Search Documents

By David Bigby

Rock Mechanics Technology has developed an intrinsically safe remote reading telltale system which allows up to 4 sets of 100 dual height, water diverting telltales in a mine roadway to be remotely monitored from a surface PC. The system has US MSHA approval and European ATEX approval for use in gassy mines. A successful full-scale application of the system employing 67 telltales was completed in a 1300m long maingate roadway during retreat of 183.0 longwall panel at West Mine in Germany between June 2001 and October 2002. During panel retreat a number of "teething" problems associated with the system were identified and resolved, the chief problem being associated with cable connection corrosion due to the unforeseen use of sprayed calcium chloride in the roadway. This paper describes the experience of employing the system at the colliery from the perspective of both the user and the manufacturer, and the improvements and developments which have resulted. The paper also presents examples of roof movement data recorded by the system, including data from behind the retreating longwall. The high resolution and data recording rate possible has resulted in particularly interesting information on roof behavior within the longwall front abutment area and behind the face. The paper also describes a series of new transducers and extensometers for the mining industry which employ the same physical principles and similar electronics to the remote reading telltale system. These have been applied in a variety of mining and tunneling environments worldwide over the last two years.

Jan 1, 2003

By Pierre-Yves Declercq, Andre Vervoort

"After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—an upward movement. Although most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method, surface movement still occurs many decades after mining is terminated. After the closure and flooding of underground excavations and surrounding rock, this movement is reversed. This paper focuses on quantifying the upward movement in two neighboring coal mines (Winterslag and Zwartberg, Belgium). The study is based on data from a remote sensing technique: interferometry with synthetic aperture radar (INSAR). The results of the study show that the rate of upward movement in the decade after closure is about 10 mm/year on average. The upward movements are not linked directly to the past exploitation directly underneath a location. The amounts of subsidence at specific locations are linked mainly to their positions relative to an inverse trough shape situated over the entire mined-out areas and their immediate surroundings. Local features, such as geological faults, can have a secondary effect on the local variation of the uplift. The processes of subsidence and uplift are based on completely different mechanisms. Subsidence is initiated by a caving process, while the process of uplift is clearly linked to flooding. INTRODUCTION After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—upward movement in the area above the past exploitation and in the immediate surroundings. Of course, most surface movement (i.e., subsidence) occurs in the months and years after mining by the longwall method (Peng, 1986). This downward movement continues to occur at a smaller rate many decades after mining has been terminated when the water in the underground excavations is pumped to the surface. This is the case as long as a mine is in operation. However, after the closure and flooding of the underground excavations and the surrounding rock, this movement is reversed, and the surface is uplifted. A total uplift of about half a meter has been recorded to date. This phenomenon has been described in several different coal basins in Europe, for example, in Belgium (Devleeschouwer et al., 2008), France (Samsonov, d’Oreye, and Smets, 2013), Germany (Baglikow, 2011), the Netherlands (Caro Cuenca, Hooper, and Hanssen, 2013), and Poland (Preusse, Kateloe, and Sroka, 2013). To date, research has focused mainly on understanding the phenomenon (e.g., Herrero et al., 2012) and identifying general trends, whereby the link with the rise in water levels is an important issue (Caro Cuenca, Hooper, and Hanssen, 2013). The most accepted explanation is linked to the swelling of clay minerals in the argillaceous rocks in the coal strata (Herrero et al., 2012). Without doubt, the full explanation is complex, and swelling is probably not the only cause of the residual movement. Most coal strata rock is weakened upon contact with water. The increase in water pressure also results in a decrease in the effective stress. Both aspects facilitate the fracturing of rock, which normally would result in further subsidence. However, decreases in the effective stresses also result in the relaxation or expansion of the rock, which induces an upward movement (Fjar et al., 2008). All of these aspects, including the long-term residual subsidence due to compaction under dry conditions, result in a net upward movement. The phenomenon discussed here is clearly different from the upsidence, sometimes observed on other continents (e.g., in Australia, Galvin, 2016). When upsidence occurs, the rock near the surface bends and buckles upwards due to the overstressing of the floors of the valleys."

