Search Documents

By Mark Van Dyke, Gamal Rashed, Khaled Mohamed, Timothy Barton, Morgan Sears

"The unconfined compressive strength (UCS) of coal is an important parameter that controls the stability of coal ribs in underground mines. Estimation of the UCS of coal units composing the rib is required for conducting the rib stability assessment technique. This technique requires conducting large numbers of conventional UCS tests in a laboratory, which are expensive and time consuming. The research work outlined in this paper examines the use of indirect strength estimation methods—the point load test (PLT) and the in-situ Schmidt hammer test (ISHT)—for evaluating the intact strength of coal. The conventional UCS test was conducted on 80 coal specimens from 10 different coal seams for eastern coals. For each coal seam, the PLT and the ISHT were compared with the UCS test results to establish a correlation between the strength indices from the PLT or ISHT and the UCS. Moreover, to simplify the estimation of the UCS, a correlation between the megascopic coal lithotype and UCS was established.INTRODUCTIONBased on Mine Safety and Health Administration (MSHA) reports, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States over the past decade (MSHA, 2018). In an attempt to control rib failures in underground coal mines, the National Institute for Occupational Safety and Health (NIOSH) is working on developing a coal rib stability rating technique to provide a quantitative means to characterize the stability of coal ribs and to provide guidelines for early selections of rib support. The unconfined compressive strength (UCS) of coal units composing the ribs is one of the key input parameters required to estimate coal rib stability. The UCS of coal is an important parameter that controls the resistance of coal ribs to fracturing and slabbing. Direct determination of the UCS is time-consuming and expensive. Moreover, the UCS may be limited to testing only the strong coal samples since the weak or highly cleated samples might not survive the transportation and the preparation process (cutting and grinding). Therefore, alternative methods have been tested to indirectly find the intact strength of coal, such as the point load test (PLT) and the in-situ Schmidt hammer test (ISHT). The acronym ISHT refers to Schmidt hammer tests that were conducted in-situ on coal pillar ribs, while the acronym SHT refers to tests that were conducted on small scale blocks of coal."

Jan 1, 2018

By Shane McDonald

Australia produces approximately 84 million tonnes of coal per annum from 30 longwalls in New South Wales and Queensland, operating at an average depth of around 300m. Industry trends and expectations place increasing emphasis on the reliability of these operations; for example, the current average face width is 245m and this is expected to increase to approximately 270m by 2010. In recent years, Beltana No.1 Mine has consistently been Australia?s highest longwall producer, with ROM output of 7.2Mt in YEJ2007. Strata management has become a key feature of the operation of Australia?s longwall mines, as a tool to manage variances in the geotechnical environment. This involves an understanding of the impacts of the geotechnical environment on ground behaviour and the implications for mine design, stability and associated support, interaction and horizon selection. The anticipated ground control impacts of these factors form the assumptions that drive the format of plans specifying both triggers and actions, with quantified, monitoring-focussed experience used to refine the plan in a continuous improvement (ie ?plan-do-check-act?) process. This paper summarises the Beltana No.1 Mine strata management methodology and experience to-date.

Jan 1, 2008

By Stephen C. Tadolini, John Bolton, Bre-Anne Sainsbury, Tom Meikle

"The capacity of ground support components which have been affected by corrosion is reduced and may ultimately lead to dynamic failure of the component and the strata. In order to maintain an effective, long-term ground support system, significant campaigns of rehabilitation are often required in corrosion affected areas which also expose the workers to hazardous conditions. The most common corrosion protection for steel ground support utilises sacrificial systems such as galvanising. Galvanising has previously been proven to be susceptible to some corrosion processes. Stainless steel is the most effective in resistance to corrosion, but can be cost prohibitive, and its mechanical properties often make it unsuited to use in ground support components.Providing an outer protective plastic coating to bolts has proven to be an effective means of protecting the inner steel bar from corrosion. However, these support systems tend to be susceptible to coating damage, and require post cement grouting to provide full encapsulation. In comparison to a standard bolt/resin system, they can be slow to install and expensive. These systems have also been shown to reduce overall load transfer performance of the bolting system.In order provide a higher level of corrosion protection whilst maintaining current installation practices and bolting cycle times, Minova has developed the Enduro™ Steel Ground Support Range. The Enduro™ range consists of standard Minova steel ground support components which have been treated with a unique coating process. The Enduro™ coating has been tested in the harshest of conditions, in laboratory controlled conditions and in underground trials. It has been proven to effectively resist or completely eliminate the formation of corrosion, even in the most aggressive environments. This paper explains the process and provides the details of the laboratory and underground corrosion performance testing carried out on Enduro™ ground support products.INTRODUCTIONTraditionally, the most common form of corrosion protection in steel ground support consists of a sacrificial protective coating such as galvanising (Aziz, et al., 2013). Such coatings have proven to be ineffective in extreme high and low pH conditions with corrosion of the support system commonly encountered. There is also evidence that common forms of galvanising may actually increase the rate of corrosion in certain pH environments. Figure 1 shows typical corrosion and failure of a standard re-bar roof bolt."

