Search Documents

By Kunihiko Takahashi, Gjergj Dodbiba, Hisayoshi Umeda, Toyohisa Fujita

"An increasing number of mobile phones is increasing the number of the discarded mobile phones. Many efforts are thus being made to collect and recycle these devices. This paper is a short introduction of the recycling system of precious metals from the discarded mobile phone, currently available in Japan. Moreover, an attempt has been made to compare the energy recovery and the mechanical recycling of plastic wastes from the discarded mobile phone. The assessment has been carried out in the context of the life cycle assessment methodology (LCA). The environmental impact of each option was assessed by calculating the following impact indicators: depletion of abiotic resources (ADP), and global warming potential (GWP). 1. Introduction In 2003, the demand for mobile phones was increased since the camera was included in a mobile phone and the 3rd generation of mobile phones was introduced. In turn, the number of discarded mobile phone is rising sharply. Generally speaking, all the metallic parts of mobile phones can be recovered and recycled by using smelting and purification techniques. The recycled materials are then used to fabricate other new products."

Jan 1, 2008

By Mark Jolly

"Over the last ten years or so many man hours have been dedicated to developing methods for simulating shape casting processes. The majority of the methods developed have been devised by a combination of computer, mathematics and materials specialists often with limited knowledge of foundries and foundrymen. As a result of this it would appear that although there are many software packages for the foundryman to use there still exist fundamental misunderstandings as to their usefulness and suitability within the foundry.The paper aims to identify how well current software packages perform. The relationships between physical phenomena, practical defects and software capabilities are presented. Some discussion of the use of criteria functions is also presented. Finally issues arising from the postprocessing of results are discussed as the presentation of the results to the lay-person in simulation techniques is possibly one of the most important aspects in influencing the adoption of this type of software in the foundry community."

Jan 1, 1999

By M. A. Barakat

"Adsorption of heavy metal ions specifically, Cu(II), Zn(II), Mn(II), and Cr(VI) from aqueous solution on synthetic 4A Zeolite was evaluated. The 4A zeolite was synthesized previously by dehydroxylation of low grade Kalabsha Kaolin at 800 °C, and reacted hydrothermally with 2-4 M NaOH solution at 100 °C for 2h. The adsorption capacity of the metal ions were found to be strongly dependent on pH and initial metal ion concentration. At the optimium conditions the adsorption capacity decreased in the order Cu(II) > Zn(II) > Mn(II) > Cr(VI) ions. Almost complete adsorption was achieved for both of Cu(II) and Zn(II) ions at pH > 6, while the adsorption capacity for both Mn(II) and Cr(VI) was 96, and 55.3 % at pH 11 and pH 3, respectively. The results also showed that the grain size of the 4A zeolite has a little effect on the adsorption capacity. The experimental data was compared with two adsorption isotherms, Langmuir and Freundlich isotheroms. The results showed a good agreement of the Langmuir plots with the experimental data.1. IntroductionSeveral industrial wastewater streams may contain heavy metals such as Cr, Cu, Pb, Zn, Co, Ni, Mn, etc. including the waste liquids generated by metal finishing or the mineral processing industries. Heavy metals are considered hazardous pollutants due to their toxicity, even at low concentration, and nonbiodegradability. Increasing level of heavy metals in natural water bodies poses a serious threat to all living species including humans. It is, therefore, essential to reduce the heavy metal concentration in effluents/wastewater before it is discharged into the water bodies [1]."

Jan 1, 2008

By John A. Herbst

Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen and the coordination of all unit operations in pursuit of the highest performance level. However several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of Unit operations to account for critical interactions within and 'between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that 'knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significantly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated With the models and can be effectively optimized. Financial goals seems to be the objectives of choice. This paper discusses recent progress In overcoming the challenges and illustrates a promising approach which is being pursued at :Mexicana de Cobre's 'La Caridad copper ore concentrator. At M de C, advanced ,control strategies have been 'installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, 'increased from 76;000 tpd to 90,000 tpd. Plantwide integration is expected' to gain an additional 3% improvement in profitability.

Jan 1, 1996

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

By Nils Eivind Kamfjord, Mari K. Næss, Halvard Tveit, Edin H. Myrhaug

"As a part of the FUME research programme being done by the Norwegian Ferroalloy Research Association (FFF), the SINTEF Group and NTNU, several measurements towards quantifying the gaseous and solid emissions from the draining of the silicon furnaces for metal have been carried out.Based on the measured size distribution of the formed fume particles and known particle growth theory, an estimate of the growth time for the given particles has been calculated. The formation time for the measured NO amount has also been calculated based on the fume measurements and a thermodynamic model of the furnace gases combusting with air. The two “formation” times are in the same order of magnitude and they are therefore used as parameters in a CFD model, modelling that the formed fume particles are heating up the surrounding air and thereby forming NO according to the Zeldovich mechanism. The measurements show an approximately equal constant NO formation per fume particle. The CFD model shows results in the same order of magnitude, supporting that the particle growth and NO formation happen under near stoichiometric conditions and are controlled by the formation of SiO2 fume.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2) formed during combustion of fuels. The main sources for human made NOx emissions is on-/offshore transportation industry, power generations based on fossil fuels, agriculture and other industries [1]."

