Search Documents

By Alexandra Garcia

A measurement-based ground control management system, commonly employed in coal mines, has been successfully implemented in a UK potash mine operating at a depth of over 800 m. This system includes the routine deployment of telltales in roadways throughout the mine to mitigate against the risk of large-scale roof falls and the deployment of detailed ?design monitoring? instrumentation for ongoing design verification. The routine monitoring systems used in coal mines have not been, to date, commonly applied in potash mines, despite the similar, variable weak geology and associated ground control hazards. Monitoring information from the site indicates that telltales can be deployed to monitor roof conditions, with action levels based on differential rates of strain, as opposed to absolute movement.

Jan 1, 2014

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By Vincent A. Scovazzo

The Pennsylvania Joint Coal and Gas Committee Gas Well Pillar Study of 1956 is the bases for well protection pillar design in the US and many other countries. An update was necessary because the well construction common to the gas and coal industries as well as mine configurations, mine depth, and extraction thickness have changed considerably since 1956. As initially envisioned the update would involve a similar empirical study that formed the basis of the initial investigation. However, there are no records of any gas or oil well failures related to coal mining since 1956 when mines followed the initial recommendation, making an empirical study problematic. Thus, the study had to be more analytical, which in return required at least some fundamental research into the behavior of the interaction of coal mining and oil and gas wells. A call to industry about research they have undertaken resulted in obtaining excellent research on the subject from three companies; Alpha Natural Resources, Inc., CONSOL Energy Inc., and Range Resources. These research projects were initially undertaken for internal use and not previously published. John T. Boyd Company reanalyzed these studies and determined how their results would affect protective pillar designs. These research projects pointed to the importance of horizontal movement and shear caused by subsidence and the strength of pillars and their foundations. The importance of geology is important in understanding horizontal shear, ground movement, and floor strength. The failure modes of casing and pipe needed to be understood so the threshold of these movements and stresses could be determined.

Jan 1, 2013

Effective strata control, utilising fully encapsulated roof bolts, is dependent on the installed quality of the reinforcement elements. One mechanism by which fully encapsulated roof bolts may become less than fully effective is by gloving (glove fingering) and un-mixing of the resin. Following some small roof failures containing gloved bolts, investigations have been undertaken in some New Zealand coal mines to determine the extent of, and mechanisms involved in, the gloving of fully encapsulated roof bolts for a range of roof types and installation methods. Gloving, in this context, refers to the resin cartridge partially or completely enveloping a length of the bolt, typically with unmixed resin filler and catalyst/hardener remaining within the cartridge. Results have shown that gloving and un-mixing is a systematic and widespread phenomena, occurring across a range of resin and/or bolt manufacturers, and across a variety of roof types. Gloving was found in bolts installed using: hand held pneumatic and continuous miner mounted hydraulic methods, under run of mine (ROM) conditions by mine workers, and under controlled "best practice" conditions. The roofs bolts investigated are all 1800mm (6ft) long, and have shown that, on average, 485mm (-19") of the bolt length is gloved and/or unmixed. This equates to a 27 percent reduction in effective bolt length. The effected length of bolt is sufficient to impact on the load transfer/reinforcement capabilities of the bolt system, and hence impacts on the design assumptions and subsequent stability assessments. Furthermore, there is a direct relationship between the mechanism for the gloving of bolts and an increased occurrence of resin loss and reduction in encapsulations length in soft (less than 10 MPa) and/or highly fractured rock. Investigations have concentrated on developing an understanding of the mechanisms involved. This has been undertaken using both field installations and recovered bolts, as well as test bench trials. The mechanisms involved have been confirmed as being: the development of a pressure front as the bolt encounters the resin and is spun up the hole, which, in turn, leads to over-pressurisation and radial expansion of the resin cartridge, resulting in an increase in diameter of the plastic resin cartridge, which allows the bolt to be spun up into the cartridge without making sufficient contact to shred the cartridge or the hardener tube, resulting in an unmixed portion of resin.

