Search Documents

By Peiye Yan, Huiqing Tang

To reduce coke consumption in blast furnace ironmaking, this study proposed a new method of applying iron-coke briquette prepared using hematite powder and pulverized coal to protect coke in BF iron making. Results showed that, with a ratio of hematite to coal of 2.0, the iron-coke briquette could obtain a satisfying compressive strength of more than 1500 N both before gasification and after being gasified by CO2 for 1 h. The activation energy of the iron-coke briquette was 93–135 kJ/mol, which is lower than the coke and therefore could protect the coke in BF. The agglomeration and stratification of iron particles occur in the course of iron-coke briquette gasi fication and is bene ficial to the improvement of the iron-coke briquette strength.

Mar 1, 2018

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

By James C. Sever

The mode of operation of dolomite kilns at a magnesium reduction plant using the Magnatherm process was designed to minimize operation cost and maximize kiln refractory life. Analysis of downstream operation issues shows the quality metric for dolime changed from loss on ignition to specific surface area. This produced a complete change in kiln operation; the net results being major plant productivity increases decrease in operating cost, and increases in both kiln operating costs and reline frequency.

Jan 1, 2015

By Y. Waseda, S. V. Gnyloskurenko

"Present paper reviews the various processes for making of metallic foams. These methods are classified in accordance with the state of initial metals - liquid, powdered and ionized. Liquid metal can be foamed by direct inputting of gas into melt, using gas releasing foaming agents or producing supersaturated metal-gas solutions. This group also includes methods creating voids in the melt. Powder route is based on using powdered matrix metal with foamable precursor materials. Finally Deposition techniques allows making highly porous metallic structures using ionized metal.Experimental study presented shows importance of wettability in bubble formation at gas blowing into melt simulation liquid (water) through holes. Good wettability of injection holes by water ensures formation of bubbles with smaller sizes that effect to the final foam structure.IntroductionOne of the objectives of future production technology is to make of lightweight constructional materials while achieving improved property and good economy as well.The most perspective lightweight materials are cellular or foamed materials that are Wide8pread. in nature and have a growing interest in industry and everyday life.Even metals and metallic alloys can be produced as cellular solids or metal foams beside of the traditional engineering materials such as polymers, ceramics or glass. Recent developments in metal foams, especially aluminium, have produced a new class of lightweight materials."

Jan 1, 2000

By P. Myllykoski, J. Nylander, A. S. Korhonen, J. Larkiola

The coefficient of friction and the deformation resistance have been determined from the measured rolling parameters by applying the Bland-Ford-Ellis rolling force model and the artificial neural network model (ANN). The dependence of friction on the parameters such as reduction, rolling speed, front and back tensions, contact pressure and deformation resistance have been studied by the ANN model. Measured data of over 10 000 coils have been used in the training stage. Various dependencies have been examined and the results show that the friction coefficient does not depend much on the rolling speed. The reduction and deformation resistance seem to have the strongest effect on the friction coefficient. A friction model based on neural computing has been included into the existing rolling force model.

Jan 1, 1994

By Tianyou Huang, Yuan Lu, Haimin Long, Jinwu Kang, Gang Nie

"The distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and less or no machining allowance, especially for large but thin steel castings such as heavy turbine blades. In the paper, a method is proposed to control the distortion by adjusting heat transfer coefficient of metal parts during heat treatment process. Required heat transfer coefficients can be realized by getting the metal parts into contact with various media such as water spray, insulation felt or materials with different heat conductivity. The control method based on this idea is set up and achieved. By using insulation felt and water spray to change the heat transfer coefficient during the stages of heat treatment process, the results indicate that the proper control time and vary with materials.IntroductionThe distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and to realize less or no machining allowance [1]. For example, the Three Gorges turbine blade’s distortion is as large as 50mm during heat treatment process. The uneven heating and cooling during heat treatment process is the main reason for distortion [2]. By adjusting heat transfer coefficient of different areas of metal parts, the heat treatment process could be controlled. The temperature variation, direct cause for distortion, could be under control. Loeser Klaus used high pressure gas to achieve uniform heat transfer during gas quenching and proposed the possibility to use ""Dynamic Quenching"" processes where the quenching severity is varied during quenching by stepwise control of either gas velocity or gas pressure [3]. Li Zhichao also suggested minimizing distortion by marking a component into several areas and imposing different heat transfer coefficients on each area [4]. Heat transfer coefficient can be controlled by getting the metal parts into contact with different media such as water spray, insulation felt, air or different heat conduction materials. In addition, the exact time to adjust the heat transfer coefficient is another factor for distortion. A method is presented in this paper by actively adjusting heat transfer coefficient for different areas of metal parts and different stages of heat treatment process to control their distortion. The corresponding experiments have been made by using different metal materials."

