Search Documents

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By Anthony Spearing

There are approximately 68 million rockbolts installed annually in underground coal mines in the USA (Tadolini and Mazzoni, 2006). The most utilized is the passive fully grouted resin rebar bolt, which constitutes almost 90% of the primary support in US underground coal mines. Resin-grouted rockbolts are a very effective and safe support, but their performance still needs to be further optimized and improved. This paper investigates their performance and suggests operating conditions to optimize the performance of resin-grouted rockbolts. In addition, this paper discusses a small-scale test that can also be used to evaluate the performance of rockbolts that is quicker, easier, and less costly than short encapsulation tests.

Jan 1, 2014

By Anton Sroka

The dimensioning of shaft safety zones is a substantial task of mining subsidence engineering. On the one hand, the coal reserves in shaft proximity are to be mined as complete as possible, because they can be made accessible economically. On the other hand, the maintenance of the shaft operation is to be ensured at each time, since shafts represent the most important link between underground and aboveground. Regarding these two criteria, this publication presents a model for the optimization of shaft safety zones. Beyond that, extraction methods in shaft safety zones are described, in particular with consideration of minimized mining influences on the shaft.

Jan 1, 2005

By Brian E. Travis

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to steel. The finished polymer mining grid product is a viable alternative to conventional supplemental roof control meshes such as chain link fence and welded wire. Polymer mining grids are a fraction of the weight, have comparable load support qualities, and will not rust or corrode in even acidic or alkaline conditions. Specific flame retardant additives can also be incorporated to make the polymer grid self extinguishing for use in underground "gassy" environments.

Jan 1, 1992

By Jim Galvin

4 and 6 point timber chock constructions are used extensively on both a systematic and spot basis by Australian longwall operators to support tailgate roadways. In 1996, the School of Mining Engineering at UNSW published design and performance criteria for timber chocks constructed from Australian hardwoods. The research was funded by the Australian Coal Association Research Program (ACARP). In 1997, ACARP awarded funding for a stage 2 testing program. This testing focussed on examining the effect of using thinner timber elements in chock constructions to improve OH&S and comparing the full-scale performance of traditional 4 point chocks to Link-n-Lock constructions. It was established that chocks constructed from thinner elements have failure loads much less than thicker elements. However up to the failure loads of the thinner elements there was no significant difference in the response to convergence of chocks constructed from 25, 50 or 100mm thick elements. Chocks constructed from 150mm thick elements have a similar ultimate strength to the 100mm thick elements. However, they have a significantly lower resistance to load, thereby permitting more convergence to occur. There is more potential for chocks comprised of thin elements to be constructed 'out of plumb' and so suffer eccentric loading. The full scale testing program established that at any given level of convergence up to 10% strain, the timber in a Link-n-Lock chock generates twice the support resistance of the same quantity of the same timber in an equivalent size 4 pointer chock. On the basis of support resistance per cubic metre of timber, there is only a marginal difference in the performance of 1.0m Link-n-Lock chocks and 1.2m Link-n-Lock chocks constructed from select Blue Gum. The cost per tonne of support provided by a Link-n-Lock chock is effectively half of that provided by a 4 pointer chock of equivalent dimension and timber. Up to a strain level of 4%. Link-n-Lock chocks constructed from 1.2m long elements are slightly more cost effective than the same chocks constructed from 1.0m long elements. Thereafter, there is no significant difference in cost per tonne of support resistance. Beyond a strain level of about 4%, Link-n¬Lock chocks constructed from landscape grade Blue Gum are just as cost effective as Link-n-Lock chocks constructed from structural grade 4 Blue Gum.