Jan 1, 2003

By David Bigby

Rock Mechanics Technology has developed an intrinsically safe remote reading telltale system which allows up to 4 sets of 100 dual height, water diverting telltales in a mine roadway to be remotely monitored from a surface PC. The system has US MSHA approval and European ATEX approval for use in gassy mines. A successful full-scale application of the system employing 67 telltales was completed in a 1300m long maingate roadway during retreat of 183.0 longwall panel at West Mine in Germany between June 2001 and October 2002. During panel retreat a number of "teething" problems associated with the system were identified and resolved, the chief problem being associated with cable connection corrosion due to the unforeseen use of sprayed calcium chloride in the roadway. This paper describes the experience of employing the system at the colliery from the perspective of both the user and the manufacturer, and the improvements and developments which have resulted. The paper also presents examples of roof movement data recorded by the system, including data from behind the retreating longwall. The high resolution and data recording rate possible has resulted in particularly interesting information on roof behavior within the longwall front abutment area and behind the face. The paper also describes a series of new transducers and extensometers for the mining industry which employ the same physical principles and similar electronics to the remote reading telltale system. These have been applied in a variety of mining and tunneling environments worldwide over the last two years.

Jan 1, 2003

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By Timothy J. Matthews, Timothy J. Batchler, Ted M. Klemetti

"From 2011–2016, there were 1,511 documented injuries, including 7 fatalities, from ground falls in underground coal mines in the United States. The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in Pittsburgh, PA.The load-displacement characteristics of an 8-ft x 12-ft panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of varying the number and position of the load pull location on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines.INTRODUCTIONThe large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in Pittsburgh, PA."

Jan 1, 2018

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010

By L. R. Stace

Arguably, one of the most significant technological breakthroughs that had been experienced during the period when British Coal was the major coalmine operating company in the UK, the use of rockbolts as principal support in underground roadways brought with it the need to re-assess the technical knowledge, management controls and legislative frameworks associated with the support of mine workings. Following a major roof fall in a roadway supported principally using rockbolts in which fatalities occurred, the process of the design of rockbolted support and the systems and procedures that had been put in place to control its use in the UK were further reviewed. The paper discusses the outcome of these reviews, and how the incident initiated a major new interest in strata control research in the UK against the background of the fragmentation of the ownership of the mines following the sale of the former British Coal assets at the end of 1994, together with the proposed introduction of new strata control legislation in 1996.

Jan 1, 1996

By G. R. Corbett

The introduction of roof bolts to Phalen Colliery in the Sydney Coalfield, Nova Scotia (annual output of 2Mt) has been successfully implemented in maingate and tailgate entries over the last four years. Monitoring of the roof bolted areas continues to be an integral part of the quality control program as the results are utilized to maintain safety and to aid in long-term design strategies. Although all gateroads in the Phalen Colliery have converted to roof bolts as their primary means of support, the majority of intersections which intersect the main slopes remain supported by large steel structures. Several intersections within the Phalen Colliery were monitored as they were created by the mining process. A comparison is made between intersections supported with only traditional 6.4 to 6.7 m steel structure and intersections supported by 2.44 m fully resin encapsulated roof bolts in conjunction with 7.6 m fully cement grouted cable bolts. Detailed monitoring was conducted using CA NM ET's intrinsically safe sonic probe extensometer datalogger which has the ability to read up to sixteen probes simultaneously at programmed intervals. The density of the data from the datalogger has allowed a better understanding of the deformation of cable bolted intersections than was possible with manual monitoring. Test results have helped mine operators to design safer cable bolted intersections.