Jan 1, 2017

By Heather E. Lawson

Recent field data providing measured pillar loading from a deep western mine revealed that an increased load transfer distance existed compared to expected values (Larson et al., 2012). Additionally, recent work by Tulu and Heasley (2012) has shown that the abutment angle in deep longwall mines can be significantly reduced as the depth of mining increases. The load transfer distance and abutment angle are both used as parameters to estimate pillar loading in longwall design. To investigate the potential implications of these observations on pillar loading in deep longwall mines, a parametric study using ALPS loading estimation procedures was performed. A supplemental study was conducted using LaModel to further investigate pillar loading at the tailgate. The study found that the abutment angle is particularly important for panels with supercritical geometries. As panels reach a subcritical geometry with increasing depth, the primary influence of the abutment angle is reduced and matched by other factors, including load transfer distance for tailgate loading. An extended load transfer distance was shown to potentially reduce loading on pillars adjacent to the longwall as the loading is spread over a larger area. The results of these studies indicate a need for further field verification and research toward regional geologic influences on pillar loading and how these may impact ground stability.

Jan 1, 2013

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By William Kendall

"A tremendous amount of research, analysis, and engineering time is used to design a proper roof support system including the type, length, and location of the roof bolts. Unfortunately, since the roof bolts are being installed under unsupported roof, the exact location for the bolt holes cannot easily be determined and then marked onto the roof. The actual location where the roof bolts are installed is typically left to visual estimates by the operator. This frequently results in either (1) the operator overestimating the space between roof bolts and installing more bolts than required, thereby increasing cost and reducing efficiency; or (2) the operator underestimating the space between roof bolts and installing fewer bolts than required, thereby reducing safety, leading to potential roof failure or possible violations.A patented laser light grid system has been developed by J .H. Fletcher and Monitech, a South African Company, to aid in proper machine positioning in the heading and proper bolt spacing. The system can also show when an entry is over width, requiring additional roof support. The system is relatively simple and inexpensive. The concept is applicable across the full range of roof bolters from low to high seams and from single boom to multiple boom bolters. The system can be configured to meet most bolting patterns.The system consists of several very small 1 milliwatt, class 2, line type lasers that project a line onto the roof. The actual laser is 27mm in diameter x 47mm long (1"" x 1.8""). In South Africa it is approved as intrinsically safe and is mounted inside a 50mm diameter x 64mm long (2""x 2.5"") protective housing. In the USA, we are seeking an X/P approval and the laser will be mounted in a headlight enclosure 110mm diameter x 125mm long (4.3"" x 5""). Fifteen of the systems have been installed in South African coal mines with good results.The system has aided the mines in meeting the bolt spacing tolerance used in the Republic of South Africa, which is typically 15% of the nominal bolt spacing or 7 in for 4-ft bolt spacing. Fletcher has submitted the system to MSHA for approval in the US."

Jan 1, 2016

By Tim Miller, Michael M. Murphy, John L. Ellenberger, Gabriel S. Esterhuizen

"A limestone mine in Ohio has had instability problems that have led to massive roof falls extending to the surface. This study focuses on the role that weak, moisture-sensitive floor has in the instability issues. Previous NIOSH research related to this subject did not include analysis for weak floor or weak bands and recommended that when such issues arise they should be investigated further using a more advanced analysis. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to demonstrate the effect that a weak floor has on roof and pillar stability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface.IntroductionMassive roof falls extending to the surface at a limestone mine in Ohio have been studied collaboratively by the National Institute for Occupational Safety and Health (NIOSH) and the mine owners. This paper provides a summary of the sequence of events leading to observed instability and presents a numerical modeling analysis that investigates the role a weak floor can have on roof and pillar stability.This study builds upon previous NIOSH research in underground limestone mines undertaken by way of a survey that analyzed performance of pillars in 34 different stone mines in the Eastern and Midwestern United States between 2005 and 2009 (Esterhuizen et al., 2011). This survey led to the development of underground stone mine pillar design guidelines based upon a “stability factor” for the pillar system. The factor is compared to operational experience to determine ranges of values that are typical of stable pillar systems. A software package titled Stone Mine Pillar Design (S-Pillar) was developed for easy application of these guidelines (Esterhuizen and Murphy, 2011).Weak floor in the present case study departs significantly from cases included in the previous NIOSH research, in that none of the 34 study mines had weak floor issues. Moreover, this case study is the first in which a weak floor has been monitored routinely as roof falls are occurring. A detailed report on the observations and measurements taken at the mine has been published (Murphy et al., 2015). The previous observations led to the conclusion that although there were weak bands in the pillar, the weak floor was the significant defect that led to the instability issues. The pillars were initially mined in 2004, approximately 10 years before the instability issues began to occur. The objective of this study is to use numerical models to analyze a variety of floor strengths and the impact of moisture content to find the critical point at which the floor becomes unstable, leading to long-term instability issues."