Jan 1, 2016

By Robert Kimutis, Ke Yang, Yi Luo, Jianwei Cheng

"Surface subsidence processes, especially those associated with a longwall mining operations, could cause operational and/or safety problems to railroads. For railroads with normal amounts of traffic, both the limited time window between traffic and the limited space available make the efforts to return the railroad back to its original state nearly impossible. In order to ensure the safe operation of a subsiding railway, the partial lifting method has been developed and applied. This paper describes the principle and application of the method. A case of applying this method to mitigate subsidence effects on a long section of railway has been demonstrated.INTRODUCTIONMaintaining an operational railway as it is experiencing a longwall subsidence process is not an easy task. The subsidence process may induce sufficient strain and curvature to cause problems to the railroad structures. Localized subsidence-induced slope often is significantly larger than the permissible ruling gradient of 0.7% for a locomotive to haul a loaded train reliably. In order to ensure safe operation, it would be ideal to instantly lift the railroad track back to its original level as it is subsiding. However, it is often impractical to do so due to the limited time windows available between railway traffic and the available space on the railroad base.A partial lifting method has been developed to keep the railroad operational under such limitations. The subsiding railroad track is raised by only a determined, partial amount of the occurred subsidence at a given time. By making such a determined adjustment, the railroad track can be maintained on a smooth and operational profile, and the high strain and curvature on the railroad structures can be reduced as well. To define a smooth railroad track profile in a subsided section the following two conditions should be met: (1) the maximum railroad gradient should be less than the permissible ruling gradient, and (2) the recommended amount of adjustment should be able to be made by the repair crew within the available time windows between scheduled railway traffic.The subsidence effects on a long section of railroad over two longwall panels have been successfully mitigated using the partial lifting method. The railroad experienced a maximum subsidence 89 of about 5 .0 ft (1.5 m) with the average subsidence along the entire length being about 3.45 ft (1.05 m). However, the average adjustment due to lifting that was made along the entire length of the subsidence-influenced railway was only 0.5 ft (152 mm)."

Jan 1, 2010

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By B. Tulu, D. Gearhart

A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia. Monitoring was initiated a few days after development of the gateroad entries and continued during passage of the longwall panels on both sides of the entry. Monitoring included overcore stress measurements of the initial stress within the rock mass, changes in cable bolt loading, standing support pressure, roof deformation, rib deformation, stress changes in the coal pillar, and changes in the full three-dimensional stress tensor within the rock mass at six locations around the monitoring site. During the passage of the first longwall, stress measurements in the rock and coal detected minor changes in loading, while minor changes were detected in roof deformation. As a result of the relatively favorable stress and geological conditions, the support systems did not experience severe loading or rock deformation until the second panel approached within 30–50 ft of the instrumented locations. After reaching the peak loading at about two to three inches of roof sag, the cable bolts started to unload, and the load was transferred to the standing supports. The standing support system was able to maintain an adequate opening inby the shields to provide ventilation to the first crosscut inby the face, as designed. The results were used to calibrate modeled cable bolt response to field data and to validate numerical modeling procedures that have been developed to evaluate entry support systems. It is concluded that the support system was more than adequate to control the roof of the tailgate up to the longwall face location. The monitoring results have provided valuable data for the development and validation of support design strategies for longwall tailgate entries.

