Search Documents

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By Peter Zhang

Room and pillar mining under shallow depth is usually conducted with a high extraction ratio, which leaves small pillars with a low safety factor in some old workings in abandoned mines. Pillar sloughage, squeezing or even collapse may have occurred in those old workings with small pillars, either at the time of mining or later. The conditions of the pillars in abandoned mines can affect mining above them. Subsidence fractures and abutment pressure are indications of multi-seam interaction caused by squeezing or collapse of small pillars. To mine over areas with potentially unstable small pillars, the panel layout in the upper seam should be such that multi-seam interaction can be minimized and proper roof and rib support should be installed in the influence zones. This case study presents an example of multi-seam mining above small pillars under a shallow depth of cover. Though the interburden is relatively thick and competent, interaction is still present over the influence zones. Pillar stability and multi-seam interaction analysis, numerical modeling and in-situ monitoring are presented to demonstrate how the upper seam can be mined safely over the small pillars.

Jan 1, 2014

By Navid Hosseini

Several empirical equations to estimate coal pillar strength have been presented in academic studies. The development processes of these equations are similar and are usually obtained by fitting the mathematical function (curve) to field data. One of the best criteria to evaluate the quality of fitting for such equations is the correlation coefficient R2, which has limited applicability. It is necessary to calculate the correlation coefficient access to the initial data for which the equation is presented; this is impossible for many coal pillar strength formulas. This paper presents a new approach based on the analysis of uncertainty amplitude to compare the coal pillar strength. This approach utilizes a combination of parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), function type and degrees of freedom. The confidence level of constants is subsequently formed and the correlation coefficient becomes more comprehensive. Therefore, for an effective comparison, the efficiency and accuracy of coal pillar strength formula can be used. Keywords: Coal Pillar Strength, Correlation Coefficient, MATLAB, Uncertainty Criterion

Jan 1, 2012

By David A. Newman

Barrier pillars created during mine development provide additional reserves during mine closure and can be the sole access to reserves previously abandoned because of mining height or out of seam dilution limitations. The safe and successful mining of barrier pillars requires a thorough knowledge of the magnitude and distribution of the vertical stress field in addition to the strength and physical properties of the coal, immediate roof, and immediate floor strata. Quantifying the vertical stress field is complicated by the combination of the overburden stress, abutment stresses transferred onto the barrier pillar from adjacent gob areas, and in multiple seam mining, stresses transferred from abandoned subjacent mines. These variables make the extraction and development of barrier pillar reserves a site specific consideration. Three case histories are presented in which barrier pillar development and extraction provides; i) an access point and the means to ventilate a large area of low seam reserves left by a prior operator after developing only the thicker areas of a multiple split reserve, ii) the means to increase total recovery of a deep, thick seam longwall reserve, and iii) opportunities for the development and retreat mining of a two mile long barrier pillar in thick seam reserves.

Jan 1, 1995

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By Stephen C. Tadolini

Effective barrier pillar design is an essential component for safe and productive underground coal mining. Barrier pillar design methodologies that incorporate sound engineering judgment have been used for practical everyday usage. The next logical step is to utilize numerical modeling techniques that help combine practical experience and empirical observations into barrier pillar design analysis. A case study is presented that describes the barrier pillar design process, but also highlights the importance of considering the global mine response by evaluating: adjacent pillar stabilities, impact of intersection and entry widths, capacity of primary and secondary bolting systems and rib stabilization used for the safe and efficient removal of the longwall face equipment.