Jan 1, 2015

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By Yuanfei Chen, Jianfeng Zha

"China is the largest producer and consumer of coal in the world. The mining-induced surface subsidence has bad influences on the surface and structures above the surface. In order to minimize disasters, removal, reinforcement, or maintenance structures are often adopted. In the application of maintenance methods, it is necessary to carry out dynamic surface subsidence prediction to choose maintenance methods, optimize maintenance time, and evaluate the amounts of work. Time series methods and influence function methods are common for dynamic surface subsidence prediction, but the former is difficult to consider with underground mining conditions, and the latter has low prediction precision. Therefore, this paper develops a dynamic subsidence prediction model aided by field-measured data and realizes the model programming. The model could achieve high-precision prediction of dynamic surface deformation through optimizing the parameters in time by using field-measured data of surface subsidence. The research results of engineering cases show that, with the method of dynamic prediction, the standard error can be controlled in the range of 5%, greatly improving the accuracy of dynamic prediction of mining subsidence, which provides strong technical support for the maintenance and management of structures. INTRODUCTION With the rapid economic development and continued industrialization process, the demand for energy is growing in China. Today, China is one of the largest coal, oil, and gas consumers in the world. Coal consumption accounts for 47.7% of the total consumption in the world (Tian, 2016). In order to meet the demand for coal resources in the process of modernization, more and more coal mines carry out coal mining under villages, buildings, highways, and bodies of water. The mining-induced overlying strata and surface subsidence have bad effects on surface and on various structures (such as buildings, railways, highways, high-tension transmission lines) and could even cause various disasters (Williams et al., 1998; Bell et al., 2000; Doyle et al., 2002). Generally, methods, such as removal, reinforcement, or maintenance are taken to eliminate the adverse impacts (Kraatz, 1984; Bell and Genske, 2001; Wang, 1989). When reinforcement or maintenance is selected to remove bad effects, the proper maintenance methods must be chosen. In addition, maintenance time, as well as an evaluation of time it will take to do the work are necessary to predict the surface subsidence with high precision."

Jan 1, 2017

By Jun Lu

The Pittsburgh seam is the most extensively mined coal bed in the Appalachian Basin. Unlike most other prominent coal seams, the Pittsburgh seam typically includes a sequence of immediate roof coals and intervening rock binders (or ?draw slate?), most of which are within mineable horizons. Furthermore, unlike the main bench, the thickness of the overlying roof coals and their intervening rock binders can vary significantly. For instance, in southwestern Pennsylvania, the Pittsburgh seam main bench typically ranges from about 5.0 to 6.0 feet thick with minimal variation over short distances. On the other hand, the Pittsburgh seam roof coals and immediate roof binder typically range from a few inches to several feet, and in certain geologic settings can vary significantly over short distances. Additionally, in some locations, very thick draw slate can totally replace the roof coals. Since the draw slate, which typically consists of claystone or clayladen shale, is relatively weak, the presence of thick and variable draw slate in the roof and rib can significantly affect mine safety and productivity. This paper presents the adverse effect of thick draw slate on a 1500-foot-wide longwall face in a southwestern Pennsylvania coal mine. Mapping of the thick draw slate, numerical models which illustrate stress distribution and failure associated with thick draw slate, and operational adjustments instituted to mitigate the negative impact of thick draw slate will be discussed in detail.