Jan 1, 2017

By Christopher Mark

Coal bursts are typically associated with highly stressed coal. Most bursts occur during retreat mining (longwall mining or pillar recovery) in highly stressed locations like the tailgate corner of the longwall panel. Others are associated with multiple seam interactions. However, a small but significant percentage of coal bursts have occurred during development or in outby locations unaffected by active mining. Most development bursts have been relatively small, but some have been highly destructive. No theory of coal bursts can be complete if it does not account for this type of event. This paper focusses on the development mining coal burst experience in the US, putting it into the context of the entire US coal burst database. The first documented development coal burst occurred almost exactly 100 years ago during slope drivage at the Sunnyside Mine in Utah. Sunnyside subsequently had a long history of bursts, mainly during retreat mining but also during development. Several Colorado mines have also experienced multiple development bursts. Some, but by no means all, of the development bursts in these western US coalfields have been associated with faults. In the Central Appalachian coalfields, most development bursts have occurred in multiple seam situations. In some of these cases, however, there was no retreat mining in either seam. The paper closes with some lessons from this history, with implications for preventing such events in the future.

Jan 1, 2017

By D. G. Lynch, M. R. Martin, R. J. Coutts

"Broadmeadow Mine is an underground longwall mine located in Central Queensland, Australia. The mine introduced a top coal caving (TCC) longwall face in 2013 but since then has experienced severe convergence events at the start of each panel after 60–70m of retreat, resulting in equipment damage and the longwall almost becoming iron bound. A significant geotechnical monitoring effort during LW10 and LW11 to characterise the caving mechanics and operational changes during LW11 were successful in mitigating the risk posed by these initial convergence events. This paper describes the geotechnical monitoring programme undertaken during LW11, the operational methods used to mitigate these initial convergence events, and the contribution to these events of the TCC technique.A thick sandstone unit close to the extraction roof was likely the cause of the convergence events at the start of each longwall panel. However, stress change monitoring cells, surface extensometers, an inclinometer, and the blockage of holes designed for pre-conditioning using hydraulic fracturing indicated that the convergence events were not caused by the sudden collapse of sandstone bridging across the goaf. Rather, they were caused by the propping action of strong units within the overburden strata. Equipment design modifications were made to allow the longwall to remain operational during the convergence events and an operational strategy was implemented to mitigate convergence in LW11. The initial convergence event was successfully negotiated, and Broadmeadow went on to be the highest producing longwall for CY16 in Australia.INTRODUCTIONBroadmeadow Mine is an underground longwall mine located in Central Queensland, Australia, owned and operated by BHP Mitsubishi Alliance (BMA). The mine is a punch longwall mine using open cut pit access provided by Goonyella/Riverside Mine. Broadmeadow commenced longwall operations in 2005 using a conventional high reach longwall, but later changed to the top coal caving (TCC) method of extraction. Broadmeadow extracts the easterly dipping 5.5–7.5m-thick Goonyella Middle Seam in ranging in depth from 90m to 330m. The coal is washed and blended at the adjacent Goonyella/Riverside open cut mine to produce a premium coking coal product for export."

Jan 1, 2018

By Bruce K. Hebblewhite

This paper provides an overview of the international ?state of the art? with respect to underground coal mining methods used in seams of thickness greater than 4.5 m, through a review of a selection of high performing thick seam mining operations around the world?both Single Pass Longwall (SPL) and Longwall Top Coal Caving (LTCC). The paper discusses the recent operational experiences from these selected faces, together with the ground control issues faced, and identifies some of the major, inherent geotechnical factors that can influence the mining method selection, design criteria, and ultimate performance, from both an operational and safety perspective. It is clear that both of these methods are developing quickly? not only from an operational and equipment perspective, but also from the understanding of critical geotechnical criteria. There is an increasing role for both methods in thick seam environments, although the higher SPL faces will only be successful in the near to mid-term under benign geotechnical environments. Regardless of the method, a thorough understanding of the critical geotechnical factors is a key to successful implementation of either method.