Jan 1, 2012

By R. Padilla

In most of the Chilean copper and gold concentrates, arsenic is present mainly as enargite, Cu3AsS4, which at the conventional roasting or smelting temperatures decomposes liberating arsenic as gaseous compounds. The objective of this investigation was to study the decomposition reaction of enargite in an inert atmosphere in the range of 500 °C - 750°C. The results obtained indicated that the decomposition begins at about 525 °C. Two distinct regions in the temperature dependence of the decomposition rate were observed: a low temperature region between 525 °C to 650°C and a high temperature region between 650 °C to 725 °C. The X-ray diffraction analysis suggests that the decomposition of enargite occurs through the formation of intermediate tenantite, according to the following sequential reactions: 4Cu3AsS4(s) ? Cu12 As4S13(s)+ 3/2S2(g) Cu12 AS4S13(s) ? 6Cu2S(s) + 2As2S3(g) + 1/2S2(g) The decomposition kinetics was analyzed by using the model for a topochemical reaction of spherical particles: 1-(1-X) 1/3 = kt, which represented well the data. Apparent activation energies of 113 kJ/mol and 60.5 kJ/mol were found for the low and high temperature regions, respectively.

Jan 1, 1999

By A. Mukhopadhyay

Gas stirring, simultaneous arcing, chemical additions are some basic steps in the secondary steel making. From tap to team however, there are enough uncertainties and several in-situ decision making required to match the fmal composition and temperature in the given amount of processing time. Currently available control algorithms rely on overall material and heat balance coupled with a self-learning regression based tuning of model constants. In this paper we demonstrate the capabilities of Computational Fluid Dynamics (CFD) in modeling and analyzing the thermo-chemical aspects of secondary Steelmaking. These models take advantage of scientific and engineering advances in computational tools and provide almost real time speed of analysis. This can be a very effective tool for operator training, process debugging and improvement as well as new innovations. Keywords: Argon purging, Secondary steelmaking, Arcing, Ladle Furnace, Process Control.

Jan 1, 2003

By Mitsuru Tanahashi

In order to develop an effective process for the production of from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at a solar-grade silicon (SOG-Si) 1773K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten M6-8 followed by oxygen gas injection into the melt (Two-stage connecting process). II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection Process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By N. Kanari

Kinetics of the carbochlorination of Cr2O3 has been studied with C12+CO gas mixtures between 500 °C to 900 °C using thermogravimetric analysis. The apparent activation energy is about 100 kJ/mol. Mathematical fitting of the experimental data suggests that the shrinking sphere model is the most adequate to describe the carbochlorination mechanism of chromium oxide and that is controlled by the chemical reaction. In the temperature range of 550 "C to 800 OC, the reaction order is about 1.34 and is independent of temperature. Changing the C12+CO content from 15 pct to 100 pct increases the reaction rate and does not affect the reaction mechanism. Similarly, changing the ratio of C12/(Cl2+CO) from 0.125 to 0.857 do not modify the carbochlorination mechanism of Cr203. In these conditions, the reaction rate passes through a maximum when using a chlorinating gas mixture having a Cl2/(C12+CO) ratio of about 0.5.