Jan 1, 2013

By Timothy Batchler

"Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance.This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) as part of manufactures' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs dual-walled bag designs to the support capacity, stiffuess, load shedding events, and yield characteristics.INTRODUCTIONDeveloped in the 1990s, the first major use of pumpable supports systems in U.S. longwall operations was in the support of bleeder entries (Barczak, Tadolini, 2008). Since then, they have been utilized as yieldable concrete supports to provide a safe working environment for longwall mining gateroads, bleeders, and emergency escapeways while also maintaining adequate ventilation pathways. The basic structure of pumpable roof supports has remained unchanged over the years. Formed in place with a twopart fast-setting grout, the support material can be pumped into a containment bag from several thousand feet away often through surface boreholes. The containment bag then acts as a form to fill the support and provides confinement to the grout during loading and after failure. Pumpable roof supports provide full contact with the mine roof and floor, which eliminates the need for secondary material to establish proper roof contact (see Figure 1). They provide a high peak load capacity and a sustained, confinement controlled yield behavior while maintaining stable ground conditions, which is essential to underground mining operations."

Jan 1, 2016

By Stephen C. Tadolini, Minova USA Inc., Peter S. Mills, David R. Burkhard

"Fiber-reinforced spayed concrete has been used for several years in civil and tunneling operations. Research conducted to reduce cure times and increase compressive and flexural strengths resulted in the development of Tekcrete Fast®, a cementitious product capable of obtaining 41 MPa (6,000 psi) compressive strength and 8 MPa (1,200 psi) flexural strength in only 3 hours and reaching 7 day strengths of 62 MPa and 11.7 MPa (9,000 and 1,700 psi), respectively. A single bag product that uses conventional shotcrete and gunite application systems make it a natural crossover product for mining applications. The discovery of incredible adhesion properties and high resistance to chloride permeability helps ensure long-term stability and increases the ease of application. Project results from Disaster City® in Texas and the application for rehabilitating a coal mine belt entry are presented. The case study illustrates the effectiveness of the product in stabilizing a coal mine beltway and adjacent cross-cuts that were subjected to progressive sloughage due to humidity and cyclical loading. INTRODUCTION Original research produced a shotcrete formulation that extends beyond stabilization and can be used to restore the structural integrity of damaged infrastructure. The primary challenge was to develop a shotcrete or gunite that had structural strength within a few minutes to prevent parasitic loading, allowing ingress into damaged structures minutes after applying the mix formulation. This also applies to mining conditions where rapid support of progressive failures can minimize failure. An additional benefit was discovering that the product had extremely high adhesion properties in addition to high flexural strengths. The approach to product design was the development of “single bag” dry mixes that are entirely self-contained, can be rapidly transported anywhere in the field or underground, and can be deployed using simple equipment. Dry mix eliminates issues relevant to high shear water mixing because water is added in the form of a mist at the point of delivery; thus a low water-to-cement ratio can be achieved. However, since there is no onsite powder mixing, the product must have a high degree of inherent homogeneity. Minova offers a commercial version of this material, Tekcrete Fast®, a product that has been successfully deployed in the mining industry and is currently being used in civil, construction, and tunneling operations. The material can rapidly stabilize lose ground in metal, nonmetal, and coal mines. This paper described the technology development, product testing results, and applications and describes a case study to stabilize a coal mine beltway."