Jan 1, 2013

By Stephen Tadolini

The annulus thickness, for bolts anchored with resin, effects the systems final performance. Recent developments in the manufacturing process of these support systems, coupled with improved resin characteristics, have resulted in design changes to minimize hole drilling requirements and reduce resin usage. The amount of resin to properly anchor a 7/8-SRD (Special Rolled Dimensions) bolt in a 25.4 mm (1-in) diameter hole has been reduced to about one-third of the resin required to anchor a No. 7 rebar bolt (22 mm (7/8-in) diameter) traditionally installed in a 35 mm (1-3/8-in) diameter borehole. More importantly, laboratory and field tests, indicate that higher bond strengths and anchorage capacities can be realized with reduced annulus systems. These factors have a direct bearing on reinforcement efficiency and subsequent roof support performance.

Jan 1, 1998

By Thomas Lautsch

After a short description of geology and gateroad roof support technology in the German coalfields the development of roof bolting as primary roof support is presented. Based on geotechnical parameters, different strategies used for roof support at depths of 3,300-4,600 ft. are explained. Strict quality management and a strict monitoring program are part of the entry development. A number of recently finished developments are described such as the introduction of standardized bolts and accelerated resin systems. An outlook of future goals is presented. The paper concludes with a comparison of roof control systems at RAG's mines in the US and Germany.

Jan 1, 2000

By Michael A. Berdine

In early 1997, Twentymile Coal Company took a dramatic departure from traditional longwall recovery methods. Previously, Twentymile's standard longwall meshing procedure included the use of chain link fencing material. Beginning with the 9-Right to 8-Right longwall recovery operation, Twentymile incorporated a polyester geogrid mesh system supplied by DYWIDAG-Systems International. This paper discusses the subsequent utilization of the polyester geogrid mesh system at Twentymile.

Jan 1, 2001

By Houquan Zhang, Ming Li, Guimin Zhang, Bei Zhang

"The support quality of bolts in deep roadways is one of the important factors for efficient and safe coal production. A new kind of non-destructive testing technique and equipment was used to monitor the axial bolt load in real time in deep roadways. Based on the test results, the working status of bolt support in deep roadways was evaluated. The research results show that the variation characteristics of axial bolt load is consistent with the distribution characteristics of rock pressure no matter whether it is in the initial support stage or mining disturbance stage. The axial load of bolts located 20m outby the development face has an overall rising trend within 3-5 days after installation. Within a certain distance in the front abutment pressure zone in front of the face, the axial bolt load increases with the advance of coal extraction. When coal and rock in the abutment pressure zone yield, the axial bolt load is dropped correspondingly. This kind of non-destructive testing technique provides an advanced means of detection and evaluation on bolt support quality.INTRODUCTIONMany coal seams more than 800m deep are being mined in eastern China. Roadways of large cross-section are being developed in coal seams more than 600m deep in western China (Kang et al. 2014). Moreover, these roadways are commonly supported by roof bolts and have encountered many support problems, including soft rock strata, intense mining disturbance, and abnormal tectonic stress. The stability of its surrounding rocks is difficult to maintain, the roof bolt even fails before mining (Shen 2014; Jiang et al. 2015). Therefore, it is very important to develop an effective method to detect the bolt quality in real time and evaluate the bolt's safety status.During installation of roof bolt, the installation quality is heavily affected by installation equipment and tools, field conditions, and operators' skills (Li et al. 2005; Shan 2009). The anchorage length will be shorter than the designed one if the resin cartridges are pushed to the bottom of excessively long drill hole and stay there without being shredded and mixed. The support function of the bolt would be weakened by the shorter anchorage length."

