Search Documents

By Li Yang, Andre Cezar Zingano, Alberto Fronza

"Immediate roof control is very important to the security and stability of entries in coal mining. It is also the highest cost in the coal mining operation, and roof spalling is directly responsible for coal contamination. The immediate roof in the coal mines in the State of Santa Catarina varies in lithology and in the presence of structures, such as bedding planes, vertical fractures that cut lamination, sandstone, and siltstone boulders. The presence and crossing of these structures should influence the decision of the specification of the roof support. Furthermore, the variation of rock layer and quality of the roof must be immediately followed by the variation of support specification. This work aims to study the behavior of the immediate roof under different geological and structural conditions during the excavation of entries, including the changing of the geometry of the entry as a function of time. This includes the effect of vertical fractures that cross the bedding planes of the roof and the position of those fractures on the roof. The effect of time between excavation and installing support to stabilize the roof is also examined. This study uses empirical methodologies for support design and numerical methods to study the behavior of the roof when anchored to the different scenarios proposed. The results of this work show the importance of quality characterization of the roof in terms of the type of rock and its thickness and the presence of vertical fractures that cut the bedding planes of the roof immediately.INTRODUCTION The immediate roof in a coal mine can varies in terms of typology and structural features, like bedding plane spacing and vertical joints. The roof support must be specified based on the features of the roof layer and its classification. Unal (1983) and Mark, Molinda, and Dolinar (2001) suggest that the roof support design should be based on the rock mass rating (RMR) and coal mining roof rating (CMRR), which look at rock mass classifications. These methods are based on the beam-building approach, and the bedding planes are tied together using fully grouted bolt. The bolt can be pre-tensioned or not depending the time of the curing of the resin."

Jan 1, 2017

By Yun Zhang, Haijun Jiang, Shenggen Cao, Chen Wang

The distribution of front abutment pressure is closely related to the force, deformation and energy distribution of hard roof before periodic weighting. So it is necessary to carry out research on the relationship between them. According to front abutment pressure distribution feature, using the location of peak front abutment pressure as the dividing point, coal seam is divided into two parts along the direction of mining: the yield zone that is the area between the faceline and the point where the maximum front abutment pressure occurs, and the elastic zone that is the part before the point of peak front abutment pressure. The proposed mechanical model of unit width hard roof at the panel center periodic weighting consists of five parts including the yield zone. All parameters of the deflection equations for each of the five parts that satisfy the continuity conditions and natural boundary conditions are obtained by using the Matlab software. The continuous curves of front abutment pressure, deflection, bending moment and bending strain energy density distribution of hard roof are obtained by iterative approximation method. The following conclusions can be drawn through analyzing those curves: (1) The position of peak front abutment pressure is located at the transition of coal seam foundation from yield zone to elastic zone (elastoyield critical point), the distance of it to the faceline is equal to the width of yield zone. The peak front abutment pressure increases with yield zone with. (2) The peak bending moment in front of the faceline, and the distance of it to the faceline increase with the yield zone width. The deflection of hard roof at the face and midspan also increase with yield zone width. (3) As the yield zone width increases, the accumulated elastic energy of hard roof in front of the faceline increases, and the core zone of energy moves forward away from the face. (4) When the yield zone width is zero, the whole coal foundation is regarded as elastic foundation, and the peak front abutment pressure occurs at the faceline.

Jan 1, 2015

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By Gerald I. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of the rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock ]avers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified, In order to determine the application of the drilling parameters for identifying rout rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble. and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation or, the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

Jan 1, 2000

By Peng-Fei He

CT scanning tests were used to detect the pre-existing fracture systems of 36 cubical coal blocks. Systematic procedures were developed to construct the pre-existing fracture geometry of the cubical coal blocks from the CT images. Based on the constructed fracture systems, the fracture tensor components were calculated to capture the directional effects of the fracture system of the cubical coal blocks. The effect of the pre-existing fracture system and different combinations of confining stresses on the strength and deformability of coal masses was investigated at a preliminary level using some true triaxial test results and the computed fracture tensor components. The strength of the cubical coal blocks in the loading direction was found to be closely related to the summation of the fracture tensor components in the two perpendicular directions to the loading direction and the level of the confining stress system. The deformability of cubic coal blocks in the loading direction was found to be correlated to the fracture tensor component in the same direction.