Jan 1, 2012

By Rui-Qing Li, John G. Peacey, Peter J. Hancock

"Noranda has been investigating a pyrometallurgical process for the direct recovery of zinc from zinc concentrate and zinc and iron containing residues. The process consists of injecting dry zinc concentrate and secondary zinc materials into a molten iron oxysulphide bath, volatilizing metallic zinc into furnace off gas essentially free of sulphur or S02, fixing sulphur contained in the feed materials as iron oxysulphide matte which is disposed, and recovering metallic zinc in an ISP type lead splash condenser. Combustion of petroleum coke with air or oxygen enriched air inside the oxygen containing matte supplies part of the heat, and the products of combustion dilute the zinc-laden gas to a desired level.This paper describes the process concept, thermodynamic background, experimental tests, mass and heat balance calculation for a conceptual flowsheet, environmental stability of the residue and advantages and disadvantages of the process. Experimental tests have successfully proved the process concept and thermodynamic predictions. Direct smelting of zinc concentrate and residues inside an iron oxysulfide bath has a great potential to become a cost effective and flexible zinc smelting process.1. INTRODUCTIONZinc is mainly produced by a roast-leach-electrowinning process route, which accounts for about 80% of the world primary zinc production. This process produces high quality zinc with very high zinc recovery (>95%) but suffers from several major drawbacks such as using high cost electricity as reductant, producing environmentally problematic iron containing leach residue (jarosite or goethite) and the difficulty in treating secondary zinc feed materials containing high impurity levels, such as electric arc furnace dusts from the steel industry, and other complex sources. Also in some areas, markets for sulphuric acid are distant resulting in negative realizations on acid sales.The Imperial Smelting Furnace (ISF) process is the major pyrometallurgical process to treat zinc-lead concentrate. The advantage of this process over the electrolytic zinc process is its flexibility in treating high-lead, bulk concentrates with high recoveries of lead, copper and precious metals. However, this is a two-stage process involving sintering of Zn-Pb concentrates followed by blast furnace reduction. The process requires large amounts of high-quality coke which is a major operation cost, and the sintering process which results in serious environmental problems."

Jan 1, 1996

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By John Dasher

One of our War Plants processed Bolivian concentrates as low as 17% Sn by the Arnhem process (pressure leach with HCL) and sent the waste acid down a ditch to Galveston Bay where the chlorides, mostly iron, hydrolyzed. Oyster men, and Texas, demandedimpoundment until a disposal process could be developed. A recycle process found by lab work was recommended, piloted and a plant built. This involved cementation of As Sb, Cu, Bi and Ag on light moving scrap iron and of Sn & Pb on Al turnings (then not recyclable), evaporation and crystallization of hydrous FeCl2, roasting crystals in a muffle furnace and absorbing HCI for reuse. The residue from leaching the low grade concentrates was floated to remove undissolved sulfides, classified and passed over sand and slimes tables to get a smeltable concentrate, a discardable sand tail and a slimes tail worth treating After desliming at 2 micro meters cassiterite, oxide flotation gave good, lab results; but commercial equipment wasn't adequate then. Chloride volatilization, with or without smelting gave high recoveries of Sn as SnCl2, whose marketing was questionable. I have heard this was finally fluxed and smelted.

Jan 1, 1992

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of heptamolybdate ion in aqueous solution appearing in the literature and the absence of its standard pattern, the comparative investigations on Raman spectral pattern of saturated solution of ammonium heptamolybdate tetra hydrate were done. The results showed that the main vibrant frequencies of Raman spectral pattern of the saturated solution were in good agreement with those introduced in the literature, and that the intensity ratio (4.4) of the strongest peak to the second strongest peak recorded in Raman spectrum of the saturated solution had three obvious characteristics: it was greater than each of the results (ranging from 3.7 to 1.3) reported in the literature, much closer to that (4.7) of crystal and well conformed to the change rule of Raman spectra occurring in the process of the first-step polymerization of acidified molybdate solution. It was found that Raman spectrum of heptamolybdate ion in aqueous solution was determined by not only the main vibrant frequencies but also the intensity ratio, which is also the crucial result in this study. The comparative investigations indicate that the pattern of Raman spectrum of the saturated solution is the standard pattern of Raman spectrum of heptamolybdate ion in aqueous solution essentially. The affirmed standard pattern is reliable and can be used to the identification of heptamolybdate ion in aqueous solution, applied in the research of the equilibrium of acidified molybdate solution and the exploration of the best technologic condition for the production of high quality heptamolybdates.