Jan 1, 2016

By Xuexin Ding, Weijie Wei, Jinwang Zhang, Yi Chen, Shengli Yang

"Many ultra-thick coal seams exist in Xinjiang and the northern part of the Inner Mongolia. These coal seams are more than 30-40m thick. This kind of the thick coal seam is too difficult to extract in one slice, so the top-coal caving longwall mining method was designed for this purpose. In order to study the movement characteristics of the overburden strata and the development of the ""three zones"" in ultra-thick coal seams, the physical and numerical simulations were carried out based on the in-site condition of Baiyinhua coal mine. The result shows that, when extracting the upper part of the l 5m thick coal seams, the first weighting interval was 50-58m and the periodic weighting interval was I 8-20m. The caving zone, fractured zone and bending and sinking zone were 38m, 92m, and 50m respectively in height. The fractured zone height increased with the advancing distance of the face, but in some localities, a ladder-like distribution due to the periodic weighting existed. When extracting the lower part of the 25m thick coal seams, the roof was extremely broken and the collapse range of overlying strata continued to increase in irregular form.INTRODUCTIONThe thick coal seams occupy 44 percent of coal reserves in China and account for 45 percent of the gross domestic coal production. There are three main methods for extracting the thick coal seams: sublevel mining, large height mining, and longwall top-coal caving (LTCC) (Wang, 2009). Due to the rapid development of LTCC in the past two decades, it has become the most extensively used mining method. It possesses the advantages of high-production, high-efficiency, low development ratio, and low-cost (Yang, Zhang, Chen, and Zhengyang, 2016; Wang and Zhang, 2015). Baiyinhua coal mine's coal reserves are full of uniformly distributed thick coal seams, with the minable thickness of the main coal seam between 25 to 40m, i.e. the main coal seam is an ultra-thick coal seam. Sublevel longwall top-coal caving (SLTCC) which is an efficient method for extracting the ultrathick coal seams has led to multiple disturbances Xie, Chen, and Wang, 1999; Singh and Singh, 1999; Xie, Chang, and Yang, 2009. Therefore, using the case of Baiyinhua coal mine, the movement features of overburden strata and development characteristics of the three zones in ultra-thick coal seams were studied by physical and numerical simulations (Qian, et al, 2003; Qian, 1994)."

Jan 1, 2016

By C. Fairhurst

Most of the papers designated as being within the topic of underground storage at this Symposium are concerned with aspects of radioactive waste isolation. Although this is, unquestionably, an important international application of underground storage, and one involving a considerable number of research investigations, the subject of underground storage is indeed much broader. Several major international conferences have been devoted exclusively to it. Applications include storage, under a range of temperatures and pressures, of oil and liquefied petroleum products, compressed air, heat, foodstuffs of various kinds, hazardous and 'nuisance' industrial by-products, and a variety of special applications, both civilian and military - some in use, others proposed. Storage may be in caverns excavated specifically for the purpose, exhausted mines may be adapted for storage or, in some cases, the material to be stored may be injected under pressure into the pore spaces of porous-permeable formations at depth. A variety of rock types and geological environments are used, e.g. excavations in salted or domal salt, where long-term creep closure of the openings is a concern; massive granite, where fluid loss through fissures may be important. Cavities may have spans of several tens of meters, and there is interest in achieving still larger excavations. As would be expected, this breadth of underground storage applications introduces a similarly broad range of questions in rock mechanics and rock engineering. The report will review these questions and recent developments in rock mechanics research, computational procedures, and design applications - and will also discuss the opportunities for a still greater range of applications of underground storage to current industrial and social problems.

Jan 1, 1989

By Tony Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and Laurel Hill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereonet, and rose diagram projections so that the Loyalhanna's structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts. pillar sizes, etc., that lessen miner exposure to these hazards.

Jan 1, 2002

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Alan Campoli

Approximately 100 million fully grouted rebar roof bolts are installed each year in the United States, 80% are B-Series (5/8 inch fully grouted rebar in a one-inch borehole). The lesser used more expensive A-Series (3/4-inch fully grouted rebar in a one-inch borehole) maximizes resin performance. Standard B-Series provides only 60% of the pull out resistance of A-Series. The Eclipse System was developed by Minova USA Inc. and marketed with Excel Mining Systems to improve the performance of B-Series. A 1/8-inch offset bolt head combined with a specially formulated Eclipse Lokset resin cartridge results in increased mixing efficiency and more uniform resin anchorage. Over two million units have been sold to date; the majority of these Eclipse bolts have been sold to coal mines in the Illinois Basin. Pull testing has demonstrated that a Grade 60 Eclipse bolt provides equal or superior pullout resistance as compared to a Grade 40 No. 6 rebar. Short encapsulation pull tests have yet to consistently demonstrate the superior pullout strength of Eclipse to standard B-Series, however 12 inch Eclipse grouted columns have successfully held in excess of the bolt yield load. The successful substitution of Eclipse bolts for A-Series has significantly reduced the primary roof support costs by approximately $0.18 per foot of bolt. Recent over coring analysis of various anti-gloving methodologies performed in New Zealand has confirmed the superior mixing of the Eclipse system (5).

Jan 1, 2004

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989