Jan 1, 2000

By Thomas M. Barczak

A survey of the longwall industry was conducted to examine the performance of modern shield technology. The results of this survey indicate that state-of-the-art shields perform better and last longer than ever before, but premature failures do still occur. In addition, longwalI operators are now using shields longer than ever before and a greater number of fatigue related failures on aging shields are now occurring. A generic assessment of these shield failures is provided, describing the nature of the failures and how widespread they are throughout the industry. An engineering assessment of shield design and factors that cause shield failures is made using both strength of materials and fracture mechanics principles. From this analysis, design practices to improve structural margins of safety and extend the life of the shield are proposed. The existence of unexpected shield failures indicate that current shield performance testing is at times inadequate. Recommendations are made relative to improved shield performance testing protocols including the benefits of testing in an active load frame such as the National Institute for Occupational Safety and Health's (NIOSH) Mine Roof Simulator. Even the most rigorous shield testing procedures, which strive to simulate in-service loading conditions, fail to consider key environmental issues, such as corrosion which is often the cause of structural fatigue failures in modern shields. The survey also indicated that hydraulic failures occur much sooner in the life cycle of a shield than structural failures, and although they can significantly degrade support capability, often go undetected for long periods of time. Methods to detect the hydraulic failures are also provided. The paper concludes with key points to maximizing shield design and life expectancy and ideas for future generation shield designs.

Jan 1, 1999

Tailgate pillar and tailgate-face corner humps have been a major threat to longwall coal mines where hump-prone conditions exist. The yield pillar design concept, in which the longwall chain pillars are designed in such way that they can yield in a nonviolent or controlled manner during longwall retreat, has been used in many longwall mines to prevent tailgate pillar humps. However, this practice often shifts the side abutment load onto the tailgate-face corner especially when a massive and strong sandstone member is present within the caving zone or in the vicinity of the coal seam. Therefore, the abutment pillar design concept has also been used in some hump-prone coal mines to minimize the stress concentration on the tailgate panel rib for the control of tailgate-race corner humps. The disadvantage of using the abutment pillar design concept is that it is more costly and puts additional pressure on mine operations for gate entry development and significantly reduces the recovery of coal reserve. In addition to pillar size, panel layouts. such as the panel width and panel orientation also play a critical role in pillar or face humps and should he taken into account. Based Upon the Cyprus mine design and operational experiences at Willow Creek and case studies at other bump-prone longwall nines in the U.S., the authors attempt to identify the critical factors causing coal mine bumps and to introduce some guidelines and criteria for the design of both yield and abutment pillar systems and panel layouts.

Jan 1, 1999

By B. (Mamas) Das

A project to evaluate the suitability of point Load strength tests for testing and classifying coal measure rocks for coal mining application was initiated by Canada Centre for Mineral and Energy Technology (CANMET). A summary of this study with emphasis on the important findings is presented in this paper. The instrument as used in this study is a Robertson Research Rock Strength Index Log. Because of the variation in the correlation ratio between uniaxial compressive strength and point Load strength index for hard rocks and soft rocks it was decided to establish this corre¬lation initially on cement concrete specimens specially prepared for this purpose following ASTM specifications. These specimens are expected to represent soft rocks and at the same time would be of uniform quality. Once a general trend of this correlation was established tests were performed on coal and rock samples from the sub-bituminous and bituminous coalfields in Canada. The most important results may be stated as follows: (i) Generally, the common value of the ratio between the uniaxial compressive strength and the point load strength index ranges between 8 to L4. (ii) The Robertson Research Rock Strength Index Log proves to be quite suitable for testing sandstone, siltstone and some coals from the bituminous coalfields but problems have been experienced when testing weathered samples or samples from the sub-bituminous coalfields. (iii) In some cases tests were successful if Larger samples from weathered zones or from sub-bituminous coalfields were used. However, a magnified load gauge for 0-3KN or 0-5KN is expected to be the best solution for soft and weathered rocks in most of the cases. Some mudstones and some rocks from weathered zone do not appear to be suitable for these tests. This aspect of the study is still under investigation. (iv) Deterioration of rock properties due to weathering has been determined through tests on samples collected from weathered and unweathered samples.