Jan 1, 2006

By Qiang Zhong, Qian Li, Yongbin Yang, Tao Jiang

Thermogravimetric analysis (TGA) has been used to research the pyrolysis and combustion processes of coal used in rotary kiln of iron ore oxide pellet. Furthermore, the effects of air flow and oxygen concentration on the combustion behavior of coal were examined with TGA. The results showed that two individual stages can be distinguished for the pyrolysis of coal, the water evaporation stage and the de-volatilization stage. And the information on ignition and burnout characteristics can be obtained from the combustion process analyzed by TGA. Large air flow almost has no effect to the combustion process except that it enhances combustion intensity. However, the combustion process is further accelerated under oxygen-enriched conditions. With all experimental results, it could provide an attractive approach of analyzing coal for the rotary kiln process.

Jan 1, 2016

By K. J. Murphy, A. R. Smith, A. P. Odorski

"The need for large quantities of oxygen for use in metallurgical processes was a major driving force in the commercialization of tonnage air separation plants. Oxygen, nitrogen and argon impact the quality, energy efficiency and environmental aspects of metals production. Cryogenic air separation processes have been used to supply most industrial requirements, however, newer technologies are available or under development to meet the needs of today's and tomorrow's metallurgical processes. This paper reviews the technical features and state of development of adsorption, chemical, cryogenic and membrane technologies. The technologies are compared in terms of plant size, oxygen purity and pressure, nitrogen and argon co-production, product use pattern and back-up requirements. Computer control systems are described that optimize operation over varying load patterns and ambient conditions; substantially lowering energy consumption. IntroductionOxygen production totalled 390 billion cubic feet in 1987. Although current production is lower than the peak of 455 billion cubic feet reached in 1979, oxygen remains the fifth leading chemical product manufactured in the u.s. (1) Metals manufacturing and fabrication accounts for sixty percent of the oxygen consumed in the u.s. Oxygen use in the steel industry consists of air enrichment for conversion of iron ore, purification of the iron in basic oxygen or other furnaces, and for cutting and welding the finished steel product. Nonferrous ores are smelted in oxygen enriched atmospheres to reduce energy consumption and increase capture of sulfur compounds to meet environmental requirements. In the future oxygen usage is expected to become even more important in metals production as energy costs increase, environmental standards become more stringent, and as new coal based processes become commercialized. Oxygen usage per ton of metal in the new direct reduction processes can be up to ten times higher than traditional steel making."

Jan 1, 1988

By Magnus Ek, Peter Olsson

The Rönnskär Smelter has been faithful to Peirce Smith Converting during its 79 years of existence. Though a visitor to our smelter museum will easily find out that a lot has happened since the beginning – and development continues. In this paper an up-date on Converting and Casting at the Rönnskär Smelter is presented. Recent developments include an investment into converter process gas handling, but also day-to-day operational aspects such as converter aisle productivity and flexibility, but also minimal EH&S impact. 127

Jan 1, 2009

By B. W. Lightfoot, Neill F. Arthur

"The AusIron process is a new development of the well established Ausmelt bath smelting technology(l). The development of this technology has been tied to the South Australian Steel and Energy (SASE) project which brings dedicated coal and iron resources together with this new technology. SASE is a joint venture between Ausmelt (40%), Meekathara Minerals (40%) and the South Australian Government through Mines and Energy South Australia (MESA) (20%). It will use a multiple lance furnace to process iron ore using steaming coal for both fuel and reductant.It is intended to build the simplest plant economically possible. Refinements such as preheating and prereduction of the ore are compatible with the technology but are not expected to be necessary in the first generation plant.The joint venture is negotiating with suitable partners for funding of the project through to commercial implementation at a target scale of2.5 mt/a of pig iron.ObjectivesAusIron aims to produce pig iron directly from steaming coal and from any of a variety of iron sources in a simple furnace system with a minimum of pre-processing of either coal or iron ore. Preheating and prereduction of ore are compatible with the technology but may not be necessary. The immediate aim is not to be the technology that uses the least quantity of coal to produce iron metal but rather the technology that uses the least number of dollars to produce metal.The chemistry of iron making is well known, probably better known than that of smelting of any other metal. Iron has been made for thousands of years and it is possible to make iron from charcoal and ore in a simple blast furnace the size of a beer barrel. The focus is therefore not making iron but rather making it more cheaply than it is made by current technologies. Large blast furnaces now set the standard and new technologies must perform better if they are to gain market share. It is still the cost of iron, energy units and capital going into these mega blast furnaces which ultimately set the market price for pig iron."

