Search Documents

By Qingyu Deng, Shiwei Ma, Wang Hua, Guibao Qiu

"The flow properties of the blast furnace slag bearing high TiO2 at high temperature like the viscocity may change a lot due to the formation of the carbonitride inside, causing serious problems on the separation between the metal and the slag. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process with iron ore bearing titania. In this study, the formation of Ti(C,N) in blast furnace and the influences of various factors on the Ti(C,N) formation are investigated by FactSage. It is found that the mass of Ti(C,N) would reach the maximum at 1480 oC, and the product is mainly TiN below 1620 oC, while it is mainly TiC above 1620oC. The order of the factors by the importance from strong to weak was: temperature, the content of TiO2 in slag, basicity of slag, the content of MgO and Al2O3.IntroductionThe titanium dioxide (TiO2) in iron ore bearing titania will be partly reduced by carbon to titanium carbonitride (Ti(C,N)) in blast furnace, causing serious problems on the separation between the metal and the slag because of the change of flow property. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process, especially for the smelting of iron ore bearing titania. Extensive experimental data in regard to the formation of Ti(C,N) has been reported in numerous papers[1-6]. However, only some discrete data can be obtained by experiment, and it is difficult to detect the mass of Ti(C,N) in slag. In addition, the experiment is difficult to be proceeded when the temperature is above 1600oC. Therefore, it is very difficult to make clear the critical condition of the formation of Ti(C,N) by experiment."

Jan 1, 2012

By N. E. Idenyi

The effects of compositions and firing temperatures on the physico-mechanical properties of blended Nsu fireclay and Nkalaha redbrick clay have been investigated. The clay samples were compounded according to the following ratios: 10:90, 20:80, 30:70, 40:60 50:50, 60:40, 70:30, 80:20 and 90:10 in the order Nsu: Nkalaha respectively, and test samples made and fired at 9000C, 10000C 11000C and 12000C. The properties tested for were the modulus of rupture, porosity, shrinkage, apparent density, water absorption and bulk density. From the results obtained, it is inferred that the blends have a maximum service temperature of 11000C, with the 30: 70 blend presenting the best characteristics. A conclusion is drawn to the effect that the blend could be adapted for the production of ceramic earthenware, electrical porcelain pin insulators, cement manufacture and for refractory linings where temperature requirements are less severe.

Jan 1, 2006

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuOo.5- CaO-MgO-FeOu-AlO15-SiO2) slags were calculated. The log (PO2/PS2) versus matte grades of various industrial processes was determined. The PO2/PS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Katsunori Yamaguchi

Secondary materials, that contain relatively high concentrations of platinum group metals, (PGMs) are treated in copper smelting process. The PGMs lost in the slag is increasing with increasing quantities of scrap treated amount. To determine the portion of the PGMs chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. An experimental study was carried out to determine the distribution of palladium between the FeOx–SiO2 slag and the liquid Cu2S–FeS matte at 1573 K and a fixed partial pressure of SO2 of 0.1 atm. It was found that the distribution ratios are around 10−3 for platinum and palladium. The distribution ratios show a tendency to increase when the grade of matte is increased above 60 mass% Cu. In addition, the solubility of platinum in FeOx–SiO2 slag equilibrated with a pure palladium and the Pd-Cu alloy was determined at 1573 K and the range of oxygen partial pressure from 10−9 to 10−7 atm. The solubility of palladium in the slag tends to increase with increasing oxygen partial pressure and activity of CuO0.5 in the slag.