Jan 1, 2013

By D. W. H. Su

Following a roof fall in the B12 headgate of a CONSOL Pennsylvania Coal Company (CCPC) underground coal mine in February 1998, CONSOL R&D and Exploration initiated an underground roof geology reconnaissance program along the B13 and B14 developments to define potential roof instability areas and to recommend appropriate supplemental headgate support. This reconnaissance program revealed the presence of a thick, massive Pittsburgh sandstone channel overlying the B13 and B14 panels. Surface and underground core holes confirmed the close proximity and the very massive, nonlaminated nature of the sandstone. To mitigate anticipated adverse conditions at the B 13 and B 14 longwall faces due to delayed caving of the massive sandstone behind the shields, a task force consisting of Operations, Exploration, and R&D personnel was formed in May 1998. Several operational adjustments were made by mine management, including repairing damaged lemniscate links, maintaining immediate forward shield support, and implementing measures recommended by the task force intended to boost the shield set load density at the face. After reviewing available geotcchnical information, the task force also recommended fracing of the massive sandstone over the B13 and B14 panels to enhance caving characteristics and further reduce the bending-induced stresses in the sandstone near the face. Horizontal fracs were created at a horizon about 25 feet above the Pittsburgh seam main bench over the two panels in June and November 1998, respectively. To evaluate the effect of sandstone fracing and operational adjustments on the bending-induced stresses in the sandstone, three finite element models were constructed and analyzed. Results from the finite element analyses indicate that one horizontal frac, 25 feet above the Pittsburgh seam, would reduce the bending-induced stresses in the sandstone by approximately 50 percent, maintaining them at a level below the ultimate strength of the sandstone. Operational adjustments to increase the support set load density and support stiffness could reduce the bending-induced stresses in the sandstone by a maximum of an additional 10 percent. Shield pressure monitoring at the B14 midface confirmed the presence of a lower roof pressure zone inby and outby the 1314 frac holes. This lower face pressure significantly contributed to improving the B13 and B14 longwall productivity and safety. The total production downtime due to bad top at the B 12 face within the interval of channel influence was 30,600 minutes compared to about 3,500 minutes each for the B13 and B14 faces. The average longwall advance per machine shift for the B13 and B14 faces within the channel was about 70 percent higher than that for the B 12 face.

Jan 1, 2001

By David Miller

Longwall gateroad support can be supplied by a variety of methods. The system of support also needs to be flexible as conditions change. This is especially true in the complex geological conditions of the west Kentucky # 13 seam. Methods of gateroad support used in this seam will be presented along with the successes and failures of the systems as conditions changed Lodestar Energy's gateroad support progression through the seven longwall panels retreated to date will provide an insight into planning for future panels

Jan 1, 1998

By Nikolaos Polysos

For the planning and driving of gateroads supported by roof bolts a practical concept has been developed in order to determine the geological and rock mechanical parameters derived from exploration drillholes. Based on this, an assessment scheme for the design of roof bolting has been established. The new methods of investigation comprise of geotechnical logging of drill cores for the determination of structural-geological rock characteristics and complementary geophysical well-logging which enables the evaluation of petro-physical and rock mechanical properties. The tools and their measurements will be briefly presented. The relationship between the geophysical log readings and the geotechnical parameters will be illustrated. The aim of the data acquisition is to improve roof bolting design which is based on the assessment scheme. This will be adjusted to the prevailing rock mechanical conditions and stands up to the required stability of the gate roads. In order to ensure consistent data acquisition, a method of core logging has been standardized for the respective demands. To achieve this it was necessary to introduce specific parameters and new methods. For the recording of linear and planar structural elements at the drill core, a special system for the documentation of the angles in relation to each other has been set up. The rock mechanical parameters and their acquisition will be explained. In order to carry out an objective analysis as fast as possible, software has been developed for the acquisition, management and presentation of the data. These programs and their functions will also be presented. The software is characterized by being user-friendly and the flexibility of its interfaces, Different options for the combined presentation of input and evaluated data give a more objective basis for the planning of roof bolt design. Examples will illustrate the operational implementation of the results during the planning and driving phases.

Jan 1, 2001

By Simon H. Prassetyo

Violent failures of coal pillars, known in practice as coal mine bumps, have long been a subject of investigation. Many field investigations have considered geological conditions that create high stress in the pillar to be the main causative factor leading to bumps. In recent years, constraint at interfaces has been observed to be associated with the occurrence of coal bursts. This paper shows how interface friction and width-to-height (W/H) ratio affect the degree of violence of coal specimen failure. A series of UCS tests on 178 coal samples from bump-prone (Utah, called UT coal) and non-bump-prone (West Virginia, called WV coal) mines were conducted. Three violent failure parameters? peak sound pressure level, core zone failure, and ultimate stress? were used to assess the violence of failure. The degree of violence were investigated at varying interface frictions (high: µ = 0.40, medium: µ = 0.22, and low: µ = 0.13) and W/H ratios (W/H = 2, 3, 4, 5, 6, 7, 8, 10, and 12). A simulation series of modeled coal specimen under uniaxial loading was also conducted using the finite element method to observe the equivalent plastic strain distribution experienced by the modeled coal specimens. It was found that the violence of coal specimen failure depends on W/H ratio and interface friction. Interface friction has more significant influence on the violence of failure at high W/H ratios than it does at low W/H ratios.