Jan 1, 1995

By Yuanping Cheng, Jingyu Jiang, Qiang Zhang

"With the increase of mining depths, deep-seated coal seams face threats from high ground stresses, high gas pressures, high gas content, and low seam permeability, which significantly increase the likelihood of coal and gas outbursts. Challenges continue to grow in coalbed methane (CBM) extraction fields, especially for short-distance gassy multiple-seams. Research has proved that the most effective way to increase coal seam permeability is to decrease the ground stress. Protective seam mining technology is a surrounding rock control technology, which can effectively reduce the ground stress and increase the permeability of the protected coal seam. In this paper, we try to use upper protective seam mining technology to simultaneously extract coal and gas. Findings are based on a FLAC3D simulation of stress variation during the mining of the No. 12 coal seam in the Daxing coal mine, Tiefa Coalfield, China. Results indicate that, after mining the upper protective seam, the pressure-relief effects of the rock mass generated three belts and five zones below the protective seam, providing the space and time for gas pre-extraction engineering. Within the protected area, the numerical simulation indicates that the stress of the No. 13/14 coal seam reduces 95.84% and 88.25% respectively, while the expansion deformation of the protective seams reach 6.87 ‰ and 6.70 ‰ respectively, which demonstrate that the protective mining technology can provide a significant pressure-relief effect to the outburst-prone coal seam. Combining stress relief in this manner with pressure-relief from engineered gas drainage (performed by crossing boreholes from the floor rock roadway) applied before the mining of the protective seam, it would not only be beneficial to CBM drainage but also can reduce the gas outburst risk of the protected seams.INTRODUCTION Internationally, since France used protective seam mining technology to control coal and gas outburst in 1939, it has been promoted and applied in many countries (?????, 1966). Since 1958, China has taken the mining test and engineering practice of protective seam mining technology in the Beipiao, Tianfu, Nantong, Zhongliangshan, Songzao, Huainan, Huaibei, and other coalfields (Yu, 1992). Long-term theoretical research and mining practice of outbursts and dangerous coal seams show that protective seam mining technology is the most effective, safest, and most economical outburst prevention measure (Cheng, Fu, and Yu, 2009; Hu et al., 2008; Cheng and Yu, 2007). Under the condition of high gas content coal seams, the safety and efficiency of simultaneous extraction of coal and gas can be realized through a reasonable mining sequence and an effective gas extraction method (Cheng and Yu, 2003). The in situ stress distribution of the protective seam (No. 1 coal seam) and protected seam (No. 2 coal seam) during protective seam mining in the Haishiwan coalfield formation (Figure 1) (Li et al., 2014). A comparison of the stress and displacement (five zones and three belts) of the rock mass below the protective seam, and in a multiple-seam context in the Dalong Mine, is shown in Figure 2 (Jiang et al., 2015). After mining protection coal in a close-distance seam group, the small spacing between the coal seams causes the protective coal and the protected coal between part of the rock to crack through each other until the protective layer of gob is through the area. This provides a desorption of gas to the protective layer of the mining space channel, making the coal seam permeability increase to several hundred times and improving the gas discharge capacity (Zhai, 2008)."

Jan 1, 2017

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

By Eric Zahl

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an ongoing effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for imple¬menting a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. How¬ever, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

Jan 1, 2002

By Ximeng Li

The entries that are subjected to dynamic pressure are much more difficult to maintain due to repeated disturbance. A case study of an entry stress distribution was performed using the FLAC3D program. By analyzing the distribution of stress field around the entries, this paper provides guidelines for entry support design in the lower (#16) seam subjected to the repeated disturbance from longwall mining in the immediate overlying (#17) seam, 72ft (22 m) above. The results showed that there was stress superposition inside the barrier pillar in the lower seam, 15ft (5m) to 45ft (15m) deep, during development. The influence zone of the front abutment pressure in the upper (#16) seam was about 100ft (30m) outby the faceline. The stress-relieved zone was from 0 to 100ft (30m) inby the face. The area further inby the face (i.e., 230 ft (70 m) inby the face) was within the gob compaction zone. Along the face advancing direction, the affected zones of the entries in the lower (#17) seam that were subjected to the dynamic pressure from longwall mining of the immediate overlying seam could be divided into four stages: pillar development stress stage, front abutment pressure stage, unstable gob stage, and stable gob stage. Those entries within an area from 100ft (30m) outby to 100ft (30m) to 230ft (70m) inby the faceline should be reinforced with special supports. The numerical modelling matched the monitoring results well.

Jan 1, 2013

By Kristine L. Pankow, Keith D. Koper, Michael K. McCarter, Jared R. Stein

"The Wasatch Plateau region of central Utah contains a number of active underground coal mines in an area of well-documented natural seismicity. As a result, there are several hundred seismic events recorded in this region every year that may or may not be attributed directly to mining activity. Previous studies have linked the majority of this seismicity to mining activity through various means, but have not attempted to develop a method for categorizing individual events within a seismicity catalog. This study uses both relative relocation and waveform cross-correlation to separate events based on hypocentral depth and waveform similarity, respectively, in the area surrounding a single longwall coal mine within the Wasatch Plateau. We conclude that relative relocation can help with depth discrimination, but there are some unavoidable limitations caused by sparse seismic network coverage. The cross-correlation technique is more promising, with the ability to group events by waveform similarity and track mining progress over both space and time. With cross-correlation based clustering, we confirm that the vast majority (97.6%) of events in the study area are directly related to mining activity, but that a small population of natural seismicity is present as well. Eliminating this natural seismicity from the catalog of seismic events, leaving only those events related to mining, can give operators valuable information about the changing conditions as mining progresses and eliminate concern over events unrelated to mining activity.INTRODUCTIONA number of underground coal mines are located in the Wasatch Plateau region of central Utah, and have been in operation since the late 1800s. This activity has resulted in a well-known history of mining induced seismicity (MIS) (Wong, 1985). Additionally, this area is situated near the border of the Basin and Range and Colorado Plateau physiographic provinces, where naturally occurring tectonic earthquakes also occur (Arabasz et al, 1980). Seismicity separating these physiographic provinces is part of a larger band of seismic activity known as the Intermountain Seismic Belt (ISB) that runs from Montana to Arizona and cuts through the western boundary of the central Utah coalfields (Smith and Arabasz, 1991) (Figure 1)."