Jan 1, 2014

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By André Zingano

This paper analyses possible causes for floor heaving in room-and-pillar coal mining. The coal mines are in the southern part of Brazil, where the Barro Branco Coal Seam varies in depth from 20m to 400m, and a very thick volcanic formation overlies part of the sedimentary basin. The erosion of part of the volcanic formation causes this large range of overburden thickness, which formed large V-type valleys. The mine in study is located near the slope of one of these valleys. The mine inclined shaft is at the lower overburden thickness area of the valley and the mining is developing toward the thicker overburden area. The floor heave occurred in the crosscuts, which are parallel to the slope valley direction. Numerical modeling was applied to study the stress distribution around the openings; and fieldwork on the floor heaved entries was carried out. The geometry of mining (pillar and openings width) also was analyzed. The results showed that the very weak rock and the high horizontal stress were the causes of floor heave. As the mining gets near the valley slope, the stress distribution around the crosscuts changes considerably. In addition, the stress distribution changes as the mining goes far from the crosscut. Keywords: floor failure, room and pillar, finite element model

Jan 1, 2002

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U.S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of a recorded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with hump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip. etc.) of the failure of the strata surrounding the active and multi¬panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

Jan 1, 2000

By David F. Gearhart, Khaled M. Mohamed

"Trusses are primarily used as passive roof supports in coal mines. They are constructed of three main parts: two grouted bolts installed at opposing forty-five degree angles into the roof so that they are anchored over the ribs and a cross member that ties the angled bolts together. There is also hardware used to assemble these components. The capacities of the angled bolts are typically 30 to 40 tons and the tensile capacity of the cross member is also 30 to 40 tons. Importantly, the direction of the immediate roof loading on the cross member is unlike the direction of the loading on the angled bolts. The load on the cross member is transverse to the longitudinal axis instead of along it, and therefore the cross member is loaded in the weakest direction.Previous tests conducted on truss systems applied loads such that the increasing tension in the two diagonal bolts increased the tension in the horizontal cross member, resulting in a stiff response. By contrast, if the load is applied directly to the cross member, which then transmits those forces to the diagonal bolts, it results in a much softer response.Based on this difference, laboratory tests to apply transverse loads and measure the vertical load capacity of three different types of cross members were conducted using the Mine Roof Simulator (MRS) located at the National Institute for Occupational Safety and Health (NIOSH) in Pittsburgh. The length of the samples was about 16 feet. Single-point load tests, with the load applied in the center of the specimen were conducted to verify the performance of the test arrangement and the finite element models. Double-point load tests, with a span of eight feet, were also conducted. This arrangement replicates the performance of the cross members with a distributed load. Both of these test arrangements were conducted on one-inch-diameter threaded steel bars and 0.7-inch-diameter cable and 0.6-inch-diameter cable cross members.For the single-point load configuration, the yield of the one-inch bar was nominally 22 kips of vertical load, achieved at 17 inches of deflection. For both sizes of the cable cross members, yield was not achieved even after 18 inches of deflection. Peak vertical loads were about 20 kips for the 0.7-inch cables and 15 kips for the 0.6- inch cables. For the double-point load configurations, the one-inch bar cross members yielded at 33 kips of vertical load and 10 inches of deflection. The 0.7-inch-diameter cable cross members broke strands at 30 kips of vertical load and 10 inches of closure, and the 0.6-inch-diameter cable cross members broke strands at 25 kips of vertical load and 10 inches of closure. Finite element models of each of the six different configurations were developed and show the variation of the vertical capacity of the cross members and the difference of the behavior of the bar versus the cables."