By Muhammad A. Imam, Ramana G. Reddy

This study provides a reasonable evaluation of the Mg-B binary system. Magnesium and Boron (Mg-B) alloys were investigated to determine their thermodynamic properties employing solid state electrochemical cells based on CaF2 electrolyte represented as –Pt; Ar= MgþCaMgF4 f gCaF2 k kf½Mg B alloy þ CaMgF4 g=Ar; Pt+ Investigations were performed over the temperature range of 773–873 K to measure the electromotive force (EMF), which was used to derive the partial Gibbs Free energies of the alloys in the composition range of XB = 0.07 to 0.95. The activities of Mg were also calculated from partial Gibbs Free energies. The activities of Mg in MgB2, MgB4, and MgB7 were expressed as a function of temperature respectively, ln aMg = 4.27–9.32 × 103/T, ln aMg = −7.54 + 6.67×103/T, and ln aMg = 4.93–19.57 × 103/T, where T is the temperature in K. From this expression, the activity of Mg for these intermediate phases can be extrapolated at a higher temperature to get the accurate phase boundaries for the Mg-B system.

Mar 1, 2017

By Matthias Frommer, Carl-Peter Reipl, Reinhard Flende

"Today there is a growing demand for strip of superior steels with specifically tailored technological properties. Especially strips of high-strength, micro-alloyed steel grades applied to manufacture longitudinally and spiral-welded pipes are a growth market. Tubes are generally required to have high strength and sufficient toughness values and thus favour specific hot strip microstructures. The correlation of chemical analysis, process parameters and mechanical properties with microstructural features is still a challenging task. During the last decades, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) have become useful tools for the characterization of complex microstructures. The EBSD data provides an immense variety of post-processing possibilities, e.g. related to grains, grain boundaries, misorientations or texture. This paper highlights the results of an advanced analysis of microstructures representing industrial produced hot-rolled strips and presents an approach to define and quantify some essential microstructural parameters.IntroductionHigh-strength microalloyed steels have been used for the production of welded pipes for more than 30 years. However, the alloy design of pipeline grades is being continuously modified and the process technology optimized because of the increasing high strength-toughness combination requirement for pipeline steels. Compact strip production (CSP®) technology is an upcoming promising route for the production of high-quality pipeline steel grades [1]."

Jan 1, 2012

By N. Shi, T. C. Lowe, S. J. Zhou, M. L. Lovato, Y. T. Zhu, J. A. Valdez, W. R. Blumenthal, M. G. Stout

"A major problem of short-fiber composites is that the interfaces between the fiber and matrix become a limiting factor in improving mechanical properties such as strength. For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber, thus reducing the ineffective fiber length. However, a strong interface will make it difficult to relieve fiber stress concentration in front of an approaching crack. Stress concentrations result in fiber breakage. We report in this paper an innovative approach to overcome this problem: reinforcement morphology design. Short-fibers with enlarged ends are processed and used to reinforce a polyester matrix. The initial results show that the bone-shaped short-fibers produce a composite with significantly higher strength than can be attained with conventional short, straight fibers.IntroductionThese interfaces between the fiber and the matrix in short-fiber composites play a critical role and, in many cases, become a limiting factor in improving such mechanical properties as strength and toughness of the composites (1-4). For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber. A stronger interface can reduce the ineffective length at both ends of the fiber and, therefore, can increase the effective length that carries load (5-9). However, with a strong interface it is difficult to relieve fiber stress concentration -in front of an approaching crack; and such stress concentration can result in fiber breakage (10, 11). This effect is particularly severe for ceramic matrix composites, because of their low matrix toughness and lack of plasticity. Even for a composite with a highly ductile matrix, such as plastics, too strong an interface may still cause successive adjacent fiber breakage and subsequently reduce composite toughness (1, 11). On the other hand, a weak interface significantly decreases the fiber load-carrying length due to ineffective load transfer and complete fiber interfacial debonding and pullout during loading. A compromise in the interfacial bond strength will also compromise the load-carrying potential of short fibers."