Jan 1, 2017

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By Madan M. Singh

Mining under bodies of water such as oceans, lakes, rivers, streams, ponds, and other impoundments, is not a new technique. However, in the United States it has been fairly restricted to date. In order to recover the maximum amount of the nation's reserves, in the future, it is important that further mining under such bodies of water be planned. However, it is imperative that this is not done at the expense of danger to the nation's miners or appreciable property damage. If all the bodies of water are considered large, and it is assumed that these constitute a hazard when mining in their vicinity irrespective of their size and geometry, a significant percentage of the coal reserves are likely to be sterilized. How- ever, by adopting special mining plans and procedures, it may be possible to release reserves for exploitation that would otherwise be unmineable since the surface of bodies of water below which they lie are relatively small in size. In 1977, the Bureau of Mines issued Information Circular (IC) 8741, entitled "Results of Research to Develop Guidelines for Mining Near Surface and Underground Bodies of Water". This document was based on the work done by Skelly and Loy (under Contract No. H0252083) and K. Wardell and Partners (under Contract No. H0252021). How ever, these guidelines have limited application, because these did not (1) define the bodies of water of concern, and (2) take into account the nature of the strata being encountered. These guidelines assumed that all bodies of water which would be undermined were large. For the purposes of this discussion, water bodies may be divided into three categories, depending upon their potential to cause damage to the underlying mining activity: ? catastrophic ? major ? limited Bodies of water which pose the threat of catastrophic destruction in the mine, should there be an inrush, include oceans, large lakes, big inland reservoirs, and rivers that could flood the mine complete- ly in a short period. Those with major potential for damage would include lakes and streams which might present a danger to both life and property if not considered in the mining plans. Finite bodies of water which have a volume considerably smaller than the mine volume offer a limited potential for damage in the case of an inrush. These include flowing streams which have a relatively small rate of replenishment and which can be dealt with by pumping or isolation in the event of a breakthrough into the mine. Such bodies of water may be inconvenient and cause a temporary disruption of production, and could even cause some damage to equipment, but only in rare instances would personal injuries occur. The scope of this paper is limited to the exploitation of stratified mineral deposits with overlying -face bodies of water. Vein and dessiminate ore deposits are not discussed, nor are breakthroughs into adjacent mines in the same horizon. Overlying, water-logged strata also pose a serious threat to mining, but are not treated in this discussion. Pending further investigation these strata may be considered as bodies of water with catastrophic potential for damage, with the base of the strata being considered the bottom of the water body. When the body of water is large, so that it may cause catastrophic damage to the mine in the event of an inrush, the guidelines suggested in IC 8741 are applicable. In order to develop criteria and procedures for mining under smaller bodies of water, however, it is necessary that the nature of the strata disturbance due to underground mining be examined.

Jan 1, 1981

By Chaojun Fan, Du Wenzhang, Sheng Li, Hong-Hong Shi

"Coal and gas outburst is an extremely complex dynamic disaster in coal mine production process which will damage casualties, equipment facilities and disorder the ventilation system by suddenly ejecting a great amount of coal and gas into roadway or working face. This paper analyzed the interaction among the three essential elements of coal and gas outburst dynamic system. A stress-seepage-damage coupling model was established which can be used to simulate the evolution of the dynamical system, and then the size scale of coal and gas outburst dynamical system was investigated. Results show that the dynamical system is consisted of three essential elements, coal-gas medium (material basis), geology dynamic environment (internal motivation) and mining disturbance (external motivation). On the case of C13 coal seam in Panyi mine, the dynamical system exists in the range of 8-12 m in front of advancing face. The size scale will be larger where there are large geologic structures. This research plays an important guiding role for developing measures of coal and gas outburst prediction and prevention. INTRODUCTIONCoal and gas outbursts are a complicated mine gas dynamic phenomenon that pose a serious threat to coal mine safety production. Since the first recorded coal and gas outburst occurring in Isaac coal mine of the Lule coal field in 1843, more than 40,000 outbursts have occurred in the world. China ranks first in outburst frequency and intensity. In recent 20 years, China on average increases 37 pairs of coal mines and more than 280 times outburst accidents every year (Yan, 2013). The coal and gas outburst occurred on Oct 20, 2004 in Daping Coal Mine, Zhengzhou Coal Group, caused serious gas explosions and ejected 1,894 tons of coal into the face, causing 148 fatalities. In recent years, despite implementation of numerous control measures, coal and gas outburst still occur frequently ash mining depth and mining intensity increase. The outburst mechanisms can be summarized in the following four aspects: the gas leading role hypothesis, the geostress leading role hypothesis, the chemical effect hypothesis, and combination hypothesis. The last hypothesis has won the acceptance of most scholars who consider that an outburst is the result of combined effect of stress, gas and coal (Yu, 1992).Numerous experimental measurements and numerical simulations were conducted to investigate the permeability and damage development process in coal seam. Sobczyk, et al (2011) carried out a laboratory research of the influence of sorption processes on gas stresses leading to coal and gas outbursts. Wang, et al (2013, 2015) conducted laboratory experiments to investigate the rapid decompression and desorption induced energetic failure in coal using a shock tube apparatus. Xu, et al (2006) developed a coupled gas flow and solid deformation numerical model and applied to simulate the coal and gas outbursts in underground coal mines using RFPA2D-Gasflow. An, et al (2013) and Xue (2014) analyzed major parameters and the effect of gas desorption on outburst initiation and established a model of gas migration and mechanical processes during excavation."