Jan 1, 2015

By Elizabeth Holley, Meriel Young, Gabriel Walton

"The coal mine roof rating (CMRR) was developed by Chris Mark and Greg Molinda to bridge the gap between geological variation in underground coal mines and engineering design. The CMRR accounts for the compressive strength of the immediate roof, the shear strength and intensity of any discontinuities present, and the moisture sensitivity of the immediate roof. The CMRR has been widely used and validated in Eastern US coal mines, but it has seen limited application in the Western US.This study focuses on roof behavior at a Western coal mine. Mine A shows significant lateral geological variation, along with localized faulting and a laterally extensive sandstone channel network. The CMRR is not used to predict roof instability at the mine.It is, therefore, hypothesized that there are other factors that are correlated with roof instability in underground coal mines that could potentially also be included in the CMRR.This hypothesis was tested by collecting 30 CMRR measurements at Mine A. At each measurement location, a binary record of the roof condition (stable or unstable) was made along with parameters, such as depth of cover, thought to also correlate with roof stability. A statistical analysis of the data was performed to determine the parameters in addition to those included in the CMRR, which can be correlated to roof stability.INTRODUCTION AND BACKGROUNDRoof fall is one of the greatest hazards facing underground coal miners (Barczak et al., 2000). In 2017, 91 lost-time injuries occurred due to roof fall in US underground coal mines. A further 48 roof falls occurred with no lost days (MSHA, 2018).The coal mine roof rating (CMRR) classification was developed by Molinda and Mark (1994) to quantify the geological description of mine roof into a single value that could indicate mine roof stability and be used in engineering design. It is widely used in the Eastern US as an input for the analysis of longwall pillar stability (ALPS) in underground coal mines. It provides an excellent start; however, it is arguably not fully comprehensive, nor is it widely used in the Western US."

Jan 1, 2018

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

By Gregory E. Smith

"Tensionable headed roof bolt systems are common in the U.S. mining industry. In the last 15 years or so, they have made a comeback as a hybrid system where a mechanical anchor is used in conjunction with resin. When such a system is used, it is common to use a spherical washer to comply with the requirements of 30 CFR Part 75.204(f)(8). This standard requires an angle-compensating device be used in installations where the bearing plate is offset from the roof bolt axis by an angle greater than five degrees. This paper evaluates system performance of four different traditional angle-compensating device/plate combinations including a new patented extruded plate/extruded washer system that improves overall load capacity and stretch.INTRODUCTIONA large western U.S. underground coal mine was using a fully grouted headed rebar system as their primary support. They had developed their component specifications over many years of working with suppliers to improve and optimize these components to integrate well as a system. As shown in Figure 1, the components included a patented 7 /8"" -diameter Grade 60 headed rebar bolt with a flange capable of full bar load (Walker, 2009) and a patented 8 in x 8 in Grade 3 extruded hole bearing plate manufactured by DieMatic Corporation.The mine decided to pursue a fully grouted tensionable system using a mechanical anchor as the tensioning device. Their primary goal was to eliminate the need for the roof bolt operator to secure (hold) the bolt during resin set time. An additional benefit was the increased initial tension on the bolt. To comply with the requirements of 30 CFR Part 75.204(f)(8), regarding tensioned roof bolts, they were required to include an angle-compensating device because a share of the bolt population would be installed at angles greater than five degrees from the perpendicular to the bearing plate. Also, to improve cycle time and torque/tension consistency, the mine desired to have the washers and anchors assembled at the factory. This required the use of a bearing plate with a center hole large enough to accommodate the 1-3/8-in-diameter mechanical anchor to pass though it during assembly by the roof bolt operator. The mine wanted to continue to use an extruded hole bearing plate in the tensionable system, and EMS was asked to propose a plate and angle-compensating device."

Jan 1, 2016

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992