Jan 1, 1998

By Jie Ma, Shun-Li Zhao, Jian Zhao, Jie-Yu Zhang

"Microstructural morphology evolution of Ni-45wt.%Mo droplets during rapid solidification process was investigated using an advanced modified 3D cellular automaton-finite element(CAFE) model by CALCOSOFT software. The model was modified by User-defined functions (UDFs) and validated with experimental solidification microstructural morphology of Ni-45wt.%Mo droplets available in the literature. Then, the influences of convection heat transfer coefficient, superheat of the alloy droplets and droplets size were investigated during the rapid solidification process. The predictions show that microstructural morphology is obviously sensitive to convection heat transfer coefficient and droplet size. With the decrease of convection heat transfer coefficient, the grain density decreases. In addition, the decrease of the droplet size could obtain refined microstructure. However, decrease the superheat ofNi-45wt.%Mo droplets has little effect on microstructural morphology.IntroductionFor several decades, much attention has been paid to undercooled alloy droplets of rapid solidification process for which can obtain refined microstructure, decreased microsegregation and extended solubility of alloying elements [1-3]. Extensive prior work shows that solidification of droplets plays an essential role in advanced material properties [ 4]. Consequently, it is very important to investigate the microstructural morphology evolution, especially for dendrite growth during non-equilibrium solidification process, for dendrite growth reflected the kinetics of the crystal growth process."

Jan 1, 2013

By R. Padilla, M. C. Ruiz

Arsenic, antimony and bismuth are commonly found in copper concentrates usually as the minerals enargite, stibnite and bismuthinite, respectively. Concentrates having high levels of arsenic and antimony must be pretreated before smelting. Roasting is the preferred method for removing these toxic impurities from concentrates; However, the removal of As, Sb and Bi in oxidizing roasting by volatilization may not be complete due to the slow reaction rates at 500- 700 °C. Oxidizing/volatilization data were obtained from pure mineral mixtures and from arsenic rich copper concentrate. The reaction mechanism for the volatilization of arsenic and antimony were discussed. Near 100% As and over 95% Sb volatilized in the oxidation of a mixture of pure minerals at 700 °C, 1% oxygen, while over 95% As, and 35% Sb volatilized at 600 °C in 1% oxygen atmosphere when using a copper concentrate containing 3.51% As, 0.14% Sb, and 0.01% Bi. Bismuth did not volatilize.

Jan 1, 2015

By J. N. Hryn, E. J. Daniels, M. Askew, Kirchner. G.

This presentation addresses the changing regulatory climate towards aluminum dross and salt cake in Europe and in the United States. Although sporadic, the trend in the U.S. continues to be away from command-and-control regulation of these materials. This trend began in the early 1980s when the Environmental Protection Agency was successfully sued in court and prevented from classifying dross as a hazardous material. The situation in Europe is different. Because of Council Directive 96/61/EC from the European Commission, European Union member countries have all passed legislation that will essentially cause all salt cake and drosses to be reprocessed. The implementation date of the legislation varies from country to country: from 2001 in the United Kingdom to 2007 in Germany, France, Austria, Italy, and Spain. The European aluminum industry is urging the EC to use the approach adopted by the U.S. EPA, which declassifies the majority of aluminum drosses and salt cakes.

Jan 1, 2000

By Dieter Neuschiitz, Pengfu Tan

"In order to understand the sintering phenomena during iron ore sintering process, a CFD model of iron ore sintering has been developed, combining with the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. This CFD model can be used to simulate the concentrations of the gaseous and solid species, temperatures of the gas and solid, melting and molten fractions of the mixture, gas velocities, temperature zones and residence times of the gas in each temperature zone. IntroductionThe off-gas analyses clearly revealed that the off-gas of a sinter strand does not have a composition corresponding to thermodynamic equilibrium, for example, the CO, CO2 and O2 concentrations are not the mutually consistent equilibrium values. Apparently the chemical reactions in the sinter bed are controlled kinetically. Therefore kinetic modeling of sintering reactions combined with CFD modeling is necessary to understand the sintering phenomena during iron ore sintering process.Several models of iron ore sintering have been developed since 1970 [l-l 4l, each being more refined than its predecessor. The models were formulated as a series of differential equations to describe chemical and physical changes occurring at a point in the bed. These equations were solved numerically in a vertical plane along the strand. The present CFD model, based on the Nath's model [14], has been published in the reference [15]. In this work, some new chemical kinetic models of gas-solid reactions are incorporated in the present CFD model. The concentrations of gaseous and solid species, temperatures of gas and solid, melting and molten fractions of solid, velocity of gas, and residence time of gas in each combustion zone can be calculated by this model."