Jan 1, 2016

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Takashi Sasaoka, Hiroshi Takamoto, Akihiro Hamanaka, Pongpanya Phnthoudeth, Hideki Shimada, Jiro Oya

"Indonesia is the second largest coal exporter to Japan, accounting for about 30 Mt annually. They produced over 400 Mt in 2015, over 99% of which is from open-cut mines. However, the conditions of surface mining are becoming worse year by year: the stripping ratio is increasing, the economy is worsening, and the infrastructure for coal transportation from inland mining areas is not being maintained. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. In consideration of growing need, our research program is conducting a study on the potential for an underground coal mine in Indonesia. This research is being done through the roadway heading research program, which is looking into developing an underground coal mine from an open pit highwall. The greatest challenge for underground coal mine development in Indonesia is the maintaining the safety of the mine roadway during heading because the roof rock is exceptionally weaker. There is a potential for heading below mobile, unconsolidated soft sediment, and instead mining a deep area. This increases the likelihood for problems in the stability of the support system due to increasing ground pressure. The ground behavior around the roadway was measured using telltales, extensometers, and convergence measurements. Moreover, rock property tests were also conducted on exploration drilling cores. Based on the geological dates and monitoring data, a series of numerical analyses were conducted in order to assess support needs in the main roadway under different depths. Results of numerical analyses indicate that the current arch support design is effective when the mining depth is lower than 100m. However, if the mining depth is larger than 100m, the current arch support design should be changed to include the application of higher yield strength material, shorter spacing, etc. Moreover, bolting may also be useful if ground pressure is high locally. Based on a series of measurement data of ground and support behavior, a control criterion for main roadways under weak geological conditions is proposed in this paper."

Jan 1, 2017

By Syd Peng

"As the International Conference on Ground Control in Mining (ICGCM) enters its 35th year in 2015, it is time to look back and identify the areas that need to be emphasized and to look forward to see what areas need to be researched in the future. In the past three decades, ground control has made a tremendous advancement, and many case studies published in the 36 volumes of proceedings have demonstrated its important role in the daily mining operations. However, there is still plenty of room for improvements. This paper discusses the research needs in 12 subject areas, including mine geology, rock property, zones of disturbance in overburden, computer modeling, underground stress measurements, research method, roof bolting, coal pillars, failures, subsidence, shield supports, and coal bumps.INTRODUCTIONThe International Conference on Ground Control in Mining (ICGCM) was founded in 1981. Since then, 1,546 papers have been published in the 36 conference proceedings, including the three surface subsidence workshops held in the 1981, 1986, and 1992. All types of topical areas regarding mining, from geotechnical core loggings in the exploration phase through backfilling after mining to finally spoil piles stability on the surface, have been addressed. A review of these papers, and other related literature as well, indicate that ground control has developed to become an inseparable part of mine design and a problem-solving tool for safe production.After 34 years, it is time to look back and identify the areas that need to be emphasized and to look forward to see what areas need to be researched in the future. There is no doubt that the conference series has achieved the goal for which it was originally designed: to provide an annual forum for the exchange of information among the researchers, government regulators, equipment manufacturers, consultants, service providers, and—above all—mine operators. There have been many papers addressing the application of ground control techniques for successful mine design and safe production, and, without these papers, many projects would have failed. In fact, the conference emphasis on application types of papers may have steered too far toward the application side. A review of the conference papers shows that papers have been leaning mostly toward the applied side, leaving most, if not all, fundamental issues behind in nearly every topical area. This paper addresses research needs in 12 topical areas: mine geology, rock property, zones of disturbance in overburden, computer modeling, underground stress measurements, research method, roof bolting, coal pillars, failures, subsidence, shield supports, and coal bumps."