Jan 1, 2015

By Michael J. Peacock

The Powhatan No. 4 Mine is located in southeastern Ohio along the Ohio River in Monroe County. The mine produces approximately 3.2 million tons of steam coal annually from the Pittsburgh No. 8 seam. The Pittsburgh No. 8 seam in this area dips to the southeast in varying amounts from 10-feet to 40-feet per mile. The seam is made up of a main bench coal (4' to 5f' ) containing several thin and variable partings and a rider ("roof") coal (0" to 18") which is separated from the main bench by a parting (0" to 18") that is reasonably consistent in occurrence and position. Strata overlying the seam varies from a bedded to nonbedded calcareous mudstone-claystone (6' to 12') in the north and east regions of the mine to a sandstone (Pittsburgh Sandstone C10' to 40'1 in the south and west regions. The Redstone Limestone (10' to 18' ) overlying the mudstone-claystone in the north and east thins and rises toward the area of sandstone deposition in the south and west. From its opening in April of 1971 until late 1981, primary roof support in the long-1 ived entries at Quarto Mining Company's Powhatan No. 4 Mine had been achieved with 8-foot and 10-foot. 518-inch mechanical roof bolts using a Single expansion shell. These bolts were installed so that the expansion shell achieved a competent anchorage in the limestone. However, as the mine developed westward, the limestone began to trend upward becoming inaccessible as an anchorage medium at the 8-foot and 10-foot horizons. Anchorage achieved in the underlying mudstone-claystone strata was failure-prone due to weathering (after exposure to air and moisture) and inconsistencies in the anchorage horizon, leading to an increase in the incidence of reportable roof falls at the mine. Responding to the threat to safety and productivity posed by the increase in roof falls. Mine Management through its Safety and Engineering Departments, sought solutions to the problem. In seeking a solution to the problem, the safest and en engineering groups examined the reportable roof falls to determine the cause of those failures. Their examination pinpointed two items which were found to be a common link in the majority of those falls; namely, anchor integrity and geologic trends. Analysis of the roof falls indicated that due to effects of air and moisture on the anchoraae zones in the mudstones and clay- itones, the integrity of the anchorage over time could not be maintained. Geologic trends noted included the upward trend of the -main limestone as mining progressed westward, inconsistencies in the amount of roof coal and draw slate in the immediate mine roof and increasing evidence of heavily slickensided immediate mine roof. In the absence of the protective barrier provided by the roof coal, the immediate strata and particularly the draw slate, is susceptible to deterioration due to the weathering effects of air and moisture and thus is prone to "eat out" around the roof bolts and cause roof falls. The presence of heavily slickensided roof creates a need for increased contact surface such as that provided by plank and header blocks to aid in holding up the roof and tends to make the behavior of such roof very unpredictable. Having determined the causes of the roof falls. Mine Management began to identify the kind of roof support which would best solve these problems, while at the same time providing the mine with a safe, cost effective and efficient roof support system. This paper will provide an analysis of how this decision was reached, the background that was researched to aid in forming the decision, the considerations that played key roles in the formulation of the plan, the mechanics of following through and implementing the new roof support system, and an assessment of the resultant gains in safety, productivity and improved costs derived from the implementation of the new roof support system.

Jan 1, 1986

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Ulrich Langosch

In the 1990s the German mining industry introduced a new generation of shield supports. The new design of support has a maximum load capacity of 10,000 kN, making these units as strong as the shields used in Australia and in the USA. DMT took more than 3,100 underground observations in order to verify the roof fall frequency by statistical analysis. The results of this work have led to practical recommendations for roof control and the required shield support system on longwall faces. The underground observations have been correlated to Rock Mass Classification, to stress calculations and to the angle between the direction of the fissures and the direction of longwall mining_ The analysis work yielded the following two sets of results: 1. There is a critical distance between the canopy tip and the coal face (Tip to Face TF,n,). The TF,n, is predictable and relates to: the thickness of the first roof layer and its uniaxial compressive strength. The face support should have a TF that is less than the TFcrtt in every underground longwall situation. Exceeding the TF crit call immediately result in a roof fall. 2. Using the obtained regression equation DMT is able to calculate the probability of the roof fall frequency (FF), which describes the roof fall sensitivity. When TFcr;, is exceeded the predicted roof fall FF relates to: the measured support resistance (MSR) of the shield support the calculated vertical stress (p?) the fissure-direction index (DI = angle between main fissure direction and direction of mining) and the distance by which TFcrit is exceeded (ATF). Armed with these results DMT is now able to predict the critical distance between the tip of the canopy and the coal face (TFcrit), as well as the roof fall frequency, for all shield designs. By applying the new calculation method it is now possible to compare alternative longwall layouts and different shield support types under pre-set geological conditions. Mining engineers on site are therefore in a position to make the necessary roof control preparations required to run the longwall operation to maximum efficiency. The results provide a useful basis for making practical recommendations and for selecting the most effective design of shield support. The paper uses practical examples to demonstrate the R&D results and present the various methods now available for calculation and prediction in longwall roof control.