Jan 1, 2004

By Tullio Corsini

Scrap battery recovery process, developed by Engitec Impianti S.p.A., is improved transforming batches operations in continuous. Benefits expected: constant and better quality of the products; easier and more reliable control of the operating parameters, reduction of manpower requirements. Paste will content less sulfate, particularly in soluble form. Sodium sulphate is obtained with higher and constant purity.

Jan 1, 1993

By M. Jennings

In 1987, Echo Bay discovered a major silver/gold ore body at their McCoy property in Nevada, and quickly made a decision to build a 5000 tpd mill which was expanded during the design to 7500 tpd. Since the ore reserves consisted of cyanide leachable oxide as well as sulfide, the plant flow sheet involved an oxide leach, a gravity circuit, and lead sulfide and a pyrite sulfide recovery by flotation. The paper describes the process development, equipment selection, plant design and the startup of the oxide treatment.

Jan 1, 1990

"Mechanical alloying (MA) synthesizing technology and thennohydrogen processing (THP) were utilized to produce nanocrystalline Ti-MMC's reinforced by TiB intermetallic compound by using TiH2-B powder mixtures. Powders MA'ed up to 8 hours were examined by X-ray diffraction and SEM study. All MA'ed powders afterwards were HIP'ed at 700, 800 and 950EC for 1 hour. Detailed XRD, SEM and TEM study of the samples were carried out to determine the structure and micrography of the Ti-TiB MMC material processed by MA+THP approach followed by HIP'ing at high temperatures.IntroductionThe fiber reinforced titanium base composites [1,2] which possess a great resistance to high temperature have been investigated. In these studies fibers of C and SiC were used as reinforcing materials. However, these fibers react with Ti-matrix at elevated temperature resulting in product formation at the interface between the matrix and the fiber. Because of the chemical reactions, strength of the product MMC material diminishes.In conventional techniques of whisker reinforced composite material production, the mixtures of matrix metal powders and dispersed fibers are consolidated by hot pressing, HIP and/or hot extrusion. These techniques, however, have some shortcomings. Hard and brittle fibers could be broken during mixing cycle of the processing. Consolidation techniques could also be the cause for fiber breakdown. Attaining of the uniform dispersion of fibers into the metal matrix is not an easy process. The chemical reactions at elevated temperature exposures in the interface between the matrix material and fiber reinforcement cause product formations leading to poor mechanical properties."

Jan 1, 1998

By E. V. Redin, B. A. Dubrovsky, E. V. Knyazev, A. I. Starikov

"Ti-V magnetite is one of the most abundant composite ore resources in the world. This ore cannot be fully processed via blast furnace technology because of high content of Ti02. According to the investigations carried out in the USA and Japan ITmk3 RHF (Rotary Hearth Furnace) technology is a breakthrough in Ironmaking. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from Ti-V magnetite ore via the ITmk3 by means of the lab scale testing. Samples of ore from the Maly Kuybas deposit (Southern Ural), carbon reductant and fluxes were chemically analyzed. Green pellets were processed via a lab chamber furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities [l]. After pilot testing at Kobe Steel's Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics put into operation the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota) in 2010. Results were consistent with nugget characteristics confirming ITmk3' s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from the Ti-V magnetite bearing ore with high content of Ti02 and Alz03 has been done. It is well known, if a lot of Ti02 and Alz03 enter the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace. Besides, high content of Alz03 raises the melting temperature of gangue minerals disturbing the coalescence of reduced iron to the nuggets."