Jan 1, 1984

By Luis Giraldo

Rock bolt installation characteristics near roof falls have been identified as contributing to failure. One documented and regularly occurring failure mechanism is loss of anchorage between the grout and the rock wall of the bolt hole. Key contributors to the integrity of the grout interlocking with the rock mass are the diameter of the hole relative to the diameter of the bolt, resin versus cement type grouts, rock type, and condition of the hole. Smooth bolt holes consistently exhibit less rock bolt load bearing capacity than rough walled holes. The goal of this study was to quantify the benefits of borehole conditioning and develop a systematic approach that would allow improvement of roof bolt performance. A new rock drilling technology, the Helical Drag Bit (HDB), was used in the early stages of this project to condition the borehole. The HDB cuts a prescribed helical groove in the borehole wall. When a bolt is grouted into a hole that has been conditioned using the HDB, the grout fills the helical groove and provides a stronger, more reliable mechanical lock between the rock and the grout. This paper presents results of a series of tests conducted in the laboratory and in the field. Short encapsulation pull out tests have demonstrated considerable increase in pull out strength and more consistent bolt performance when hole geometry is modified using the HDB. The results have also shown that greater load bearing capacity improvements are obtained in mines with weak roof rock, where it is most needed. Additionally, bolts recovered for examination suggest that hole conditioning during roof bolting reduces the effects of finger gloving. Therefore, mines with stronger roof rock could also benefit from hole conditioning. A new roof bolt that uses the HDB principle has been designed and tested. The new system works with existing bolting equipment requiring minimal modifications to the traditional procedure used for installation of fully grouted rebar bolts. The use of these higher anchorage capacity bolts will allow mines to reduce severe injuries and fatalities resulting from ground failures while maintaining or increasing productivity.

Jan 1, 2005

By Neil Styler

This paper presents an analysis of measurements of inter-burden de- formations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock ex- tending to approximately 50 times the extraction height above the seam.

Jan 1, 1984

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

By Keith Heasley

As part of the initial investigation and validation of a new boundary-clement formulation for stress modeling in coal mines. the underground stresses and displacements at two multiple-seam coal mines with unique stress problems are modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and non-linear seam materials can he used: and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geo-mechanics based on previously observed stress conditions at the mine. For this calibration process. a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems abead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses, and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 1, 1998

By Gang Ren, Behrooz Ghabraie

"Observational data suggest that the ground surface subsidence profile from multiple-seam longwall mining is rather different from that of single seam. Despite the increase of coal production from multiple-seam mining, available predictive methods are mostly unable to predict a reliable subsidence profile for multiple-seam extractions. In this paper, a case study of multiple-seam subsidence is modelled using physical modelling techniques. The subsidence mechanism as revealed in the physical model is explained and the differences between multiple and single-seam subsidence are highlighted. On the same case study, a commonly used influence function method (IFM) and Generalised Influence Function Method (GIFM) are utilised to predict the subsidence profile. The results are compared with predictions achieved by a newly developed predictive method based on the understanding of mechanism of the multiple-seam subsidence. Results show a significantly improved correlation between the newly developed method in comparison with the conventional IFM and GIFM. INTRODUCTIONField observations and subsidence monitoring data from multiple-seam coal mining cases show a different subsidence profile as compared with single-seam ones (Sheorey et al., 2000; Li, et al, 2007; Luo and Qiu, 2012; Unlu et al, 2013). The multiple-seam subsidence curve is generally deeper and steeper than of single-seam cases, and varies from one mining configuration to another. Various researchers had made efforts to understand the mechanism behind this phenomenon and the interaction between the two mining horizons (Li et al., 2010, Sui et al., 2014; Zhang et al., 2014). However, the mechanism of the multiple-seam subsidence is yet to be comprehensively understood (Suchowerska, 2014; Ghabraie et al., 2015b).In addition, differences between the single and multiple-seam subsidence profiles make it difficult to adapt single-seam subsidence prediction tools for predicting the subsidence over multiple-seam cases, unless significant modifications are applied This requires understanding the mechanism of the multiple-seam subsidence as the first step to achieve reliable predictive results.The mechanism of the subsidence due to a multiple-seam case study can be investigated via physical modelling. The physical model allows observing the substrata movement as well as the interaction of the two mining activities. An understanding of the mechanism of the multiple-seam subsidence can be developed based on these observations, which would provide basis for developing a subsidence prediction tool."