Jan 1, 1998

By Shabnam Sabah, Geoffrey Brooks

In oxygen steelmaking, splashing and droplet formation play a key role in the kinetics of the process. Though splashing has been studied by previous investigators, there is only limited understanding of how different cavity modes affect splashing. Therefore, a cold model study (at various lance heights and gas flow rates) has been carried out focusing on the issue of cavity modes and how it affects splashing phenomenon. Analysis using Fast Fourier Transform (FFT) was carried out on cavity oscillation that showed that frequency and amplitude of oscillation was highest in penetrating mode. Measurements of splashing over a range of conditions showed splashing greatly reduced when cavities went from splashing to penetrating mode. The results were validated and compared with plant data and previous model investigations.

Jan 1, 2014

By J. M. Rapkoch

In late October 1996, an acid plant at a major U.S. copper smelter was faced with unexpected and rapidly increasing pressure drop across the gas cooling tower in the acid plant, indicating a build-up on the packing. This threatened to halt operations if not resolved. Earlier that month, a smaller vessel in the acid plant was found to be completely plugged with lead sulfate. It was feared that a similar fate awaited the gas cooling tower unless the scale build-up was stopped. Although lead sulfate is present in most copper smelter acid plants, this accumulation was unusually severe. An investigation was launched to find the source of the lead, determine how lead is transported to the gas cooling tower, recommend operating practices to prevent such severe scaling, and seek ways to recycle the lead value in the scale covered polypropylene packing. Late in the investigation it was learned that the lead originated from an improperly executed recycling program.

Jan 1, 2000

By U B. Pal

Downsizing and decommissioning of nuclear facility operations is increasing the stockpile of various different grades of Radioactive Scrap Iron (RSI). Disposal of this material not only represents significant resource and value lost, but also necessitates long term monitoring for environmental compliance. The latter results in additional recurring expense. It is desirable to be able to decontaminate the RSI to a very low level that can be recycled or used for fabrication of containers for RSI disposal instead of using virgin metal to fabricate the container. Electro-Slag Remelting and Refining (ESR) is often used for decontaminating radioactive contaminated sources of scrap iron such as stainless steel. Non-radioactive oxides of cerium are used to simulate the radioactive oxide contaminants of Uranium and Plutonium. The success of the ESR process is strongly dependent on the capacity of the slag to rapidly incorporate the radioactive contaminant (simulant). In this study we have measured the slag-metal partition coefficient for cerium and investigated the reaction mechanism for the dissolution CeO, in the slag.

Jan 1, 2002

By R. E. Sundell, S. M. Correa

"A mathematical model is developed for the fluid flow in tungsten-inert gas weld pools. The fluid is taken to be incompressible, viscous, electrically conducting, and confined within a pool of specified shape. The flow is driven by surface-tension gradient (thermocapillary), electromagnetic, and buoyancy forces generally in this order of importance. Analysis indicates that the electromagnetic field may be calculated a priori and so decoupled from the nonlinear fluid mechanics and heat-transfer problem. The resulting set of equations is solved numerically by a line relaxation process. Computational errors caused by truncation in finite-difference schemes and by inadequate grid distributions are considered. The model is used to study several cases of differing heat and current input to the pool with and without surfactant-induced thermocapillary forces. The principal conclusions are that the thermocapillary flow, when present, is dominant with surface velocities on the order of 1 m/s. The heat transfer, as deduced from isotherms within the pool, is crucially dependent on the flow. Also, flow velocities and weld-pool surface temperatures were measuredand agree well with the model.2. IntroductionThe requirements of improved control and of automation in the TIG (tungsten-inert gas) welding process have led to the development of mathematical models for the heat transfer to the workpiece. It is now widely recognized that the fluid flow in weld pools sufficiently distorts the conduction heat transfer pattern to warrant inclusion in a process model. The experiments of Woods and Milner (1), among others, demonstrated that TIG weld pools could be driven by the electromagnetic J x B body forces present, J being the current distribution and B the induced magnetic field. Atthey (2) calculated that in typical pools the buoyancy force was about an order of magnitude less important - despite the large temperature gradients present - and neglected it in a computational study of the magnetohydrodynamic (MHD) flow. This work also reviewed many earlier studies of MHD flow caused by a source of current at a fluid surface, including analytical studies by Shercliffe (3), Sozou (4), and Sozou and Pickering (5), and a numerical study by Andrews and Craine (6). These works establish the importance of the electromagnetic force in the weld-pool flow."