Jan 1, 2003

By Kudret Tutuk, Serkan Saydam, Sungsoon Mo

"This paper presents an overview of the floor heave management at the Glencore Bulga Underground Operations and investigates the contributing factors to the behaviour of the floor. The mine experienced a number of major floor heave events in gateroads on development. As the longwall face approached the roadways, the magnitude of floor heave frequently increased, while new floor heave also developed. Furthermore, severe floor heave events took place along the longwall face. The most observed failure mode was buckling. While regular floor measurements were conducted to better understand the nature of the phenomenon, and various measures were considered to control the deformation of floor, the mining height was increased for the predicted floor heave domains, which facilitated effective management of the floor issues. The experience in the mine indicates that mainly high horizontal stresses with greater depths of cover and certain types of floor lithology configuration are likely to contribute to the failures of floor strata.INTRODUCTIONThe Glencore Bulga Underground is located in the Southwest of Singleton in the Hunter Valley of New South Wales, Australia. Blakefield South, part of Bulga Underground, commenced longwall mining in 2010, extracting coal from the Blakefield seam, while the overlying longwall panels were previously mined from the Whybrow seam. The coal seam ranges from 4.5 m to 8.0 m thick with the mining heights varying from 2.9 m to 3.5 m. The longwall panels are 320 m and 400 m wide and up to 3.5 km long.The mine experienced a wide range of floor issues around longwall panels LW7 and LW8, both 400 m wide. For instance, the concrete floor in the travel road failed and lifted as the longwall retreated in close proximity as can be seen in Figure 1. Figure 2 shows the beam stage loader (BSL) buried into the lifted floor, and Figure 3 shows a timber prop distorted due to the movement of the floor. In addition, severe deformation of the floor along the longwall face impeded the longwall operation, as shown in Figure 4."

Jan 1, 2018

By Baogui Yang, Jie Yang, Anthony Iannacchione

"The cemented coal gangue-fly ash backfill technique (CGFB) has commonly been used to control subsidence damage caused by underground coal mining. This paper discusses the CGFB backfilling process used at the Xin-Yang coal mine, Shanxi Province, China. A general description of the components of the CGFB are provided. The reaction of the strata to the backfilling process is simulated with a scaled physical model based on the Xin-Yang conditions and verified with subsidence points on the surface. With the help of the cemented filling materials, the CGFB produces only a slight bend to the overburden roof strata over the longwall panel. Physical models were constructed at the China University of Mining and Technology, Beijing, to simulate actual conditions. The modeling results show minor fracture distribution in the overlying strata and lower abutment pressure development within the backfilling area. The effectiveness of the CGFB technique is verified by a reduction in the vertical surface subsidence measured above the backfilled area.INTRODUCTIONUnderground longwall mining is the most efficient underground means to recover coal resources and is used widely in China, the US, Australia, and Europe. However, this type of mining has introduced some serious environmental impacts. Perhaps the most significant environmental issues are the surface and groundwater impacts associated with the formation of the subsidence basin (Bell and Donnelly, 2006). Backfill technology has been used for years to mitigate subsidence impact. Simply speaking, the backfilling technique places filling materials into the void left from the extraction of coal. When this material is placed within the gob, it is capable of partially supporting the overburden until a new equilibrium is reached. Essentially, the backfill material inhibits crack development and expansion caused by the strata movement and mitigates damaging ground deformations.The cemented gangue-fly ash backfill (CGFB) is one type of novel backfill technology, consisting of cement, coal gangue, fly ash, water, and additives in varying concentrations. The CGFB is mixed on the surface, pumped underground through a pipeline as a slurry, and placed in the void behind the longwall shield under the protection of specially designed hydraulic supports."

Jan 1, 2018

By Xinzhi (Thomas) Du

"In order to monitor the overburden strata deformation over a longwall mining area in the Pittsburgh Coal Seam, three boreholes were drilled across the longwall panel. Each borehole employed multiple-point borehole extensometers (MBE) to monitor overburden strata movement during and after the longwall face passed under the study area. The longwall face in the study area was 1,428 ft wide and 4,000 ft long. The average mining height was about 7 ft. The overburden depth ranged from 550 ft to 650 ft with an average of 600 ft. The final extensometer readings indicated that overburden strata initially showed sign of movement when the longwall face was 700 ft inby the MBE. The rate of strata movement accelerated when the face was 300 ft inby MBE. When the face was directly under MBE, a sudden anchor displacement occurred, indicating rapid strata movement once under-mined gob. The readings showed insignificant strata movement after the longwall face was 400–700 ft outby MBE.INTRODUCTIONThe longwall mining method is an efficient mining method of underground mining. Surface and subsurface strata are inevitably disturbed above the longwall mined out gob. Figure 1 shows the four zones of disturbance in the overburden strata in response to longwall mining.A longwall shear cuts the coal seam and allows the immediate roof strata to cave into irregular blocky material to fill the void. This is called the caved zone. The caved zone extends from the mining horizon to six or eight times the mining height, depending on the bulk factor of each caving strata layer. The fractured zone is located above the caved zone, in which the strata breaks into regular blocks by vertical or sub-vertical fractures caused by bending forces due to the weight of the underlying strata. The surface soil and rock crack zone extends to approximately 50 ft below the surface. The surface cracking is caused by downward movement of the surface. Between the fractured zone and surface crack zone is the continuous deformation zone. The strata in this zone deforms gently without causing any major cracks that extend long enough to cut through the thickness of the strata, as in the fractured zone (Peng, 2006).The objective of this project is to provide fundamental rock mechanics research about overburden strata movement response to longwall-related activity. The findings aid in better understanding pillar stability, gas well subsidence management, hydraulic impacts, and numerical modeling."