Jan 1, 2016

By Jinsheng Chen

To maintain the stability of longwall tailgate entries, they have to be supported by not only the primary roof support but also the secondary roof support due to the impact of the longwall mining¬induced abutment loads. Depending on the mining condition of a typical coal seam and its distance from the previous panel's gob, the longwall tailgate entry is often reinforced by the secondary roof support in the form of standing supports and/or cable bolts or trusses during longwall retreat, Even though lots of research work has been done to study the behavior of different standing supports in the laboratory. their function and requirements for a typical mining condition are still not fully understood due to lack of field data and correct assumptions about the behavior of the already-bolted entry roof under mining-induced abutment loads. Therefore, the application of the secondary roof support for tailgate entry roof control is still limited to trial and error, which often results in either higher cost for tailgate roof control if the design is too conservative or more production delays due to roof falls in the outby tailgate entry if the design is inadequate. To have a better tailgate roof control with reasonable roof control cost, RAG American Coal, NIOSH, and HeiTech have been conducting a joint research project to monitor actual roof loading, roof deformation, and entry convergence in the tailgate entry of 10 North panel at RAG Emerald mine. The actual roof loading data are used to calibrate and improve the roof control model for longwall tailgate entries, which has been developed by RAG American Coal, and to further reduce the roof control cost for longwall tailgate entries. The authors in this study attempt to discuss the Roof Control Model developed by RAG American Coal. in which some guidelines or important parameters for designing the secondary roof support for longwall tailgate entries are proposed.

Jan 1, 2003

By Kevin M. Connor, O&apos

An example application is presented in which Time Domain Reflectometry (TDR) was utilized to monitor roof strata movements during pillar extraction in a potash mine. The study was initiated when Western Ag-Minerals decided to implement secondary mining of pillars in order to extend the life of their Nash Draw Mine. A prototype operation was conducted in one mine panel to assess mining equipment and procedures, and to determine if ground control problems would develop. An instrumentation array was installed by personnel from New Mexico Tech and Western Ag to monitor strata movements, changes in pillar stress and surface subsidence, and these data are being analyzed by the Bureau of Mines. This paper is limited to a discussion of roof-floor convergence and roof strata movement to illustrate the application of TDR to ground control. Plots are presented which demonstrate the capability of distinguishing location, magnitude and mode of rock movement using TDR to interrogate coaxial cables grouted into holes drilled in the roof.

Jan 1, 1990

By J. G. Stewart

Polyurethane injection for the consolidation and control of broken strata is a common practice in the deep mines in Europe. The technology has gained wide acceptance in the coal mines of America since the introduction of RokLok polyurethane binder by Mobay Chemical Corporation in 1977. A popular and growing use for polyurethane consolidation grouting is to control the roof and prevent gob flushing during recovery of longwall face equipment. The technique provides many time and performance-related benefits compared to more conventional methods using wire mesh. Kitt Energy Corporation installed the nation's first 1000-feat longwall face in April and May of 1984. The face completed the first panel in October, 1984, and recovery was begun. Roof Strata consolidation for the recovery was accomplished by a RokLok polyurethane binder infection program designed and supervised by Halbach & Braun Industries. The application provided the most rigorous and demanding test to date of this method's performance and cost-effectiveness relative to bolts and wire screen.

Jan 1, 1984

By Bruce Hebblewhite

An ACARP-funded industry research project in Australia recently investigated the problem of premature rock bolt failures in underground coal mines. The project carried out limited sampling from 9 different collieries in NSW and Queensland, followed by a more comprehensive, controlled sampling from one colliery. Over 50 broken bolts were collected and subjected to metallurgical analysis at UNSW to determine both the steel composition and to analyse the fracture surfaces. Prior to this study, there had been anecdotal evidence of similar bolt failures from a number of sites within the industry. The sampling and analysis conducted by this project - whilst being below a statistically representative sample of the entire industry bolt population - highlighted the fact that bolt failures were continuing to occur at a number of sites, in both older and recently installed bolts. The failures were almost entirely attributable to stress corrosion cracking (SCC). It appears that a combination of factors - including steel composition, bolt manufacturing process, loading environment, geological and hydrological environment, bacterial corrosion - can all contribute to this problem. There is no simple solution, however, as with similar research findings from the UK, it appears that steels with higher values of fracture toughness, or Charpy Index, are less susceptible to SCC. Testing to date has been limited to bolt failures below the resin encapsulation horizon. A real concern is the potential extent of the problem at higher horizons, within the encapsulation. These may require some form of non-destructive testing (NDT) for detection. Initial trials in Australia of the ultrasonic device developed by DMT in Germany have proved encouraging. Further testing using this device is anticipated in future research. This paper describes the outcomes of the project, completed in 2002.