Jan 1, 1996

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Bianca Medeiros, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Daniella Cardoso Buzzi, José Roberto de Oliveira

"AMD is one of the main problems associated with mining activities and the techniques used in their treatment may be the biosorption. The aim of this work was to study the rice husk as a biosorbent for the AMD treatment keeping constant: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). And varying the contact time of 5, 20, 60 and 240 minutes. Rice husk samples will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. Since the infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests. AMD synthetic solutions will be analyzed by ICP in order to quantify the metals concentration captured by biomassIntroductionThe preoccupation for the environment has led the industry in general, to treat their waste. As the only industrial activity is increasing, the pollutants generated must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.In mining there is waste water with accumulation of heavy metals, and these are harmful to health of living beings, thus being one of those industries responsible for some pollution of the environment. These wastewater in contact with oxygen to generate an acidic water is called acid mine drainage (AMD). This aqueous solution has a pH below 3 and varieties of dissolved metals. When this solution comes in contact with water, generates a series of environmental problems, so there is a need to recover the metals present in the DAM."

Jan 1, 2012

By T. Thuy Minh Nguyen, Sathish K. Lageshetty, Paul Bernazzani

The addition of nanoparticles to epoxy resins often results in changes in the physical properties of the material particularly when dealing with thin coatings. By characterizing the mechanism of interactions between nanoparticles and polymer chains the material could be tailored for specific applications or properties such as enhanced biodegradability. This study compared the characteristics of common DGEBA resin coated on a silicon substrate and embedded with nanoparticles of TiO2 and Fe2O3. Specifically, we investigated the rate of curing, and the thermal stability of these nanocomposites. Results show changes in the stability for compounds containing TiO2, while Fe2O3 significantly enhanced the curing rates of the nanocomposites while maintaining similar physical properties.

Mar 1, 2017

By LeoJ. Miller

Exploration for an ore deposit commences with an outline of the regional ore controlling environment and is followed by the application of tools to focus the target area. One of the most essential focusing is the mapping of the mineral assemblages within the area of the ore. Key elements of mineralizing fluids, either epigenetic or syngenetic, enter into mineral assemblages that extend far beyond ore deposits. Portions of these assemblages may consist of new matrix minerals or alteration of previously existing minerals. Today, ore deposits are divided into genetic classes and each class is d8fined by a specific geological environment. Ore deposits within a given class are associated with a mineralogy, that is characteristic of the ore deposit class. So faithful is the mineral assemblage surrounding, or within an ore deposit, that recognition of the assemblage may be sufficient to define the class. Porphyry copper deposits have long been noted for their halos of alter-ation minerals. The outermost ring of chlorite, epidote and calcite extend thousands of feet away from the main ore zone. The mineral associated with porphyry copper deposits have been well documented by our distinguished speaker Paul Kerr, at Santa Rita (1), and Silver Bell' (2), and by excellent papers from S. C. Creasey, 1959 (3), Sales, 1948 (4), T. S. Lovering, 1949 (5), our Co-Chairman John Guilbert, 1970 (6), and many others. Several recent porphyry copper mines have been discovered in recent years by utilizing the mineral assemblage model described by Lowell and Guilbert, 1970 (6). Dave Lowell applied his own model of mineral halos for the discovery of Kalamazoo at San Manuel (7), Arizona, and Casa Grande West, Arizona. The purpose of this paper is to outline the application of mineralogy for discoveries of deposits other than porphyry copper mines and in particular, to ore discoveries in which mineralogy has played a key roll.

Jan 1, 1981

By Dirk van Zyl

As part of the North American regional activities during the Mining, Minerals and Sustainable Development Project (MMSD) one project focused on the development of sustainability evaluations at the operations level. Engagement was identified as one of the seven important questions to be addressed. Engineers and scientists employed in the mining, minerals and materials production arenas must understand the importance of stakeholder engagement, both within and outside the operations as it is essential in the ongoing activities required to contribute to sustainable development. After developing the awareness that a social license can only be contemplated if engagement is in place, they also have to develop skills in engagement processes. This presentation will present the business case for engagement as well as an approach to motivate undergraduate mining engineers to embrace it. The presentation will also review some recent and ongoing research to improve the engagement process.

Jan 1, 2010

By Patrick R. Taylor

Glass is used for immobilization of radioactive and hazardous wastes due to its durability and ability to accept a variety of waste constituents into its network structure. Alternative high temperature vitrification techniques have the advantage of increased throughput, increased waste loading and being applicable to variable and heterogeneous waste streams. However, the increased processing temperature places further concerns on the increased volatilization of contaminants, and increased corrosion and erosion of me Iter components. A database of melt properties at higher temperatures, such as partitioning, viscosity, density and electrical conductivity, in the temperature range of 1400-20000 K are being developed.

Jan 1, 2000