Jan 1, 2018

By Ihsan Berk Tulu

The complex interaction between multiple seam pillar extraction panels and variable topography can generate unexpected ground control problems. This case study describes stress-related damage in multiple seam workings that resulted in difficult operating conditions and compromised the safety of the support crews. The damage appeared to be caused by horizontal stress but the unexpected location of the damage baffled the authors. A 2D Finite element analysis was conducted of the mine layout and surface topography in an attempt to explain the observed failure. It was discovered that the topography resulted in the rotation of the major stress at the location of the current workings. The stress rotation caused asymmetrical interactions between the workings on the different coal beds, which can explain the unexpected response observed in the mine. Consequently the layout of the next panel was changed by locating the vulnerable entry 30 ft away from its originally planned position. The new location was selected to locate the entry in favorable stress conditions. The change in layout resulted in a significant improvement in conditions when the next panel was mined. At the time of writing this paper, a full panel has been developed using the modified layout without undue ground control problems. The case study demonstrates that numerical models can help engineers to interpret and solve complex multi-seam interaction problems.

Jan 1, 2014

By Peng Cao, Jimin Su, Yang Li

"Abutment pressure distribution is different when a longwall panel is passing through the abandoned gateroads in a damaged coal seam. According to the geological conditon of panel E13103 in Cuijiazhai Coal Mine in China theoretical analysis and finite element numerical simulation were used to determine the front pressure distribution characteristics when the longwall face is 70 m, 50 m, 30 m, 20 m, 10 m, and 5 m from the abandoned gateroads. The research results show that the influence range of abutment pressure is 40 m to 45 m outby the face, and the peak value of front abutment pressure is related to the distance between the face and abandoned gateroads. When the distance between the longwall face and abandoned gateroads is reduced from 50 m to 10 m, the front abutment pressure peak value kept increasing.When the distance is 10 m, it has reached the maximum. The peak value is located in 5 to 6 m outby the faceline. When the distance between the longwall face and abandoned gateroads is reduced from10 m to 5 m, the front abutment pressure sharply decreases, the intact coal yields and is even in plastic state. The peak value transfers to the other side of the abandoned gateroads. The research results provide a theoretical basis for determining the advance support distance of two gateroads in the panel and the reinforcement for face stability when the longwall face is passing through the abandoned gateroads.INTRODUCTIONFront abutment pressure is the result of rearrangement of in situ rock stress caused by the mining (removal) of the coal seam. Research on the distribution character of face abutment pressure have significant importance in confirming the width of the coal pillar and the distance of advance support in roadways (Liu et al., 2011; Liu, Jiang, and Zhu, 2015). Currently, there is a lot of research on abutment pressure characteristics of traditional longwall coal faces, thick coal seam longwall faces, isolated faces, and extra wide face abutment pressure distribution (Xie et al., 2006). However, theoretical analysis and research on the distribution law of the fully mechanized coal face to abandoned gateroads are relatively less. Abandoned roadways are often from less mechanized or room and pillar mines. Due to the existence of these roadways pre-longwall mining, the in situ stress has already been redistributed around the roadway (Liu et al., 2007). Thus, when the longwall approaches and mines through the roadway, the abutment pressure distribution behaviour has different characteristics than those of traditional solid undisturbed coal. Especially when the face approaches the abandoned roadway, the understanding of face abutment pressure distribution has significant importance to the timing of support installation (Ren and Ning, 2014). This prevents the occurrence of a roof and rib failure ahead of and on the longwall and highly efficient advance of the longwall safely and productivity. This paper analyses the E13103 face of the Cuijiazhai Mine of Wenzhou Mining Co., Ltd of Kailuan Group, as the engineering case study, and uses FLAC3D numerical simulation software to conduct numerical simulated analysis on the abutment pressure distribution mechanism of longwall coal mining face."

Jan 1, 2018