Jan 1, 2011

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

By Dwayne C. Kicker

This paper introduces the concept of design theory and methodology as applied to rock mechanics for more innovative and efficient design. This is a "frontier" research area in rock mechanics because although design is a fundamental foundation to all engineering branches, very little attention has been paid to this aspect in mining. In discussing the theoretical premise of design, this paper identifies the principles which form the basis of design activity. Also, from a practical viewpoint, the findings from a series of interviews with mine design engineers are presented. These findings lead to the identification of needs arising from overlooked design methodology in practice.

Jan 1, 1989

By Li Yang, Andre Cezar Zingano, Alberto Fronza

"Immediate roof control is very important to the security and stability of entries in coal mining. It is also the highest cost in the coal mining operation, and roof spalling is directly responsible for coal contamination. The immediate roof in the coal mines in the State of Santa Catarina varies in lithology and in the presence of structures, such as bedding planes, vertical fractures that cut lamination, sandstone, and siltstone boulders. The presence and crossing of these structures should influence the decision of the specification of the roof support. Furthermore, the variation of rock layer and quality of the roof must be immediately followed by the variation of support specification. This work aims to study the behavior of the immediate roof under different geological and structural conditions during the excavation of entries, including the changing of the geometry of the entry as a function of time. This includes the effect of vertical fractures that cross the bedding planes of the roof and the position of those fractures on the roof. The effect of time between excavation and installing support to stabilize the roof is also examined. This study uses empirical methodologies for support design and numerical methods to study the behavior of the roof when anchored to the different scenarios proposed. The results of this work show the importance of quality characterization of the roof in terms of the type of rock and its thickness and the presence of vertical fractures that cut the bedding planes of the roof immediately.INTRODUCTION The immediate roof in a coal mine can varies in terms of typology and structural features, like bedding plane spacing and vertical joints. The roof support must be specified based on the features of the roof layer and its classification. Unal (1983) and Mark, Molinda, and Dolinar (2001) suggest that the roof support design should be based on the rock mass rating (RMR) and coal mining roof rating (CMRR), which look at rock mass classifications. These methods are based on the beam-building approach, and the bedding planes are tied together using fully grouted bolt. The bolt can be pre-tensioned or not depending the time of the curing of the resin."

Jan 1, 2017

By John C. Stankus

Jennmar Corporation. in an effort to improve mine roof control, has conducted extensive study and research comparing tensioned point anchor resin systems versus the use of non-tensioned fully grouted rehar. Preliminary indications are showing that in thinly laminated, weak strata, tensioned point anchor resin systems are providing more effective roof control than the non-tensioned fully grouted rehar. In this paper two case studies are presented in which tensioned point anchor resin systems were utilized to stabilize and control the mine roof in two different mines. Both mines are alike in many ways, but yet very different in other aspects. However, the mines do share one main common factor. and that being the non-effectiveness of the non-tensioned fully grouted rebar in controlling the thinly lamininated strata in each respective mine.

Jan 1, 1990

By Cosmo P. Fazio

Remote control roof bolting is approaching reality with the continued improvement of a number of components and subsystems being developed by The Bendix Corporation under sponsorship of the U.S. Bureau of Mines and the U.S. Department of Energy. The era of remote control research in roof bolting was initiated by the USBM in June of 1973 with the award of a contract to Bendix Corporation to design and build a roof bolt bender/inserter device. One year later in June of 1974, the Bureau awarded five parallel R&D contracts to develop a longer-than-seam-height flexible roof drill. The Bendix flexible drill design has been the most successful of the five, has been thoroughly tested in both laboratory and underground situations, and has been incorporated into a number of machine applications along with the roof bolt inserter. The purpose of this paper is to discuss the advantages of remote control bolting from both a safety and productivity standpoint. Applications of the flexible drill and roof bolt inserter on a number of government and industry supported programs are used to illustrate the advances being made toward the goal of remote control.

Jan 1, 1982

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Jinsheng Chen

The major functions of longwall headgate entries are to provide access ways to the outby submains or mains for coal transportation and to the longwall face for fresh air and for transporting men and material during longwall operations. Any roof control problems such as cutter roofs or roof falls in the outby headgate entries could result in significant production delays to the longwall face and may be a threat to miners' safety Under a thinly laminated immediate roof and a high horizontal stress field, even a longwall headgate entry that has an angle of less than 45 degree to the maximum horizontal stress may experience roof deterioration in the outby headgate if the longwall panel mining sequence and retreat direction are not properly considered. This paper attempts to analyze the causes of the roof control problems experienced in the longwall gate entries at our Cumberland and Emerald mines in Pennsylvania and to determine the optimal longwall panel mining sequence and retreat direction for the future mining area at Cumberland

Jan 1, 1998