Jan 1, 2003

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By Kot Unrug

Fully grouted tensioned bolts provide a desirable compressive of laminated roof and bondage along the entire bolt length, at the same time the entire surface of the hole is protected against penetration of moisture. This is particularly important in shale strata, where, when left unprotected by a partial grout column, moisture penetrates to the annular space, and weathers rock around the bolt hole, having an easy access to the bedding planes which are strongly hydrophilic. The most desirable are thrust tensioned rebar bolts that can be installed with one procedure step, and can secure a desired pre-stressing. Such bolts have a forged conventional head and offer no hazard to miners in low clearance mines, whose number increase constantly due to the depletion of reserves in thicker seams. The presented field-testing program has been based on instrumented bolts allowing for monitoring of tension at installation and at a chosen time interval after. The tested system is based on rebar bolts installed with two speed Fosroc resin (fast at the top and stow at the bottom), and mechanical compression by the bolting machine at installation. Combination of several different washer -- plate arrangements have been tested. The results are reported with their interpretation, and recommendations directly towards strata control requirements, as well as the operational considerations for efficiency of installation.

Jan 1, 2002

By David F. Gearhart, Khaled M. Mohamed

"Trusses are primarily used as passive roof supports in coal mines. They are constructed of three main parts: two grouted bolts installed at opposing forty-five degree angles into the roof so that they are anchored over the ribs and a cross member that ties the angled bolts together. There is also hardware used to assemble these components. The capacities of the angled bolts are typically 30 to 40 tons and the tensile capacity of the cross member is also 30 to 40 tons. Importantly, the direction of the immediate roof loading on the cross member is unlike the direction of the loading on the angled bolts. The load on the cross member is transverse to the longitudinal axis instead of along it, and therefore the cross member is loaded in the weakest direction.Previous tests conducted on truss systems applied loads such that the increasing tension in the two diagonal bolts increased the tension in the horizontal cross member, resulting in a stiff response. By contrast, if the load is applied directly to the cross member, which then transmits those forces to the diagonal bolts, it results in a much softer response.Based on this difference, laboratory tests to apply transverse loads and measure the vertical load capacity of three different types of cross members were conducted using the Mine Roof Simulator (MRS) located at the National Institute for Occupational Safety and Health (NIOSH) in Pittsburgh. The length of the samples was about 16 feet. Single-point load tests, with the load applied in the center of the specimen were conducted to verify the performance of the test arrangement and the finite element models. Double-point load tests, with a span of eight feet, were also conducted. This arrangement replicates the performance of the cross members with a distributed load. Both of these test arrangements were conducted on one-inch-diameter threaded steel bars and 0.7-inch-diameter cable and 0.6-inch-diameter cable cross members.For the single-point load configuration, the yield of the one-inch bar was nominally 22 kips of vertical load, achieved at 17 inches of deflection. For both sizes of the cable cross members, yield was not achieved even after 18 inches of deflection. Peak vertical loads were about 20 kips for the 0.7-inch cables and 15 kips for the 0.6- inch cables. For the double-point load configurations, the one-inch bar cross members yielded at 33 kips of vertical load and 10 inches of deflection. The 0.7-inch-diameter cable cross members broke strands at 30 kips of vertical load and 10 inches of closure, and the 0.6-inch-diameter cable cross members broke strands at 25 kips of vertical load and 10 inches of closure. Finite element models of each of the six different configurations were developed and show the variation of the vertical capacity of the cross members and the difference of the behavior of the bar versus the cables."

Jan 1, 2015