Jan 1, 1986

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By W. Dutton, D. Simms

"The clearing of tuyeres on copper and nickel converters or similar metallurgical, vessels has, for many years, been done using mainly a manually- operated ""puncher"". One such device is the ""Gaspe Puncher"" developed in 1962 at Noranda's Gaspe Smelter. In an attempt to remove the operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor.The automated puncher is controlled by a Texas Instruments Model 530C Programmable Controller (PLC). Position measurement and control is done using non-contact position measuring equipment from the Tele-Controls Division of Geodimeter Inc. The entire automation system was installed on an existing Gaspe Puncher with minimum disruption to the operation of the smelting process. The operator's panel allows the user to ""block out"" any individual tuyere, and to select any of a variety of operating modes.The development of the automated puncher is described, and the results of several months operation are given.IntroductionThe tuyeres of copper and nickel converters and similar metallurgical vessels become blocked with solidified material formed by the cooling action of the blowing air. This restricts the converting operation. Clearing these blocked tuyeres has for many years been done mainly using a manually-operated ""puncher"" which uses a hydraulic or pneumatically-operated piston to drive a steel bar into the tuyere. The Gaspe Puncher, developed at Noranda's Gaspe Smelter in 1962 is one such device. It is currently being built and sold by Heath & Sherwood (1964) Limited, under license to Noranda. There are over 200 units in operation world-wide.In an attempt to remove the Puncher operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, and to increase productivity, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor. This paper describes the development of the automated Gaspe Puncher, its installation at the Horne Smelter, and the results of its operation after several months."

Jan 1, 1989

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By S. Viswanathan, A. S. Sabau

"Dimensional changes between a pattern die and its corresponding investment casting part occur as a result of complex phenomena such as thermal expansion/contraction and hot deformation (elastic, plastic, and creep) during the processing of the pattern material (wax), mold material (shell) and solidifying alloy. Determining the pattern tooling dimensions is crucial to the dimensional control of the investment casting process. To date, computational methodologies have not been applied to the prediction of dimensional changes in investment castings.This paper deals with the evaluation of wax pattern dimensions, which is one important factor in determining pattern tooling dimensions in investment casting. Cerita 29-51, an industrial wax, is considered in this study. The wax pattern dimensions are determined by considering its thermo physical and thermomechanical properties, restraint of geometrical features by the metal die, and process parameters such as dwell time, platen temperature, injection pressure, and injection temperature.IntroductionThe investment casting process involves making a disposable wax pattern by injecting wax into a metal mold, building a ceramic shell mold around the wax pattern by the application of a series of ceramic coatings to the wax pattern, dewaxing the ceramic shell mold, and casting the alloy into the shell mold. Dimensional changes between the pattern tooling and its corresponding cast part occur as a result of thermal expansion, shrinkage, hot deformation, and creep of the pattern .material (wax), mold material (shell), and solidifying alloy during the processing [1]."

Jan 1, 2001

By D. Donald Downey

Pilot Testing Ion Exchange Resin (IEX) can go from very simple beaker testing to complicated column testing. Space velocities, regenerant quantities, loading capacities, ion leakage, are all terms that get accumulated together to prove or disprove a resin’s (or resins’) ability to load a single ion (or specific set of ions). Not getting all the resin’s operating parameters correct will disqualify (or at least skew) the results. Laboratory tests for capacity, moisture content, bead size, metals fouling, etc.—what does it all mean? At last count, there were over twenty-five separate ion exchange resin tests (analyses) that were available to end users. Standard testing procedures identify the resin properties but more specific procedures can be used to identify problems with equipment operation. Then, there are the costs to consider; simple cation resin testing (moisture content, total capacity and bead integrity) is in the $200/sample range. However, add to this Chatillon, Russian Ball Mill Test, HIAC particle size, metals and % regeneration test procedures and the lab work can increase to over $1000/sample. In this paper, the author will explain the “must-do” pilot and test procedures and why they are important and the key to understanding how resin performs ion exchange.