Jan 1, 2013

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re-melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By Patrick R. Taylor

The synthesis of high-purity ultra-fine barium strontium titanate powders (BST: BaO6Sro.4TiO3) has been performed in a non-transferred are D.C. thermal plasma reactor. Slurries of aqueous solutions of dissolved barium and strontium nitrates and solid titanium dioxide powders were used as precursors. Oxygen and argon were used as carrier gases, and pure argon and combinations of argon and nitrogen were used as plasma gases. The plasma torch power was varied, as well as the oxygen flow rate and the total molar concentration of the precursors. A graphite plate was designed to protect the torch electrode and lower the level of impurities in the product. A thermochemical analysis of the Ba(NO3)2-Sr(NO3)2-TiO2-H2O-O2 system was performed to predict the conditions for the formation of BST and the feasibility of the reaction, The powders collected from the different sections of the reactor were characterized using Transmission and Scanning Electron Microscopy, X-Ray Diffraction, and ICP chemical analysis. The powders produced showed high conversion to BST, ultra-fine particle size (< 30 rim) and high purity, which makes this a potential process to produce ceramic materials for electronic devices.

Jan 1, 2003

By Haibin Wang, Baojun Zhao, Xueyi Guo, Zhixiang Cui, Zhi Wang

In conventional copper production, anode copper is produced from concentrate in three furnaces in a process that entails four oxidation steps and one reduction step. Three types of slags are produced that require further treatment to recover copper. Dongying Fangyuan Nonferrous Metals recently developed a simplified process which requires only two custom-designed furnaces instead of the conventional smelting, converting and re fining furnaces. The first furnace continuously produces high-grade matte (>75 wt% Cu) that contains little iron (<2 wt% Fe). The liquid matte is continuously fed to the second furnace, which produces anode copper. The new process signi ficantly reduces the capital and operating costs and increases productivity and environmental sustainability. This paper presents fundamental concepts that enable the simpli fied process to be developed. The detailed operations in Dongying Fangyuan Nonferrous Metals are also described.

Mar 1, 2018

By R. A. Alock

The character, occurrence and genesis of the three types of nickel deposits, sulfide, laterite and deep-sea nodule are described, highlighting the differences in mineralogy and chemical composition that effect the extractive metallurgy of nickel and associated byproducts. World nickel production and current resources by deposit type and geographic location are also reviewed.

Jan 1, 1988

By C. B. Solnordal, R. N. Taylor

"The heat transfer conditions on the outer side of a Sirosmelt lance have been determined using experimental measurements in combination with a mathematical model. By measuring the temperature distribution along the wall of an operating Sirosmelt lance, as well as the thickness of the slag layer on it, it was possible to use the model to determine both the heat transfer coefficient between the vessel contents and the lance, as well as the effective thermal conductivity of the slag layer. The effective thermal conductivity of the slag layer was found to be within the range 0.7-1.3 W.m-1. ºCl, which was in good agreement with measured values for magnetite. The outside heat transfer coefficient varied from 80 to ISO W.m-2. ºC1, which was smaller than quoted in the literature for metal/slag systems. The discrepancy was attributed to the high thermal resistance experienced between the lance wall and the slag layer, as well as the large quantities of combustion gases that envelop the lance tip and reduce convection and conduction from the melt to the lance. INTRODUCTIONThe Sirosmelt submerged combustion smelting process [1] utilizes top injection lances to deliver fuel and air into a metallurgical melt. To help prevent lance failure from attack by liquid slag, helical vane swirlers are used within the annular lance to impart swirl to the flowing air and enhance the heat transfer from the lance wall to the air. The swirlers thus cool the wall, and enable a frozen layer of slag to form on its outer surface. This solid layer ensures liquid slag cannot reach the lance surface, and the lance is protected.A mathematical model of the heat transfer processes associated with the lance has been developed, which combines heat balance equations with engineering correlations to predict the wall and cooling air temperature of the lance, as well as the air pressure distribution. An account of the model was given by Rankin et al. [2]. To further enhance the model and enable it to predict the thickness of slag accumulating on the lance, a detailed analysis of the heat flow through the slag layer commenced in 1992. By far the most complex aspect of the model, the flow of heat from the vessel contents to the outside of the lance was dependent on many factors, including:-"

Jan 1, 1996