subsidence resistant foundation construction is proposed.

Jan 1, 1993

By Patrick S. Artrip

A deep mining operation in the Lower Kelly (Imboden) seam in Wise County, Virginia experienced severe ground control conditions in its attempt to develop reserves situated under increasingly higher cover conditions. Ultimately one of only three mines capable of providing access to a large reserve area had to be abandoned. A thorough geotechnical exploration program was carried out to allow characterization of the critical roof and floor rock strata in accordance with the modified geomechanics classification system. The principal roof and floor rock stratigraphic sequence types were defined and mapped throughout the reserve area along with other critical geological factors. A ground control study based on the geotechnical findings provided a quantitative analysis of the causes of previous entry instability. Further analysis of pillar and entry stability identified configurations which would remain stable for the variety of strata types and range of overburden depths within the remainder of the reserve. Mine designs based on the geotechnical evaluation have, to-date, provided the stability required for long-term future development - of the reserve area. However, some areas of difficult ground were encountered which could not be anticipated with the drill data available at the time of the original study.

Jan 1, 1993

By H. Gene Wilson

Mobile Roof Supports (MRS) look similar to a longwall shield on crawler tracks. The MRS units offer a safe, productive method of extracting the 40% to 60% product left normally unrecovered in room and pillar mining. The units feature radio control, self-contained power units, crawler track drive, and a 600 ton yield. Cribbing and setting posts in retreat mining has been a necessary burden to production. The MRS reduces this burden. Long blocks of coal can be developed to further reduce move and tram time, thus increasing production. The MRS units have successful safety records. The workers are removed from the immediate fall area, and we feel back injuries have been reduced by the workers not setting posts. While MRS units have been damaged in falls, the other capital equipment has been unharmed. The MRS product line has undergone normal product improvement and evolution. Product evolution is seen in our development of machines for particular mine requirements. Through the continuing development of the MRS, Fletcher presents the coal industry with a safe, productive method of retreat mining with potential to develop new mining methods.

Jan 1, 1990