Jan 1, 2015

By Joao Felipe Costa, Jair C. Koppe, Andre Zingano, Cleber Gomes

"Run-of-mine Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. A large amount of waste results from the coal preparation, and it must be disposed of in waste piles or waste dams, depending on the material size. These waste disposals are the cause of serious environmental problems, not only in the short and medium terms, but mainly in the long term, due to the risk of provoking acid drainage or spontaneous combustion. Waste disposal requirements also demand large areas. Other problems include the pillar and roof stability in abandoned and mined out areas, building of edifices on the old and active mines, and mining under urban areas. To solve these problems simultaneously, backfilling the entries in mined out areas began with two objectives: to understand the mechanical behavior of the filling material and to model the backfilling of room-and-pillar coal mine entries through numerical simulation. Laboratory tests were performed for different filling material (with and without cement) to determine its mechanical properties and failure criteria. Based on this study, it was possible to conclude that the backfill method is a good strategy to improve the ground stability in room-and-pillar coal mines for the long term, especially for weak coal seams, and to reduce the quantity of material on waste piles on the surface.INTRODUCTIONRun-of-mine (ROM) Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. Two types of waste are associated with power plants that bum coal for energy generation: 1) the waste from the coal preparation plant and 2) the ash from the power plant after coal burning.The Brazilian coal ash content in the ROM coal is between 45 and 55%. The clean coal is 20 to 30% ash for 4,500 kcal/kg (18,000 BTU). The coal preparation plant recovery is only about 35%. Santa Catarina State (SC) produces about 7 million tons/year of ROM coal, which results in a total of 4.5 million tons of waste. This is a large amount of waste that must be disposed of in waste piles or waste dams, depending on the material size. The waste and ash content is represented by silicate materials, such as clay and sand, and by sulfide materials, like pyrite and organic sulfur (between 1and5%)."

Jan 1, 2010

By Wojciech Masny, Andrzej Walentek

"The most common extraction method in Polish coal mines utilize pillars between adjacent longwall panels. This is mainly due to the significant depth and difficulties in maintaining stability of the gateroads. This paper presents measurements of entry convergence and range of the fracture zone around a gateroad measured with a borehole camera. The entry where the measurements were taken was located in a parallel entry separated from the gateroad by a 5-m- (16-ft-) wide pillar. The gateroad was located in a hard coal seam 900 m (2,952 ft) deep with a dip of 5°. The extraction method was longwall mining with caving and the mining height was about 3 m (10 ft).Furthermore, the ""in situ"" measurements were compared to the convergence forecast for the gateroad and fracture zone by means of numerical modeling conducted using the Phase2 Version X.X finite element program from Rocscience. The determination of the fractured zone around the openings is of great importance to successful mining practice, especially in support planning and design for longwall gateroads. Moreover, proper determination of the fractured rock zone is one of the basic elements in the process of planning the roof bolting for mine workings.INTRODUCTIONIn the Polish. hard coal mining sector, retreat longwall extraction is most commonly used (Prusek and Masny, 2007). This method is connected with the necessity to carry out a number of development operations during the first stage, including among others, driving of gateroads and a setup room.Currently, most Polish mines eliminate gateroads behind the extraction front, using the ""U"" ventilation system (Szlitzak et al., 2008). In such cases, one of the roads for the next longwall panel is driven along the caving goafs, leaving a protective pillar of some chosen width (Figure 1). The question regarding the width of the coal pillar is especially important to the stability of the gateroads that define the panel for the subsequent longwall. When analyzing the previous experience relating to this type of pillar (Junker, 2006; Rajwa, 2008; Stranzet et al., 1973; Betriebsempfehlung, 1982), one can state that there exist two solutions for the determination of its width."

Jan 1, 2010